# A numerical model for the development of the morphology of disperse blends in complex flow

- 156 Downloads

## Abstract

The aim of this study is to develop a constitutive model for disperse blends applicable in complex flows and to cast this model in a finite element framework. As the number of droplets in realistic conditions is extremely large, it is computationally intractable to model all droplets individually. Droplet populations are modeled that have macroscopically averaged morphological properties. These properties are the droplet stretch ratio, the unstretched droplet radius, the orientation vector, and the number of droplets per unit volume. The evolution equations of these properties vary based on the morphological state transitions. The current model describes the morphology evolution in complex geometries, assuming Newtonian mixture constituents and monodisperse droplet populations. The numerical model has been validated for simple shear flow. Results are discussed for Poiseuille flow and the eccentric cylinder flow.

## Keywords

Polymer blends Numerical Droplet morphology## Introduction

An important class of materials is polymer blends. The majority of polymer blends are immiscible, because mixing long polymer chains is thermodynamically unfavorable. Consequently, many polymer blends have a multiphase structure. There is a huge variety of structures that can be produced, such as dispersed droplets (dispersive blends), co-continuous blends, and fibril-like structures. In this work, we focus on modeling dispersive blends. Dispersive mixing is an often used method in industry, not only in polymer blending, but also in, for example, food processing and the pharmaceutical industry. To obtain the desired material properties, it is crucial to be able to control the droplet size of the disperse phase. Depending on the emulsion properties and the processing history, the droplets can undergo changes as a result of deformation, orientation, breakup, and coalescence.

Many authors have contributed to the modeling and experimental work of the deformation and breakup of single droplets (see for example Minale (2010)). The case of small deformation and Newtonian liquids has been investigated by Taylor (1932) and Taylor (1934). Tomotika (1935) analytically investigated the breakup of an infinitely long viscous filament embedded within a matrix of another viscous liquid. This work was expanded upon by Mikami et al. (1975) and Khakhar and Ottino (1987). Cox (1969) described the deformation of an ellipsoidal droplet in a general time-dependent flow field. Doi and Ohta (1991) follow the approach of the influential paper of Batchelor (1970) by describing the morphology in terms of an interface tensor, quantifying the expansion, and orientation of complex interfaces under the influence the macroscopic velocity field and the interfacial tension. Another model describing the morphology with a shape tensor has been developed by Maffettone and Minale (1998). Ellipsoidal drop shape predictions have been verified by three-dimensional visualization by Guido and Greco (2001). Both the Doi-Ohta model and the Maffetone and Minale model have been generalized using the generic formalism from Grmela and Öttinger (1997), applied on immiscible blends by Grmela et al. (2001). Using the generic formalism, Edwards et al. (2003) developed a range of rheological models that obey certain physical constraints, such as volume conservation of the disperse phase in dispersive polymer blends. Influential experimental work on the breakup conditions has been carried out by Grace (1982). Further experimental investigations were carried out by Bentley and Leal (1986a, b), Stone et al. (1986), Grizzuti and Bifulco (1997), and Vinckier et al. (1997). Excellent reviews on these topics have been given by Stone (1994) and Tucker and Moldenaers (2002). Development of a model to describe the morphology of immiscible Newtonian blends undergoing morphological changes from the initial structure to the final structure after deformation, breakup and coalescence has been done by Peters et al. (2001) and Almusallam et al. (2004).

The objective of this study is to develop a phenomenological model for predicting the morphology evolution of disperse blends in complex flows. Our starting point is the constitutive dispersive blend model of Peters et al. (2001). This model has been shown to be very successful for describing dispersive blend morphology in shear flow. However, this model has discontinuous solutions in time and space, hence is not attractive for implementation in a finite element formulation. The aim of this work is to extend this model, introduce smoothed field variables and apply our methodology for complex flow problems.

## Phenomenological blend model

### Droplet morphology

*μ*

_{m}is the dynamic viscosity of the matrix phase, \(\dot {\gamma }\) is the shear rate,

*R*

_{0}is the radius of the unstretched droplet and

*σ*is the interfacial tension between the two fluid phases. Another important dimensionless quantity for describing this process is the viscosity ratio

*λ*, as given by:

*μ*

_{d}is the dynamic viscosity of the droplet phase.

_{crit}above which the droplet becomes unstable. This critical capillary number depends on the viscosity ratio and the flow type. Grace (1982) has measured this relation for shear flow and planar extensional flow. For simple shear flow, this is given by De Bruijn (1989):

_{crit}decreases with increasing volume fractions. However, it was also observed that the Grace curve, which was determined for breakup of single droplets, can be used if the matrix viscosity

*μ*

_{m}is replaced by an effective matrix viscosity. This makes sense, because in a (concentrated) emulsion, a droplet is not surrounded by pure matrix fluid, but by matrix fluid containing a large number of other droplets. The effective matrix viscosity is given by Choi and Schowalter (1975):

*ϕ*is the volume fraction of the droplet phase in the total fluid mixture.

Droplets break up via mainly four mechanisms (Jansen et al. 2001; Van Puyvelde and Moldenaers 2005). The first one is necking (also called waist-thinning or binary breakup). In this case, a slightly deformed droplet simply splits up into two daughter droplets. The second breakup mechanism is filament breakup (also called capillary breakup), where a droplet has been stretched into a long thin filament and breaks up into a line of multiple daughter droplets under the influence of the Rayleigh-Plateau instability. The third breakup mechanism is end-pinching, where the ends of a filament break off as new daughter droplets, which can happen due to collision with neighboring droplets or when the flow is stopped at intermediate aspect ratios of the deformed droplet. The fourth breakup mechanism is tip-streaming, where the ends of a deformed droplet become cusp-like and small droplets are ejected from the tips. This occurs due to Marangoni stresses that arise as a result of a non-uniform surfactant distribution. In this work, only the first two mechanisms are considered (necking and filament breakup). Marangoni stresses do not occur, because we study only single populations of clean drops, which do not exhibit end-pinching and tip-streaming (Bazhlekov et al. 2006; Janssen and Anderson 2008).

