Advertisement

Measurement of Banded Microstructure Characteristics in Sheet Steels

  • A. V. KudryaEmail author
  • E. A. Sokolovskaya
  • V. Yu. Perezhogin
  • D. U. Smagulov
  • G. E. Akhmetova
Article
  • 2 Downloads

The article discusses factors determining the reproducibility of measurement results for a banded microstructure in sheet steels St3sp and 09G2s using computerized procedures.

Keywords

sheet steels microstructure ferrite-pearlite and ferrite-bainite banding computerized procedures classical and non-parametric statistics 

References

  1. 1.
    Yu. S. Karabasov (editor), Steel on the Verge of the Century [in Russian], MISiS, Moscow (2001).Google Scholar
  2. 2.
    M. A. Shtremel’, Steel Strength. Part II. Deformation [in Russian], MISiS, Moscow (1997).Google Scholar
  3. 3.
    M. A. Shtremel’, Failure. In 2 Books, Book 2. Structure Failure [in Russian], MISiS, Moscow (2015).Google Scholar
  4. 4.
    M. A. Shtremel’, Failure. In 2 Books, Book 1. Material Failure [in Russian], MISiS, Moscow (2014).Google Scholar
  5. 5.
    L. I. Éfron, Materials Science in Large Metallurgy. Pipe Steels [in Russian], Metallurgiya, Moscow (2012).Google Scholar
  6. 6.
    E. V. Proskurkin, V. I. Bol’shakov, T. A. Dergach, et al., “Effective coating for increasing the operating reliability of pipes in complex oil recovery conditions,” Stal’, No. 9, 6–64 (2013).Google Scholar
  7. 7.
    A. A. Kazakov, D. V. Kiselev, S. V. Andreeva, et al., “Development of a procedure for quantitative evaluation of the banded microstructure of low-alloy pipe steels by means of automated image analysis,” Chern. Met., July-August, 31–37 (2007).Google Scholar
  8. 8.
    É. A. Sokolovskaya, “Reproducibility of measurement results for structure and fractures using computerized procedures,” Vopr. Materialoved., No. 4(76), 143–153 (2013).Google Scholar
  9. 9.
    A. V. Kudrya, É. A. Sokolovskaya, V. A. Trachenko, et al., “Measurement of failure inhomogeneity in structural steels with a different structure,” Metall. Term. Obrab. Metallov, No. 4(718), 12–18 (2015).Google Scholar
  10. 10.
    A. V. Kudrya, É. A. Sokolovskaya, Kh. N. Li, et al., “Evaluation of the structure of fractures in structural steels using computerized procedures,” Vektor Nauki Tolyat. Gos. Univ., No. 4(34), 44–52 (2015).Google Scholar
  11. 11.
    L. A. Kondratov, Development of Pipe Manufacture [in Russian], Metallurgizdat, Moscow (2015).Google Scholar
  12. 12.
    Yu. G. Dragunov, A. S. Zubchenko, Yu. V. Kashirskii, et al., Grade Steels and Alloys [in Russian], Innovats. Mash., Moscow (2014).Google Scholar
  13. 13.
    A. V. Kudrya, É. A. Sokolovskaya, V. A. Trachenko, et al., “Inhomogeneity factors for sheet steel quality,” Élektrometallurgiya, No. 9, 23–33 (2013).Google Scholar
  14. 14.
    V. E. Gmurman, Probability Theory and Mathematical Statistics: Textbook [in Russian], Vyssh. Shk., Moscow (2003).Google Scholar
  15. 15.
    A. V. Kudrya, É. A. Sokolovskaya, V. Yu. Perezhogin, et al., “Use of computerized procedures for evaluating hard alloy structure inhomogeneity,” Metallurg, No. 12, 77–80 (2016).Google Scholar
  16. 16.
    A. V. Kudrya, É. A. Sokolovskaya, S. V. Skorodumov, et al., “Possibility of digital light microscopy for objective evaluation of metal product quality,” Metalloved. Term. Obrab. Materialov, No. 4(754), 15–23 (2018).Google Scholar
  17. 17.
    M. A. Smirnov, I. Yu. Pyshmintsev, and A. N. Boryakova, “Classification of low-carbon pipe steel microstructures,” Metallurg, No. 7, 45–51 (2010).Google Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  • A. V. Kudrya
    • 1
    Email author
  • E. A. Sokolovskaya
    • 1
  • V. Yu. Perezhogin
    • 1
  • D. U. Smagulov
    • 2
  • G. E. Akhmetova
    • 2
  1. 1.National Research Technological University MISiSMoscowRussia
  2. 2.K. Satpaev Kazakh National Research Technical UniversityAlmatyKazakhstan

Personalised recommendations