Effect of Turbulence and Roughness on Coupled Porous-Medium/Free-Flow Exchange Processes
- First Online:
- Received:
- Accepted:
Abstract
The interactions between turbulent free flow and flow in a porous medium are of key interest in different fields, e.g., meteorology, agriculture, building physics, and aerospace engineering. Properly understanding the strongly coupled exchange processes between the two domains is crucial to describing these interactions. In (Mosthaf et al. in Water Resour Res 47(10):W10522, 2011. doi:10.1029/2011WR010685), a concept for coupling laminar compositional single-phase free flow to compositional two-phase porous-medium flow under non-isothermal conditions was presented. In this study, the existing coupling concept is first extended to turbulent free-flow conditions. This includes the interface conditions between a Reynolds-averaged Navier–Stokes free flow using algebraic turbulence models and a Darcy porous-medium flow. Second, eddy viscosity and boundary layer models for a rough interface are integrated into this model concept. Results from laboratory evaporation experiments are used for comparison of the developed model concept. A sensitivity analysis of the evaporation rate and porous-medium quantities on different model setups, boundary conditions, Beavers–Joseph coefficients, and roughness lengths is performed. Results demonstrate how including turbulence, either with eddy viscosity or boundary layer models, affects the evaporation rate. The model concept is able to predict early stage-I and intermediate to later stage-II evaporation rates. Sand-grain roughness concepts are successfully included into the model and show the desired qualitative effect.
Keywords
Evaporation Roughness Turbulence Porous-medium/free-flow interfaceNomenclature
- \(\alpha _{\text {BJ}}\)
Beavers Joseph coefficient
- \(\alpha _{\text {vg}}\)
Van Genuchten parameter (\(1/\mathrm{Pa}\))
- \(\alpha \)
Phase index: liquid (l) or gas (g)
- \(\delta _{\text {v}}\)
Viscous sublayer thickness (m)
- \(\kappa \)
Component index: water (w) or air (a)
- \(\kappa \)
Von Kármán constant
- \(\lambda \)
Thermal conductivity (\(\mathrm{W}/(\mathrm{m\, K})\))
- \(\lambda _{\text {pm}}\)
Effective porous-medium thermal conductivity (\(\mathrm{W}/(\mathrm{m}\, \mathrm{K})\))
- \(\lambda _{\text {s}}\)
Thermal conductivity of the solid material (\(\mathrm{W}/(\mathrm{m K})\))
- \(\lambda _{\text {t}}\)
Eddy thermal conductivity (\(\mathrm{W}/(\mathrm{m\, K})\))
- \(\nu \)
Kinematic viscosity (\(\mathrm{m}^2/\mathrm{s}\))
- \(\nu _{\text {t}}\)
Kinematic eddy viscosity
- \(\phi \)
Porosity
- \(\tau \)
Tortuosity
- \({\bar{\tau }}_\text {t}\)
Turbulent and laminar shear stress (\(\mathrm{kg}/\mathrm{s}^2 \mathrm{m}\))
- \({\tau }\)
Shear stress (\(\mathrm{kg}/\mathrm{s}^2 \mathrm{m}\))
- \({\mathbf {I}}\)
Identity matrix
- \({\mathbf {K}}\)
Intrinsic permeability (\({\mathrm{m}^2}\))
- \(\varrho \)
Mass density (\(\mathrm{kg}/\mathrm{m}^3\))
- \(\varrho _{\text {mol}}\)
Molar density (\(\mathrm{mol}/\mathrm{m}^3\))
- \(\varrho _{\text {s}}\)
Mass density of the solid material (\(\mathrm{kg}/\mathrm{m}^3\))
- \(\varvec{{{g}}}\)
Gravity vector (\(\mathrm{m}/\mathrm{s}^2\))
- \(\varvec{{{n}}}\)
Interface-normal vector
- \(\varvec{{{t}}}\)
Interface-tangential vector
- \(\varvec{{{v}}}\)
Velocity (\(\mathrm{m}/\mathrm{s}\))
- \(c_{\text {f}}\)
Skin friction coefficient
- \(c_{\text {p}}\)
Specific isobaric heat capacity (\(\mathrm{J}/\text {kg K}\))
- \(c_{\text {s}}\)
Specific heat capacity of the solid material (\(\mathrm{J}/\text {kg K}\))
- D
Molecular diffusion coefficient (\(\mathrm{m}^2/\mathrm{s}\))
- \(d_{\text {hy}}\)
Hydraulic radius (m)
- \(D_{\text {pm}}\)
Porous-medium diffusion coefficient (\(\mathrm{m}^2/\mathrm{s}\))
- \(D_{\text {t}}\)
Eddy diffusivity (\(\mathrm{m}^2/\mathrm{s}\))
- f
Darcy friction factor
- h
Discretization width (mm)
- h
Specific enthalpy (\(\mathrm{J}/\mathrm{kg}\))
- \(k_{\text {r}}\)
Relative permeability
- \(k_{\text {s}}\)
Sand-grain roughness (m)
- \(k_{\text {s}}^+\)
Equivalent sand-grain roughness
- \(l_\text {mix}\)
Mixing length (m)
- M
Molar mass (\(\mathrm{kg}/\mathrm{mol}\))
- n
Number of cells (in x- or y-direction)
- \(n_{\text {vg}}\)
Van Genuchten parameter
- p
Phase pressure (\(\mathrm{kg}/\mathrm{s}^2\mathrm{m}\))
- \(p_{\text {c}}\)
Capillary pressure (\(\mathrm{kg}/\mathrm{s}^2 \mathrm{m}\))
- \(Pr_{\text {t}}\)
Turbulent Prandtl number
- Re
Reynolds number (length (x) or diameter (d) based)
- S
Saturation
- \(Sc_{\text {t}}\)
Turbulent Schmidt number
- T
Temperature (K)
- u
Velocity component in main flow direction (\(\mathrm{m}/\mathrm{s}\))
- \(u^*\)
Wall friction velocity (\(\mathrm{m}/\mathrm{s}\))
- \(u^{\text {e}}\)
Specific internal energy (\(\mathrm{J}/\mathrm{kg}\))
- X
Mass fraction
- x
Mole fraction
- y
Wall distance/ y-coordinate (m)
- \(y^+\)
Dimensionless wall distance
- BL
Boundary layer
- ff
Free flow
- if
Interface
- pm
Porous medium
1 Introduction
A better understanding of the interactions between free flow and flow in porous media is critical for a variety of applications in different fields, like medical science (Chauhan et al. 2011), building physics (Defraeye et al. 2010), aerospace engineering (Dahmen et al. 2014), food processing (Verboven et al. 2006), and agriculture (Jambhekar et al. 2015; Fujimaki et al. 2006).
