Advertisement

Experiments in Fluids

, 60:7 | Cite as

Control of salient flow features in the wake of a \(25^{\circ }\) Ahmed model using microjets

  • Jonathan McNallyEmail author
  • Nicolas Mazellier
  • Farrukh Alvi
  • Azeddine Kourta
Research Article
  • 165 Downloads

Abstract

Flow control, employing linear arrays of discrete microjets, is applied to the rear of a \(25^{\circ }\) Ahmed model. The locations of the arrays are selected to test the effectiveness of microjet control at directly manipulating the various features found in typical flow fields generated by ground vehicles. Parametric sweeps are conducted to investigate the flow response as a function of the jet velocity and momentum. The effect and efficiency of the control are quantified through aerodynamic force measurements, while local modifications are investigated via pressure measurements on the rear surfaces of the model. The change in the pressure distribution reveals each control’s effects on a targeted flow structure and highlights the complex interaction between the salient flow features found in the wake of the Ahmed model. The strategies tested reveal a balance between the closed separation and longitudinal vortices which form above the rear slant surface, with beneficial modifications to one structure (in terms of drag reduction) often complimented by a detrimental contribution by the other. Areas of pressure recovery on the surface of the model are observed for each control technique and the changes to the aerodynamic forces are quantified. Microjets proved most effective when utilized for separation control producing a maximum change to the coefficients of drag and lift of \(-\,10.6\%\) and \(-\,18\%\) of the baseline values, respectively. Control techniques targeting other flow structures such as the C-pillar vortices and trailing wake proved less effective, producing a maximum reduction in drag and lift of \(-\,0.9\%\) and \(-\,6\%\).