*h*

_{crit}, as given by Chesters (1991):

*A*

_{h}is the Hamaker constant and

*R*

_{eq}is the equivalent radius of the two differently sized droplets. In this work, it is assumed that

*R*

_{eq}=

*R*

_{0}. The analysis on the coalescence probability by Janssen (1993) shows that coalescence occurs mostly in regions with low Ca, because that is needed to allow enough interaction time for the film to drain completely, though at too low Ca, the probability of collisions occurring is very low, then nothing happens with the droplets.

### Morphological quantities and state changes

Several approaches can be followed to describe the droplet structure in blends, such as sharp interface models, diffuse interface models and macroscopic models. In the first two types of models, the droplet interfaces are tracked directly, but this quickly becomes computationally intractable as the number of droplets becomes as large as what is seen in industrial blends. In the case of macroscopic models, a microstructural model of the droplet morphology development is used and translated to a number of macroscopically averaged quantities.

We describe the blend structure using a macroscopic model and use the model of Peters et al. (2001) as a starting point. This model describes the blend structure phenomenologically and couples this to a stress contribution. We focus on the part describing the blend structure. It has been demonstrated to be very successful for describing the droplet structure in shear flow. However, the solutions are discontinuous in time and space, so it cannot easily be implemented in a finite element formulation in this form. Therefore, we introduce smoothed field variables that can be solved in a complex flow geometry. In every point in space * x*, there is a population of droplets with macroscopically averaged quantities. These quantities are the stretch ratio

*β*(

*), unstretched droplet radius*

**x***R*

_{0}(

*), orientation vector*

**x***(*

**m***) and number of droplets per unit volume*

**x***N*

_{d}(

*). The stretch ratio is defined as the length of the major axis of an extended ellipsoid droplet divided by the diameter of the unstretched droplet. The orientation vector is described using the*

**x***tensor, which is defined as the contravariant decomposition of the*

**b***tensor, with*

**c***=*

**c***⋅*

**b**

**b**^{T}(Hütter et al. 2018). The tensor

*is governed by a Giesekus model. The orientation vector*

**c***is defined as the eigenvector corresponding to the largest eigenvalue of the*

**m***tensor. Peters et al. (2001) use the Finger tensor*

**c***instead of*

**B***and the deformation gradient tensor*

**c***instead of*

**F***. Our definition for the orientation vector*

**b***is similar to how Peters et al. (2001) define it as the eigenvector corresponding to the largest eigenvalue of the Finger tensor*

**m***, which gives the direction in which the background flow field has the largest deformation.*

**B***R*that is determined by conservation of volume:

*μ*

_{e}, the macroscopically averaged unstretched droplet radius

*R*

_{0}and the effective shear rate, defined by:

*= (∇*

**L***)*

**u**^{T}, with

*the velocity field. When Ca < Ca*

**u**_{crit}, droplet breakup cannot occur. In this regime, the morphology is described by coalescence. The rate of coalescence depends on the volume fraction of the droplet phase and the shear rate. When Ca is very large (Ca ≥

*κ*Ca

_{crit}), the droplet first deforms into a long thin filament. The parameter

*κ*depends on the flow type and has the value 2 for shear flow and 5 for planar elongational flow. For complex flows, the value for

*κ*will be between 2 and 5. For simplicity, we assume

*κ*= 2 for all cases in this work. This is valid for the cases of simple shear and Poiseuille flow. However, this assumption is not valid for complex flow problems with a significant extensional contribution, such as an eccentric cylinder flow problem. This topic will be investigated in a subsequent paper. When the filament radius

*R*reaches a critical filament radius (

*R*≤

*R*

_{crit}), the filament breaks up via capillary breakup. The critical filament radius is given by Tjahjadi and Ottino (1991):

*α*

_{0}is the initial disturbance amplitude (which eventually grows sufficiently large to make the filament unstable),

*λ*

_{e}=

*μ*

_{d}/

*μ*

_{e}is the effective viscosity ratio and

*is the orientation vector, which is calculated as the eigenvector corresponding to the largest eigenvalue of*

**m***.*

**c***α*

_{0}is of the order \(\mathcal {O}(10^{-9}) \) (Janssen 1993). Lastly, the intermediate Ca regime, where Ca

_{crit}≤Ca <

*κ*Ca

_{crit}, is described by necking.

### Morphology evolution equations

*β*, the unstretched droplet radius

*R*

_{0}, and the

*tensor (from which the orientation vector is derived). The number of droplets*

**b***N*

_{d}can be derived from the droplet radius via conservation of volume. The evolution equations are given by:

*tensor is given by Hütter et al. (2018):*

**b***instead of the conformation tensor. We define the*

**b***tensor in this way to prevent it from growing indefinitely. With this method,*

**b***will eventually relax towards a certain steady value, depending on the parameters*

**b***τ*

_{G}and

*α*

_{G}. For

*τ*

_{G}→

*∞*in Eq. 13,

*goes to the deformation gradient tensor*

**b***and*

**F***goes to the Finger tensor*

**c***. The functions*

**B***f*

_{1}and

*f*

_{2}vary based on the mechanism of morphological change.