In many of these applications, the processes in the two domains are strongly coupled. Therefore, different modeling strategies for these problems exist. The most detailed, but also very time-consuming, method is a direct numerical simulation (DNS) of the entire problem. This one-domain approach is used, e.g., in Krafczyk et al. (2015), Hahn et al. (2002) and Breugem and Boersma (2005). In contrast to these one-domain models, in two-domain models a sharp interface separates the free-flow and the porous-medium domain and two different sets of equations are used to describe the processes in the two domains. Considering two different domains is desirable from a physical point of view. Because the free-flow processes act on smaller spatial and temporal scales than the porous-medium processes, the two-domain approach allows for the detailed modeling of the free flow while still applying simplifying assumptions to the porous medium (Dahmen et al. 2014; Mosthaf et al. 2014; Defraeye 2011). These different temporal and spatial scales also motivate different numerical treatments of the subdomains (Rybak et al. 2015; Arbogast et al. 2007). The effects of coupling turbulent free-flow models to Richards or Darcy–Forchheimer models have been both studied theoretically and applied to heat transfer and drying problems, see Defraeye et al. (2010), Dahmen et al. (2014), Lemos (2009) and Pedras and Lemos (2001).
It is critical to find a suitable coupling concept between the porous-medium and free-flow domains that is capable of properly describing the behavior at the interface. One option is to allow nonzero tangential velocities directly at the interface by replacing the no-slip boundary condition with a slip boundary condition, e.g., Beavers and Joseph (1967), Saffman (1971), Sahraoui and Kaviany (1992), and Nield (2009). However, these concepts neither account for turbulence, roughness, or saturation effects. The effects of roughness resulting from discrete obstacles on evaporation have been investigated previously, e.g., in Haghighi and Or (2015) and Sugita and Kishii (2002). Further, porous-medium surfaces are never perfectly smooth and thus the influence of roughness resulting from the matrix material needs to be analyzed. For heat transfer problems, this has been done by Kuznetsov and Becker (2004) and Kuznetsov (2004).
The coupling between the free-flow and porous-medium flow is extremely relevant to evaporation processes from bare soil surfaces. Evaporation from soil surfaces is a vital research subject in the past few years and has been investigated at the pore scale, e.g., (Shahraeeni et al. 2012; Assouline et al. 2010; Yiotis et al. 2007; Laurindo and Prat 1998; Suzuki and Maeda 1968), at the REV scale, e.g., (Trautz et al. 2015; Zhang et al. 2015; Mosthaf et al. 2014 and Schneider-Zapp et al. 2010), and at larger scales, e.g., (Vanderborght et al. 2010; Shukla and Mintz 1982 and Penman 1948).
Evaporation from bare soil surfaces is influenced by different processes and properties in both domains, as shown in Fig. 1. Although all of the processes shown in Fig. 1 are important, this study focuses on the influence of a turbulent free flow over a rough and permeable surface on the exchange processes. As mentioned above, aspects of roughness and turbulence have been partially investigated in other fields. However, previous studies do not combine models for turbulence and roughness to analyze the effects on coupled processes for all: mass, momentum, and energy transfer in both domains.
In this study, the coupled processes are considered by analyzing evaporation from a bare soil surface. During this evaporation process, two different stages are discerned (Lehmann et al. 2008; van Brakel 1980). The stage-I period is characterized by higher evaporation rates, constrained by the atmospheric demand. The stage-II period, in contrast, is characterized by a falling rate, followed by a constant rate period and limited by diffusive transport through the unsaturated soil (Shokri and Or 2011).
The objectives of this work are (i) to present a numerical model concept that considers turbulence and roughness and can be applied to various coupled porous-medium/free-flow applications, (ii) to analyze the sensitivity of parameters and processes that influence evaporation from rough and permeable surfaces induced by an adjacent turbulent free flow, and (iii) to demonstrate the applicability of the modeling approach by comparing simulation results to existing bench-scale evaporation experiments (Davarzani et al. 2014).
2 Models
In the following section, the models for the porous medium, the free flow, and the interface are presented in detail.
2.1 Porous Medium
2.2 Free Flow
The Navier–Stokes equations describe both laminar and turbulent free flow. As already discussed, simulating free flow and turbulence using DNS is theoretically possible, but computationally expensive. Therefore, turbulence is normally parametrized. In addition to the Navier–Stokes equations, the Reynolds-averaged Navier–Stokes (RANS) equations used for turbulence modeling are introduced. The following assumptions are made with respect to the free-flow models used in this work: (i) one fluid phase, consisting of two components, (ii) Newtonian fluid without dilatation, (iii) no gravitational forces, and (iv) Fickian diffusion.
2.2.1 Navier–Stokes
2.2.2 Reynolds-Averaged Navier–Stokes
Turbulence can be modeled by using suitable closure concepts for the turbulent quantities resulting from the averaging process. General assumptions for the RANS equations using an eddy viscosity parametrization are: (i) Flow is incompressible to turbulent pressure fluctuations (which is valid up to a Mach number of 0.3), (ii) isotropic turbulence, and (iii) the Boussinesq assumption which states that the turbulent stresses can be modeled like viscous stresses.
We acknowledge that the algebraic turbulence models are only suitable for simple geometries and more comprehensive models are available in the literature, e.g., Wilcox (2006). However, here the focus is on the description of exchange processes for simple geometries, and therefore, algebraic turbulence models are appropriate. In this work, the following eddy viscosity models are used: Prandtl mixing length, the Hanna–van Driest modification (van Driest 1956; Hanna et al. 1981), and the Baldwin–Lomax model (Baldwin and Lomax 1978).
2.3 Interface Conditions
Coupling conditions are needed at the interface between the free-flow and the porous-medium region, because different model concepts are used in the two subdomains. The interface conditions are based on those presented in Mosthaf et al. (2014). Here, two extensions will be made to this approach.
The first extension includes the eddy viscosity, eddy diffusivity, and eddy conductivity into the interface conditions for the sake of a consistent model concept. The second modification pertains to the energy balance and includes the enthalpy transported by the diffusive component fluxes in the free flow (\(\bar{h}_{{\text {g}}}^\kappa \bar{\varvec{{{j}}}}^\kappa _{{\text {g,ff,t,diff}}}\)).
2.4 Roughness Parametrization
Sand-grain roughness may affect the boundary layer development which plays an important role for the diffusion-dominated transport near the interface. This section presents two concepts on how the sand-grain roughness of the porous medium can be included in coupled models. Both concepts were originally derived for roughness elements on an impermeable plate, and for both concepts, the determination of a characteristic sand-grain roughness length \(k_{{\text {s}}}\) is critical. A correlation with the sand-grain diameter is proposed in Schlichting and Gersten (1997) for roughness elements on an impermeable plate. Kuznetsov and Becker (2004) proposed a model which relates the sand-grain roughness to porous-medium properties.
