Abstract
Estimation of geomechanical parameters is a challenging task in geotechnical engineering. This paper aims to estimate the geotechnical parameters of soil layers in the Tehran Metro line no. 7 based on the field measurement data. In this study, the design of experiment (DOE) method is utilized for estimation of the geotechnical parameters. The geotechnical parameters such as the modulus of elasticity (E), cohesion (c), and the internal friction angle (φ) are estimated using Taguchi’s DOE method and displacement-based back analysis. The results of the DOE experiments are examined by the analysis of range (ANORA) to improve the accuracy of the optimization. Results show that Taguchi’s DOE technique offers more effective and precise estimation of the geotechnical parameters than a displacement-based back analysis approach. Finally, the optimal combination of geotechnical parameters is proposed based on results analysis of Taguchi’s DOE and back analysis method. It is shown that the combination of the obtained geotechnical parameters from Taguchi’s DOE method is closer to the field measurement data.
Similar content being viewed by others
References
Asadollahpour E, Rahmannejad R, Asghari A, Abdollahipour A (2014) Back analysis of closure parameters of Panet equation and Burger’s model of Babolak water tunnel conveyance. Int J Rock Mech Min Sci 68:159–166
Azadeh A, Saberi M, Asadzadeh S, Khakestani M (2011) A hybrid fuzzy mathematical programming-design of experiment framework for improvement of energy consumption estimation with small data sets and uncertainty: the cases of USA, Canada, Singapore, Pakistan and Iran. Energy 36:6981–6992
Balki MK, Sayin C, Sarıkaya M (2016) Optimization of the operating parameters based on Taguchi method in an SI engine used pure gasoline, ethanol and methanol. Fuel 180:630–637
Cai M, Morioka H, Kaiser P, Tasaka Y, Kurose H, Minami M, Maejima T (2007) Back-analysis of rock mass strength parameters using AE monitoring data. Int J Rock Mech Min Sci 44:538–549
Casalino G, Curcio F, Minutolo FMC (2005) Investigation on Ti6Al4V laser welding using statistical and Taguchi approaches. J Mater Process Technol 167:422–428
Chang C-Y, Duncan JM (1970) Analysis of soil movement around a deep excavation. J Soil Mech Found Div 96:1655–1681
Chompu-inwai R, Jaimjit B, Premsuriyanunt P (2015) A combination of Material Flow Cost Accounting and design of experiments techniques in an SME: the case of a wood products manufacturing company in northern Thailand. J Clean Prod 108:1352–1364
Corporation SCE (2009) [5] Geotechnical and geology engineering investigation of Metro Line 7, East- West route
Daneshvar N, Khataee A, Rasoulifard M, Pourhassan M (2007) Biodegradation of dye solution containing Malachite Green: optimization of effective parameters using Taguchi method. J Hazard Mater 143:214–219
Dawud ER, Shakya AK (2014) HPLC-PDA analysis of ACE-inhibitors, hydrochlorothiazide and indapamide utilizing design of experiments. Arab J Chem. doi:10.1016/j.arabjc.2014.10.052
Delgado-Moreno L, Pena A, Mingorance M (2009) Design of experiments in environmental chemistry studies: example of the extraction of triazines from soil after olive cake amendment. J Hazard Mater 162:1121–1128
Elshennawy AK (2004) Quality in the new age and the body of knowledge for quality engineers. Total Qual Manag Bus Excel 15:603–614
Fakher A, Cheshomi A, Khamechiyan M (2007) The addition of geotechnical properties to a geological classification of coarse-grained alluvium in apediment zone. Q J Eng Geol Hydrogeol 40:163–174
Gioda G, Maier G (1980) Direct search solution of an inverse problem in elastoplasticity: identification of cohesion, friction angle and in situ stress by pressure tunnel tests. Int J Numer Meth Eng 15:1823–1848
Hisatake M, Hieda Y (2008) Three-dimensional back-analysis method for the mechanical parameters of the new ground ahead of a tunnel face. Tunn Undergr Space Technol 23:373–380