*ϕ*the volume fraction of the disperse phase in the blend,

*τ*

_{c}a numerical smoothing parameter and

*f*

_{2}is derived by Peters et al. (2001), using the calculation of the droplet radius during coalescence from Janssen (1993). The value of

*β*

^{+}is the value that the stretch ratio

*β*would discontinuously jump to according to the Peters model. In that model, the stretch ratio is not directly used in the stress calculation, but an intermediate step of calculating an effective stretch ratio

*β*

_{eff}via an ODE of the form of Eq. 14 is performed. This step smoothes the discontinuous jump in time. We follow the same approach but apply the smoothing step directly to the stretch ratio field variable

*β*itself. This smoothing in time effectively also smoothes discontinuous jumps along the streamline direction. However, there is no smoothing of discontinuous jumps in crosswind direction, as is seen in the results obtained for Poiseuille flow in “Poiseuille flow".

*τ*

_{n}a numerical smoothing parameter and

*f*

_{2}is taken from the Peters model and the smoothing step for the stretch ratio with

*f*

_{1}as given by the right-hand side term of Eq. 10 is similar to the case of coalescence as given by Eq. 14.

_{ext}is the extensional capillary number, as it is calculated based on

**D***(which is a measure of extension) instead of the equivalent shear rate \(\dot {\gamma } \). Since a stretching droplet does not change its undeformed radius*

**: mm***R*

_{0}, we have set

*f*

_{2}= 0. The expression for

*f*

_{1}is derived by Stegeman et al. (1999). In the case of shear flow, the droplet will initially be oriented in the direction of highest shear (

**D***is maximal). As the shear is maintained, the droplet rotates away from this direction and*

**: mm**

**D***decreases to a very small value, depending on*

**: mm***α*

_{G}.

*τ*

_{b}a numerical smoothing parameter and

*β*and

*R*

_{0}are smoothed as explained for Eq. 14. Equation 26 is important for the selection of the smoothing parameter. When smoothing is performed too slowly (i.e., with a too large value for the smoothing parameter

*τ*

_{b}), the capillary number evolves significantly differently, which means the droplet population will experience the morphological changes of filament stretching, filament breakup, necking, and coalescence very differently. Therefore, the smoothing parameter is chosen not too large. In this work, we set it to be at least one order of magnitude larger than the numerical time step but not much higher.

Earlier, it was mentioned that **D*** : mm* can go toward a very small value. If this happens, then

*R*

_{crit}and \({R}_{0}^{+} \) will go to infinity (see Eqs. 9 and 28). However, even if

*R*

_{crit}is large but finite, there is still the issue that, because the droplet size after filament breakup is calculated according to Eq. 9, this can lead to the situation that the daughter droplets after the filament breakup are actually larger than the parent droplet before the breakup event. An example is demonstrated in “Influence of shear rate \(\dot {\gamma } \)". The reason is probably that Eq. 9 was derived for a filament in a stretching flow (with nearly constant extensional rate), which means it is not valid for too small extensional rates

**D***, where the flow can be considered to be practically stagnant. This requires separate modeling of filament breakup under quiescent conditions, which we have not done in this work. This topic will be investigated in a subsequent paper.*

**: mm**## Numerical model

### Finite element formulation

*s*= log(

*β*) and

*v*= log(

*R*

_{0}). The reason is that

*s*and

*v*have the useful property that they are allowed to become negative, whereas

*β*and

*R*

_{0}could become negative due to numerical errors when simulated directly, which would lead to meaningless results. For example, Eq. 7 would take the square root of a negative number, which stops the numerical simulations. Eqs. 10 and 11 are replaced by:

*β*= exp(

*s*) and

*R*

_{0}= exp(

*v*). Before these can be implemented in a finite element framework, these equations are rewritten in a weak formulation, by multiplying the equations with test functions

*w*

_{1}and

*w*

_{2}and integrating over the whole domain Ω, to obtain:

*becomes:*

**b***is solved component-wise. In this work,*

**b***w*

_{1},

*w*

_{2}and the components of

*are chosen from the same function space. Flow fields are generated by solving the velocity*

**W***and the pressure*

**u***p*using the incompressible Stokes equations without body forces on different geometries. To elaborate, the flow field is determined from the continuity equation and momentum balance. Currently, the morphology is not coupled back to the velocity. The velocity field is calculated once, after which the morphology evolution is determined using this known velocity field. This back-coupling may be an interesting topic for future work.

### Numerical implementation

*t*is the time step. Putting the unknowns on the left hand side and the known quantities on the right-hand side results in:

*w*by

*w*+

*τ*

_{s}

*⋅∇*

**u***w*, where

*τ*

_{s}is the SUPG parameter. This parameter is given by:

*h*is a characteristic element size (Hughes et al. 1986) and

*U*is a characteristic velocity. There are several choices possible for

*U*. In this work,

*U*is calculated using the magnitude of the velocity

*in every integration point. We found this to be the most stable choice.*

**u***is solved first, followed by the problem of*

**b***s*(or

*β*) and finally the problem of

*v*(or

*R*

_{0}). Afterwards, during the next time step, the code loops back to

*(see Fig. 2).*

**b**The velocity * u* is discretized using second-order polynomial basis functions, while

*p*,

*s*,

*v*, and

*are discretized using first-order polynomial basis functions.*

**b**### Validation with simple shear flow

This section shows results for simple shear flow simulations with varying values of the smoothing parameter *τ* and the shear rate \(\dot {\gamma } \). We set the numerical smoothing parameters for filament breakup (*τ*_{b}), necking (*τ*_{n}) and coalescence (*τ*_{c}) equal, and define this value as *τ*. The main benefit of simple shear flow is that the shear rate is identical across the whole domain, which means the convection term in the morphology evolution equations drops out. This makes it possible to study the morphology evolution purely under the influence of deformation. Furthermore, the morphology can be simulated without using numerical smoothing, so results can be compared with the unsmoothed results by Peters et al. (2001).