2.4.1 Eddy Viscosity Models
2.4.2 Boundary Layer Models
Summary of balance equations, primary variables, and auxiliary equations
Domain | Balance eq. | Unknowns | RANS eq. | BL model eq. | Auxiliary eq. |
---|---|---|---|---|---|
FF | Mass | \(\bar{p}_{\text {g}}\) | (11) | (5) | |
Momentum | \(\varvec{{{\bar{v}}}}_{\text {g}}\) | (12) | (6) | RANS: \(\nu _{\text {g,t}}\) (e.g., 14) | |
Component | \(\bar{X}^{\text {w}}_{\text {g}}\) | (16) | (8) | RANS: \(D_{\text {g,t}}\) (e.g., 15) | |
Energy | \(\bar{T}\) | (19) | (10) | RANS: \(\lambda _{\text {g,t}}\) (e.g., 18) | |
PM | Momentum | \(p_{{\text {g}}}\) | (1) | \(p_{{\text {c}}}-S_{\text {l}}\), \(k_{{\text {r,}}\alpha }-S_{\text {l}}\): linearized van Genuchten (1980) | |
Component | \(S_{\text {l}}\) or \(X^{{\text {w}}}_{{\text {g}}}\) | (2) | \(X^{{\text {w,sat}}}_{{\text {g}}}\): Raoult’s law,\(D^\kappa _{\alpha ,{{\text {pm}}}}\): (Millington and Quirk 1961) | ||
Energy | T | (4) | \(\lambda _{{\text {eff,pm}}}\): (Johansen 1975) | ||
IF | Mass | (21) | |||
Momentum | \(u_{{\text {g,slip}}}\): (Beavers and Joseph 1967; Saffman 1971) | ||||
Component | BL: (31) | ||||
Energy |
2.5 Discretization and Numerical Framework
The presented model concept and its equations (Table 1) are implemented in the open-source simulator DuMu\(^\text {x}\) (Flemisch et al. 2011; Schwenck et al. 2015), which is based on the numerical toolbox DUNE (Bastian et al. 2008b, a). The code used in this paper is available on request to the corresponding author. The set of partial differential equations is discretized using the box method (Huber and Helmig 2000). More details on the implementation of the coupling concept can be found in Baber et al. (2012), whereas Fetzer (2012) provides more information on the implementation of the turbulence models. The monolithic system is solved by a fully implicit scheme using SuperLU (Demmel et al. 1999).
3 Results and Discussion
In this section, the experimental setup is introduced, followed by a presentation of the numerical setup. Afterward, simulation results are discussed, starting with different model setups and closing with a sensitivity analysis of the turbulence models and interface parameters.
3.1 Experiments
Summary of the sensors used for comparison in this work
Sensor | Type | x-location | y-location |
---|---|---|---|
PM3 | T,\(S_{\text {l}}\) | \(12.5\,{\mathrm{cm}}\) | \(2.5\,{\mathrm{cm}}\) below surface |
PM8 | T,\(S_{\text {l}}\) | \(12.5\,{\mathrm{cm}}\) | \(7.5\,{\mathrm{cm}}\) below surface |
Soil properties
Parameter | Value | Parameter | Value |
---|---|---|---|
K\(\left[ {\mathrm{m}}^2 \right] \) | \(1.08 \times 10^{-10}\) | \(\phi \)\(\left[ {-} \right] \) | 0.334 |
\(S_{{\text {l,r}}}\)\(\left[ {-} \right] \) | 0.08383 | \(S_{{\text {g,r}}}\)\(\left[ {-} \right] \) | 0.01 |
\(\alpha _{{\text {vg}}}\)\(\left[ 1/\mathrm{Pa}\right] \) | \(5.8 \times 10^{-4}\) | \(n_{{\text {vg}}}\)\(\left[ {-} \right] \) | 17.8 |
\(\lambda _{{\text {s}}}\)\(\left[ \mathrm W/(\mathrm{m}\,\mathrm{K}) \right] \) | 5.9 | \(\alpha _{{\text {BJ}}}\)\(\left[ {-} \right] \) | 1.0 |
Initial and boundary condition values for the individual experiments and simulations
Variable | \(0.55\,\mathrm{m}/\mathrm{s}\) | \(1.22\,\mathrm{m}/\mathrm{s}\) | \(3.65\,\mathrm{m}/\mathrm{s}\) | |
---|---|---|---|---|
FF | \(\bar{u}_{{\text {g}}}\)\(\left[ \mathrm{m}/\mathrm{s}\right] \) | 0.552 | 1.224 | 3.642 |
\(\bar{p}_{{\text {g}}}\)\(\left[ {\mathrm{Pa}} \right] \) | \(1 \times 10^{5}\) | \(1 \times 10^{5}\) | \(1 \times 10^{5}\) | |
\(\bar{X}^{{\text {w}}}_{{\text {g}}}\)\(\left[ {-} \right] \) | 0.0038 | 0.0032 | 0.0061 | |
\(\bar{T}\)\(\left[ \mathrm{K} \right] \) | 314.1 | 314.2 | 320.6 | |
PM | \(S_{{\text {l}}}\)\(\left[ {-} \right] \) | 0.98 | ||
\(p_{{\text {g}}}\)\(\left[ {\mathrm{Pa}} \right] \) | \(1 \times 10^{5}\) | |||
\(\bar{X}^{{\text {w}}}_{{\text {g}}}\)\(\left[ {-} \right] \) | \(\bar{X}^{{\text {w,sat}}}_{{\text {g}}} (p_{{\text {g}}},T)\) | |||
T\(\left[ \mathrm{K} \right] \) | 302.05 | 300.85 | 296.15 |
3.2 Reference Model Setup
The reference cases use the RANS equations (Eqs. 11–19) and 2-D model setup with the initial/boundary conditions described in Table 4 and Fig. 8. The reference discretization uses \(n_{\text {x}}=100\) and \(n_{\text {y}}=50\) cells, see Table 5 for more details.
The basic assumption, for the numerical modeling presented here, is to consider the experiment as a 2-D system. In reality, the flow is also influenced by the side walls and not only by the porous-medium surface. The hypothesis is that the exchange is driven by diffusion in the free flow near the porous-medium surface and is therefore mainly affected by the viscous sublayer evolving above the porous medium (e.g., Bird et al. 2007; Haghighi and Or 2013).
To reduce computational costs, only the lower half of the free-flow channel in the section downstream of the heater is modeled (see Figs. 5 and 8). Velocity, temperature, and humidity values are assumed to be constant over height. For a better definition of the setup, it would be important to have additional experimental measurements at the inlet position (e.g., vertical profiles of these values). For the reference cases, the surface of the porous medium is assumed to be smooth. This assumption will be loosened and discussed in the last section, in which the surface roughness parametrizations are analyzed. Measurements show that the soil remains saturated below 25 cm in the considered time frame. Therefore, only the upper 25 cm of the porous medium are modeled. No-flow boundary conditions are imposed at the porous-medium boundaries. The evaporation rates are calculated by evaluating the temporal derivative in the porous-medium domain.