Graphical abstract

Notes

References

  1. Ahmed S (1983) Influence of base slant on the wake structure and drag of road vehicles. J Fluids Eng 105(4):429–434CrossRefGoogle Scholar
  2. Ahmed S, Ramm G, Faltin G (1984) Some salient features of the time-averaged ground vehicle wake. SAE Changes 2012:12–11Google Scholar
  3. Aubrun S, McNally J, Alvi F, Kourta A (2011) Separation flow control on a generic ground vehicle using steady microjet arrays. Exp Fluids 51(5):1177–1187CrossRefGoogle Scholar
  4. Barros D, Borée J, Noack BR, Spohn A (2016) Resonances in the forced turbulent wake past a 3D blunt body. Phys Fluids 28(6):065104 (1994-present)CrossRefGoogle Scholar
  5. Beaudoin JF, Aider JL (2008) Drag and lift reduction of a 3D bluff body using flaps. Exp Fluids 44(4):491–501CrossRefGoogle Scholar
  6. Bruneau CH, Creusé E, Depeyras D, Gillieron P, Mortazavi I (2012) Active and passive flow control around simplified ground vehicles. J Appl Fluid Mech 5(1):89–93Google Scholar
  7. Brunn A, Wassen E, Sperber D, Nitsche W, Thiele F (2007) Active drag control for a generic car model. In: Active flow control. Springer, pp 247–259Google Scholar
  8. Choi H, Jeon WP, Kim J (2008) Control of flow over a bluff body. Ann Rev Fluid Mech 40:113–139MathSciNetzbMATHCrossRefGoogle Scholar
  9. Choi H, Lee J, Park H (2014) Aerodynamics of heavy vehicles. Ann Rev Fluid Mech 46:441–468MathSciNetzbMATHCrossRefGoogle Scholar
  10. Grandemange M, Mary A, Gohlke M, Cadot O (2013) Effect on drag of the flow orientation at the base separation of a simplified blunt road vehicle. Exp Fluids 54(5):1529CrossRefGoogle Scholar
  11. Hucho WH (2013) Aerodynamics of road vehicles: from fluid mechanics to vehicle engineering. Elsevier, AmsterdamGoogle Scholar
  12. Joseph P, Amandolèse X, Aider JL (2012) Drag reduction on the 25 slant angle Ahmed reference body using pulsed jets. Exp Fluids 52(5):1169–1185CrossRefGoogle Scholar
  13. Joseph P, Amandolese X, Edouard C, Aider JL (2013) Flow control using mems pulsed micro-jets on the Ahmed body. Exp Fluids 54(1):1–12CrossRefGoogle Scholar
  14. Keogh J, Barber T, Diasinos S, Doig G (2016) The aerodynamic effects on a cornering Ahmed body. J Wind Eng Ind Aerodyn 154:34–46CrossRefGoogle Scholar
  15. Kourta A, Gillieron P (2009) Impact of the automotive aerodynamic control on the economic issues. J Appl Fluid Mech 2(2):69–75Google Scholar
  16. Kourta A, Thacker A, Joussot R (2015) Analysis and characterization of ramp flow separation. Exp Fluids 56(5):104CrossRefGoogle Scholar
  17. Krajnović S, Davidson L (2005) Flow around a simplified car, part 1: large eddy simulation. J Fluids Eng 127(5):907–918CrossRefGoogle Scholar
  18. Krajnović S, Davidson L (2005) Flow around a simplified car, part 2: understanding the flow. J Fluids Eng 127(5):919–928CrossRefGoogle Scholar
  19. Krajnović S, Östh J, Basara B (2009) LES of active flow control around an Ahmed body with active flow control. In: Conference on modelling fluid flow (CMFF09), BudapestGoogle Scholar
  20. Lienhart H, Stoots C, Becker S (2002) Flow and turbulence structures in the wake of a simplified car model (Ahmed model). In: New results in numerical and experimental fluid mechanics III. Springer, pp 323–330Google Scholar
  21. Littlewood R, Passmore MA (2012) Aerodynamic drag reduction of a simplified squareback vehicle using steady blowing. Exp Fluids 53(2):519–529CrossRefGoogle Scholar
  22. Machida K, Kaneko M, Kotada T, Murakawa A, Ogawa A (2014) Aerodynamic development of the 2014 model year fit. Honda R&D Tech Rev Tech Rev 26(1):78–85Google Scholar
  23. McNally J, Fernandez E, Kumar R, Alvi F (2012) Near wake dynamics for an Ahmed body with active flow control. In: 6th AIAA flow control conferenceGoogle Scholar
  24. McNally J, Fernandez E, Robertson G, Kumar R, Taira K, Alvi F, Yamaguchi Y, Murayama K (2015) Drag reduction on a flat-back ground vehicle with active flow control. J Wind Eng Ind Aerodyn 145:292–303CrossRefGoogle Scholar
  25. Metka M, Gregory JW (2015) Drag reduction on the 25-deg Ahmed model using fluidic oscillators. J Fluids Eng 137(5):051,108CrossRefGoogle Scholar
  26. Nakamura D, Onishi Y, Takehara Y (2014) Aerodynamic development of 2013 model year Accord and Accord Hybrid. Honda R&D Tech Rev Tech Rev 26(1):86–93Google Scholar
  27. Park H, Lee D, Jeon WP, Hahn S, Kim J, Kim J, Choi J, Choi H (2006) Drag reduction in flow over a two-dimensional bluff body with a blunt trailing edge using a new passive device. J Fluid Mech 563:389–414zbMATHCrossRefGoogle Scholar
  28. Park H, Cho JH, Lee J, Lee DH, Kim KH (2013) Experimental study on synthetic jet array for aerodynamic drag reduction of a simplified car. J Mech Sci Technol 27(12):3721–3731CrossRefGoogle Scholar
  29. Pujals G, Depardon S, Cossu C (2010) Drag reduction of a 3d bluff body using coherent streamwise streaks. Exp Fluids 49(5):1085–1094CrossRefGoogle Scholar
  30. Rodriguez R, Murzyn F, Mehel A, Larrarte F (2017) Experimental study of the wake flow behind three road vehicle models. In: 23ème Congrès Français de Mécanique, p 13Google Scholar
  31. Rossitto G, Sicot C, Ferrand V, Borée J, Harambat F (2016) Influence of afterbody rounding on the pressure distribution over a fastback vehicle. Exp Fluids 57(3):1–12CrossRefGoogle Scholar
  32. Rouméas M, Gilliéron P, Kourta A (2009) Drag reduction by flow separation control on a car after body. Int J Numer Methods Fluids 60(11):1222–1240zbMATHCrossRefGoogle Scholar
  33. Sims-Williams DB, Duncan BD (2003) The Ahmed model unsteady wake: experimental and computational analyses. SAE Trans 112(6):1385–1396Google Scholar
  34. Thacker A, Aubrun S, Leroy A, Devinant P (2012) Effects of suppressing the 3D separation on the rear slant on the flow structures around an Ahmed body. J Wind Eng Ind Aerodyn 107:237–243CrossRefGoogle Scholar
  35. Thacker A, Aubrun S, Leroy A, Devinant P (2013) Experimental characterization of flow unsteadiness in the centerline plane of an Ahmed body rear slant. Exp Fluids 54(3):1–16CrossRefGoogle Scholar
  36. Tunay T, Sahin B, Ozbolat V (2014) Effects of rear slant angles on the flow characteristics of Ahmed body. Exp Thermal Fluid Sci 57:165–176CrossRefGoogle Scholar
  37. Vino G, Watkins S, Mousley P, Watmuff J, Prasad S (2005) Flow structures in the near-wake of the Ahmed model. J Fluids Struct 20(5):673–695CrossRefGoogle Scholar
  38. Volpe R, Devinant P, Kourta A (2015) Experimental characterization of the unsteady natural wake of the full-scale square back Ahmed body: flow bi-stability and spectral analysis. Exp Fluids 56(5):99CrossRefGoogle Scholar
  39. Wang X, Zhou Y, Pin Y, Chan T (2013) Turbulent near wake of an Ahmed vehicle model. Exp Fluids 54(4):1–19CrossRefGoogle Scholar
  40. Westerweel J, Scarano F (2005) Universal outlier detection for PIV data. Exp Fluids 39(6):1096–1100CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  • Jonathan McNally
    • 1
    Email author
  • Nicolas Mazellier
    • 2
  • Farrukh Alvi
    • 1
  • Azeddine Kourta
    • 2
  1. 1.Florida Center of Advanced AeropropulsionFlorida State UniversityTallahasseeUSA
  2. 2.Univ. Orléans, INSA-CVL, PRISME, EA4229Orléans cedexFrance

Personalised recommendations