Advertisement

Comparing the performance of traditional shear-wall and rocking shear-wall structures designed using the direct-displacement based design approach

  • Leikune F. AragawEmail author
  • Paolo M. Calvi
Original Research
  • 20 Downloads

Abstract

Reinforced concrete shear walls are widely used as lateral load resisting systems because of their favorable characteristics that include high strength, stiffness, ductility and energy dissipation. In most instances, these systems rely on the activation of a flexural mechanism at their base, where substantial damage is expected. Base-rocking systems have been proposed as a way to address this issue, mitigating severe structural damage while still limiting the seismic demands experienced by the structure. However, even when the base moment is limited, structural forces, moments and accelerations along the height of the structure can increase significantly because of higher mode effects. While this holds true for both traditional and rocking shear wall structures, past studies have suggested that rocking systems may be more prone to attract higher seismic demands. This article evaluates the performance of a set rocking shear wall structures against that of traditional reinforced concrete wall systems. The case study structures are analyzed via non-linear time history analyses, under a suite of spectrum compatible ground motions. The results of the numerical analyses confirm that while the overall performance of the rocking systems is superior to that of the “equivalent” traditional wall structures, they tend to be subjected to somewhat higher peak seismic demands.

Keywords

Base-rocking walls Precast walls Reinforced concrete walls Performance-based design Displacement-based design 

