Advertisement

Numerical Modeling of Frictional Contact Between a Blunt Tool and Quasi-Brittle Rock

  • George Z. VoyiadjisEmail author
  • Yaneng Zhou
Original Paper
  • 103 Downloads

Abstract

Frictional contact is an important component of rock cutting with a blunt cutter. There has been a gap in knowledge of frictional contact between experimental tests conducted on quasi-brittle rocks and previous numerical and analytical analyses on elastoplastic rocks. The average contact stress between a sliding wear flat and a rock is generally overestimated in previous studies without considering material length scales. This study analyzes the contact stress using an elasto-plastic-damage model that accounts for the material length scales of quasi-brittle materials. The constitutive model is developed for quasi-brittle materials by incorporating fracture energy, and it is implemented in the commercial finite element software ABAQUS as a user-defined material model. The implemented constitutive model is verified under uniaxial tension and compression. The average contact stress in frictional contact is mainly governed by a dimensionless elastoplastic parameter \( \eta \) for an elastoplastic rock, while it is predominantly governed by two dimensionless parameters: an elastoplastic parameter \( \eta \) and a brittleness number \( \xi \) for a quasi-brittle rock. The dimensionless elastoplastic parameter \( \eta \) contrasts the magnitude of a characteristic elastic contact stress to the yield strength of a material, and the brittleness number \( \xi \) is the ratio of a geometrical length scale to a material length scale. The tool–rock interface can be approximately divided into an elastic zone and a damage process zone. The contact stress generally increases in the elastic zone and then decreases in the damage process zone towards the tip of the slider. The average contact stress generally increases with the dimensionless elastoplastic parameter \( \eta \) and then levels off at a limit value, and it generally decreases with the brittleness number \( \xi \). This study reduces the gap in previous studies to some extent by introducing the brittleness number \( \xi \) in frictional contact. The current numerical results of the average contact stress are generally consistent with typical experimental results conducted on quasi-brittle rocks, despite limitations in the finite element modeling.

Keywords

Frictional contact Contact stress Brittleness Material length scale Rock damage Elasto-plastic-damage model 

Notes

Acknowledgements

This work was funded by the Center for GeoInformatics (C4G) at the Louisiana State University. The second author acknowledges gratitude to Professor Emmanuel Detournay at the University of Minnesota for the benefit of stimulating discussions that inspired this work.

