Advertisement

A high-strength electrospun PPESK fibrous membrane for lithium-ion battery separator

  • Wenzheng Gong
  • Junfeng Gu
  • Shilun Ruan
  • Changyu Shen
Original Paper
  • 17 Downloads

Abstract

The electrospun fibrous membranes used as lithium-ion battery separators have been widely studied due to the advantages of high porosity, large specific surface area and adjustable structural characteristics. In order to obtain thermal stable and high-strength electrospun fibrous membranes for lithium-ion battery separators, the oriented poly(phthalazinone ether sulfone ketone) (PPESK) fibrous membranes were fabricated and then hot pressed with two pieces of membranes overlaid perpendicularly. The prepared hot-pressed composite oriented PPESK membranes show high tensile strength of 22.8 MPa at both horizontal and vertical directions. The hot-pressed oriented PPESK membranes are thermally dimensional stable even at the high temperature of 200 °C. In addition, the novel PPESK fibrous membranes exhibit high porosity (70%), superior electrolyte uptake (525%), low interfacial resistance (268 Ω) with electrodes and excellent ionic conductivity (1.39 mS cm−1). The simulated cells using the new separators show high discharge capacity and excellent rate capability, which demonstrates the novel membranes have potential to be used as separators for power lithium-ion batteries.

Keywords

Lithium-ion battery Separator Electrospinning PPESK Mechanical strength 

Notes

Acknowledgements

The authors would like to acknowledge financial support from National Natural Science Foundations of China (11432003), Innovation and Talent Recruitment Base on Numerical Simulation and Optimization of Rubber and Plastic Products Forming (B14013).

References

  1. 1.
    Goodenough JB, Kim Y (2010) Challenges for rechargeable Li batteries. Chem Mater 22:587–603CrossRefGoogle Scholar
  2. 2.
    Huang X (2011) Separator technologies for lithium-ion batteries. J Solid State Electrochem 15:649–662CrossRefGoogle Scholar
  3. 3.
    Valizadeh A, Farkhani SM (2014) Electrospinning and electrospun nanofibres. IET Nanobiotechnol 8:83–92CrossRefGoogle Scholar
  4. 4.
    Hwang K, Kwon B, Byun H (2011) Preparation of PVdF nanofiber membranes by electrospinning and their use as secondary battery separators. J Membr Sci 378:111–116CrossRefGoogle Scholar
  5. 5.
    Miao Y-E, Zhu G-N, Hou H, Xia Y-Y, Liu T (2013) Electrospun polyimide nanofiber-based nonwoven separators for lithium-ion batteries. J Power Sources 226:82–86CrossRefGoogle Scholar
  6. 6.
    Silberstein MN, Pai C-L, Rutledge GC, Boyce MC (2012) Elastic–plastic behavior of non-woven fibrous mats. J Mech Phys Solids 60:295–318CrossRefGoogle Scholar
  7. 7.
    Yanilmaz M, Chen C, Zhang X (2013) Fabrication and characterization of SiO2/PVDF composite nanofiber-coated PP nonwoven separators for lithium-ion batteries. J Polym Sci B Polym Phys 51:1719–1726CrossRefGoogle Scholar
  8. 8.
    Carol P, Ramakrishnan P, John B, Cheruvally G (2011) Preparation and characterization of electrospun poly(acrylonitrile) fibrous membrane based gel polymer electrolytes for lithium-ion batteries. J Power Sources 196:10156–10162CrossRefGoogle Scholar
  9. 9.
    Ding Y, Di W, Jiang Y, Xu F, Long Z, Ren F, Zhang P (2009) The morphological evolution, mechanical properties and ionic conductivities of electrospinning P(VDF-HFP) membranes at various temperatures. Ionics 15:731–734CrossRefGoogle Scholar
  10. 10.
    Liu J, Chang M-J, Du H-L (2016) Facile preparation of cross-linked porous poly(vinyl alcohol) nanofibers by electrospinning. Mater Lett 183:318–321CrossRefGoogle Scholar
  11. 11.
    Xinsheng Z, Qiang G, Xiaoli S, Qianqian P, Xiaoshan J, Ran T (2011) Reinforcement of electrospun nonwovens. Adv Mater Res 175–176:121–126Google Scholar
  12. 12.
    Yanilmaz M, Zhu J, Lu Y, Ge Y, Zhang X (2017) High-strength, thermally stable nylon 6,6 composite nanofiber separators for lithium-ion batteries. J Mater Sci 52:5232–5241CrossRefGoogle Scholar
  13. 13.
    Zaccaria M, Gualandi C, Fabiani D, Focarete ML, Croce F (2012) Effect of oxide nanoparticles on thermal and mechanical properties of electrospun separators for lithium-ion batteries. J Nanomater 2012:1–8CrossRefGoogle Scholar
  14. 14.
    Yunyun Z, Na W, Xue M, Yang S, Jianyong Y, Al-Deyab SS, El-Newehy M, Bin D (2014) Sandwich-structured PVdF/PMIA/PVdF nanofibrous separators with robust mechanical strength and thermal stability for lithium ion batteries. J Mater Chem A 2:14511–14518CrossRefGoogle Scholar
  15. 15.
    Park S-R, Jung Y-C, Shin W-K, Ahn KH, Lee CH, Kim D-W (2017) Cross-linked fibrous composite separator for high performance lithium-ion batteries with enhanced safety. J Membr Sci 527:129–136CrossRefGoogle Scholar
  16. 16.
    Hao J, Lei G, Li Z, Wu L, Xiao Q, Wang L (2013) A novel polyethylene terephthalate nonwoven separator based on electrospinning technique for lithium ion battery. J Membr Sci 428:11–16CrossRefGoogle Scholar
  17. 17.
    Qi W, Lu C, Chen P, Cui T (2010) Influence of collecting velocity on fiber orientation, morphology and tensile properties of electrospun PPESK fabrics. J Appl Polym Sci 118:2236–2243Google Scholar
  18. 18.
    Min Y, Junbo H (2012) Membranes in lithium ion batteries. Membranes 2:367–383CrossRefGoogle Scholar
  19. 19.
    Manzetti S, Mariasiu F (2015) Electric vehicle battery technologies: From present state to future systems. Renew Sustain Energy Rev 51:1004–1012CrossRefGoogle Scholar
  20. 20.
    Deimede V, Elmasides C (2015) Separators for lithium-ion batteries: a review on the production processes and recent developments. Energy Technol 3:453–468CrossRefGoogle Scholar
  21. 21.
    Yanilmaz M, Dirican M, Zhang X (2014) Evaluation of electrospun SiO2/nylon 6,6 nanofiber membranes as a thermally-stable separator for lithium-ion batteries. Electrochim Acta 133:501–508CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  1. 1.School of Materials Science and EngineeringDalian University of TechnologyDalianPeople’s Republic of China
  2. 2.Department of Engineering Mechanics, Key Laboratory of Industrial Equipment Structural AnalysisDalian University of TechnologyDalianPeople’s Republic of China

Personalised recommendations