Metal Science and Heat Treatment

, Volume 59, Issue 11–12, pp 675–681 | Cite as

Improvement of Properties of High-Strength Cast Irons by Surfacing a Metal with Globular Graphite

CAST IRONS
  • 2 Downloads

The possibility of sparing reconditioning of parts and mechanisms produced from high-strength cast iron by surfacing a metal identical to the base one but containing no scarce and expensive elements is studied. The chemical composition of the coating is determined experimentally. The mechanical properties of the deposited metal are determined. The results of the experiment are analyzed, and the composition of the powder wire blend providing formation of a ferrite-pearlite structure and globular graphite in the surfaced metal is determined. The structural components of the deposited metal are described. The optimum content of calcium in the cast iron with structurally free globular graphite is specified.

Key words

high-strength cast iron structural materials surfacing elongation hardness conventional yield strength globular graphite ultimate tensile strength alloying composition microstructure 

References

  1. 1.
    N. N. Aleksandrov, “High-strength iron with globular graphite: a promising structural material of the XXI century,” Mater. Armaturostr., No. 2(53), 72 – 74 (2008).Google Scholar
  2. 2.
    V. B. Bublikov, “Sixty years of high-strength cast iron,” Liteinoe Proizvod., No. 11, 2 – 8 (2008).Google Scholar
  3. 3.
    A. S. Chaus, “Special features of the microstructure of cast iron with globular graphite,” Metalloved. Term. Obrab. Met., No. 7, 15 – 22 (2015).Google Scholar
  4. 4.
    V. I. Moshchenok, D. B. Glushkova, V. P. Tarabanova, and S. V. Dembitskii, “Elevation of the operating properties of parts from high-strength cast iron,” Vest. Kharkov. Nats. Avtomob.-Dorozhn. Univ., Issue 33, 1 – 4 (2006).Google Scholar
  5. 5.
    V. Z. Kutsova, M. A. Kovzel’, A. V. Grebeneva, et al., “Effect of alloying elements on formation of structure, phase composition and properties of chromium-manganese iron in cast condition,” Metallurg. Gornorud. Prom., No. 3(294), 45 – 48 (2015).Google Scholar
  6. 6.
    Y. Bacha and A. S. Chaus, “Effect of plastic deformation on the structure and properties of cast iron with globular graphite,” Metalloved. Term. Obrab. Met., No. 5, 11 – 24 (2004).Google Scholar
  7. 7.
    K. V. Makarenko, “Simulation of the process of crystallization of cast iron with globular graphite,” Metalloved. Term. Obrab. Met., No. 11, 16 – 20 (2009).Google Scholar
  8. 8.
    A. S. Chaus, J. Sojka, and L. Chaplovic, “Special features of internal structure of globular graphite in high-strength cast iron,” Metalloved. Term. Obrab. Met., No. 4, 9 – 14 (2013).Google Scholar
  9. 9.
    A. I. Gruvman, A. Z. Glebov,M. S. Polukhin, and V. V. Goncharov, “Replacement of bronze spigots by spigots from bainitic high-strength iron,” in: Science and Production, Mater. Int. Workshop, Bryansk, 19 – 20 March, 2009 [in Russian], Izd. BGTU, Bryansk (2009), pp. 34 – 36.Google Scholar
  10. 10.
    T. S. Koblo, M. V. Marchenko, and E. V. Rovnyi, “Factors affecting the quality of cylinder spigots of diesel engines from high-strength cast iron,” Vest. KhNTUSG Im. P. Vasilenka, Issue 146, 29 – 34 (2014).Google Scholar
  11. 11.
    D. V. Starostenko and N. I. Mozgovoy, “Innovative machine building technologies used for manufacturing rails from high-strength cast iron,” in: Problems of Raising the Efficiency of Metal Treatment in Today’s Industry, Proc. 1st All-Russian Conf., Novosibirsk, March 27, 2013 [in Russian], Novosibirsk (2013), p. 54.Google Scholar
  12. 12.
    I. V. Marshirov, G. A. Mustafin, V. G. Moskalev, et al., “Production of high-strength iron with globular graphite for castings for agricultural machine building,” Polzunovskii Almanakh, No. 3, 203 – 204 (2008).Google Scholar
  13. 13.
    N. I. Bestuzhev, A. N. Krutilin, V. A. Stefanovich, et al., “Gears from bainitic high-strength cast iron,” Liteinoe Proizvod., No. 5, 2 – 7 (2009).Google Scholar
  14. 14.
    Yu. A. Vasenko and D. A. Demin, “Simulation of the wear resistance of titanium-alloyed cast iron using data of passive experiment,” in: L. L. Tovazhnayan’skii (ed.), Information Technologies: Science, Engineering, Technology, Education, Health, Abstr. Int. Workshop, Part II, 15 – 17 May 2012, Kharkov [in Russian], NTU “KhPI,” Kharkov, p. 10.Google Scholar
  15. 15.
    V. A. Kosyachkov, “Widening of the possibilities of the production of castings by inoculating cast iron in a mold,” Liteinoe Proizvod., No. 9, 6 – 8 (2004).Google Scholar
  16. 16.
    V. B. Bublikov, A. A. Yasinskii, L. N. Syroporshnev, et al., “Special features of the influence of silicon on the structure and mechanical properties of castings from high-strength iron inoculated in the casting mold,” Prots. Lit’ya, No. 3(81), 46 – 57 (2010).Google Scholar
  17. 17.
    T. S. Skoblo and S. A. Burtsev, “Analysis of the methods of inoculation of high-strength irons,” Vest. KhNTUSG Im. P. Vasilenka: Prob. Nadezh. Mash. Sredstv Mekhaniz. Selskokhoz. Proizvod., Issue 69, 192 – 198 (2008).Google Scholar
  18. 18.
    E. V. Kovalevich, “Theoretical fundamentals of the choice of inoculant for producing cast iron with globular graphite without pyroeffect,” Liteishch. Rossii, 8, 29 – 31 (2008).Google Scholar
  19. 19.
    V. B. Bublikov, A. A. Yasinkskii, L. N. Syroporshnev, et al., “Effect of manganese content and cooling rate on crystallization, structure formation and mechanical properties of high-strength cast iron,” Prots. Lit’ya, 6, 28 – 34 (2009).Google Scholar
  20. 20.
    A. V. Lisovskii, “Control of the evolution of structure as a means for raising the operating properties of articles from high-strength iron,” in: Proc. 7th Int. Sci.-Eng. Conf. “Advanced Metallurgy of the New Millennium,” Part 1 [in Russian], Lipetsk (2010), pp. 104 – 109.Google Scholar
  21. 21.
    T. P. Govorun and A. I. Lyubich, “Theoretical substantiation and development of economically alloyed welding materials,” Welding Int., 30(6), 432 – 458 (2015).Google Scholar
  22. 22.
    A. I. Lyubich, T. P. Govorun, S. V. Marchenko, and I. O. Varukha, “Investigation of the effect of titanium on formation of wear resistant alloy,” Metallofiz. Noveish. Tekhnol., 35(5), 645 – 658 (2013).Google Scholar
  23. 23.
    Yu. P. Adler, E. V. Makarova, and Yu. V. Granovskii, Design of Experiment in the Search for Optimum Conditions [in Russian], Nauka, Moscow (1971), 279 p.Google Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Sumy State UniversitySumyUkraine

Personalised recommendations