Advertisement

Tribology Letters

, 67:69 | Cite as

Effect of Silicon Content on the Wear Behavior of Low-Carbon Dual-Phase Steels

  • Ashkan NouriEmail author
  • Hossein Hassannejad
  • Morteza Farrokhi-Rad
Original Paper
  • 17 Downloads

Abstract

The aim of this study is to understand the influence of the silicon content and volume fraction of martensite obtained by intercritical annealing at three temperatures (750, 780, and 800 °C) on the wear behavior of low-carbon dual-phase steels. Dry sliding wear tests were carried out in three sliding intervals (0–200, 200–600, and 600–1000 m) by using a pin-on-disk machine at normal load of 30 N, room temperature, and fixed sliding velocity of 0.5 m/s. The weight loss of the specimens was measured and the wear rate calculated. For all the samples, the wear rate decreased with increasing sliding distance. The results of the present investigation clearly show that the effect of the intercritical annealing temperature is greater than that of the silicon content. Among the three tested temperatures, the wear resistance was more sensitive to the silicon content at the lowest (750 °C). Both the content and hardness of the martensite were factors affecting the wear resistance of the dual-phase steels. The wear response of the samples can be described on the basis of the interaction between the martensite volume fraction and hardness. The role of the silicon content in the oxidation of steels was also examined.

Graphical Abstract

Keywords

Dual-phase steel Silicon content Wear resistance Martensite content Microstructure 

Notes

Acknowledgements

The authors gratefully acknowledge the Research Board of Arak University for financial support (grant no. 93/7246) and the provision of the research facilities used in this work.