Grid specifications: number of cells n, characteristic discretization width h, and relative \(L^2\) error of the evaporation rates for different grids
\(n_{\text {x}}\) | \(h_{\text {x}}\) | \(L^2\) err | \(n_{\text {y}}\) | \(n^{\text {ff}}_{\text {y}}\) | \(n^{\text {pm}}_{\text {y}}\) | \(h^{\text {min}}_{\text {y}}\) | \(L^2\) err |
---|---|---|---|---|---|---|---|
\([-]\) | \([{\mathrm{mm}}]\) | \([-]\) | \([-]\) | \([-]\) | \([-]\) | \([{\mathrm{mm}}]\) | \([-]\) |
50 | 25 | 0.072 | 30 | 13 | 17 | 2.66 | 0.110 |
75 | 16 | 0.041 | 40 | 18 | 22 | 1.01 | 0.061 |
100 | 12.5 | 0.021 | 50 | 23 | 27 | 0.40 | 0.029 |
125 | 10 | 0.008 | 60 | 28 | 32 | 0.16 | 0.013 |
150 | 8.3 | 0.000 | 70 | 33 | 37 | 0.06 | 0.000 |
Choice of Numerical Model Setup: To check the applicability of the above-mentioned simplifications and to assess the sensitivity of the system, three different setups are compared to the chosen reference case (see Fig. 8). The first considers a closed top (pipe) instead of only the lower half of the domain. The other setups are used to investigate the influence of the run length on the boundary layer development and its thickness. The evaporation rates for the setups are shown in Fig. 9. For the short setup, the evaporation rates are higher, because the boundary layer is not developed when passing over the porous medium. The other setups are more comparable in terms of evaporation rates; the reference and the pipe setup produce almost identical evaporation rates. The reference setup is selected for further study because of its numerical stability.
The resolution in x-direction affects the evaporation rate value during stage-I . This can be attributed to the fact that the grid points at the upper corner points of the porous medium are not coupled to the free flow and thus cannot contribute to the evaporation. For the y-direction, a lower resolution leads to a longer stage-I evaporation. In this case, porous-medium cells closer to the surface have larger volumes and thus contain water for a longer time.
3.3 Reference Cases
\(\bar{u}_{\text {g}}=0.55\)\(\mathrm{m}/\mathrm{s}\): For the lowest wind velocity, it can already be seen that the stage-I evaporation rates modeled using laminar flow are smaller than those including turbulence, as shown in Fig. 11a. In later stage-II , the evaporation rates for laminar and turbulent cases converge. This agrees with the fact that stage-II evaporation rates are limited by porous-medium properties rather than by atmospheric conditions. Especially in stage-II , which approximately starts after \(\sim \)3 days, simulation and experimental results fit well; as shown in Fig. 11b, the gradients of the water mass loss curves are very similar.
\(\bar{u}_{{\text {g}}}=1.22\)\(\mathrm{m}/\mathrm{s}\): Fig. 12a shows, as expected, that the difference between laminar and turbulent modeling becomes more significant at higher wind velocities. In this setup, the effect of the measured values, imposed as boundary conditions, is more pronounced and the fluctuations are less frequent with higher amplitudes. The fluctuations in the early stage-I evaporation rate can qualitatively be reproduced. Again, measured and simulated stage-I evaporation rates are in quite good agreement. For the simulations, the transition to stage-II is much sharper than in the experiment, because the REV concept cannot reproduce the pore-by-pore drying of the surface. Especially for larger wind velocities or larger distance between the evaporating pores, the evaporation rate may already drop during stage-I , see Shahraeeni et al. (2012). This behavior is observed here. The stage-II evaporation rates can be matched in a time-averaged sense. As before, varying the free-flow boundary conditions does not affect simulated stage-II evaporation rates. Therefore, other factors (e.g., errors in measurement, wrong averaging interval, non-homogeneous soil properties, heat transfer through the side walls of the soil box) have to be responsible for the measured fluctuations.
In the cumulative mass loss plot shown in Fig. 12b, the measured variations in the evaporation curves are visible as small kinks of the curve. From this plot, it can be seen that the transition to stage-II is predicted too early. At the end of the simulation, the predicted evaporation rate is underestimated by about 15 %. Although the laminar case strongly underestimates the stage-I evaporation, its final prediction of the water mass loss is almost comparable to the prediction of the turbulent case (with a difference of about 4 %).
\(\bar{u}_{\text {g}}=3.65\)\(\mathrm{m}/\mathrm{s}\): For the highest wind velocity, the difference between the laminar and the turbulent case becomes most significant, reaching a difference of almost \(5\,{\mathrm{mm}}/\mathrm{d}\) during stage-I evaporation, as shown in Fig. 14a. The influence of measured free-flow properties on the simulated evaporation rate can hardly be evaluated, due to a rapidly decreasing stage-I evaporation rate and a very early drying out of the porous medium.
Figure 14b shows the cumulative mass loss with a different behavior than in the previous plots. First, higher evaporation rates lead to steeper gradients in the cumulative mass loss curves. Because of the steeper gradients, early stage-I evaporation rates seem to be approximated as good as for smaller wind velocity cases. However, this is difficult to deduce only by the evaporation rate plot (Fig. 14a). Second, simulated stage-II evaporation rates are higher than measured values. This, in contrast, can hardly be seen in the evaporation rate plot. It has to be remarked that the measured, porous medium controled, stage-II evaporation rates are much lower than for the previous velocities. But as the porous medium was the same for all experiments, the measured stage-II evaporation rates for the different velocities should be more or less equivalent (as it is for the simulations). Further, negative evaporation rates are observed for stage-II . This can be attributed to the averaging interval and experimental errors (e.g., scale resolution and sensitivity) as negative rates are observed in the original cumulative mass loss data set.
3.4 Porous-Medium Quantities
Temperature: The evolution of the porous-medium temperature for the two sensor locations is shown in Fig. 15a. Measurements are compared to the reference case with an isolated porous-medium sand box and a case in which the temperature is kept constant at the porous-medium boundaries. For the case of an isolated box, the simulated and measured temperature evolutions are quite different. This is due to the perfect isolation which means that there is no opportunity for the porous medium to compensate for the energy loss by evaporation, resulting in very low temperatures at the end of stage-I . After the porous medium is dried out, it is continuously supplied with energy from the free flow and finally reaches the free-flow temperature. This behavior cannot be seen in the measurements.
For the second setup with a constant temperature at the porous-medium boundaries, it is seen that (i) the temperature does not constantly decrease during stage-I , (ii) the porous-medium temperature is relatively more affected by the measured free-flow boundary conditions and the resulting fluctuations qualitatively match the observed behavior, and (iii) the porous-medium temperature does not approach the free-flow temperature toward the end of the simulation.
Of course, these two concepts are the extreme cases for the porous-medium boundary conditions. The prediction of the temperature evolution inside the porous medium is better when using a constant temperature around the porous medium. But this case drastically overestimates the stage-I evaporation rates compared to measurements; here the isolated case fits better (Fig. 16). This analysis shows that the heat loss has a strong influence on the temperature distribution. For future experiments and simulations, it is necessary to find a better way to quantify and account for these losses.
3.5 Turbulence Models
The evaluation of the influence of turbulence and turbulence models is structured in two parts: First, the influence of the eddy viscosity model is analyzed, and second, the impacts of eddy diffusivity and eddy conductivity models are investigated.
