Advertisement

Journal of Sol-Gel Science and Technology

, Volume 88, Issue 1, pp 105–113 | Cite as

A novel silica aerogel microspheres loaded with ammonium persulfate gel breaker for mid-deep reservoirs

  • Yang Gong
  • Yaofei Lei
  • Xiaohong Chen
  • Huaihe Song
  • Ran Liu
Original Paper: Industrial and technological applications of sol–gel and hybrid materials
  • 128 Downloads

Abstract

As one of the important additives in the process of petroleum’s exploitation, the gel breaker is a key factor to determine whether the exploitation can be completed successfully. Here, a novel porous SiO2 aerogel microsphere loaded with ammonium persulfate (aAPS) with obvious delay-releasing performance under higher temperature and pressure was synthesized by the process of sol–gel and water-in-oil (W/O) inverse emulsion polymerization. The obtained gel breaker was characterized by scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). The releasing rate of ammonium persulfate of gel breakers under different conditions was determined by pH meter method. The results show that the loading of APS is about 53 wt% and the releasing rate is significantly affected by temperature and time.

The whole process showing the preparation and the release process of aAPS is illustrated in Fig. 1. Porous silica aerogel microspheres were prepared by sol-gel and water-in-oil (W/O) inverse emulsion polymerization. During the drying process, ammonium persulfate precipitates are still present in these pores when the solution evaporates in the microsphere and then are successfully obtained by the silica aerogel loaded with ammonium persulfate. During the release process, ammonium persulfate has a concentration difference in the interior of the microsphere and in the environment of the system. Under this concentration difference, APS gradually diffuses into the environment of the system. The presence of the network skeleton of silica aerogel microspheres can greatly prolong the diffusion path of ammonium persulfate, hindering the mutual diffusion and penetration of ammonium persulfate and water molecules, so the breaker has a certain delay release.

Highlights

  • The preparation of a novel silica aerogel-based gel breaker by a simple and industrialized method.

  • The releasing rate of the gel breaker can reach about 65% at the temperature of 70 °C.

  • The gel breaker has obvious delay-releasing performance under high temperature and pressure, which can reach about 120–130 min when the temperature reaches up to 70 °C.

  • SiO2 as an environmentally friendly material, instead of polymer materials, greatly reduces the pollution to the environment.

Keywords

Silica aerogel Microspheres Gel breaker Ammonium persulfate 

Notes

Acknowledgements

This work was supported by the National Natural Science Foundation of China (51572014 and 51272019).

Compliance with ethical standards

Conflict of interest

The authors declare that they have no conflict of interest.

Ethical approval

This article does not contain any studies with human participants or animals performed by any of the authors.

Informed consent

Informed consent was obtained from all individual participants included in the study.