Notes

References

  1. Amaris AD (2002) Dynamic amplification of seismic moments and shear forces in cantilever walls. Master’s Dissertation, European School of Advanced Studies in Reduction of Seismic Risk (ROSE School), Pavia, ItalyGoogle Scholar
  2. Aragaw LF (2017) Floor response spectra in hybrid base-rocking and reinforced concrete wall buildings. Master’s Dissertation, University of Washington, Seattle, WA, USAGoogle Scholar
  3. Aragaw LF, Calvi PM (2018a) Earthquake-induced floor accelerations in base-rocking wall buildings. J Earthq Eng.  https://doi.org/10.1080/13632469.2018.1548393 CrossRefGoogle Scholar
  4. Aragaw LF, Calvi PM (2018b) Earthquake-induced floor accelerations in base-rocking wall buildings. J Earthq Eng.  https://doi.org/10.1080/13632469.2018.1548393 CrossRefGoogle Scholar
  5. ASCE (2010) Minimum Design Loads for Buildings and Other Structures. ASCE 7-10, American Society of Civil Engineers, Reston, VA, USAGoogle Scholar
  6. ASTM International (2016) ASTM A615/A615M-16 standard specification for deformed and plain carbon-steel bars for concrete reinforcement. ASTM International, West Conshohocken, PA, USAGoogle Scholar
  7. Belleri A, Schoettler MJ, Restrepo JI, Fleischman RB (2014) Dynamic behavior of rocking and hybrid cantilever walls in a precast concrete building. ACI Struct J 111(3):661CrossRefGoogle Scholar
  8. Carr AJ (2004) Ruaumoko 2D, inelastic dynamic analysis. Department of Civil Engineering, University of Canterbury, ChristchurchGoogle Scholar
  9. Cattanach A, Pampanin S (2008) 21st century precast: the detailing and manufacture of NZ’s first multi-storey PRESSS-Building. In NZ concrete industry conference, Rotorua, New ZealandGoogle Scholar
  10. Conley J, Sritharan S, Priestley MJN (2002) Precast seismic structural systems PRESSS-3: The five-story precast test building. Vol. 3–1: Wall direction response. Report Number: SSRP-99/19. San Diego, CAGoogle Scholar
  11. Fintel M (1995) Performance of buildings with shear walls in earthquakes of the last thirty years. PCI J 40(3):62–80CrossRefGoogle Scholar
  12. Gavridou S (2015) Shake table testing and analytical modeling of a full-scale, four-story unbonded post-tensioned concrete wall building. Doctoral Dissertation. University of California Los Angeles, CA, USAGoogle Scholar
  13. Holden T, Restrepo J, Mander JB (2003) Seismic performance of precast reinforced and prestressed concrete walls. J Struct Eng 129(3):286–296CrossRefGoogle Scholar
  14. Khanmohammadi M, Heydari S (2015) Seismic behavior improvement of reinforced concrete shear wall buildings using multiple rocking systems. Eng Struct 100:577–589CrossRefGoogle Scholar
  15. Kurama YC (2000) Unbonded post-tensioned precast concrete walls with supplemental viscous damping. ACI Struct J 97(4):648–658Google Scholar
  16. Kurama YC (2001) Simplified seismic design approach for friction-damped unbonded post-tensioned precast concrete walls. ACI Struct J 98(5):705–716.  https://doi.org/10.14359/10624 CrossRefGoogle Scholar
  17. Kurama YC (2002) Hybrid post-tensioned precast concrete walls for use in seismic regions. PCI J 47(5):36–59CrossRefGoogle Scholar
  18. Lehman DE, Turgeon JA, Birely AC, Hart CR, Marley KP, Kuchma DA, Lowes LN (2013) Seismic behavior of a modern concrete coupled wall. J Struct Eng 139(8):1371–1381CrossRefGoogle Scholar
  19. Mitchell D, DeVall RH, Saatcioglu M, Simpson R, Tinawi R, Tremblay R (1995) Damage to concrete structures due to the 1994 Northridge earthquake. Can J Civ Eng 22(2):361–377CrossRefGoogle Scholar
  20. Montejo LA, Kowalsky MJ (2007) CUMBIA—set of codes for the analysis of reinforced concrete members. CFL Technical Report No. IS-07 1Google Scholar
  21. Nakaki SD, Stanton JF, Sritharan S (1999) An overview of the PRESSS five-story precast test building. PCI J 44(2):26–39CrossRefGoogle Scholar
  22. Palermo A, Pampanin S, Carr AJ (2005) Efficiency of simplified alternative modelling approaches to predict the seismic response of precast concrete hybrid systems. In 2005 fib Symposium “Keep Concrete Attractive”. Budapest. HungaryGoogle Scholar
  23. Pampanin S, Kam W, Haverland G, Gardiner S (2011) Expectation meets reality: seismic performance of post-tensioned precast concrete southern cross endoscopy building during the 22nd Feb 2011 Christchurch earthquake. In NZ Concrete Industry Conference, Rotorua, New ZealandGoogle Scholar
  24. Panagiotou M, Restrepo JI (2009) Dual-plastic hinge design concept for reducing higher-mode effects on high-rise cantilever wall buildings. Earthq Eng Struct Dyn 38(12):1359–1380CrossRefGoogle Scholar
  25. Paulay T, Priestley MJN (1992) Seismic design of reinforced concrete and masonry buildings. Wiley.  https://doi.org/10.1002/978047017284