Eddy Diffusivity and Eddy Conductivity Models: Compared to the eddy viscosity models, the influence of the eddy diffusivity and eddy conductivity models is small, as shown in Fig. 18. The same models for eddy diffusivity and eddy conductivity are used on top of the Baldwin–Lomax model for the eddy viscosity. Using different turbulent Schmidt and Prandtl numbers (\(Sc_{{\text {t}}} = 0.63\), \(Pr_{{\text {t}}} = 0.85\)), instead of unity as for the Reynolds analogy, leads to the expected higher evaporation rates. Deissler’s model (Deissler 1954), which has the advantage of being independent of the eddy viscosity model, the Hanna–van Driest model, and the Reynolds analogy give almost the same results.
Interface slip velocities taken at \(x=1\,\mathrm{m}\) and \(t=8\,\mathrm{d}\), for different free-flow velocities and different \(\alpha _{{\text {BJ}}}\) values
Conditions | \(\alpha _{{\text {BJ}}}\) value | \(\bar{u}_{{\text {g,slip}}}\)\(\left[ \mathrm{m}/\mathrm{s} \right] \) | |
---|---|---|---|
\(\bar{u}_{{\text {g}}}=1.22\, \mathrm{m}/\mathrm{s}\) | \(\bar{u}_{{\text {g}}}=3.65\,\mathrm{m}/\mathrm{s}\) | ||
Laminar | 0.01 | 0.109 | 0.562 |
1 | 0.00065 | 0.0049 | |
100 | \(6.4 \times 10^{-6}\) | \(4.9 \times 10^{-5}\) | |
Turbulent | 0.01 | 0.202 | 1.027 |
1 | 0.0025 | 0.0193 | |
100 | \(2.5 \times 10^{-5}\) | \(1.9 \times 10^{-4}\) |
3.6 Interface Parameters
This section focuses on the influence of properties of the porous-medium/free-flow interface. Here the effect of the Beavers–Joseph coefficient and of the sand-grain roughness is studied. As explained above, different formulations to link the sand-grain roughness to soil properties exist, e.g., to relate the sand-grain roughness with the median grain size diameter or to use the Kozeny–Carman equation, see Kuznetsov and Becker (2004). Both values (\(d_{50}=k_{{\text {s}}}=0.52\,{\mathrm{mm}}\) and \(k_{{\text {s}}}=0.24\,{\mathrm{mm}}\)) are inside the range of values considered in this study. To show the influence of this parameter, the sand-grain roughness is varied over three orders of magnitude to numerically investigate its influence on the evaporation rates.
Beavers–Joseph Coefficient: Different studies pertaining to the sensitivity of evaporation rates on the Beavers–Joseph coefficient \(\alpha _{{\text {BJ}}}\) have been carried out for Stokes flow or laminar flow, e.g., Baber et al. (2012) and Davarzani et al. (2014). All conclude that the \(\alpha _{{\text {BJ}}}\) coefficient has little influence on the evaporation rate. However, in Fig. 19 an influence of the Beavers–Joseph coefficient on the evaporation rate is observed. The different observations may be explained by 0.1 as the lowest \(\alpha _{{\text {BJ}}}\) value in Baber et al. (2012) or by the plot type in Davarzani et al. (2014), because cumulative mass loss plots shadow effects occurring during stage-I . For turbulent conditions, the influence on the evaporation rate is small compared to the magnitude of variation in \(\alpha _{{\text {BJ}}}\). Nevertheless, the influence on the slip velocity is more noticeable, see Table 6. For high \(\alpha _{{\text {BJ}}}\) values, the influence on the slip velocity decreases as the no-slip condition is approached. For low \(\alpha _{{\text {BJ}}}\) values, the resulting slip velocities for laminar and turbulent models are both relatively high. The larger influence of \(\alpha _{{\text {BJ}}}\) on the evaporation rate for the laminar case is explained by a relatively stronger increase in the near-interface velocities and gradients. Further, in the laminar case, the velocity profile is affected over a larger height and the relative increase in velocity is higher compared to the turbulent case.
For higher velocities, the critical roughness length, needed to see a response in the evaporation rates, becomes smaller. For \(\bar{u}_{{\text {g}}}=3.65\,{\mathrm{m}}/{\mathrm{s}}\) a value of \(k_{{\text {s}}}=1\,{\mathrm{mm}}\) is sufficient to increase the rates.
For both velocities, the results are qualitatively as expected: Larger roughness lengths or higher velocities lead to more turbulent transport near the soil surface and hence increase the exchange fluxes between the two domains. The question how the results quantitatively correspond to measured data for different kind of roughness lengths and types cannot be answered here and requires additional experiments.
The application of these boundary layer models is only justified as long as a viscous sublayer is present. For aerodynamically rough surfaces, this is not the case. Table 7 shows that \(k_{{\text {s}}}=10\,{\mathrm{mm}}\) corresponds to the fully rough case for \(\bar{u}_{{\text {g}}}=1.22\,\mathrm{m}/\mathrm{s}\).
The two boundary layer models after Colebrook and White (CW, Eq. 35) and Truckenbrodt (Tr, Eq. 34) predict higher evaporation rates than the EV model. Nevertheless, both models produce quite different results. Although the CW model was developed to capture the entire range from smooth to aerodynamically rough surfaces, the evaporation rate by the CW model is almost 50 % higher than the rate simulated with the EV model. In contrast to CW model, the Tr model is restricted to aerodynamically rough surfaces. For the qualitative analysis performed here, it was assumed that the fully rough skin fiction value is an acceptable approximation for aerodynamically smooth surfaces. This is questioned by the difference in evaporation rate for the two roughness lengths.
4 Conclusion
In Sect. 2, a model concept for coupling turbulent free flow, using the RANS equations, and porous-medium flow, using extended Darcy’s law is presented. The results in Sect. 3 indicate that the effect of turbulence on the exchange behavior may be decisive, especially during stage-I evaporation. Therefore, simulation concepts for evaporation from bare soil surfaces have to properly account for turbulence effects.
Results show that a considerable amount of uncertainty in the simulated evaporation rate originates from the chosen model setup and the boundary conditions in both the free- and the porous-medium flow regions. This indicates that detailed measurements and well-defined experimental setups are required for bridging the gap between experiments and simulations. Possible sources of error in the presented numerical simulations are (i) the 2-D setup and parametrization of turbulence, (ii) the assumption of local thermodynamic equilibrium inside the porous medium, and (iii) the assumption of a constant inflow profile or effects resulting from the neglected heater section on the free flow.
Generally, the predicted stage-I evaporation rates are in good agreement with the experimental data. Fluctuations in the evaporation rate are partly reproduced by using measured free-flow boundary conditions. Also stage-II evaporation rates agree very well with the measured evaporation rates, except in the case of \(\bar{u}_{{\text {g}}}=3.65\,\mathrm{m}/\mathrm{s}\); here, the discrepancy is assumed to arise from the measurements.
However, the model is not able to predict the shape and time of the transition from stage-I to stage-II evaporation. The simulated transition between stage-I and stage-II is sharper than the measured transition in the experiments. Further, it was not possible to predict the cumulative evaporated water mass at the time the transition occurs. With respect to porous-medium saturation, it is observed that the extended multiphase Darcy’s law is not able to reproduce the measured saturation profiles. Similar to Davarzani et al. (2014) numerical and experimental saturations do not match well a few centimeters below the soil surface.
