Advertisement

The kinetics of wooden bilayers is not affected by different wood adhesive systems

  • C. Vailati
  • M. Rüggeberg
  • I. Burgert
  • P. Hass
Original
  • 22 Downloads

Abstract

The bending of wooden bilayers in response to the change of relative humidity can be utilized to build autonomous actuation devices. For bending, the properties of the adhesive may play a crucial role in terms of humidity transfer and mechanical performance. Hence, the type of the adhesive may have an impact on the bilayer responsiveness upon humidity changes. In this study, bilayers with various sizes were fabricated and glued with five different adhesives. The same samples were exposed at first to a single desorption phase for 48 h and in a second experiment to ten de-/adsorption cycles with a cycle length of 24 h. The initial moisture contents (MC) of the bilayers differed depending on the type of adhesive. Due to the additional water uptake of the wood layers bonded with water introducing adhesives (PVAC, MUF and PRF), these bilayers had a higher initial MC than those bonded with non-water introducing adhesives (PUR and Epoxy). During the de-/adsorption cycles, the overall amplitude of bending stayed relatively constant. However, the start- and the endpoints of the movement were shifted in the first three cycles, since here, the cycle length was not sufficiently long to reach an equilibrated MC state. However, after this initial adjustment phase, the bending of the wooden bilayers was reversible and repeatable. No significant differences in the kinetics of bilayers manufactured with the different adhesive systems could be observed. Thus, the specific adhesive properties do not seem to influence the responsiveness and performance of the wooden bilayers.

Notes

Acknowledgements

This work was funded by the Deutsche Forschungsgemeinschaft (DFG) priority program SPP 1420: “Biomimetic Materials Research: Functionality by Hierarchical Structuring of Materials” and by the Swiss National Foundation (SNF) Project 163191 “Smart shape-changing wood elements for improved energy efficiency of buildings” which is gratefully acknowledged. We would like to thank Sanja Kostic for the suggestion of the epoxy adhesive components ratio. Furthermore, the following persons are acknowledged as well: Thomas Schnider for cutting the spruce and beech samples, Marie Claire Graf for the help during the sample manufacturing and Erik Bachtiar for support during writing of the MATLAB code.

Supplementary material

226_2018_1046_MOESM1_ESM.pdf (423 kb)
Supplementary material 1 (PDF 423 kb)

References

  1. Correa D, Papadopoulou A, Guberan C, Jhaveri N, Reichert S, Menges A, Tibbits S (2015) 3D-printed wood: programming hygroscopic material transformations. 3D Print Addit Manuf 2(3):106–116CrossRefGoogle Scholar
  2. Faruk O, Bledzki AK, Fink H-P, Sain M (2012) Biocomposites reinforced with natural fibers: 2000–2010. Prog Polym Sci 37(11):1552–1596CrossRefGoogle Scholar
  3. Holstov A, Bridgens B, Farmer G (2015) Hygromorphic materials for sustainable responsive architecture. Constr Build Mater 98:570–582CrossRefGoogle Scholar
  4. Holstov A, Farmer G, Bridgens B (2017) Sustainable materialisation of responsive architecture. Sustainability 9(3):435CrossRefGoogle Scholar
  5. Kempaiah R, Nie Z (2014) From nature to synthetic systems: shape transformation in soft materials. J Mater Chem B 2(17):2357–2368CrossRefGoogle Scholar
  6. Kläusler O, Clauß S, Lübke L, Trachsel J, Niemz P (2013) Influence of moisture on stress–strain behaviour of adhesives used for structural bonding of wood. Int J Adhes Adhes 44:57–65CrossRefGoogle Scholar
  7. Loonen RCGM, Trčka M, Cóstola D, Hensen JLM (2013) Climate adaptive building shells: state-of-the-art and future challenges. Renew Sustain Energy Rev 25:483–493CrossRefGoogle Scholar
  8. Ozyhar T, Hering S, Niemz P (2013) Moisture-dependent orthotropic tension-compression asymmetry of wood. Holzforschung 67(4):395–404Google Scholar
  9. Raftery GM, Harte AM, Rodd PD (2009) Bond quality at the FRP–wood interface using wood-laminating adhesives. Int J Adhes Adhes 29(2):101–110CrossRefGoogle Scholar
  10. Reichert S, Menges A, Correa D (2015) Meteorosensitive architecture: biomimetic building skins based on materially embedded and hygroscopically enabled responsiveness. Comput Aided Des 60:50–69CrossRefGoogle Scholar
  11. Ross RJ (2010) Wood handbook: wood as an engineering material. USDA Forest Service, Forest Products Laboratory, General Technical Report FPL-GTR-190, 509 p, 1 v, 72Google Scholar
  12. Rüggeberg M, Burgert I (2015) Bio-inspired wooden actuators for large scale applications. PLoS ONE 10(4):e0120718.  https://doi.org/10.1371/journal.pone.0120718 CrossRefPubMedPubMedCentralGoogle Scholar
  13. Steiger R, Arnold M (2009) Strength grading of Norway spruce structural timber: revisiting property relationships used in EN 338 classification system. Wood Sci Technol 43(3–4):259–278CrossRefGoogle Scholar
  14. Subramanian RV (1984) Chemistry of adhesion. In: Rowell RM (ed) The chemistry of solid wood, vol 207. American Chemical Society, Seattle, pp 323–348CrossRefGoogle Scholar
  15. Timoshenko S (1925) Analysis of bi-metal thermostats. JOSA 11(3):233–255CrossRefGoogle Scholar
  16. Vailati C, Hass P, Burgert I, Rüggeberg M (2017) Upscaling of wood bilayers: design principles for controlling shape change and increasing moisture change rate. Mater Struct 50(6):250CrossRefGoogle Scholar
  17. Vailati C, Bachtiar E, Hass P, Burgert I, Rüggeberg M (2018) An autonomous shading system based on coupled wood bilayer elements. Energy Build 158:1013–1022CrossRefGoogle Scholar
  18. Wimmer R, Kläusler O, Niemz P (2013) Water sorption mechanisms of commercial wood adhesive films. Wood Sci Technol 47(4):763–775CrossRefGoogle Scholar
  19. Wood DM, Correa D, Krieg OD, Menges A (2016) Material computation—4D timber construction: towards building-scale hygroscopic actuated, self-constructing timber surfaces. Int J Archit Comput 14(1):49–62CrossRefGoogle Scholar
  20. Yamin F (2012) Climate change and carbon markets: a handbook of emissions reduction mechanisms. Routledge, LondonCrossRefGoogle Scholar
  21. Zhou A, Tam L-h YuZ, Lau D (2015) Effect of moisture on the mechanical properties of CFRP–wood composite: an experimental and atomistic investigation. Compos B Eng 71:63–73CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  • C. Vailati
    • 1
    • 2
  • M. Rüggeberg
    • 1
    • 2
  • I. Burgert
    • 1
    • 2
  • P. Hass
    • 1
    • 2
  1. 1.Institute for Building Materials (IfB)ETH ZurichZurichSwitzerland
  2. 2.Laboratory of Applied Wood MaterialsEMPADübendorfSwitzerland

Personalised recommendations