Advertisement

Geotechnical and Geological Engineering

, Volume 37, Issue 1, pp 375–387 | Cite as

Application of the Cohesion Softening–Friction Softening and the Cohesion Softening–Friction Hardening Models of Rock Mass Behavior to Estimate the Specific Energy of TBM, Case Study: Amir–Kabir Water Conveyance Tunnel in Iran

  • Majid Mirahmadi
  • Mohsen Soleiman DehkordiEmail author
Original Paper
  • 36 Downloads

Abstract

The specific energy (SE) of an excavation is an important factor to consider in economic and technological investigations of mechanical excavation projects using a tunnel-boring machine (TBM). SE is defined as the energy consumed during excavation of per unit volume of rock mass, and it can be determined in real time from the data recording the performance of a TBM. Several experimental, empirical, and analytical methods have been developed to predict SE based on rock mass and machine parameters. In this study, a new empirical method is proposed to predict SE based on the strain energy ratio of rock mass (Ψ). This is defined as the ratio of the residual post peak strain energy to the stored pre peak strain energy of the rock mass. It depends on three important parameters, namely rock mass properties, intact rock parameters, and rock mass behavior models. In this study, to estimate the strain energy ratio of rock mass, two post peak rock mass behavior models—cohesion softening–friction softening (CSFS) and cohesion softening–friction hardening (CSFH)—were used. Based on actual data from the Amir–Kabir water conveyance tunnel project, the relationships between the SE of TBM and the strain energy ratio were investigated. Due to different rock mass qualities in the tunnel route, classification of rock mass according to Hoek and Brown’s proposal was carried out, and the correlation between the mentioned parameters in each class was studied. The results showed a direct relationship between the parameters, and the best relationships in poor and moderate rock mass (geological strength index [GSI] < 65) were obtained using the CSFS model to clarify the rock mass’s post peak behavior, while the CSFH model was highly applicable for estimating the SE of TBM using the strain energy ratio in good rock mass (GSI > 70) because of its ability to modify the brittle behavior of brittle rock mass.

Keywords

Specific energy Strain energy ratio CSFS model CSFH model GSI Amir–kabir water conveyance tunnel 

Notes

Acknowledgements

The authors are indebted to all staff, including consulting engineers, contractors, and employers, especially Sahel Consulting Engineers (SCE), for providing us with data, as well as all individuals who helped to us to prepare this paper.