Differences in evaporation rate due to different turbulence models are rather small. Only the Prandtl mixing length model does not consider a dampening of the eddy viscosity toward the wall; therefore, the evaporation rates are higher, because the Reynolds analogy is used for the eddy diffusivity and conductivity. Different eddy diffusivity and eddy conductivity models have a small influence on the exchanged mass fluxes.
The Beavers–Joseph coefficient does affect slip velocities, but the effect on evaporation is small for the analyzed scale. For the same wind velocity, when using a laminar concept, the effect on the evaporation rates and near surface velocities is larger than when modeling the turbulence. Nevertheless, low \(\alpha _{{\text {BJ}}}\) values are needed to see any effect on the evaporation rates at all.
Including a roughness parametrization fulfills the expected qualitative behavior; higher surface roughness leads to higher evaporation rates. In contrast to the eddy viscosity model for roughness, the roughness parametrizations with boundary layer models introduce more parameters and thus more uncertainty. However, effects of the sand-grain roughness are only visible for high velocities or large grain sizes (e.g., gravel). A detailed quantitative comparison of the effect of roughness in models and experiments is still necessary.
Notes
Acknowledgments
This work was supported by the German Research Foundation (DFG). Some of the authors are members of the International Research Training Group NUPUS funded by the German Research Foundation (DFG) and Netherlands Organization for Scientific Research (NWO). We thank the DFG for their support. Furthermore, we thank Hossein Davarzani and Ryan Tolene for their contributions to the experimental data and Bernd Flemisch and Christoph Grüninger for the helpful discussions and input.
References
- Arbogast, T., Pencheva, G., Wheeler, M.F., Yotov, I.: A multiscale mortar mixed finite element method. Multiscale Model. Simul. 6(1), 319–346 (2007). doi:10.1137/060662587 CrossRefGoogle Scholar
- Assouline, S.: Modeling the relationship between soil bulk density and the water retention curve. Vadose Zone J. 5(2), 554–563 (2006). doi:10.2136/vzj2005.0083 CrossRefGoogle Scholar
- Assouline, S., Narkis, K., Or, D.: Evaporation from partially covered water surfaces. Water Resour. Res. 46(W10), 539 (2010). doi:10.1029/2010WR009121 Google Scholar
- Baber, K., Mosthaf, K., Flemisch, B., Helmig, R., Müthing, S., Wohlmuth, B.: Numerical scheme for coupling two-phase compositional porous-media flow and one-phase compositional free flow. IMA J. Appl. Math. 77(6), 887–909 (2012). doi:10.1093/imamat/hxs048 CrossRefGoogle Scholar
- Baldwin, B.S., Lomax, H.: Thin layer approximation and algebraic model for separated turbulent flows. AIAA J. 78–257, 1–9 (1978). doi:10.2514/6.1978-257 Google Scholar
- Bastian, P., Blatt, M., Dedner, A., Engwer, C., Klöfkorn, R., Kornhuber, R., Ohlberger, M., Sander, O.: A generic grid interface for parallel and adaptive scientific computing. Part II: implementation and tests in DUNE. Computing 82(2–3), 121–138 (2008a). doi:10.1007/s00607-008-0004-9 CrossRefGoogle Scholar
- Bastian, P., Blatt, M., Dedner, A., Engwer, C., Klöfkorn, R., Ohlberger, M., Sander, O.: A generic grid interface for parallel and adaptive scientific computing. Part I: abstract framework. Computing 82(2–3), 103–119 (2008b). doi:10.1007/s00607-008-0003-x CrossRefGoogle Scholar
- Beavers, G.S., Joseph, D.D.: Boundary conditions at a naturally permeable wall. J. Fluid Mech. 30(1), 197–207 (1967). doi:10.1017/S0022112067001375 CrossRefGoogle Scholar
- Bird, R.B., Stewart, W.E., Lightfoot, E.N.: Transport Phenomena, 2nd edn. Wiley, New York (2007)Google Scholar
- Breugem, W.P., Boersma, B.J.: Direct numerical simulations of turbulent flow over a permeable wall using a direct and a continuum approach. Phys. Fluids 17(2), 15 (2005). doi:10.1063/1.1835771 CrossRefGoogle Scholar
- Cebeci, T.: Calculation of incompressible rough-wall boundary layer flows. AIAA J. 16(7), 730–735 (1978). doi:10.2514/3.7571 CrossRefGoogle Scholar
- Chauhan, V.P., Stylianopoulos, T., Boucher, Y., Jain, R.K.: Delivery of molecular and nanoscale medicine to tumors: transport barriers and strategies. Ann. Rev. Chem. Biomol. Eng. 2, 281–298 (2011). doi:10.1146/annurev-chembioeng-061010-114300 CrossRefGoogle Scholar
- Ciocca, F., Lunati, I., Parlange, M.B.: Effects of the water retention curve on evaporation from arid soils. Geophys. Res. Lett. 41, 3110–3116 (2014). doi:10.1002/2014GL059827 CrossRefGoogle Scholar
- Colebrook, C.F.: Turbulent flow in pipes, with particular reference to the transition region between smooth and rough pipe laws. J. Inst. Civ. Eng. 11, 133–156 (1939). doi:10.1680/ijoti.1939.13150 CrossRefGoogle Scholar
- Dahmen, W., Gotzen, T., Müller, S., Rom, M.: Numerical simulation of transpiration cooling through porous material. Int. J. Numer. Meth. Fluids 76(6), 331–365 (2014). doi:10.1002/fld.3935 CrossRefGoogle Scholar
- Davarzani, H., Smits, K., Tolene, R.M., Illangasekare, T.: Study of the effect of wind speed on evaporation from soil through integrated modeling of the atmospheric boundary layer and shallow subsurface. Water Resour. Res. 50, 1–20 (2014). doi:10.1002/2013WR013952 CrossRefGoogle Scholar
- de Lemos, M.J.S.: Turbulent flow around fluid–porous interfaces computed with a diffusion-jump model for \(k\) and \(\varepsilon \) transport equations. Transp. Porous Media 78, 331–346 (2009). doi:10.1007/s11242-009-9379-0 CrossRefGoogle Scholar
- Defraeye T (2011) Convective heat and mass transfer at exterior building surfaces. PhD thesis, Katholieke Universiteit LeuvenGoogle Scholar
- Defraeye, T., Blocken, B., Carmeliet, J.: CFD analysis of convective heat transfer at the surfaces of a cube immersed in a turbulent boundary layer. Int. J. Heat Mass Transf. 53(1–3), 297–308 (2010). doi:10.1016/j.ijheatmasstransfer.2009.09.029 CrossRefGoogle Scholar
