Effect of laser heating on nanoscale wear of DLC thin films in an air environment

  • Norio Tagawa
  • Hiroshi Tani
  • Shinji Koganezawa
  • Renguo Lu
Technical Paper
  • 3 Downloads

Abstract

In this study, fundamental experiments were conducted to understand the wear and related degradation characteristics of an ultra-thin DLC overcoat subjected to laser heating in an air environment, using a pin-on-disk tester. The experiments were conducted using DLC-coated glass pins and actual magnetic disks without a lubricant film. The differences in the wear and degradation characteristics of a DLC overcoat on the pin and disk surfaces, both with and without laser heating, were investigated after wear tests were performed, primarily through Raman spectroscopy. We found that the wear on DLC films became greater with laser heating, while the friction coefficients between the pin and magnetic disk became markedly smaller. This is because the wear observed in this experiment was predominantly due to a wear mechanism that is based on tribo-chemical oxidation.

Notes

Acknowledgment

This work was supported in part by Kansai University Grant-in-Aid for the Promotion and Upgrading of Education and Research 2016, and MEXT KAKENHI Grant Number 15H02216.

References

  1. Challener WA, Peng C, Itagi AV, Karns D, Peng W, Peng Y, Yang XM, Zhu X, Gokemeijer NJ, Hsia YT, Ju G, Rottmayer RE, Seigler MA, Gage EC (2009) Heat-assisted magnetic recording by a near-field transducer with efficient optical energy transfer. Nat Photon 3(4):220–224CrossRefGoogle Scholar
  2. Chen XY, Shen J, Zhou M (2016) Rapid fabrication of a four-layer PMMA-based microfluidic chip using CO2-laser micromachining and thermal bonding. J Micromech Microeng 26(10):107001CrossRefGoogle Scholar
  3. Kasai PH, Tang WT, Wheeler P (1991) Degradation of perfluoropolyethers catalyzed by aluminum oxide. Appl Surf Sci 51:201–211CrossRefGoogle Scholar
  4. Kiely JD, Jones PM, Yang Y, Brand JL, Anaya-Dufresne M, Fletcher PC, Zavaliche F, Toivola Y, Duda JC, Johnson MT (2017) Write-induced head contamination in heat-assisted magnetic recording. IEEE Trans Magn 53(2):3300307CrossRefGoogle Scholar
  5. Liu J, Stirniman MJ, Gui J (2003) Catalytic decomposition of perfluoropolyether lubricants. IEEE Trans Magn 39:749–753CrossRefGoogle Scholar
  6. Marchon B, Olsen T (2009) Magnetic spacing trends: from LMR to PMR and beyond. IEEE Trans Magn 45(10):3608–3611CrossRefGoogle Scholar
  7. Marchon B, Heiman N, Khan MR (1990) Evidence for tribo-chemical wear on amorphous carbon thin film. IEEE Trans Magn 26(1):168–170CrossRefGoogle Scholar
  8. Mate CM, Dai Q, Payne RN, Knigge BE, Baumgart P (2005) Will the numbers add up for sub-7-nm magnetic spacing? Future metrology issues for disk drive lubricants, overcoats, and topographies. IEEE Trans Magn 41(2):626–631CrossRefGoogle Scholar
  9. Matthes LM, Brunner R, Knigge B, Talke FE (2015) Head wear of thermal flying height control sliders as a function of bonded lubricant ratios, temperature, and relative humidity. Tribol Lett 60:39.  https://doi.org/10.1007/s11249-015-0614-2 CrossRefGoogle Scholar
  10. Matthes LM, Spada FE, Ovcharenko A, Knigge B, Talke FE (2017) Effect of head-disk interface biasing and relative humidity on wear of thermal flying height control sliders. Tribol Lett 65:44.  https://doi.org/10.1007/s11249-017-0828-6 CrossRefGoogle Scholar
  11. Miyaji G, Miyazaki K (2007) Nanoscale ablation on patterned diamond-like carbon film with femtosecond laser pulses. Appl Phys Lett 91(12):123102CrossRefGoogle Scholar
  12. Tagawa N, Andoh H, Tani H (2009) Study on lubricant depletion induced by laser heating in thermally assisted magnetic recording systems: effect of lubricant thickness and bonding ratio. Tribol Lett 37(2):411–418CrossRefGoogle Scholar
  13. Tagawa N, Tani H, Koganezawa S (2014) Degradation of carbon overcoat subjected to laser heating in an inert gas environment in thermally assisted magnetic recording. IEEE Trans Magn 50(11):3302404CrossRefGoogle Scholar
  14. Tagawa N, Tani H, Asada H, Lu R, Koganezawa S (2017) Decomposition of perfluoropolyether lubricant on air bearing surfaces during heat-assisted magnetic recording. IEEE Trans Magn 53(3):3301505Google Scholar
  15. Tani H, Tomita J, Koganezawa S, Tagawa N (2014) Effect of vapor lubrication on head-disk clearance and slider wear in inert gas environments. Proceedings of the ASME 2014 conference on information storage and processing systems, ISPS2014-6931, June 23–24, Santa Clara, CAGoogle Scholar
  16. Tani H, Koganezawa S, Tagawa N (2016) Thermal behavior of frictional properties on ultra-thin perfluoropolyether lubricant film. Tribol Online 11(1):1–12CrossRefGoogle Scholar
  17. Waltman RJ, Deng H, Wang GJ, Zhu H, Tyndall GW (2010) The effect of PFPE film thickness and molecular polarity on the pick-up of disk lubricant by a low-flying slider. Tribol Lett 39:211–219CrossRefGoogle Scholar
  18. Wang Y, Wei X, Tsui KL (2014) Chow, T.W.S., Tribological degradation of head–disk interface in hard disk drives under accelerated wear condition. IEEE Trans Magn 50(3):3301007Google Scholar
  19. Yang Y, Li X, Stirniman M, Yan X, Huang F, Zavaliche F, Wang H, Huang J, Tang H, Jones PM, Kiely JD, Brand JI (2015) Head-disk lubricant transfer and deposition during heat-assisted magnetic recording write operations. IEEE Trans Magn 51(11):3300604Google Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringKansai UniversitySuitaJapan

Personalised recommendations