#### Influence of numerical smoothing parameter *τ*

*t*= 10

^{− 4}s and no numerical smoothing is applied. The material properties are as given in Table 1. The material parameters are taken as those of a 10% PIB– 90% PDMS blend (same as Peters et al. (2001)). These values are used for all the simulation results in this work. First, filament stretching occurs, as can be seen from the gradual increase of the stretch ratio. Then suddenly filament breakup occurs, where the extremely extended filament breaks up into many smaller droplets. After some further breakup due to necking, a dynamic equilibrium between necking and coalescence is reached, which can be seen by the occasional upward spike indicating that the capillary number is momentarily larger than the critical capillary number. The sharp transitions of the stretch ratio are instantaneous (the up and down parts each span only one time step), as no numerical smoothing has yet been applied.

Simulation parameters

Quantity | Symbol | Value | Unit |
---|---|---|---|

Volume fraction | | 0.1 | – |

Droplet viscosity | | 86 | Pa ⋅ s |

Matrix viscosity | | 196 | Pa ⋅ s |

Interfacial tension | | 0.0023 | N/m |

Initial disturbance | | 4.66 ⋅ 10 | m |

Hamaker constant | | 10 | J |

*τ*= 0.1 s, the stretch ratio evolution has also been simulated (see Fig. 4). It is seen that the extreme jumps have indeed become smoother. The upward spikes in the dynamic equilibrium regime are no longer visible after the smoothing, as they only encompassed a relatively small part of one “period”. Note that the number of spikes in this final regime is not fixed (in the case without numerical smoothing), but dependent on the time step, because the time step determines how far the single necking step puts the capillary number Ca below the critical capillary number Ca

_{crit}. With a smaller time step, Ca decreases less below Ca

_{crit}after the instantaneous jump, so coalescence will make Ca reach Ca

_{crit}sooner, so upward spikes due to necking will occur more frequently in that case.

#### Influence of shear rate \(\dot {\gamma } \)

*R*

_{crit}, as given by Eq. 28, so

*R*

_{0}keeps increasing because

*R*

_{crit}keeps increasing due to orientation of the orientation vector

*with the flow field. The orientation vector is directly determined from the*

**m***tensor, which is not representative of the newly formed droplet after the breakup event.*

**c**To prevent * b* from growing indefinitely, the Giesekus relaxation term is added to Eq. 13. However, applying this relaxation of

*still does not eliminate the problem of the unexpected morphology evolution sequence, as the relaxation time*

**b***τ*

_{G}is usually chosen large compared to the timescale of the physical process. The issue seems to be that

*is not linked to*

**b***R*

_{crit}for low stretching rates. Equation 9 is not valid for too small values of

*:*

**D***, which occurs in simple shear flow when the droplet orients away from the direction of the background flow with the largest stretch (at 45*

**mm**^{∘}).

*and*

**b***R*

_{crit}affect only the part of filament stretching and filament breakup, it is decided to put an upper limit

*R*

_{crit,max}on

*R*

_{crit}, in such a way that the capillary number after breakup obeys Ca <

*κ*Ca

_{crit}, so that the next morphological state will always be necking (see Eq. 43).

*R*

_{crit,max}is given by:

*R*

_{crit}in Eq. 9 will not go to infinite in the instance that

**D***goes to zero.*

**: mm***β*rapidly alternates between the value for necking and coalescence. Furthermore, filament breakup is delayed, as the filament requires more deformation to become unstable. However, no filament stretching occurs at the shear rate of \(\dot {\gamma }= 1 \thinspace \mathrm {s}^{-1} \). This simulation immediately goes into the necking regime and continues until the dynamic equilibrium between necking and coalescence is reached. All in all, it is observed that as expected, the final droplet size decreases with increasing shear rate. We have validated our phenomenological model for simple shear flow and in the subsequent sections, we show results of our blend model in Poiseuille flow and an eccentric cylinder flow, both of which are relevant for practical applications.

## Results

### Poiseuille flow

In this section, we show results for Poiseuille flow, which essentially consists of many layers of simple shear flow at different shear rates. Poiseuille flow is a classical example of a pressure-driven flow, where a layered droplet structure arises near the walls, which is relevant for many industrial applications. The domain is a rectangle, with a mesh consisting of two elements in the (horizontal) *x*-direction and *N*_{y} elements in the (vertical) *y*-direction. The time step is Δ*t* = 10^{− 3} s and the smoothing parameter is *τ* = 10^{− 1} s. The top and bottom boundaries are no-slip boundaries. The left and right boundaries are coupled through a periodic boundary condition and a flow rate of *Q* = 10 m^{2}/s is imposed. The length in *y*-direction is *L*_{y} = 4 m and the length in *x*-direction is set equal to the width of two elements. The elements are squares, with biquadratic interpolation for velocity, bilinear interpolation for pressure and all the morphology variables. The initial droplet size is *R*_{0} = 9.5 ⋅ 10^{− 6} m and the initial stretch ratio is *β* = 1.

#### Comparison between standard and logarithmic versions of the blend model

As was discussed before, our model does not solve for the stretch ratio *β* and unstretched radius *R*_{0} directly, but their logarithmic counterparts *s* and *v*. This section demonstrates why the latter is the better choice.