- Deissler, R.G.: Analysis of turbulent heat transfer, mass transfer, and friction in smooth tubes at high Prandtl and Schmidt numbers. NACA Rep. 1210, 69–82 (1954)Google Scholar
- Demmel, J.W., Eisenstat, S.C., Gilbert, J.R., Li, X.S., Liu, J.W.H.: A supernodal approach to sparse partial pivoting. SIAM J. Matrix Anal. Appl. 20(3), 720–755 (1999). doi:10.1137/S0895479895291765 CrossRefGoogle Scholar
- Discacciati, M., Quarteroni, A.: Navier–Stokes/Darcy coupling: modeling, analysis, and numerical approximation. Revista Matemática Complutense 22(2), 315–426 (2009)CrossRefGoogle Scholar
- Fetzer, T.: Numerical analysis of the influence of turbulence on exchange processes between porous-medium and free flow. Diploma thesis, University of Stuttgart (2012)Google Scholar
- Flemisch, B., Darcis, M., Erbertseder, K., Faigle, B., Lauser, A., Mosthaf, K., Müthing, S., Nuske, P., Tatomir, A., Wolff, M., Helmig, R.: DuMuX: DUNE for Multi-\(\{\)Phase, Component, Scale, Physics, \(\ldots \) \(\}\) Flow and Transport in Porous Media. Adv. Water Resour. 34(9), 1102–1112 (2011). doi:10.1016/j.advwatres.2011.03.007 CrossRefGoogle Scholar
- Fujimaki, H., Shimano, T., Inoue, M., Nakane, K.: Effect of a salt crust on evaporation from a bare saline soil. Vadose Zone J. 5(4), 1246–1256 (2006). doi:10.2136/vzj2005.0144 CrossRefGoogle Scholar
- Haaland, S.E.: Simple and explicit formulas for the friction factor in turbulent pipe flow. J. Fluids Eng. 105(1), 89–90 (1983). doi:10.1115/1.3240948 CrossRefGoogle Scholar
- Haghighi, E., Or, D.: Evaporation from porous surfaces into turbulent airflows: coupling eddy characteristics with pore scale vapor diffusion. Water Resour. Res. 49(12), 8432–8442 (2013). doi:10.1002/2012WR013324 CrossRefGoogle Scholar
- Haghighi, E., Or, D.: Interactions of bluff-body obstacles with turbulent airflows affecting evaporative fluxes from porous surfaces. J. Hydrol. 530, 103–116 (2015). doi:10.1016/j.jhydrol.2015.09.048 CrossRefGoogle Scholar
- Haghighi, E., Shahraeeni, E., Lehmann, P., Or, D.: Evaporation rates across a convective air boundary layer are dominated by diffusion. Water Resour. Res. 49(3), 1602–1610 (2013). doi:10.1002/wrcr.20166 CrossRefGoogle Scholar
- Hahn, S., Je, J., Choi, H.: Direct numerical simulation of turbulent channel flow with permeable walls. J. Fluid Mech. 450, 259–285 (2002). doi:10.1017/S0022112001006437 CrossRefGoogle Scholar
- Hanna, O.T., Sandell, O.C., Mazet, P.R.: Heat and mass transfer in turbulent flow under conditions of drag reduction. AIChE J. 27(4), 693–697 (1981). doi:10.1002/aic.690270424 CrossRefGoogle Scholar
- Helmig, R.: Multiphase Flow and Transport Processes in the Subsurface: A Contribution to the Modeling of Hydrosystems. Springer, Berlin (1997)CrossRefGoogle Scholar
- Huber, R., Helmig, R.: Node-centered finite volume discretizations for the numerical simulation of multiphase flow in heterogeneous porous media. Comput. Geosci. 4, 141–164 (2000). doi:10.1023/A:1011559916309 CrossRefGoogle Scholar
- Jambhekar, V.A., Helmig, R., Schröder, N., Shokri, N.: Free-Flow–Porous-Media Coupling for Evaporation-Driven Transport and Precipitation of Salt in Soil. Transp. Porous Media. 110, 251–280 (2015). doi:10.1007/s11242-015-0516-7 CrossRefGoogle Scholar
- Johansen, O.: Thermal conductivity of soils. Ph.D. Thesis, (CRREL draft transl. 637, 1977), Norwegian University of Science and Technology, Trondheim, Norway (1975)Google Scholar
- Krafczyk, M., Kucher, K., Wang, Y., Geier, M.: DNS/LES studies of turbulent flows based on the cumulant lattice boltzmann approach. In: Nagel, W.E., Kröner, D.H., Resch, M.M. (eds) High Performance Computing in Science and Engineering’14, Springer International Publishing, pp 519–531. doi:10.1007/978-3-319-10810-0_34 (2015)
- Kuznetsov, A.V.: Numerical modeling of turbulent flow in a composite porous/fluid duct utilizing a two-layer k-\(\varepsilon \) model to account for interface roughness. Int. J. Therm. Sci. 43(11), 1047–1056 (2004). doi:10.1016/j.ijthermalsci.2004.02.011 CrossRefGoogle Scholar
- Kuznetsov, A.V., Becker, S.M.: Effect of the interface roughness on turbulent convective heat transfer in a composite porous/fluid duct. Int. Commun. Heat Mass Transf. 31(1), 11–20 (2004). doi:10.1016/S0735-1933(03)00197-0 CrossRefGoogle Scholar
- Laurindo, J.B., Prat, M.: Numerical and experimental network study of evaporation in capillary porous media. Drying rates. Chem. Eng. Sci. 53(12), 2257–2269 (1998). doi:10.1016/S0009-2509(97)00348-5 CrossRefGoogle Scholar
- Lehmann, P., Assouline, S., Or, D.: Characteristic lengths affecting evaporative drying of porous media. Phys. Rev. E 77(5), 056,309 (2008). doi:10.1103/PhysRevE.77.056309 CrossRefGoogle Scholar
- Millington, R., Quirk, J.: Permeability of porous solids. Trans. Faraday Soc. 57, 1200–1207 (1961). doi:10.1039/TF9615701200 CrossRefGoogle Scholar
- Mosthaf, K., Baber, K., Flemisch, B., Helmig, R., Leijnse, A., Rybak, I., Wohlmuth, B.: A coupling concept for two-phase compositional porous-medium and single-phase compositional free flow. Water Resour. Res. 47(10), W10522 (2011). doi:10.1029/2011WR010685 CrossRefGoogle Scholar
- Mosthaf, K., Helmig, R., Or, D.: Modeling and analysis of evaporation processes from porous media on the REV scale. Water Resour. Res. 50, 1059–1079 (2014). doi:10.1002/2013WR014442 CrossRefGoogle Scholar
- Nield, D.: The Beavers–Joseph boundary condition and related matters: a historical and critical note. Transp Porous Med 78, 537–540 (2009). doi:10.1007/s11242-009-9344-y CrossRefGoogle Scholar
- Nuske, P., Joekar-Niasar, V., Helmig, R.: Non-equilibrium in multiphase multicomponent flow in porous media: an evaporation example. Int. J. Heat Mass Transf. 74, 128–142 (2014). doi:10.1016/j.ijheatmasstransfer.2014.03.011 CrossRefGoogle Scholar
