Perforated fins effect on the heat transfer rate from a circular tube by using wind tunnel: An experimental view

  • Afshin Ahmadi Nadooshan
  • Rasool Kalbasi
  • Masoud Afrand
Original
  • 12 Downloads

Abstract

Perforated fins effects on the heat transfer rate of a circular tube are examined experimentally. An experimental system is set up through the wind tunnel and equipped with necessary measurement tools. Hot water passes through the finned tube and heat transfers to the fin-side air created using the wind tunnel with different velocities. Two fin sets of identical weight are installed on a circular tube with different outer diameters of 22 and 26 mm. The experiments are conducted at two different mass flow rates of the hot water and six Reynolds number of external air flow. Considering the four finned tubes and one no finned tube, a total of 60 tests are conducted. Results showed that with increasing the internal or external flow rates, the effect of larger cross-sectional area is greater. By opening holes on the fins, in addition to weight loss, the maximum heat transfer rate for perforated fins increases by 8.78% and 9.23% respectively for mass flow rates of 0.05 and 0.1 kg/s at low external Reynolds number. While, at high external Reynolds number, the holes reduces heat transfer by 8.4% and 10.6% for mass flow rates of 0.05 and 0.1 kg/s, respectively.

Notes

References

  1. 1.
    Zadhoush M, Nadooshan AA, Afrand M (2017) Constructal optimization of longitudinal and latitudinal rectangular fins used for cooling a plate under free convection by the intersection of asymptotes method. Int J Heat Mass Transf 112:441–453CrossRefGoogle Scholar
  2. 2.
    Bayareh M, Pordanjani AH, Nadooshan AA, Dehkordi KS (2017) Numerical study of the effects of stator boundary conditions and blade geometry on the efficiency of a scraped surface heat exchanger. Appl Therm Eng 113:1426–1436CrossRefGoogle Scholar
  3. 3.
    Salimpour MR, Kalbasi R, Lorenzini G (2017) Constructal multi-scale structure of PCM-based heat sinks. Contin Mech Thermodyn 29(2):477–491CrossRefGoogle Scholar
  4. 4.
    Kalbasi R, Salimpour MR (2015) Constructal design of phase change material enclosures used for cooling electronic devices. Appl Therm Eng 84:339–349CrossRefGoogle Scholar
  5. 5.
    Kalbasi R, Salimpour MR (2015) Constructal design of horizontal fins to improve the performance of phase change material rectangular enclosures. Appl Therm Eng 91:234–244CrossRefGoogle Scholar
  6. 6.
    Bhuiyan AA, Islam AKMS (2016) Thermal and hydraulic performance of finned-tube heat exchangers under different flow ranges: A review on modeling and experiment. Int J Heat Mass Transf 101:38–59CrossRefGoogle Scholar
  7. 7.
    Sinha A, Chattopadhyay H, Iyengar AK, Biswas G (2016) Enhancement of heat transfer in a fin-tube heat exchanger using rectangular winglet type vortex generators. Int J Heat Mass Transf 101:667–681CrossRefGoogle Scholar
  8. 8.
    Gholami MA, Wahid HAM (2017) Thermal–hydraulic performance of fin-and-oval tube compact heat exchangers with innovative design of corrugated fin patterns. Int J Heat Mass Transf 106:573–592CrossRefGoogle Scholar
  9. 9.
    Gu L, Min J, Wu X, Yang L (2017) Airside heat transfer and pressure loss characteristics of bare and finned tube heat exchangers used for aero engine cooling considering variable air properties. Int J Heat Mass Transf 108(Part B):1839–1849CrossRefGoogle Scholar
  10. 10.
    Chen H-T, Chiu Y-J, Tseng H-C, Chang J-R (2017) Effect of domain boundary set on natural convection heat transfer characteristics for vertical annular finned tube heat exchanger. Int J Heat Mass Transf 109:668–682CrossRefGoogle Scholar
  11. 11.
    Park J-S, Kim J, Lee K-S (2017) Thermal and drainage performance of a louvered fin heat exchanger according to heat exchanger inclination angle under frosting and defrosting conditions. Int J Heat Mass Transf 108(Part B):1335–1339CrossRefGoogle Scholar
  12. 12.
    Khatua AK, Kumar P, Singh HN, Kumar R (2016) Measurement of enhanced heat transfer coefficient with perforated twisted tape inserts during condensation of R-245fa. Heat Mass Transf 52(4):683–691CrossRefGoogle Scholar
  13. 13.