References

  1. 1.
    Jiang, Z., Liu, J., Lian, J.: A new relationship between the flow stress and microstructural parameters for dual phase steel. Acta Metall Mater 40, 1587–1597 (1992)CrossRefGoogle Scholar
  2. 2.
    Bag, A., Ray, K.K., Dwarakadasa, E.S.: Influence of martensite content and morphology on tensile and impact properties of high-martensite dual-phase steels. Metall. Trans. 30A, 1193–1202 (1999)CrossRefGoogle Scholar
  3. 3.
    Grushko, B., Weiss, B.Z.: Yield behavior of dual-phase steel. Scr. Metall. 23, 865–870 (1989)CrossRefGoogle Scholar
  4. 4.
    Nouri, A., Saghafian, H., Kheirandish, S.: Influence of volume fraction of martensite on the work hardening behavior of two dual-phase steels with high and low silicon. Int. J. Mater. Res. 101, 1286–1292 (2010)CrossRefGoogle Scholar
  5. 5.
    Wang, A., Rack, H.J.: Dry sliding wear in 2124 Al-Si Cw/17-4PH stainless steel systems. Wear 147, 355–374 (1991)CrossRefGoogle Scholar
  6. 6.
    Gocke, A., Schmite, I., Wilhelm, M.: Goring and sliding abrasion of austenitic manganese steels reinforced by hard phases. Wear 119, 313–327 (1987)CrossRefGoogle Scholar
  7. 7.
    Tyagi, R., Nath, S.K., Ray, S.: Development of wear resistant medium carbon dual phase steels and their mechanical properties. Mater. Sci. Technol. 20, 645–652 (2004)CrossRefGoogle Scholar
  8. 8.
    Jha, A.K., Prasad, B.K., Modi, O.P., Das, S., Yegneswaran, A.H.: Correlating microstructural features and mechanical properties with abrasion resistance of a high strength low alloy steel. Wear 254, 120–128 (2003)CrossRefGoogle Scholar
  9. 9.
    Abouie, V., Saghafian, H., Kheirandish, S.: Effect of microstructure on the oxidative wear behavior of plain carbon steel. Wear 262, 1225–1231 (2007)CrossRefGoogle Scholar
  10. 10.
    Ojala, N., Valtonen, K., Heino, V., Kallio, M., Aaltonen, J., Siitonen, P.: Effects of composition and microstructure on the abrasive wear performance of quenched wear resistant steels. Wear 317, 225–232 (2014)CrossRefGoogle Scholar
  11. 11.
    Wang, S.Q., Wang, L., Zhao, Y.T., Sun, Y., Yang, Z.R.: Mild-to-severe wear transition and transition region of oxidative wear in steels. Wear 306, 311–320 (2013)CrossRefGoogle Scholar
  12. 12.
    Modia, O.P., Pandita, P., Mondala, D.P., Prasada, B.K., Yegneswarana, A.H., Chrysanthoub, A.: High-stress abrasive wear response of 0.2% carbon dual phase steel: effects of microstructural features and experimental conditions. Mater. Sci. Eng. A 58, 303–311 (2007)CrossRefGoogle Scholar
  13. 13.
    Xu, X., Van der Zwaag, S., Xu, W.: The effect of ferrite-martensite morphology on the scratch and abrasive wear behavior of a dual phase construction steel. Wear 348–349, 148–157 (2016)CrossRefGoogle Scholar
  14. 14.
    Shukla, N., Roy, H., Show, B.K.: Effect of prior austempering heat treatment on the microstructure, mechanical properties and high-stress abrasive wear behaviour of a 0.33% C dual-phase steel. Can. Metall. Q. 55, 13–22 (2016)CrossRefGoogle Scholar
  15. 15.
    Modi, A.P.: Effects of microstructure and experimental parameters on high stress abrasive wear behavior of a 0.19 wt% C dual-phase steel. Tribol. Int. 40, 490–497 (2007)CrossRefGoogle Scholar
  16. 16.
    Sharma, A., Kumar, A., Taygi, R.: Erosive wear analysis of medium carbon dual phase steel under dry ambient condition. Wear 335, 91–98 (2015)CrossRefGoogle Scholar
  17. 17.
    Kalousek, J., Fegredo, K.M., Lauffr, E.E.: The wear resistance and worn metallography of pearlite, bainite and tempered martensite rail steel microstructures of high hardness. Wear 105, 199–222 (1985)CrossRefGoogle Scholar
  18. 18.
    Aksoy, M., Karamis, M.B., Evin, E.: An evaluation of the wear behavior of a dual-phase low-carbon steel. Wear 193, 248–252 (1996)CrossRefGoogle Scholar
  19. 19.
    Abouie, V., Saghafian, H., Kheirandish, S.: Mild oxidative wear behavior of plain carbon dual phase steel. Steel Res. Int. 78, 506–511 (2007)CrossRefGoogle Scholar
  20. 20.
    Stott, F.H.: The role of oxidation in the wear of alloys. Tribol. Int. 31, 61–71 (1998)CrossRefGoogle Scholar
  21. 21.