- Pedras, M.H., de Lemos, M.J.: Macroscopic turbulence modeling for incompressible flow through undeformable porous media. Int. J. Heat Mass Transf. 44(6), 1081–1093 (2001). doi:10.1016/S0017-9310(00)00202-7 CrossRefGoogle Scholar
- Penman, H.L.: Natural evaporation from open water, bare soil and grass. Proc. R Soc. Lond. A Math. Phys. Eng. Sci. 193(1032), 120–145 (1948). doi:10.1098/rspa.1948.0037 CrossRefGoogle Scholar
- Pope, S.B.: Turbulent Flows, 4th edn. Cambridge University Press, Cambridge (2006)Google Scholar
- Rotta, J.C.: Turbulent boundary layers in incompressible flow. Progr. Aerosp. Sci. 2, 1–219 (1962). doi:10.1016/0376-0421(62)90014-3 CrossRefGoogle Scholar
- Rybak, I., Magiera, J., Helmig, R., Rohde, C.: Multirate time integration for coupled saturated/unsaturated porous medium and free flow systems. Comput. Geosci. 19(2), 299–309 (2015). doi:10.1007/s10596-015-9469-8 CrossRefGoogle Scholar
- Saffman, P.: On the boundary condition at the surface of a porous medium. Stud. Appl. Math. L, 93–101 (1971). doi:10.1002/sapm197150293 CrossRefGoogle Scholar
- Sahraoui, M., Kaviany, M.: Slip and no-slip velocity boundary conditions at interface of porous, plain media. Int. J. Heat Mass Transf. 35(4), 927–943 (1992). doi:10.1016/0017-9310(92)90258-T CrossRefGoogle Scholar
- Schlichting, H., Gersten, K.: Grenzschicht-Theorie, 9th edn. Springer, Berlin (1997)CrossRefGoogle Scholar
- Schneider-Zapp, K., Ippisch, O., Roth, K.: Numerical study of the evaporation process and parameter estimation analysis of an evaporation experiment. Hydrol. Earth Syst. Sci. 14(5), 765–781 (2010). doi:10.5194/hess-14-765-2010 CrossRefGoogle Scholar
- Schwenck, N., Beck, M., Becker, B., Class, H., Fetzer, T., Flemisch, B., Grüninger, C., Hommel, J., Jambhekar, V., Kissinger, A., Koch, T., Schneider, M., Schröder, N., Seitz, G., Weishaupt, K.: DuMuX 2.8.0. doi:10.5281/zenodo.31611 (2015)
- Shahraeeni, E., Or, D.: Thermo-evaporative fluxes from heterogeneous porous surfaces resolved by infrared thermography. Water Resour. Res. 46(9), W09,511 (2010). doi:10.1029/2009WR008455 CrossRefGoogle Scholar
- Shahraeeni, E., Lehmann, P., Or, D.: Coupling of evaporative fluxes from drying porous surfaces with air boundary layer: characteristics of evaporation from discrete pores. Water Resour. Res. 48(9), W09525 (2012). doi:10.1029/2012WR011857 CrossRefGoogle Scholar
- Shokri, N., Or, D.: What determines drying rates at the onset of diffusion controlled stage-2 evaporation from porous media? Water Resour. Res. (2011). doi:10.1029/2010WR010284 Google Scholar
- Shukla, J., Mintz, Y.: Influence of land-surface evapotranspiration on the earth’s climate. Science 215, 1498–1501 (1982). doi:10.1126/science.215.4539.1498 CrossRefGoogle Scholar
- Smits, K.M., Sakaki, T., Limsuwat, A., Illangasekare, T.H.: Thermal conductivity of sands under varying moisture and porosity in drainage–wetting cycles. Vadose Zone J. 9(1), 172–180 (2010). doi:10.2136/vzj2009.0095 CrossRefGoogle Scholar
- Smits, K.M., Cihan, A.C., Sakaki, T., Illangasekare, T.H.: Evaporation from soils under thermal boundary conditions: experimental and modeling investigation to compare equilibrium- and nonequilibrium-based approaches. Water Resour. Res. 47(5), W05540 (2011). doi:10.1029/2010WR009533 CrossRefGoogle Scholar
- Sugita, F., Kishii, T.: Effect of roughness distribution on evaporation processes over non-homogeneous sand surfaces: a wind tunnel investigation. Hydrol. Process. 16(11), 2141–2153 (2002). doi:10.1002/hyp.1147 CrossRefGoogle Scholar
- Suzuki, S., Maeda, S.: On the mechanism of drying of granular bed. J. Chem. Eng. Jpn. 1, 26–31 (1968). doi:10.1252/jcej.1.26
- Trautz, A.C., Smits, K.M., Cihan, A.: Continuum-scale investigation of evaporation from bare soil under different boundary and initial conditions: An evaluation of nonequilibrium phase change. Water. Resour. Res. 51, 7630–7648 (2015). doi:10.1002/2014WR016504 CrossRefGoogle Scholar
- Truckenbrodt, E.: Elementare Strömungsvorgänge dichteveränderlicher Fluide. In: Fluidmechanik, 4th edn, Klassiker der Technik, Springer, Berlin, pp. 1–111. doi:10.1007/978-3-540-79024-2_1 (2008)
- van Brakel, J.: Advances in drying, vol 1, Hemisphere, Chap Mass transfer in convective drying, pp. 217–267 (1980)Google Scholar
- van Driest, E.R.: On turbulent flow near a wall. AIAA J. 23(11), 1007–1011 (1956). doi:10.2514/8.3713 Google Scholar
- van Genuchten, M.T.: A closed-form equation for predicting the hydraulic conductivity of unsaturated soils. Soil Sci. Soc. Am. J. 44(5), 892–898 (1980). doi:10.2136/sssaj1980.03615995004400050002x CrossRefGoogle Scholar
- Vanderborght, J., Graf, A., Steenpass, C., Scharnagl, B., Prolingheuer, N., Herbst, M., Franssen, H.J.H., Vereecken, H.: Within-field variability of bare soil evaporation derived from eddy covariance measurements special section: patterns. Vadose Zone J. 9(4), 943–954 (2010). doi:10.2136/vzj2009.0159 CrossRefGoogle Scholar
- Verboven, P., Flick, D., Nicolaï, B., Alvarez, G.: Modelling transport phenomena in refrigerated food bulks, packages and stacks: basics and advances. Int. J. Refrig 29(6), 985–997 (2006). doi:10.1016/j.ijrefrig.2005.12.010 CrossRefGoogle Scholar
- White, F.M.: Fluid Mechanics, 7th edn. McGraw-Hill, Singapore (2011)Google Scholar
- Wilcox, D.C.: Turbulence Modeling for CFD, 3rd edn. DCW Industries, La Cañada (2006)Google Scholar
- Yiotis, A.G., Tsimpanogiannis, I.N., Stubos, A.K., Yortsos, Y.C.: Coupling between external and internal mass transfer during drying of a porous medium. Water Resour. Res. 43(W06403), 1–12 (2007). doi:10.1029/2006WR005558 Google Scholar
- Zhang, C., Li, L., Lockington, D.: A physically based surface resistance model for evaporation from bare soils. Water Resour. Res. 51, 1084–1111 (2015). doi:10.1002/2014WR015490 CrossRefGoogle Scholar
Copyright information
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.