*R*decreases below the critical filament radius

*R*

_{crit}, after which filament breakup occurs. When this occurs, the stretching filaments in the adjacent layer are not yet breaking up. During filament breakup, the blend model describes a nearly discontinuous jump in both

*β*and

*R*

_{0}. The numerical smoothing technique only smoothes discontinuities in the streamline direction, not perpendicular to it. This leads to the occurrence of the Gibbs phenomenon (see Fig. 9), because the continuous finite element basis functions cannot capture such a discontinuity. In the region of 0.5 <

*y*< 1 m, it can be seen that there is an almost discontinuous jump between a region where filament breakup has already occurred and a region where filaments are still stretching. Of particular interest is the downward peak of the red line. When the mesh is too coarse or the discontinuity is too large, this peak can reach a negative value. This is undesirable for two reasons.

First of all, a negative stretch ratio has no physical meaning and secondly, inserting a negative *β* into Eq. 7 leads to taking the square root of a negative number, which leads to a floating point exception error, making the numerical simulation stop. The logarithmic formulation with *s* and *v* has the benefit that *β* = exp(*s*) and *R*_{0} = exp(*v*) cannot become negative.

#### Mesh convergence

In this section, it is investigated how the solution at a very long time scale (2 ⋅ 10^{6} time steps, *t* = 2 ⋅ 10^{3} s) relates to the reference solution that is obtained by combining simple shear flow solutions at the same shear rate values as encountered in the Poiseuille flow problem. This comparison is useful, because the Poiseuille flow is affected by the oscillations of the Gibbs phenomenon, whereas the reference solution shows what the solution in every point should be, based on the local shear rate. The shear rates range from \(\dot {\gamma } = 10^{-6} \thinspace \mathrm {s}^{-1} \) to \(\dot {\gamma } = 3.75 \thinspace \mathrm {s}^{-1} \). Note that the minimum shear rate is not taken as \( \dot {\gamma } = 0 \), because * D* would then be a zero tensor and

*R*

_{crit}in Eq. 9 would go to infinity. Therefore, \(\dot {\gamma } = 10^{-6} \thinspace \mathrm {s}^{-1} \) has been taken as a value to investigate the morphology evolution at very low shear rates.

*N*

_{y}= 1000. As expected, the high shear rates near the walls have resulted in the smallest droplet sizes due to capillary breakup. Closer to the center, there is a region that remains nearly the initial droplet size. In this region, the capillary number Ca is too small to cause breakup, yet too large to allow for enough film drainage, so coalescence is unsuccessful here. Even closer to the center, coalescence is observed to be successful, as the droplets become slightly larger than the initial droplet size. Lastly, in the center itself, the shear rate is so low that not many collisions take place, so coalescence is again not (very) successful there.

*N*

_{y}= 50) shows erroneous behavior in the center of the domain (

*y*= 2). A lot of coalescence appears to be occurring while none would be expected. This phenomenon occurs up to a certain element size (around the element size at

*N*

_{y}= 200). Further mesh refinement at that point seems to give nearly linear convergence. Based on the linear interpolation used for the morphology variables, quadratic convergence would be expected, though this would only hold for smooth functions. The discontinuous solution is not smooth, for which only linear convergence can be achieved (Canuto et al. 1988). The solutions of the stretch ratio at a long time scale were also compared for

*N*

_{y}= 50 and

*N*

_{y}= 1000 (see Fig. 15). The convergence plot for the stretch ratio (see Fig. 16) has been generated by comparing the simple shear flow reference solution to the Poiseuille flow solution averaged over the final 1000 time steps. The averaging is done, because there is no true steady state solution, but a dynamic equilibrium between necking and coalescence. The convergence appears to be nearly linear throughout the whole range of

*N*

_{y}. To conclude this section on Poiseuille flow, we have motivated our description of the blend morphology with logarithmic quantities and we have shown that our phenomenological model can be used to predict the droplet morphology for a pressure-driven flow.

### Eccentric cylinder flow

#### Problem description and mesh convergence

*R*

_{outer}and the inner cylinder has radius

*R*

_{inner}(see Fig. 17).

*ϵ*. The first example shows the case where Ω = 1 s

^{− 1},

*R*

_{outer}= 1 m,

*R*

_{inner}= 0.3 m, and

*ϵ*= 0.3 m. The outer cylinder rotates clockwise. The effect of the element size has been investigated with the same simulation parameters as described in the previous section. Meshes are generated using Gmsh (Geuzaine and Remacle 2009). The starting point is a mesh with 1082 triangular elements (see Fig. 18). Quadratic triangular elements are used, where the velocity is interpolated quadratically and the pressure and morphology variables are interpolated linearly. Five meshes have been generated (see Table 2). The relative minimum element size \(\bar {h}_{\min } \) is calculated as the square root of the smallest element area divided by

*R*

_{outer}, where

*R*

_{outer}is used as the global length scale of the eccentric cylinder flow problem. The same approach is followed for calculating the relative maximum element size \(\bar {h}_{\max }\). For this convergence study, we focus on the morphology at

*t*= 80 s (the morphology no longer changes much over time) along the vertical line C1 between the top of the inner and outer cylinder (see Fig. 19 for the stretch ratio profile and Fig. 20 for the unstretched radius profile), as this line crosses both regions of interest of vortex flow and outer flow, and this line is relatively far away from the stagnation point which is not expected to yield useful information regarding mesh convergence.