Hisataki M, Ito T (1985) Back analysis for tunnels by optimization method. In: International conference on numerical methods in geomechanics, pp 1301–1307
Houng J-Y, Liao J-H, Wu J-Y, Shen S-C, Hsu H-F (2007) Enhancement of asymmetric bioreduction of ethyl 4-chloro acetoacetate by the design of composition of culture medium and reaction conditions. Process Biochem 42:1–7
Jeon Y, Yang H (2004) Development of a back analysis algorithm using FLAC. Int J Rock Mech Min Sci 41:447–453
Jia Y, Chi S (2015) Back-analysis of soil parameters of the Malutang II concrete face rockfill dam using parallel mutation particle swarm optimization. Comput Geotech 65:87–96
Kavanagh KT, Clough RW (1971) Finite element applications in the characterization of elastic solids. Int J Solids Struct 7:11–23
Kitchen RR, Kubista M, Tichopad A (2010) Statistical aspects of quantitative real-time PCR experiment design. Methods 50:231–236
Knabe T, Datcheva M, Lahmer T, Cotecchia F, Schanz T (2013) Identification of constitutive parameters of soil using an optimization strategy and statistical analysis. Comput Geotech 49:143–157
Kondner RL (1963) A hyperbolic stress-strain formulation for sands. In: 2nd Pan-American Conference on Soil Mechanics and Foundation Engineering, Northwestern University, Sao Paulo, p 289
Kumar RS, Sureshkumar K, Velraj R (2015) Optimization of biodiesel production from Manilkara zapota (L.) seed oil using Taguchi method. Fuel 140:90–96
Kurmi M, Kumar S, Singh B, Singh S (2014) Implementation of design of experiments for optimization of forced degradation conditions and development of a stability-indicating method for furosemide. J Pharm Biomed Anal 96:135–143
Lai F-M, Tu C-W (2016) Optimizing the manufacturing parameters of carbon nanotubes stiffened speaker diaphragm using Taguchi method. Appl Acoust 113:81–88
Leu S-S, Adi TJW (2011) Probabilistic prediction of tunnel geology using a Hybrid Neural-HMM. Eng Appl Artif Intell 24:658–665
Li M, Yang F, Wan H, Fowler JW (2015) Simulation-based for lead time quotation. J Manuf Syst 37:362–374
Li S, Zhao H, Ru Z, Sun Q (2016) Probabilistic back analysis based on Bayesian and multi-output support vector machine for a high cut rock slope. Eng Geol 203:178–190
Mamourian M, Shirvan KM, Ellahi R, Rahimi A (2016) Optimization of mixed convection heat transfer with entropy generation in a wavy surface square lid-driven cavity by means of Taguchi approach. Int J Heat Mass Transf 102:544–554
Mercado V, El-Sekelly W, Zeghal M, Abdoun T (2015) Identification of soil dynamic properties through an optimization analysis. Comput Geotech 65:175–186
Miranda T, Dias D, Eclaircy-Caudron S, Correia AG, Costa L (2011) Back analysis of geomechanical parameters by optimisation of a 3D model of an underground structure. Tunn Undergr Space Technol 26:659–673
Miro S, König M, Hartmann D, Schanz T (2015) A probabilistic analysis of subsoil parameters uncertainty impacts on tunnel-induced ground movements with a back-analysis study. Comput Geotech 68:38–53
Ng EY, Ng WK (2006) Parametric study of the biopotential equation for breast tumour identification using ANOVA and Taguchi method. Med Biol Eng Compu 44:131–139
Oreste P (2005) Back-analysis techniques for the improvement of the understanding of rock in underground constructions. Tunn Undergr Space Technol 20:7–21
Ozcelik B, Erzurumlu T (2006) Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm. J Mater Process Technol 171:437–445
Rao RS, Kumar CG, Prakasham RS, Hobbs PJ (2008) The Taguchi methodology as a statistical tool for biotechnological applications: a critical appraisal. Biotechnol J 3:510–523
Rasoulifard MH, Akrami M, Eskandarian MR (2015) Degradation of organophosphorus pesticide diazinon using activated persulfate: optimization of operational parameters and comparative study by Taguchi’s method. J Taiwan Inst Chem Eng 57:77–90
Rechea C, Levasseur S, Finno R (2008) Inverse analysis techniques for parameter identification in simulation of excavation support systems. Comput Geotech 35:331–345