    Kumar R, Kumar A, Sharma A, Chauhan R, Sethi M (2017) Experimental study of heat transfer enhancement in a rectangular duct distributed by multi V-perforated baffle of different relative baffle width. Heat Mass Transf 53(4):1289–1304CrossRefGoogle Scholar
  14. 14.
    Elsayed ML, Mesalhy O (2015) Studying the performance of solid/perforated pin-fin heat sinks using entropy generation minimization. Heat Mass Transf 51(5):691–702CrossRefGoogle Scholar
  15. 15.
    Chin S-B, Foo J-J, Lai Y-L, Yong TK-K (2013) Forced convective heat transfer enhancement with perforated pin fins. Heat Mass Transf 49(10):1447–1458CrossRefGoogle Scholar
  16. 16.
    Gautam A, Pandey L, Singh S (2018) Influence of perforated triple wing vortex generator on a turbulent flow through a circular tube. Heat Mass Transf:1–13.  https://doi.org/10.1007/s00231-018-2296-4
  17. 17.
    Suri ARS, Kumar A, Maithani R (2018) Experimental investigation of heat transfer and fluid flow behaviour in multiple square perforated twisted tape with square wing inserts heat exchanger tube. Heat Mass Transf 1:1–14  https://doi.org/10.1007/s00231-018-2290-x
  18. 18.
    Pongsoi P, Pikulkajorn S, Wongwises S (2012) Effect of fin pitches on the optimum heat transfer performance of crimped spiral fin-and-tube heat exchangers. Int J Heat Mass Transf 55:6555–6566CrossRefMATHGoogle Scholar
  19. 19.
    Pongsoi P, Pikulkajorn S, Wang C-C, Wongwises S (2012) Effect of number of tube rows on the air-side performance of crimped spiral fin-and-tube heat exchanger with a multipass parallel and counter cross-flow configuration. Int J Heat Mass Transf 55:1403–1411CrossRefMATHGoogle Scholar
  20. 20.
    Pongsoi P, Promoppatum P, Pikulkajorn S, Wongwises S (2013) Effect of fin pitches on the air-side performance of L-footed spiral fin-and-tube heat exchangers. Int J Heat Mass Transf 59:75–82CrossRefGoogle Scholar
  21. 21.
    Du X, Zeng M, Dong Z, Wang Q (2014) Experimental study of the effect of air inlet angle on the air-side performance for cross-flow finned oval-tube heat exchangers. Exp Thermal Fluid Sci 52:146–155CrossRefGoogle Scholar
  22. 22.
    Dong J, Su L, Chen Q, Xu W (2013) Experimental study on thermal–hydraulic performance of a wavy fin-and-flat tube aluminum heat exchanger. Appl Therm Eng 51:32–39CrossRefGoogle Scholar
  23. 23.
    Liu L, Ling X, Peng H (2013) Complex turbulent flow and heat transfer characteristics of tubes with internal longitudinal plate-rectangle fins in EGR cooler. Appl Therm Eng 54:145–152CrossRefGoogle Scholar
  24. 24.
    Ismail MF, Hasan MN, Ali M (2014) Numerical simulation of turbulent heat transfer from perforated plate-fin heat sinks. Heat Mass Transf 50(4):509–519CrossRefGoogle Scholar
  25. 25.
    Kumar A, Joshi JB, Nayak AK, Vijayan PK (2016) 3D CFD simulations of air cooled condenser-II: Natural draft around a single finned tube kept in a small chimney. Int J Heat Mass Transf 92:507–522CrossRefGoogle Scholar
  26. 26.
    Odabaee M, Hooman K (2012) Metal foam heat exchangers for heat transfer augmentation from a tube bank. Appl Therm Eng 36:456–463CrossRefGoogle Scholar
  27. 27.
    Wais P (2016) Influence of fin thickness and winglet orientation on mass and thermal efficiency of cross-flow heat exchanger. Appl Therm Eng 102:184–195CrossRefGoogle Scholar
  28. 28.
    Bilirgen H, Dunbar S, Levy EK (2013) Numerical modeling of finned heat exchangers. Appl Therm Eng 61:278–288CrossRefGoogle Scholar
  29. 29.
    Cléirigh CTÓ, Smith WJ (2014) Can CFD accurately predict the heat-transfer and pressure-drop performance of finned-tube bundles? Appl Therm Eng 73:681–690CrossRefGoogle Scholar
  30. 30.
    Łopata S, Ocłoń P (2015) Numerical study of the effect of fouling on local heat transfer conditions in a high-temperature fin-and-tube heat exchanger. Energy 92:100–116CrossRefGoogle Scholar
  31. 31.
    Peng H, Liu L, Ling X, Li Y (2016) Thermo-hydraulic performances of internally finned tube with a new type wave fin arrays. Appl Therm Eng 98:1174–1188CrossRefGoogle Scholar
  32. 32.
    Szajding A, Telejko T, Straka R, Gołdasz A (2013) Experimental and numerical determination of heat transfer coefficient between oil and outer surface of monometallic tubes finned on both sides with twisted internal longitudinal fins. Int J Heat Mass Transf 58:395–401CrossRefGoogle Scholar