Mesh statistics for convergence study

Mesh | nnodes | nelem | \(\bar {h}_{\min } \) | \(\bar {h}_{\max } \) |
---|---|---|---|---|

M0 | 2260 | 1082 | 2.16 ⋅ 10 | 9.47 ⋅ 10 |

M1 | 8848 | 4328 | 1.07 ⋅ 10 | 4.76 ⋅ 10 |

M2 | 35008 | 17312 | 5.36 ⋅ 10 | 2.38 ⋅ 10 |

M3 | 139264 | 69248 | 2.68 ⋅ 10 | 1.19 ⋅ 10 |

M4 | 555520 | 276992 | 1.34 ⋅ 10 | 5.95 ⋅ 10 |

It is observed that M0 and M1 yield morphology results that are very different from the most refined mesh M4. M4 shows significantly different behavior near the boundary of the inner cylinder, which suggests some boundary layer effect. The remaining part of the solution of M4 seems to be approximated quite well by M2 and M3. Since the computational time of M2 is a factor of 16 times faster than the finest mesh and the region of the boundary effect seems very narrow, M2 is considered good enough for further simulations. For other geometries (different eccentricities *ϵ*), meshes are generated with a relative minimum element size \(\bar {h}_{\min }\) of \(\mathcal {O}(10^{-3}) \).

To comment further on the boundary layer effect that is observed for M4, this raises an interesting point about how our blend model behaves when there are very small length scales, as are encountered in chaotic mixing flows. These length scales cannot be captured with a finite element mesh. As is shown in Figs. 19 and 20, M4 is observed to describe a thin boundary layer region that is smoothed by the coarser meshes. Although this example is not chaotic, we expect the numerical method to behave in a similar way for the small length scales in chaotic flow, meaning that small scale details are smoothed, but the numerical model will not fail. This would suggest that information is lost due to this smoothing. However, our macroscopic model does not contain information about the morphology at such small length scales to begin with, so the limitation is in the theoretical model itself and not in the numerical method. Basically, there is no point in simulating length scales smaller than the maximum droplet size, because smaller details are absorbed into the macroscopic description of the droplet populations. We do expect that, if the fine spatial layering would be captured, that breakup and coalescence would eliminate it. This is because two adjacent thin layers would experience approximately the same local shear rate and our model describes the final morphology according to the Grace curve, which breakup and coalescence would evolve towards. Droplet migration across streamlines has no effect in our model, because we assume all droplets to advect along the direction of the background flow field.

Other models by Muzzio et al. (1992) and Florek and Tucker (2005) are excellent for describing the stretching of the droplet morphology in globally chaotic flows. However, these models neglect interfacial tension and thereby omit breakup and coalescence events. The strength of our model lies in the ability to capture these topological changes.

#### Morphology evolution

^{− 1},

*R*

_{outer}= 1 m,

*R*

_{inner}= 0.3 m, and

*ϵ*= 0.3 m. In the outer regions, the flow rotates clockwise, while in the inner region above the inner cylinder there is a clockwise rotating vortex (see Fig. 21 for the streamline pattern and Fig. 22 for the shear rate pattern). The shear rate is observed to be largest below the inner cylinder, while being small above the inner cylinder and at the lower region near the outer cylinder.

*β*= 1 and unstretched radius

*R*

_{0}= 10

^{− 5}m has been simulated (see Figs. 23 and 24). The time step is Δ

*t*= 0.01 s, the smoothing parameter is

*τ*= 0.1 s, the Giesekus parameters are

*α*

_{G}= 0.01 and

*τ*

_{G}= 10

^{6}s. The simulation was run until time

*t*

_{end}= 60 s. It is seen that after 0.16 rotations, the stretch ratio first grows near the bottom of the inner cylinder (where the shear rate is largest) and is advected clockwise around the vortex above the inner cylinder. During the stretching process, it makes sense that the unstretched radius of the droplets does not change. After 0.56 and 0.72 rotations, the distinctive flow fields within and outside of the vortex can clearly be observed. Droplets in both regions stretch and rotate within their own regions, where the droplets in the outer region stretch faster because of passing the region of large shear rates below the inner cylinder. Some of the droplets can already be observed to have broken up. There seems to be an outward moving breakup front. Eventually, after 1.43 rotations, the droplets in the inner vortex have also broken up. Afterwards, after around three rotations, the final morphology is reached.

#### Effect of *ϵ*

*ϵ*= 0.2 m,

*ϵ*= 0.3 m, and

*ϵ*= 0.5 m. The other parameters are Ω = 1 s

^{− 1},

*R*

_{outer}= 1 m, and

*R*

_{inner}= 0.3 m. The initial values are

*β*= 1 and

*R*

_{0}= 10

^{− 5}m. The mean droplet size and its standard deviation along curve C1 were plotted over time (see Fig. 25).

It is seen that the geometry with the inner cylinder closest to the outer cylinder produces the finest morphology, with the highest amount of uniformity and in the shortest amount of time. It makes sense that the finest morphology is obtained, because the narrow region between the two cylinders results in larger shear rates than in the other two flow problems. The high amount of uniformity is due to the large area of the vortex above the inner cylinder, which easily distributes droplets over a large portion of the domain. The short process time is also related to the large shear rates, which leads to droplets stretching faster and breaking up faster.

#### Effect of Ω

^{− 1}, Ω = 1 s

^{− 1}and Ω = 2 s

^{− 1}. The other parameters are

*ϵ*= 0.3 m,

*R*

_{outer}= 1 m, and

*R*

_{inner}= 0.3 m. The initial values are

*β*= 1 and

*R*

_{0}= 10

^{− 5}m. The time evolution of the mean droplet size and its standard deviation along curve C1 is investigated (see Fig. 26).

Increasing Ω appears to have a similar effect to increasing *ϵ*. The reason is the same as in the case of varying *ϵ*. For higher Ω, larger shear rates are generated in the narrow region between the two cylinders. The higher Ω also improves the uniformity of the morphology, as it makes the flow faster and therefore, the efficiency of mixing is improved. We have hereby shown our model to be useful for predicting the spatial and temporal development of a disperse blend morphology in a complex flow geometry.