    Bayram, A., Uguz, A.: Effect of microstructure on the wear behavior of a dual phase steel. Mat.-Wiss. u. Werkstofftech. 32, 249–252 (2001)CrossRefGoogle Scholar
  22. 22.
    Bataev, A.A., Tushinskii, L.I., Bataev, V.A.: Effect of the ferrite-cementite on the rate of abrasion wear in structure steel. Met. Sci. Heat Treat. 38, 262–264 (1996)CrossRefGoogle Scholar
  23. 23.
    Xu, X., Van Der Zwaag, S., Xu, W.: The effect of martensite volume fraction on the scratch and abrasion resistance of a ferrite–martensite dual phase steel. Wear 349, 80–88 (2016)Google Scholar
  24. 24.
    Howmick, S.B., Show, B.K.: Effect of prior heat treatment on wear behavior of 0.23% carbon dual phase steel. Can. Metall. Q. 53, 93–99 (2014)CrossRefGoogle Scholar
  25. 25.
    Deng, X., Wang, Z., Tian, Y., Fu, T., Wang, G.: An investigation of mechanical property and three-body impact abrasive wear behavior of a 0.27% C dual phase steel. Mater. Des. 49, 220–225 (2013)CrossRefGoogle Scholar
  26. 26.
    Saghafian, H., Kheirandish, S.: Correlating microstructural features with wear resistance of dual phase steel. Mater. Lett. 61, 3059–3063 (2007)CrossRefGoogle Scholar
  27. 27.
    Davies, R.G.: Influence of silicon and phosphorous on the mechanical properties of both ferrite and dual-phase steels. Metall. Trans. 10A, 113–118 (1979)CrossRefGoogle Scholar
  28. 28.
    Mondal, D.K., Ray, R.K.: Effect of chemical composition and initial heat treatment on the structure and properties of a few dual-phase steels. Steel Res. Int. 60, 25–32 (1989)CrossRefGoogle Scholar
  29. 29.
    Nouri, A., Saghafian, H., Kheirandish, S.: Effect of silicon content and intercritical annealing on manganese partitioning in the dual-phase steels. J. Iron Steel Res. Int. 17, 46–51 (2010)CrossRefGoogle Scholar
  30. 30.
    Nouri, A., Kheirandish, S., Saghafian, H.: A study of redistribution of silicon in dual-phase silicon steels. Met. Sci. Heat Treat. 59, 569–574 (2018)CrossRefGoogle Scholar
  31. 31.
    Dehoff, R.T., Rhines, F.N.: Materials Science and Engineering Series. McGraw-Hill Book Company, New York (1968)Google Scholar
  32. 32.
    Takadoum, J.: Materials and Surface Engineering in Tribology. Wiley, New York (2008)CrossRefGoogle Scholar
  33. 33.
    Rocha, R.O., Melo, T.M.F., Pereloma, E.V., Santos, D.B.: Microstructural evolution at the initial stages of continuous annealing of cold rolled dual-phase steel. Mater. Sci. Eng. A 391, 296–304 (2005)CrossRefGoogle Scholar
  34. 34.
    Rizk, A., Bourell, D.L.: Dislocation density contribution to strength of dual-phase steels. Scr. Metall. 16, 1321–1324 (1982)CrossRefGoogle Scholar
  35. 35.
    Jena, A.K., Chaturvedi, M.C.: On the effect of volume fraction of martensite on the tensile strength of dual-phase steel. Mater. Sci. Eng. 100, 1–6 (1988)CrossRefGoogle Scholar
  36. 36.
    Sarwar, M., Priestner, R.: Hardenability of austenite in a dual-phase steel. J. Mater. Eng. Perform. 8, 380–384 (1999)CrossRefGoogle Scholar
  37. 37.
    Tyagi, R., Nath, S.K., Ray, S.: Effect of martensite content on friction and oxidative wear behavior of 0.42 Pct carbon dual-phase steel. Metall. Trans. 33A, 3479–3488 (2002)CrossRefGoogle Scholar
  38. 38.
    Sullivan, J.L., Quinn, T.F.J., Rowson, D.M.: Developments in the oxidational theory of mild wear. Tribol. Int. 13, 153–158 (1980)CrossRefGoogle Scholar
  39. 39.
    Amano, T., Yamada, K., Okazaki, M., Takeda, M., Onishi, T.: High temperature oxidation of Fe-Si alloy. Mater. Sci. Forum 461–464, 169–174 (2004)CrossRefGoogle Scholar
  40. 40.
    Amano, T., Okazaki, M., Takezawa, Y., Shiino, A., Takeda, M., Onishi, T., Seto, K., Ohkubo, A., Shishido, T.: Hardness of oxide scales on Fe-Si alloys at room and high temperatures. Mater. Sci. Forum 522–523, 469–476 (2006)CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  • Ashkan Nouri
    • 1
    Email author
  • Hossein Hassannejad
    • 1
  • Morteza Farrokhi-Rad
    • 2
  1. 1.Department of Metallurgy and Materials Engineering, Faculty of EngineeringArak UniversityArakIran
  2. 2.Department of Materials EngineeringAzarbaijan Shahid Madani UniversityTabrizIran

Personalised recommendations