  26. Pennucci D, Calvi GM, Sullivan TJ (2009) Displacement-based design of precast walls with additional dampers. J Earthq Eng 13(S1):40–65CrossRefGoogle Scholar
  27. Perez FJ, Pessiki S, Sause R (2004) Seismic design of unbonded post-tensioned precast concrete walls with vertical joint connectors. PCI J 49(1):58–79CrossRefGoogle Scholar
  28. Perrone D, Calvi PM, Nascimbene R, Fischer EC, Magliulo G (2018) Seismic performance of non-structural elements during the 2016 Central Italy earthquake. Bull Earthq Eng.  https://doi.org/10.1007/s10518-018-0361-5 CrossRefGoogle Scholar
  29. Priestley MJN (1991) Overview of PRESSS research program. PCI J 36(4):50–57CrossRefGoogle Scholar
  30. Priestley MJN (1996) The PRESSS program—current status and proposed plans for phase III. PCI J 4(2):22–40CrossRefGoogle Scholar
  31. Priestley MJN (1998) Displacement-based approaches to rational limit states design of new structures. Keynote Address, 11th European Conference on Earthquake Engineering. Paris, FranceGoogle Scholar
  32. Priestley MJN (2002) Direct displacement-based design of precast/prestressed concrete buildings. PCI J 47(6):66–79CrossRefGoogle Scholar
  33. Priestley MJN, Grant DN (2005) Viscous damping in seismic design and analysis. J Earthq Eng 9(spec02):229–255CrossRefGoogle Scholar
  34. Priestley MJN, Sritharan S, Conley JR, Pampanin S (1999) Preliminary results and conclusions from the PRESSS five-story precast concrete test building. PCI J 44(6):42–67CrossRefGoogle Scholar
  35. Priestley MJN, Calvi GM, Kowalsky MJ (2007) Displacement-based seismic design of structures. IUSS Press, PaviaGoogle Scholar
  36. Qureshi IM, Warnitchai P (2016) Computer modeling of dynamic behavior of rocking wall structures including the impact-related effects. Adv Struct Eng 19(8):1245–1261.  https://doi.org/10.1177/1369433216642057 CrossRefGoogle Scholar
  37. Rahman AM, Restrepo JI (2000) Earthquake resistant precast concrete buildings: seismic performance of cantilever walls prestressed using unbonded tendons. Research Report 2000-5, Department of Civil Engineering, University of Canterbury, Christchurch, New ZealandGoogle Scholar
  38. Rahman MA, Sritharan S (2006) An evaluation of force-based design vs. direct displacement-based design of jointed precast post-tensioned wall systems. Earthq Eng Eng Vib 5(2):285–296CrossRefGoogle Scholar
  39. Rodriguez ME, Restrepo JI, Carr AJ (2002) Earthquake-induced floor horizontal accelerations in buildings. Earthq Eng Struct Dyn 31(3):693–718CrossRefGoogle Scholar
  40. Stanton J, Pizano-Battle V, Pizano-Thomen V (2003) Design of the Cala building using PRESSS technology. Concrete Structures in Seismic Regions: FIB 2003 SymposiumGoogle Scholar
  41. Sullivan TJ, Priestley MJN, Calvi GM (2008) Estimating the higher-mode response of ductile structures. J Earthq Eng 12(3):456–472CrossRefGoogle Scholar
  42. Twigden KM, Watkins J, Henry RS, Sritharan S (2013) Dynamic test evaluation of numerical models for unbonded post-tensioned concrete walls. In 2013 NZSEE annual conference. Wellington, New ZealandGoogle Scholar
  43. Welch DP (2016) Non-structural element considerations for contemporary performance-based earthquake engineering. Doctoral Dissertation, University of Pavia, Pavia, ItalyGoogle Scholar
  44. Wiebe L (2008) Mitigation of higher mode effects in self-centering walls by using multiple rocking sections. Master’s Dissertation, European school of advanced studies in reduction of seismic risk (ROSE School), Pavia, ItalyGoogle Scholar
  45. Wiebe L, Christopoulos C (2009) Mitigation of higher mode effects in base-rocking systems by using multiple rocking sections. J Earthq Eng 13(S1):83–108CrossRefGoogle Scholar
  46. Wiebe L, Christopoulos C (2015) A cantilever beam analogy for quantifying higher mode effects in multistorey buildings. Earthq Eng Struct Dyn 44:1697–1716CrossRefGoogle Scholar
  47. Wood SL, Wight JK, Moehle JP (1987) The 1985 Chile earthquake: observations on earthquake-resistant construction in Viña del Mar. University of Illinois Engineering Experiment Station. College of Engineering. University of Illinois at Urbana-ChampaignGoogle Scholar
  48. Zhang Z, Fleischman RB, Restrepo JI, Guerrini G, Nema A, Zhang D, Shakya U, Tsampras G, Sause R (2018) Shake-table test performance of an inertial force-limiting floor anchorage system. Earthq Eng Struct Dyn 47(10):1987–2011CrossRefGoogle Scholar

Copyright information

© Springer Nature B.V. 2019

Authors and Affiliations

  1. 1.Magnusson Klemencic AssociatesSeattleUSA
  2. 2.Department of Civil and Environmental EngineeringUniversity of WashingtonSeattleUSA

Personalised recommendations