  33. 33.
    Tang L, Zeng M, Wang Q (2009) Experimental and numerical investigation on air-side performance of fin-and-tube heat exchangers with various fin patterns. Exp Thermal Fluid Sci 33:818–827CrossRefGoogle Scholar
  34. 34.
    De Schampheleire S, De Jaeger P, Reynders R, De Kerpel K, Ameel B, T'Joen C, Huisseune H, Lecompte S, De Paepe M (2013) Experimental study of buoyancy-driven flow in open-cell aluminium foam heat sinks. Appl Therm Eng 59:30–40CrossRefGoogle Scholar
  35. 35.
    Wang C-C, Chang Y-J, Hsieh Y-C, Lin Y-T (1996) Sensible heat and friction characteristics of plate fin-and-tube heat exchangers having plane fins. Int J Refrig 19:223–230CrossRefGoogle Scholar
  36. 36.
    Nuntaphan A, Kiatsiriroat T, Wang C (2005) Heat transfer and friction characteristics of crimped spiral finned heat exchangers with dehumidification. Appl Therm Eng 25:327–340CrossRefGoogle Scholar
  37. 37.
    Kundu B, Lee K-S (2014) Analytical tools for calculating the maximum heat transfer of annular stepped fins with internal heat generation and radiation effects. Energy 76:733–748CrossRefGoogle Scholar
  38. 38.
    Nuntaphan A, Vithayasai S, Kiatsiriroat T, Wang C-C (2007) Effect of inclination angle on free convection thermal performance of louver finned heat exchanger. Int J Heat Mass Transf 50:361–366CrossRefGoogle Scholar
  39. 39.
    Xie G, Wang Q, Sunden B (2009) Parametric study and multiple correlations on air-side heat transfer and friction characteristics of fin-and-tube heat exchangers with large number of large-diameter tube rows. Appl Therm Eng 29:1–16CrossRefGoogle Scholar
  40. 40.
    Tao Y, He Y, Huang J, Wu Z, Tao W (2007) Three-dimensional numerical study of wavy fin-and-tube heat exchangers and field synergy principle analysis. Int J Heat Mass Transf 50:1163–1175CrossRefMATHGoogle Scholar
  41. 41.
    Karmo D, Ajib S, Al Khateeb A (2013) New method for designing an effective finned heat exchanger. Appl Therm Eng 51:539–550CrossRefGoogle Scholar
  42. 42.
    Liu L, Fan Y, Ling X, Peng H (2013) Flow and heat transfer characteristics of finned tube with internal and external fins in air cooler for waste heat recovery of gas-fired boiler system. Chem Eng Process Process Intensif 74:142–152CrossRefGoogle Scholar
  43. 43.
    Kiatpachai P, Pikulkajorn S, Wongwises S (2015) Air-side performance of serrated welded spiral fin-and-tube heat exchangers. Int J Heat Mass Transf 89:724–732CrossRefGoogle Scholar
  44. 44.
    Kirsch KL, Thole KA (2017) Pressure loss and heat transfer performance for additively and conventionally manufactured pin fin arrays. Int J Heat Mass Transf 108(Part B):2502–2513CrossRefGoogle Scholar
  45. 45.
    Yaïci W, Ghorab M, Entchev E (2016) 3D CFD study of the effect of inlet air flow maldistribution on plate-fin-tube heat exchanger design and thermal–hydraulic performance. Int J Heat Mass Transf 101:527–541CrossRefGoogle Scholar
  46. 46.
    Chen H-T, Chiu Y-J, Liu C-S, Chang J-R (2017) Numerical and experimental study of natural convection heat transfer characteristics for vertical annular finned tube heat exchanger. Int J Heat Mass Transf 109:378–392CrossRefGoogle Scholar
  47. 47.
    Liu X, Yu J, Yan G (2016) A numerical study on the air-side heat transfer of perforated finned-tube heat exchangers with large fin pitches. Int J Heat Mass Transf 100:199–207CrossRefGoogle Scholar
  48. 48.
    Nellis G, Klein S (2009) ebrary Inc, Heat transfer. Cambridge University Press, CambridgeMATHGoogle Scholar
  49. 49.
    Chen H-T, Hsu W-L (2008) Estimation of heat-transfer characteristics on a vertical annular circular fin of finned-tube heat exchangers in forced convection. Int J Heat Mass Transf 51:1920–1932CrossRefMATHGoogle Scholar
  50. 50.
    Kline SJ, McClintock FA (1953) Describing uncertainties in single- sample experiments. Mech Eng 75:3–8Google Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Engineering FacultyShahrekord UniversityShahrekordIran
  2. 2.Department of Mechanical Engineering, Najafabad BranchIslamic Azad UniversityNajafabadIran

Personalised recommendations