Advertisement

Refractories and Industrial Ceramics

, Volume 60, Issue 4, pp 336–345 | Cite as

Experimental and Numerical Study of the Formation of Thermophysical Characteristics of Carbon Composite Materials. Part 2. Numerical Simulation of Operability of a Refractory Product Made of Carbon Composite Material

  • S. A. KolesnikovEmail author
  • L. V. Kim
  • V. R. Dudin
Article
  • 1 Downloads

A heating of a carbon-made product and thermophysical properties of a carbon material in the temperature range from 300 to 2,500 K were studied. A discrete-heterogeneous mechanism of heating the surface of a multi-dimensionally reinforced carbon-carbon composite material (CCCM) subject to accelerated heating was revealed. Based on the results of testing carbon materials in the temperature range from 300 to 3,000 K, a numerical stress analysis of the product was performed, in which the arising stress condition was considered to be resultant from constraining the deformation of the heated parts of the product by relatively cold fragments. The safety factor levels were found for different parts of the product. It was shown that an additional increase in thermal strength as part of the combined definition of thermal resistance of CCCM products is associated with high thermal conductivity of 1D-reinforced rods of material structure.

Keywords

carbon-carbon composite material (CCCM) structural graphite discrete-heterogeneous mechanism of heat conductance surface of reinforced product radioisotope generator heat-protective housing of radiation heat source (RHS) 

