Advertisement

Journal of Materials Science

, Volume 44, Issue 6, pp 1641–1651 | Cite as

Observation of internal pulsed current flow through the ZnO specimen in the spark plasma sintering method

  • Tatsuya MisawaEmail author
  • Noboru Shikatani
  • Yuji Kawakami
  • Takashi Enjoji
  • Yasunori Ohtsu
  • Hiroharu Fujita
Proceedings of the Symposium on Spark Plasma Synthesis and Sintering

Abstract

In spark plasma sintering (SPS), it is supposed that a part of the large pulsed sintering current flows into the specimen and affects the sintering behavior. To clarify the influence of the internal pulsed current that flows through the specimen during SPS, measurement of the electrical resistance of the specimen was conducted using Pt electrodes and the internal pulsed current was successfully observed using a magnetic probe during the sintering of ZnO and other materials. Two Pt electrodes were installed on the sides of a ZnO sample through a carbon die, and decrease of electrical resistance was observed with the progress of sintering. The internal current that flows through the specimen during SPS was several hundred ampere, and the ratio of the internal current to the total current was found to be dependent on the material and the progress of SPS process.

Keywords

Spark Plasma Sinter Probe Position Sinter Behavior Magnetic Probe Sinter Specimen 

Notes

Acknowledgements

The authors would like to thank Dr. K. Ozaki, Materials Research Institute for Sustainable Development, National Institute of Advanced Industrial Science and Technology (AIST), and Dr. Y. Makino, Joining and Welding Research Institute, Osaka University, for helpful discussion. The thorough and helpful comments of reviewers on this article are gratefully acknowledged. This research was partially supported by a Grant-in-Aid for Scientific Research (19740345, 2007) from the Ministry of Education, Science, Sports, and Culture of Japan.

References

  1. 1.
    Matsugi K, Hatayama T, Yanagisawa O (1995) J Jpn Inst Met 59:740CrossRefGoogle Scholar
  2. 2.
    Omori M (2000) Mater Sci Eng A 287:183. doi: https://doi.org/10.1016/S0921-5093(00)00773-5 CrossRefGoogle Scholar
  3. 3.
    Hwan-tae K, Kawahara M, Tokita M (2000) J Jpn Soc Powder Powder Metall 47:887CrossRefGoogle Scholar
  4. 4.
    Yucheng W, Zhengyi F (2002) Mater Sci Eng B 90:34. doi: https://doi.org/10.1016/S0921-5107(01)00780-2 CrossRefGoogle Scholar
  5. 5.
    Chen W, Anselmi-Tamburini U, Garay JE, Groza JR, Munir ZA (2005) Mater Sci Eng A 394:132. doi: https://doi.org/10.1016/j.msea.2004.11.020 CrossRefGoogle Scholar
  6. 6.
    Anselmi-Tamburini U, Gennari S, Garay JE, Munir ZA (2005) Mater Sci Eng A 394:139. doi: https://doi.org/10.1016/j.msea.2004.11.019 CrossRefGoogle Scholar
  7. 7.
    Anselmi-Tamburini U, Garay JE, Munir ZA (2005) Mater Sci Eng A 407:24. doi: https://doi.org/10.1016/j.msea.2005.06.066 CrossRefGoogle Scholar
  8. 8.
    Munir ZA, Anselmi-Tamburini U, Ohyanagi M (2006) J Mater Sci 41:763. doi: https://doi.org/10.1007/s10853-006-6555-2 CrossRefGoogle Scholar
  9. 9.
    Jackson JD (1975) Classical electrodynamics. Wiley & Sons, Inc, 174 pGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC 2008

Authors and Affiliations

  • Tatsuya Misawa
    • 1
    Email author
  • Noboru Shikatani
    • 2
  • Yuji Kawakami
    • 3
  • Takashi Enjoji
    • 3
  • Yasunori Ohtsu
    • 1
  • Hiroharu Fujita
    • 1
  1. 1.Department of Electrical and Electronic Engineering, Faculty of Science and EngineeringSaga UniversitySagaJapan
  2. 2.Department of Life, Environment and Material Science, Faculty of EngineeringFukuoka Institute of TechnologyFukuokaJapan
  3. 3.Department of Material and EnvironmentIndustrial Technology Center of SagaSagaJapan

Personalised recommendations