## Conclusions

We developed a numerical model to describe the evolution of the morphology of disperse blends in complex flows, using a Stokes flow and the model by Peters et al. (2001) as a starting point. Our phenomenological model was implemented in an inhouse FEM code. For validation, our model was first compared with the Peters model for simple shear flow, with good agreement. Filament breakup under nearly quiescent conditions was found to be an important morphology state, but has not yet been taken into account in our model, which is a topic for future work.

The next step was to simulate the morphology development along the cross-section of a Poiseuille flow problem. In the Poiseuille flow example, the occurrence of the Gibbs phenomenon was observed. These Gibbs oscillations were found to possibly result in negative stretch ratios when *β* was simulated directly. This justifies the choice of calculating the stretch ratio with the variable *s* = log(*β*).

After simulating Poiseuille flow, the model was used to study the morphology development in the eccentric cylinder flow problem, where the outer cylinder rotates with angular velocity Ω. The effect of the position of the inner cylinder and Ω were investigated. Putting the two cylinders closer to each other and increasing Ω were the best choices for obtaining the finest morphology, with the highest amount of uniformity in the shortest amount of processing time. In both cases, the cause was the increased shear rate in the narrow region between the inner and outer cylinder.

While the original model by (Peters et al. 2001) has already been validated for simple shear flow with experiments done by Vinckier et al. (1997), for future work it would be interesting to experimentally validate the blend model for Poiseuille flow and eccentric cylinder flow.

We have now obtained a predictive tool for estimating how to design the complex geometry of a mixing device in order to obtain a desired disperse blend morphology, for different process conditions and material properties.

## Notes

### Acknowledgments

The authors would like to thank SABIC for financial support of this work.