References

  1. Acaroglu O, Ozdemir L, Asbury B (2008) A fuzzy logic model to predict specific energy requirement for TBM performance prediction. Tunn Undergr Space Technol 23:600–608CrossRefGoogle Scholar
  2. Aghda SF, Ganjalipour K, Zadeh ME (2016) Comparison of squeezing prediction methods: a case study on nowsoud tunnel. Geotech Geol Eng 34:1487–1512CrossRefGoogle Scholar
  3. Alejano L, Rodriguez-Dono A, Alonso E, Fdez-Manin G (2009) Ground reaction curves for tunnels excavated in different quality rock masses showing several types of post-failure behavior. Tunn Undergr Space Technol 24:689–705CrossRefGoogle Scholar
  4. Alejano L, Alonso E, Rodriguez-Dono A, Fernandez-Manin G (2010) Application of the convergence-confinement method to tunnels in rock masses exhibiting Hoek-Brown strain-softening behavior. Int J Rock Mech Min Sci 47:150–160CrossRefGoogle Scholar
  5. Altindag R (2003) Correlation of specific energy with rock brittleness concepts on rock cutting. J S Afr Inst Min Metall 103:163–171Google Scholar
  6. Atici U, Ersoy A (2009) Correlation of specific energy of cutting saws and drilling bits with rock brittleness and destruction energy. J Mater Process Technol 209:2602–2612CrossRefGoogle Scholar
  7. Bieniawski Z, Tamames B, Fernandez J, Hernandez M Rock mass excavability (RME) indicator: new way to selecting the optimum tunnel construction method. In: ITA-AITES world tunnel congress & 32nd ITA general assembly, Seoul, 2006Google Scholar
  8. Cai M, Kaiser P, Tasaka Y, Minami M (2007) Determination of residual strength parameters of jointed rock masses using the GSI system. Int J Rock Mech Min Sci 44:247–265CrossRefGoogle Scholar
  9. Dehkordi MS, Shahriar K, Maarefvand P, Gharouninik M (2011) Application of the strain energy to estimate the rock load in non-squeezing ground condition. Arch Min Sci 56:551–566Google Scholar
  10. Dehkordi MS, Shahriar K, Moarefvand P, Gharouninik M (2013) Application of the strain energy to estimate the rock load in squeezing ground condition of Eamzade Hashem tunnel in Iran. Arab J Geosci 6:1241–1248CrossRefGoogle Scholar
  11. Dehkordi MS, Lazemi H, Shahriar K (2014) Application of the strain energy ratio and the equivalent thrust per cutter to predict the penetration rate of TBM, case study: Karaj-Tehran water conveyance tunnel of Iran. Arab J Geosci 8(7):4833–4842CrossRefGoogle Scholar
  12. Dehkordi MS, Lazemi H, Shahriar K, Dehkordi MS (2015) Estimation of the rock load in non-squeezing ground condition using the post failure properties of rock mass. Geotech Geol Eng 33(4):1115–1128CrossRefGoogle Scholar
  13. Edelbro C (2008) Strength, fallouts and numerical modelling of hard rock masses. Luleå tekniska universitet, LuleåGoogle Scholar
  14. Edelbro C (2010) Different approaches for simulating brittle failure in two hard rock mass cases: a parametric study. Rock Mech Rock Eng 43:151–165CrossRefGoogle Scholar
  15. Hajiabdolmajid V, Kaiser P (2003) Brittleness of rock and stability assessment in hard rock tunneling. Tunn Undergr Space Technol 18:35–48CrossRefGoogle Scholar
  16. Hajiabdolmajid V, Kaiser P, Martin C (2002) Modelling brittle failure of rock. Int J Rock Mech Min Sci 39:731–741CrossRefGoogle Scholar
  17. Hassanpour J, Rostami J, Khamehchiyan M, Bruland A, Tavakoli H (2010) TBM performance analysis in pyroclastic rocks: a case history of Karaj water conveyance tunnel. Rock Mech Rock Eng 43:427–445CrossRefGoogle Scholar
  18. Hoek E, Brown ET (1997) Practical estimates of rock mass strength. Int J Rock Mech Sci Geom Abstr 34(8):1165–1187CrossRefGoogle Scholar
  19. Hoek E, Diederichs MS (2006) Empirical estimation of rock mass modulus. Int J Rock Mech Min Sci 43:203–215CrossRefGoogle Scholar
  20. Hoek E, Carranza-Torres C, Corkum B (2002) Hoek-Brown failure criterion-2002 edition. In: Proceedings of NARMS-Tac, pp 267–273Google Scholar
  21. Hustrulid W (1970) A comparison of laboratory cutting results and actual tunnel boring performance. Mining, Dept CSM, GoldenGoogle Scholar
  22. Muirhead I, Glossop L (1968) Hard rock tunnelling machines, institution of mining and metallurgy—transactions, 77, Sec A. Institution of Mining and Metallurgy, p A1–A21Google Scholar
  23. Sakurai S (1997) Lessons learned from field measurements in tunnelling. Tunn Undergr Sp Technol 12:453–460CrossRefGoogle Scholar
  24. Salimi A, Esmaeili M (2013) Utilising of linear and non-linear prediction tools for evaluation of penetration rate of tunnel boring machine in hard rock condition. Int J Min Miner Eng 4:249–264CrossRefGoogle Scholar
  25. Sahel Consulting Engineer (2009) Engineering geology report of Karaj–Tehran water conveyance tunnel (Lot 2), Tehran Regional Water AuthorityGoogle Scholar
  26. Schmertmann JH, Osterberg JO (1960) An experimental study of the development of cohesion and friction with axial strain in saturated cohesive soils. In: Research conference on shear strength of cohesive soils, ASCE, pp 643–694Google Scholar
  27. Singh M, Singh B, Choudhari J (2007) Critical strain and squeezing of rock mass in tunnels. Tunn Undergr Sp Technol 22:343–350CrossRefGoogle Scholar
  28. Teale R (1965) The concept of specific energy in rock drilling. Int J Rock Mech Mining Sci Geom Abstr 2(1):57–73CrossRefGoogle Scholar
  29. Walton G, Diederichs MS (2015) Dilation and post-peak behavior inputs for practical engineering analysis. Geotech Geol Eng 33:15–34CrossRefGoogle Scholar
  30. Wang L, Kang Y, Cai Z, Zhang Q, Zhao Y, Zhao H, Su P (2012) The energy method to predict disc cutter wear extent for hard rock TBMs. Tunn Undergr Space Technol 28:183–191CrossRefGoogle Scholar
  31. Zhang Q et al (2012) Modeling specific energy for shield machine by non-linear multiple regression method and mechanical analysis. In: Proceedings of the 2011 2nd international congress on computer applications and computational science, 2012. Springer, pp 75–80Google Scholar

Copyright information

© Springer Nature Switzerland AG 2018

Authors and Affiliations

  1. 1.Department of GeologyPayam Noor UniversityTehranIran
  2. 2.Department of Civil Engineering, Bafgh BranchIslamic Azad UniversityBafghIran

Personalised recommendations