References

  1. 1.
    Tang YF, Zheng QF, Chen B, Ma YF, Gong SQ (2017) A new class of flexible nanogenerators consisting of porous aerogel films driven by mechanoradicals. Nano Energy 38:401–411CrossRefGoogle Scholar
  2. 2.
    Githens CJ, Harrison WG (2007) Method for using soap as a soluable fluid loss additive in the hydraulic fracturing treatment of oil and gas wells. WO/2014/190335, 1994Google Scholar
  3. 3.
    Barati R, Johnson SJ, McCool S, Green DW, Willhite P, Liang JT (2011) Fracturing fluid cleanup by controlled release of enzymes from polyelectrolyte complex nanoparticles. J Appl Polym Sci 121:1292–1298CrossRefGoogle Scholar
  4. 4.
    Zuo MM, Liu TQ, Han JJ, Tang YC, Yao F, Yuan YF, Qian ZH (2014) Preparation and characterization of microcapsules containing ammonium persulfate as core by in situ polymerization. Chem Eng J 249:27–33CrossRefGoogle Scholar
  5. 5.
    Dobson James W Jr, Hayden Shauna L, Tresco Kim O (2014) Treatment fluids with non-oxidizer class inorganic peroxide polymer breakers and methods of use thereof. WO2009114611A2, 2014Google Scholar
  6. 6.
    Chai QL, Li Y, Dong T (2006) Discussion on the optimum methods of encapsulated breakers. Inner Mongolia. Petrochem Ind 7:142–144Google Scholar
  7. 7.
    Rao ZH, Wang SF, Peng FF (2012) Self diffusion of the nano-encapsulated phase change materials: a molecular dynamics study. Appl Energy 100:303–308CrossRefGoogle Scholar
  8. 8.
    Souguir H, Salaün F, Douillet P, Chatterjee S (2013) Nanoencapsulation of curcumin in polyurethane and polyurea shells by an emulsion diffusion method. Chem Eng J 221:133–145CrossRefGoogle Scholar
  9. 9.
    Bounds C, Goetter R, Pojman J, Vandersall M (2012) Preparation and application of microparticles prepared via the primary amine-catalyzed michael addition of a trithiol to a triacrylate. J Polym Sci Part A 50:409–422CrossRefGoogle Scholar
  10. 10.
    Cui WX, Wang CP (2016) Extrusion and release research of encapsulated gel breaker in fracturing fluid with high pressure. Oilfield Chemistry 33(4):602–622Google Scholar
  11. 11.
    Dong W, Wang JY, Wang WT (2003) Preparation of microcapsulated gel breaker ZYEB for water base fracturing fluids. Oilfield Chemistry 20(3):221–223Google Scholar
  12. 12.
    Chen XQ, Shu FC, Li WP (2010) A kind of slow release gel breaker was used for PRD drilling fluid. Dril Fluid Compl Fluid 27:33–37Google Scholar
  13. 13.
    Chen T, Zhou X, Dang W, Niu ZQ, Zhou FX, Yang JP (2016) Properties of the MCB series microcapsule gel breaker. Dril Fluid Compl Fluid 33:114–116Google Scholar
  14. 14.
    Lei YF, Chen XH, Hu ZJ, Song HH, Cao B (2017) A general strategy for improving the thermal insulation performance of aerogels by multiple impregnation. Scr Mater 139:5–8CrossRefGoogle Scholar
  15. 15.
    Zu GQ, Shen J, Zou LP (2013) Nano engineering super heat-resistant, strong alumina aerogels. Chem Mater 25:4757–4764CrossRefGoogle Scholar
  16. 16.
    Zhao SY, Zhang Z, Sèbe G, Wu R, Virtudazo RV, Tingaut P (2015) Multiscale assembly of superinsulating silica aerogels within silylated nanocellulosic scaffolds: improved mechanical properties promoted by nanoscale chemical compatibilization. Adv Funct Mater 25:2326–2334CrossRefGoogle Scholar
  17. 17.
    Stergar J, Maver U (2016) Review of aerogel-based materials in biomedical applications. J Sol-Gel Sci Technol 77:738–752CrossRefGoogle Scholar
  18. 18.
    Horvat G, Pantic´ M, Novak Z, Knez Z (2015) Supercritical impregnation of drugs and supercritical fluid deposition of metals into aerogels. J Mater Sci 50:1–12CrossRefGoogle Scholar
  19. 19.
    Gonçalves V, Gurikov P, Poejo J, Matias AA, Heinrich A, Martins Duarte CM, Smirnova I (2016) Alginate-based hybrid aerogel microparticles for mucosal drug delivery. Eur J Pharm Biopharm 107:160–170CrossRefGoogle Scholar
  20. 20.
    Smirnova I, Suttiruengwong S, Seiler M, Arlt W (2004) Dissolution rate enhancement by adsorption of poorly soluble drugs on hydrophilic silica aerogels. Pharm Dev Technol 9(4):443–452CrossRefGoogle Scholar
  21. 21.
    Smirnova I, Suttiruengwong S, Arlt W (2004) Feasibility study of hydrophilic and hydrophobic silica aerogelsas drug delivery systems. J Non-Cryst Solids 350:54–60CrossRefGoogle Scholar
  22. 22.
    Lei YF, Chen XH, Song HH, Hu ZJ, Cao B (2017) The influence of thermal treatment on the microstructure and thermal insulation performance of silica aerogels. J Non-Cryst Solids 470:178–183CrossRefGoogle Scholar
  23. 23.
    Péter V, Dániel S, Imre D, Pavel G, Irina S, István F, József K (2018) A redox strategy to tailor the release properties of Fe(III)-alginate aerogels for oral drug delivery. Carbohydr Polym 188:159–167CrossRefGoogle Scholar
  24. 24.
    Peng B, Luo PY, Guo WY, Yuan Q (2013) Structure-property relationship of polyetheramines as clay-swelling inhibitors in water-based drilling fluids. J Appl Polym Sci 129:1074–1079CrossRefGoogle Scholar
  25. 25.
    Farhad S, Manouchehr M, Mohadeseh S (2013) Sulfonated rice husk ash (RHA-SO3H): a highly powerful and efficient solid acid catalyst for the chemoselective preparation and deprotection of 1,1-diacetates. Catal Commun 36:31–37CrossRefGoogle Scholar
  26. 26.
    Liu HR, Du JH (2006) Synthesis and characterization of MoO2/P(St-co-MMA-co- AA)microspheres via microemulsion by c-ray radiation. Solid State Sci 8:526–530CrossRefGoogle Scholar
  27. 27.
    Chao J, Liu HS, Lang XJ, Liu ZD (2004) Research on preparation of microcapsulated delayed release gel breaker with wurster fluidized bed process. Chem Eng Oil Gas 33:40–43Google Scholar
  28. 28.
    Xie JL, Zhang YT (1996) Study on the three-layer spherical capsule gel breaker. Oil Dril Prod Technol 18:62–67Google Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2018

Authors and Affiliations

  • Yang Gong
    • 1
  • Yaofei Lei
    • 2
  • Xiaohong Chen
    • 1
  • Huaihe Song
    • 1
  • Ran Liu
    • 1
  1. 1.State Key Laboratory of Chemical Resource Engineering Beijing University of Chemical TechnologyBeijingChina
  2. 2.Beijng Satellite Manufacturing PlantBeijingChina

Personalised recommendations