## References

- Almusallam A, Larson R, Solomon M (2004) Comprehensive constitutive model for immiscible blends of newtonian polymers. J Rheumatol 48(2):319–348. https://doi.org/10.1122/1.1648644 Google Scholar
- Batchelor GK (1970) The stress system in a suspension of force-free particles. J Fluid Mech 41(3):545–570. https://doi.org/10.1017/S0022112070000745 CrossRefGoogle Scholar
- Bazhlekov IB, Anderson PD, Meijer HEH (2006) Numerical investigation of the effect of insoluble surfactants on drop deformation and breakup in simple shear flow. J Colloid Interface Sci 298(1):369–394. https://doi.org/10.1016/j.jcis.2005.12.017 CrossRefGoogle Scholar
- Bentley BJ, Leal LG (1986a) A computer-controlled four-roll mill for investigations of particle and drop dynamics in two-dimensional linear shear flows. J Fluid Mech 167:219–240. https://doi.org/10.1017/S002211208600280X CrossRefGoogle Scholar
- Bentley BJ, Leal LG (1986b) An experimental investigation of drop deformation and breakup in steady, two-dimensional linear flows. J Fluid Mech 167:241–283. https://doi.org/10.1017/S0022112086002811 CrossRefGoogle Scholar
- Canuto C, Hussaini M, Quarteroni A, Zang T (1988) Spectral methods in fluid dynamics. Springer, Berlin. https://doi.org/10.1007/978-3-642-84108-8 CrossRefGoogle Scholar
- Chesters AK (1991) The modelling of coalescence processes in fluid-liquid dispersions : a review of current understanding. Chem Eng Res Des 69(A4):259–270Google Scholar
- Choi SJ, Schowalter WR (1975) Rheological properties of nondilute suspensions of deformable particles. Phys Fluids 18:420–427. https://doi.org/10.1063/1.861167 CrossRefGoogle Scholar
- Cox RG (1969) The deformation of a drop in a general time-dependent fluid flow. J Fluid Mech 37(3):601–623. https://doi.org/10.1017/S0022112069000759 CrossRefGoogle Scholar
- De Bruijn RA (1989) Deformation and breakup of drops in simple shear flows. PhD thesis, Department of Applied Physics, https://doi.org/10.6100/IR318702
- Doi M, Ohta T (1991) Dynamics and rheology of complex interfaces. i. J Chem Phys 95(2):1242–1248. https://doi.org/10.1063/1.461156 CrossRefGoogle Scholar
- Edwards BJ, Dressler M, Grmela M, Ait-Kadi A (2003) Rheological models with microstructural constraints. Rheol Acta 42(1):64–72. https://doi.org/10.1007/s00397-002-0256-9 CrossRefGoogle Scholar
- Florek CA, Tucker CL (2005) Stretching distributions in chaotic mixing of droplet dispersions with unequal viscosities. Phys Fluids 17(5):053101. https://doi.org/10.1063/1.1895798 CrossRefGoogle Scholar
- Geuzaine C, Remacle JF (2009) Gmsh: a three-dimensional finite element mesh generator with built-in pre- and post-processing facilities. Int J Numer Methods Eng 79(11):1309–1331. https://doi.org/10.1002/nme.2579 CrossRefGoogle Scholar
- Grace HP (1982) Dispersion phenomena in high viscosity immiscible fluid systems and application of static mixers as dispersion devices in such systems. Chem Eng Commun 14(3–6):225–277. https://doi.org/10.1080/00986448208911047 CrossRefGoogle Scholar
- Grizzuti N, Bifulco O (1997) Effects of coalescence and breakup on the steady-state morphology of an immiscible polymer blend in shear flow. Rheol Acta 36(4):406–415. https://doi.org/10.1007/BF00396327 CrossRefGoogle Scholar
- Grmela M, Öttinger HC (1997) Dynamics and thermodynamics of complex fluids. i. development of a general formalism. Phys Rev E 56:6620–6632. https://doi.org/10.1103/PhysRevE.56.6620 CrossRefGoogle Scholar
- Grmela M, Bousmina M, Palierne JF (2001) On the rheology of immiscible blends. Rheol Acta 40(6):560–569. https://doi.org/10.1007/s003970100188 CrossRefGoogle Scholar
- Guido S, Greco F (2001) Drop shape under slow steady shear flow and during relaxation. experimental results and comparison with theory. Rheol Acta 40(2):176–184. https://doi.org/10.1007/s003970000144 CrossRefGoogle Scholar
- Hughes TJR, Mallet M, Mizukami A (1986) A new finite element formulation for computational fluid dynamics: Ii. beyond supg. Comput Methods Appl Mech Eng 54(3):341–355. https://doi.org/10.1016/0045-7825(86)90110-6 CrossRefGoogle Scholar
- Hütter M, Hulsen MA, Anderson PD (2018) Fluctuating viscoelasticity. J Non-Newtonian Fluid Mech. https://doi.org/10.1016/j.jnnfm.2018.02.012
- Jansen KMB, Agterof WGM, Mellema J (2001) Droplet breakup in concentrated emulsions. J Rheol 45(1):227–236. https://doi.org/10.1122/1.1333001 CrossRefGoogle Scholar
- Janssen JMH (1993) Dynamics of liquid-liquid mixing. PhD thesis, Eindhoven University of Technology, https://doi.org/10.6100/IR404184
- Janssen PJA, Anderson PD (2008) Surfactant-covered drops between parallel plates. Chem Eng Res Des 86(12):1388–1396. https://doi.org/10.1016/j.cherd.2008.08.014 CrossRefGoogle Scholar
- Khakhar DV, Ottino JM (1987) Breakup of liquid threads in linear flows. Int J Multiphase Flow 13(1):71–86. https://doi.org/10.1016/0301-9322(87)90008-5 CrossRefGoogle Scholar
- Maffettone PL, Minale M (1998) Equation of change for ellipsoidal drops in viscous flow. J Non-Newtonian Fluid Mech 78(2):227–241. https://doi.org/10.1016/S0377-0257(98)00065-2 CrossRefGoogle Scholar
- Mikami T, Cox RG, Mason SG (1975) Breakup of extending liquid threads. Int J Multiphase Flow 2(2):113–138. https://doi.org/10.1016/0301-9322(75)90003-8 CrossRefGoogle Scholar
- Minale M (2010) Models for the deformation of a single ellipsoidal drop: a review. Rheol Acta 49(8):789–806. https://doi.org/10.1007/s00397-010-0442-0 CrossRefGoogle Scholar
- Muzzio FJ, Meneveau C, Swanson PD, Ottino JM (1992) Scaling and multifractal properties of mixing in chaotic flows. Phys Fluids A 4(7):1439–1456. https://doi.org/10.1063/1.858419 CrossRefGoogle Scholar
- Peters GWM, Hansen S, Meijer HEH (2001) Constitutive modeling of dispersive mixtures. J Rheol 45(3):659–689. https://doi.org/10.1122/1.1366714 CrossRefGoogle Scholar
- Stegeman YW, Chesters AK, Vosse, van de FN, Meijer HEH (1999) Breakup of (non-) newtonian droplets in a time-dependent elongational flow. In: Anderson PD, Kruijt PGM (eds) Polymer processing society : annual meeting, 15th, ’s-Hertogenbosch, The Netherlands, May 31 - June 4, 1999 : proceedings, Polymer processing SocietyGoogle Scholar
- Stone HA (1994) Dynamics of drop deformation and breakup in viscous fluids. Annu Rev Fluid Mech 26(1):65–102. https://doi.org/10.1146/annurev.fl.26.010194.000433 CrossRefGoogle Scholar
- Stone HA, Bentley BJ, Leal LG (1986) An experimental study of transient effects in the breakup of viscous drops. J Fluid Mech 173:131–158. https://doi.org/10.1017/S0022112086001118 CrossRefGoogle Scholar
- Taylor GI (1932) The viscosity of a fluid containing small drops of another fluid. Proceedings of the Royal Society of London A: Mathematical, Physical and Engineering Sciences 138(834):41–48. https://doi.org/10.1098/rspa.1932.0169 CrossRefGoogle Scholar
- Taylor GI (1934) The formation of emulsions in definable fields of flow. Proceedings of the Royal Society of London A: Mathematical, Physical and Engineering Sciences 146(858):501–523. https://doi.org/10.1098/rspa.1934.0169 CrossRefGoogle Scholar
- Tjahjadi M, Ottino JM (1991) Stretching and breakup of droplets in chaotic flows. J Fluid Mech 232:191–219. https://doi.org/10.1017/S0022112091003671 CrossRefGoogle Scholar
- Tomotika S (1935) On the instability of a cylindrical thread of a viscous liquid surrounded by another viscous fluid. Proceedings of the Royal Society of London A: Mathematical, Physical and Engineering Sciences 150(870):322–337. https://doi.org/10.1098/rspa.1935.0104 CrossRefGoogle Scholar
- Tucker CL, Moldenaers P (2002) Microstructural evolution in polymer blends. Annu Rev Fluid Mech 34 (1):177–210. https://doi.org/10.1146/annurev.fluid.34.082301.144051 CrossRefGoogle Scholar
- Van Puyvelde P, Moldenaers P (2005) Rheology and morphology development in immiscible polymer blends. Rheol Rev: 101–145. https://doi.org/10.1.1.361.7276Google Scholar
- Vinckier I, Mewis J, Moldenaers P (1997) Stress relaxation as a microstructural probe for immiscible polymer blends. Rheol Acta 36(5):513–523. https://doi.org/10.1007/BF00368129 CrossRefGoogle Scholar

## Copyright information

**Open Access**This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.