References

  1. Abu Al-Rub RK, Kim S-M (2010) Computational applications of a coupled plasticity-damage constitutive model for simulating plain concrete fracture. Eng Fract Mech 77(10):1577–1603CrossRefGoogle Scholar
  2. Abu Al-Rub RK, Voyiadjis GZ (2009) Gradient-enhanced coupled plasticity-anisotropic damage model for concrete fracture: computational aspects and applications. Int J Damage Mech 18(2):115–154CrossRefGoogle Scholar
  3. Adachi J (1996) Frictional contact in rock cutting with blunt tools. MS thesis, University of Minnesota, Minneapolis, MNGoogle Scholar
  4. Alehossein H, Detournay E, Huang H (2000) An analytical model for the indentation of rocks by blunt tools. Rock Mech Rock Eng 33(4):267–284CrossRefGoogle Scholar
  5. Almenara R (1992) Investigation of the cutting process in sandstones with blunt PDC cutters. Ph.D. thesis, Imperial College, London, UKGoogle Scholar
  6. Almenara R, Detournay E (1992) Cutting experiments in sandstones with blunt PDC cutters. In: ISRM symposium: Eurock 92, Chester, UKGoogle Scholar
  7. Amri M, Pelfrene G, Jahangir E, Tijani M, Sellami H (2018) Numerical and analytical study of rate effects on drilling forces under bottomhole pressure. Int J Rock Mech Min Sci 110:189–198CrossRefGoogle Scholar
  8. Borri-Brunetto M, Carpinteri A, Invernizzi S (2003) Characterization and mechanical modeling of the abrasion properties of sintered tools with embedded hard particles. Wear 254(7–8):635–644CrossRefGoogle Scholar
  9. Carpinteri A, Invernizzi S (2005) Numerical analysis of the cutting interaction between indenters acting on disordered materials. Int J Fract 131(2):143–154CrossRefGoogle Scholar
  10. Carpinteri A, Chiaia B, Invernizzi S (2004) Numerical analysis of indentation fracture in quasi-brittle materials. Eng Fract Mech 71(4–6):567–577CrossRefGoogle Scholar
  11. Cervera M, Chiumenti M (2009) Size effect and localization in J2 plasticity. Int J Solids Struct 46(17):3301–3312CrossRefGoogle Scholar
  12. Cervera M, Chiumenti M, Agelet de Saracibar C (2004) Softening, localization and stabilization: capture of discontinuous solutions in J2 plasticity. Int J Numer Anal Meth Geomech 28(5):373–393CrossRefGoogle Scholar
  13. Challen JM, Oxley PLB (1979) An explanation of the different regimes of friction and wear using asperity deformation models. Wear 53(2):229–243CrossRefGoogle Scholar
  14. Cicekli U, Voyiadjis GZ, Abu Al-Rub RK (2007) A plasticity and anisotropic damage model for plain concrete. Int J Plast 23(10–11):1874–1900CrossRefGoogle Scholar
  15. Detournay E, Defourny P (1992) A phenomenological model for the drilling action of drag bits. Int J Rock Mech Min Sci Geomech Abstr 29(1):13–23CrossRefGoogle Scholar
  16. Geoffroy H, Minh DN, Bergues J, Putot C (1998) Frictional contact on cutters wear flat and evaluation of drilling parameters of a PDC bit. In: SPE/ISRM rock mechanics in petroleum engineering. Society of Petroleum Engineers, Trondheim, NorwayGoogle Scholar
  17. Gerbaud L, Menand S, Sellami H (2006) PDC bits: all comes from the cutter rock interaction. In: IADC/SPE drilling conference, Miami, FLGoogle Scholar
  18. Gladwell GM (1980) Contact problems in the classical theory of elasticity. Sijthoff & Noordhoff, Alphen aan den RijnCrossRefGoogle Scholar
  19. Glowka D (1989) Use of single-cutter data in the analysis of PDC bit designs: part 1—development of a PDC cutting force model. J Pet Technol 41:797–799CrossRefGoogle Scholar
  20. Hibbitt HD, Karlsson BI, Sorensen P (2001) ABAQUS/standard user’s manual. Hibbitt, Karlsson & Sorensen, Inc., PawtucketGoogle Scholar
  21. Hillerborg A (1985) The theoretical basis of a method to determine the fracture energy Gf of concrete. Mater Struct 18(4):291–296CrossRefGoogle Scholar
  22. Huang H, Detournay E (2008) Intrinsic length scales in tool–rock interaction. Int J Geomech 8:39–44CrossRefGoogle Scholar
  23. Huang H, Detournay E (2013) Discrete element modeling of tool–rock interaction II: rock indentation. Int J Numer Anal Methods Geomech 37(13):1930–1947CrossRefGoogle Scholar
  24. Huang H, Lecampion B, Detournay E (2013) Discrete element modeling of tool–rock interaction I: rock cutting. Int J Numer Anal Meth Geomech 37(13):1913–1929CrossRefGoogle Scholar
  25. Johnson KL (1970) The correlation of indentation experiments. J Mech Phys Solids 18(2):115–126CrossRefGoogle Scholar
  26. Johnson KL (1987) Contact mechanics. Cambridge University Press, LondonGoogle Scholar
  27. Kupfer H, Hilsdorf HK, Rusch H (1969) Behavior of concrete under biaxial stresses. ACI J 66(8):656–666Google Scholar
  28. Labuz J, Dai S (2000) Residual strength and fracture energy from plane-strain testing. J Geotech Geoenviron Eng 126(10):882–889CrossRefGoogle Scholar
  29. Lee J, Fenves GL (1998) Plastic-damage model for cyclic loading of concrete structures. J Eng Mech 124(8):892–900CrossRefGoogle Scholar
  30. Lubliner J, Oliver J, Oller S, Onate E (1989) A plastic-damage model for concrete. Int J Solids Struct 25(3):299–326CrossRefGoogle Scholar