Romero-Villafranca R, Zúnica L, Romero-Zúnica R (2007) Ds-optimal experimental plans for robust parameter design. J Stat Plan Inference 137:1488–1495
Roy RK (2001) Design of experiments using the Taguchi approach: 16 steps to product and process improvement. Wiley, Hoboken
Rüfer A, Reschetilowski W (2012) Application of design of experiments in heterogeneous catalysis: Using the isomerization of n-decane for a parameter screening. Chem Eng Sci 75:364–375
Sakurai S, Takeuchi K (1983) Back analysis of measured displacements of tunnels. Rock Mech Rock Eng 16:173–180
Sánchez-López E et al (2016) PEGylated PLGA nanospheres optimized by design of experiments for ocular administration of dexibuprofen—in vitro, ex vivo and in vivo characterization. Colloids Surf B 145:241–250
Shanpo J, Youqing Z, Chensong Z (2012) Numerical solution to identification problems of material parameters in geotechnical engineering. Procedia Eng 28:61–65
Sharifzadeh M, Tarifard A, Moridi MA (2013) Time-dependent behavior of tunnel lining in weak rock mass based on displacement back analysis method. Tunn Undergr Space Technol 38:348–356
Siyal AA, Azizli KA, Man Z, Ullah H (2016) Effects of parameters on the setting time of fly ash based geopolymers using Taguchi method. Procedia Eng 148:302–307
Stavropoulou M, Xiroudakis G, Exadaktylos G (2010) Spatial estimation of geotechnical parameters for numerical tunneling simulations and TBM performance models. Acta Geotech 5:139–150
Sutcu M, Ozturk S, Yalamac E, Gencel O (2016) Effect of olive mill waste addition on the properties of porous fired clay bricks using Taguchi method. J Environ Manag 181:185–192
Taguchi G (1987) System of experimental design; engineering methods to optimize quality and minimize costs
Taguchi G, Konishi S (1987) Taguchi Methods: Orthogonal Arrays and Linear Graphs-Tools for Quality Engineering. American Supplier Institute, Center for Taguchi Methods
Taguchi K et al (2013) Effect of albumin on transthyretin and amyloidogenic transthyretin Val30Met disposition and tissue deposition in familial amyloidotic polyneuropathy. Life Sci 93:1017–1022
Tasirin SM, Kamarudin SK, Ghani JA, Lee K (2007) Optimization of drying parameters of bird’s eye chilli in a fluidized bed dryer. J food Eng 80:695–700
Tchognia JHN, Hartiti B, Ridah A, Ndjaka J-M, Thevenin P (2016) Application of Taguchi approach to optimize the sol–gel process of the quaternary Cu 2 ZnSnS 4 with good optical properties. Opt Mater 57:85–92
Terzaghi K, Peck RB (1967) Soil mechanics in engineering pratice
Tonon F, Amadei B, Pan E, Frangopol D (2001) Bayesian estimation of rock mass boundary conditions with applications to the AECL underground research laboratory. Int J Rock Mech Min Sci 38:995–1027
Tučková M, Harman R, Tuček P, Tuček J (2014) Design of experiment for hysteresis loops measurement. J Magn Magn Mater 368:64–69
Vardakos S, Gutierrez M, Xia C (2012) Parameter identification in numerical modeling of tunneling using the Differential Evolution Genetic Algorithm (DEGA). Tunn Undergr Space Technol 28:109–123
Wu C-H, Chen W-S (2006) Injection molding and injection compression molding of three-beam grating of DVD pickup lens. Sens Actuators A 125:367–375
Zhang K, Ping C, Rui B (2013) Rigorous back analysis of shear strength parameters of landslide slip. Trans Nonferrous Metals Soc China 23:1459–1464
Zhao C, Lavasan AA, Barciaga T, Zarev V, Datcheva M, Schanz T (2015) Model validation and calibration via back analysis for mechanized tunnel simulations–The Western Scheldt tunnel case. Comput Geotech 69:601–614
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kolivand, F., Rahmannejad, R. Estimation of geotechnical parameters using Taguchi’s design of experiment (DOE) and back analysis methods based on field measurement data. Bull Eng Geol Environ 77, 1763–1779 (2018). https://doi.org/10.1007/s10064-017-1042-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10064-017-1042-3