References

  1. 1.
    C. W. Ohlhorst, W. L. Vauhn, P. O. Ransone, and H.-T. Tsou, Thermal conductivity database of various structural carbon-carbon composite materials, Langley Research Center, Hampton, Virginia (1997), http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.82.682&rep=rep1&type=pdf.
  2. 2.
    Ch. Pradere, Thermal and thermomechanical characterization of carbon and ceramic fibers at very high temperature, Ecole Natiionale Superiered’Arts et Metiers Centre de Bordeaux (2004), https://pastel.archives-ouvertes.fr/file/index/docid/500111/filename/ThesePradere.pdf.
  3. 3.
    W.-J. Li, H.-M. Huang, Y.-M. Hu, “Thermochemical ablation of carbon/carbon composites with non-linear thermal conductivity,” Thermal Science, 18(5), 1625 – 1629 (2014), http://www.doiserbia.nb.rs/img/doi/0354-9836/2014/0354-98361405625L.pdf.CrossRefGoogle Scholar
  4. 4.
    J. Lachaud, Y. Aspa, G. L. Vignoles, and J.-M. Goyheneche, 3D modeling of thermochemical ablation in carbon-based materials: effect of anisotropy on surface roughness onset, http://jeanlachaud.com/research/lachaud-ISMSE2006.pdf.
  5. 5.
    M. Grujicic, C. L. Zhao, E. C. Dusel, et al., “Computational analysis of the thermal conductivity of the carbon–carbon composite materials,” J. Mater. Sci., 41(24), 8244 – 8256 (2006), https://link.springer.com/article/10.1007/s10853-006-1003-x.CrossRefGoogle Scholar
  6. 6.
    Patent RU249896, G. A. Krechka, V. D. Kleymenov, and V. N. Savelyev, Reinforcing frame made of carbon-carbon composite material, Application No. 2011127880/02, appl. date: July 06, 2011, publ. date: Nov. 20, 2013, Bul. No. 32. http://www.findpatent.ru/patent/249/2498962.html.
  7. 7.
    O. N. Dementyev, G. F. Kostin, N. N. Tikhonov, and B. M. Tyulkin, “Assessment of the effect of mechanically carried away particles of the thermal protection of hypersonic aircraft on stability of the boundary layer flow and heat transfer,” Vestn. Chelyab. Gos. Univ., Fizika, 13, No. 14(268), 9 – 13 (2012), https://cyberleninka.ru/article/n/otsenka-vliyaniya-mehanicheskiunosimyhchastits- teplovoy-zaschity-giperzvukovyh-letatelnyhapparatov-na-ustoychivost-techeniya-v.
  8. 8.
    I. A. Izhenbin, Tomographic system based on “Orel” tomograph for performing tomographic scanning of the samples of 39p7.001 and 4KMC-L type carbon-carbon composite materials, Electronic Scientific Archive of the Tomsk Polytechnic University (2016), http://earchive.tpu.ru/bitstream/11683/28151/1/TPU174557.pdf.
  9. 9.
    H.-B. Shi, M Tang, B. Gao, and J.-M. Su, “Effect of graphitization parameters on the residual stress in 4D carbon fiber/carbon composites,” New Carbon Materials, 26(4), 287 – 288 (2011), 10. 1016/S1872-5805(11)60082-6. https://www.sciencedirect.com/journal/new-carbon-materials/vol/26/issue/4.CrossRefGoogle Scholar
  10. 10.
    S. A. Kolesnikov, M. Yu. Bamborin, V. A. Vorontsov, et al., “Formation of carbon-carbon composite material thermal conductivity standards,” Refract. Ind. Ceram., 58(1), 94 – 102 (2017)CrossRefGoogle Scholar
  11. 11.
    S. A. Kolesnikov, L. V. Kim, V. A. Vorontsov, Study of thermophysical property formation of spatially reinforced carbon- carbon composite material, Refract. Ind. Ceram., 58(4), 439 – 449 (2017).CrossRefGoogle Scholar
  12. 12.
    The United Nations, A/AC.105/C.1/L.312, Principles concerning the use of nuclear power sources in outer space, adopted by the General Assembly Resolution 47/68 dated December 14 (1992), http://www.un.org/ru/documents/decl_conv/conventions/outerspace_nucpower.shtml.
  13. 13.
    A. K. Protsenko and S. A. Kolesnikov, Development of carbon- carbon technologies and their development potential, In: “55 years of the Research Institute of Graphite-based Structural Materials”, Nauchnye Tekhnologii, Moscow (2015), http://www.niigrafit.ru/nauka-i-obrazovanie/sbornik.pdf.
  14. 14.
    V. V. Khartov, M. B. Martynov, A. V. Lukyanchikov, and S. N. Aleksashkin, “Design concept of the landing module “ExoMars-2018,” being developed by the NPO named after S. A. Lavochkin,” Vestn. NPO named after S. A. Lavochkin, No. 2 (23), 5 – 12 (2014).Google Scholar
  15. 15.
    Yu. V. Polezhaev and F. B. Yuryevich, Thermal Protection [in Russian], Ed. by A. V. Lykov, Energiya, Moscow (1976).Google Scholar
  16. 16.
    Thermal unit of the “Angel” radioactive thermoelectric generator, https://helpiks.org/6-77726.html.
  17. 17.
    R. Upadhyay, P. T. Bauman, R. Stogner, et al., Steady-state ablation model coupling with hypersonic flow, 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition, Orlando, Florida, Jan. 4 – 7 (2010), pp. 1 – 10. https://arc.aiaa.org/doi/10.2514/6.2010-1176.
  18. 18.
    Multi-dimensional reinforced carbon-carbon composites. http://niigrafit.ru/produktsiya/kompozity.php.
  19. 19.
    L. M. Manocha, “High performance carbon-carbon composites,” Sadhana, 28, parts 1/2, 349 – 358 (2003), http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.582.8031&rep=rep1&type=pdf.
  20. 20.
    V. L. Salich, “Design of the chamber of the 100 N propulsion oxygen-hydrogen rocket engine based on numerical simulation of intrachamber processes,” Vestn. UGATU, 18, 4 (65), 20 – 26 (2014), http://journal.ugatu.ac.ru.
  21. 21.
    V. P. Sosedov, V. G. Nagornyi, A. S. Kotosonov, et al., Properties of Graphite-based Structural Materials [in Russian], Reference guide, Metallurgiya, Moscow (1975).Google Scholar
  22. 22.
  23. 23.
    S. P. Timoshenko and J. Goodyear, The Theory of Elasticity, 2nd ed., transl. from English, ed. by G. S. Shapiro, Nauka, Glavn. Red. Fiz. Mat. Lit., Moscow (1979).Google Scholar
  24. 24.
    A. P. Karpov and G. Ye. Mostovoi, “High-temperature mechanical properties of carbon and carbon-carbon composite materials,” Perspect. Mater., No. 3, 13 – 21 (2015).Google Scholar
  25. 25.
    L. M. Akselrod and A. V. Zabolotskii, “Mathematical simulation of fracturing of the lining of metallurgical equipment under thermal shock conditions,” Sborn. Nauchn. Idei, Sovr. Nauka, No. 2 (4), 165 – 169 (2010), http://modern.science.triacon.org/ru/issues/2010/files/papers/2/165-169.pdf.
  26. 26.
    S. A. Kolesnikov, G. E. Mostovoi, S. V. Vasil’chenko, et al., “High-temperature treatment of carbon-carbon composite materials. Part 2. Thermal stabilization of two-dimensionally reinforced carbon-carbon composite material object geometry,” Refract. Ind. Ceram., 53(3), 185 – 192 (2012).CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  1. 1.JSC “NIIGrafit”,MoscowRussia

Personalised recommendations