  31. Marck J, Detournay E (2016) Influence of rotary-steerable-system design on borehole spiraling. SPE J 21(01):293–302CrossRefGoogle Scholar
  32. Murray YD (2007) User manual for LS-DYNA concrete material model 159. Federal Highway Administration, McleanGoogle Scholar
  33. Oliver J, Cervera M, Oller S, Lubliner J (1990) Isotropic damage models and smeared crack analysis of concrete. In: 2nd International conference on computer aided analysis and design of concrete structures, Zell am See, Austria, pp 945–957Google Scholar
  34. Prandtl L (1921) Hauptaufsätze: Über die eindringungsfestigkeit (härte) plastischer baustoffe und die festigkeit von schneiden. ZAMM Z Angew Math Mech 1(1):15–20CrossRefGoogle Scholar
  35. Richard T, Germay C, Detournay E (2007) A simplified model to explore the root cause of stick–slip vibrations in drilling systems with drag bits. J Sound Vib 305(3):432–456CrossRefGoogle Scholar
  36. Richard T, Dagrain F, Poyol E, Detournay E (2012) Rock strength determination from scratch tests. Eng Geol 147:91–100CrossRefGoogle Scholar
  37. Rostamsowlat I (2018) Effect of cutting tool properties and depth of cut in rock cutting: an experimental study. Rock Mech Rock Eng 51(6):1715–1728CrossRefGoogle Scholar
  38. Rostamsowlat I, Akbari B, Evans B (2018a) Analysis of rock cutting process with a blunt PDC cutter under different wear flat inclination angles. J Pet Sci Eng 171:771–783CrossRefGoogle Scholar
  39. Rostamsowlat I, Richard T, Evans B (2018b) Experimental investigation on the effect of wear flat inclination on the cutting response of a blunt tool in rock cutting. Acta Geotech.  https://doi.org/10.1007/s11440-018-0674-1 Google Scholar
  40. Rostamsowlat I, Richard T, Evans B (2018c) An experimental study of the effect of back rake angle in rock cutting. Int J Rock Mech Min Sci 107:224–232CrossRefGoogle Scholar
  41. Saucedo L, Yu RC, Gonzalo R (2012) Fully-developed FPZ length in quasi-brittle materials. Int J Fract 178(1–2):97–112CrossRefGoogle Scholar
  42. Shen B, Stephansson O (1994) Modification of the G-criterion for crack propagation subjected to compression. Eng Fract Mech 47(2):177–189CrossRefGoogle Scholar
  43. Shi G, Voyiadjis GZ (1997) A new free energy for plastic damage analysis. Mech Res Commun 24(4):377–383CrossRefGoogle Scholar
  44. Tao X, Phillips DV (2005) A simplified isotropic damage model for concrete under bi-axial stress states. Cem Concr Compos 27(6):716–726CrossRefGoogle Scholar
  45. Taqieddin ZN, Voyiadjis GZ (2009) Elastic plastic and damage model for concrete materials: part II—implementation and application to concrete and reinforced concrete. Int J Struct Chang Solids 1(1):187–209Google Scholar
  46. Voyiadjis GZ, Abu-Lebdeh TM (1994) Plasticity model for concrete using the bounding surface concept. Int J Plast 10(1):1–21CrossRefGoogle Scholar
  47. Voyiadjis GZ, Taqieddin ZN (2009) Elastic plastic and damage model for concrete materials: part I—theoretical formulation. Int J Struct Chang Solids 1(1):31–59Google Scholar
  48. Voyiadjis GZ, Taqieddin ZN, Kattan PI (2008) Anisotropic damage—plasticity model for concrete. Int J Plast 24(10):1946–1965CrossRefGoogle Scholar
  49. Voyiadjis GZ, Taqieddin ZN, Kattan PI (2009) Theoretical formulation of a coupled elastic–plastic anisotropic damage model for concrete using the strain energy equivalence concept. Int J Damage Mech 18(7):603–638CrossRefGoogle Scholar
  50. Wu JY, Li J, Faria R (2006) An energy release rate-based plastic-damage model for concrete. Int J Solids Struct 43(3–4):583–612CrossRefGoogle Scholar
  51. Zhang J, Li J (2014) Elastoplastic damage model for concrete based on consistent free energy potential. Sci China Technol Sc 57(11):2278–2286CrossRefGoogle Scholar
  52. Zhou Y (2017a) The applicability of correspondence rule with inclined load. Rock Mech Rock Eng 50(1):233–240CrossRefGoogle Scholar
  53. Zhou Y (2017b) Misinterpretation of friction as fracture in shallow scratch tests with classical and universal size effect laws. Eng Fract Mech 184:14–21CrossRefGoogle Scholar
  54. Zhou Y, Detournay E (2014) Analysis of the contact forces on a blunt PDC bit. In: 48th US rock mechanics/geomechanics symposium, Minneapolis, MNGoogle Scholar
  55. Zhou Y, Detournay E (2019) Elastoplastic model of a blunt rigid tool sliding on rock (in preparation)Google Scholar
  56. Zhou Y, Lin J-S (2013) On the critical failure mode transition depth for rock cutting. Int J Rock Mech Min Sci 62:131–137CrossRefGoogle Scholar
  57. Zhou Y, Zhang W, Gamwo IK, Lin J-S (2017) Mechanical specific energy versus depth of cut in rock cutting and drilling. Int J Rock Mech Min Sci 100:287–297CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Austria, part of Springer Nature 2019

Authors and Affiliations

  1. 1.Department of Civil and Environmental Engineering, Center for GeoInformatics C4G and Computational Solid Mechanics LaboratoryLouisiana State UniversityBaton RougeUSA

Personalised recommendations