Advertisement

Influences of postproduction heat treatments on the material anisotropy of nickel-aluminum bronze fabricated using wire-arc additive manufacturing process

  • Chen Shen
  • Gang Mu
  • Xueming HuaEmail author
  • Fang Li
  • Dongzhi Luo
  • Xiangru Ji
  • Chi Zhang
ORIGINAL ARTICLE
  • 54 Downloads

Abstract

The anisotropy of wire-arc additively deposited nickel-aluminum bronze alloy is studied by microstructure observation and room temperature mechanical property testing. The applied heat treatments have effectively modified the as-fabricated {0 1 1} <2 1 1>, {1 1 1} <1 1 0> texture into {1 1 1}. According to the microstructures, the single tempering has resulted in lowest anisotropy while heat treatment with prior homogenization and quenching process induces even intensified annealing textures. However, as shown by the tensile tests, the quenching process is necessary for favorable mechanical properties in the wire-arc additive manufacturing fabricated nickel-aluminum bronze component; therefore, a balance between homogenization annealing and κ-phase precipitation is indicated. Meanwhile, the function of κ-phase precipitates on grain rotation and growth during post-production heat treatment is explained in detail.

Keywords

Nickel-aluminum bronze Additive manufacturing Anisotropy Grain orientation Heat treatment 

Notes

Acknowledgments

Gratitude is also due to the Instrumental Analysis Center of Shanghai Jiao Tong University for the microstructure tests.

Funding information

The authors acknowledge the support of the National Key Research and Development Program of China [Grant No.: 2016YFB0301205] and “Sailing Program” of Shanghai Science and Technology Committee [Grant No.: 19YF1422700].

References

  1. 1.
    Jahanafrooz A, Hasan F, Lorimer GW, Ridley N (1983) Microstructural development in complex nickel-aluminum bronzes. Metall Trans A 14:1951–1956CrossRefGoogle Scholar
  2. 2.
    Tan KS, Wharton JA, Wood RJK (2005) Solid particle erosion–corrosion behaviour of a novel HVOF nickel aluminium bronze coating for marine applications—correlation between mass loss and electrochemical measurements. Wear 258:629–640CrossRefGoogle Scholar
  3. 3.
    Barik RC, Wharton JA, Wood RJK, Tan KS, Stokes KR (2005) Erosion and erosion–corrosion performance of cast and thermally sprayed nickel–aluminium bronze. Wear 259:230–242CrossRefGoogle Scholar
  4. 4.
    Liu Y, Mochel ME, Mazumder J, Shibata K (1994) TEM study of precipitates in laser clad Ni Al bronze. Acta Metall Mater 42:1763–1768CrossRefGoogle Scholar
  5. 5.
    Ferrara RJ, Caton T (1982) Review of dealloying of cast aluminum bronze and nickel-aluminum bronze alloys in sea water service. Mater Perform 21:30–34Google Scholar
  6. 6.
    Culpan EA, Rose G (1978) Microstructural characterization of cast nickel aluminium bronze. J Mater Sci 13:1647–1657CrossRefGoogle Scholar
  7. 7.
    Olszewski AM (2008) Dealloying of a nickel–aluminum bronze impeller. J Fail Anal Prevent 8:505–508CrossRefGoogle Scholar
  8. 8.
    Al-Hashem A, Cacer PG, Riad WT, Shalaby HM (1995) Cavitation corrosion behavior of cast nickel-aluminum bronze in seawater. Corrosion 51:331–342CrossRefGoogle Scholar
  9. 9.
    Tang CH, Cheng FT, Man HC (2004) Effect of laser surface melting on the corrosion and cavitation erosion behaviors of a manganese–nickel–aluminium bronze. Mater Sci Eng A 373:195–203CrossRefGoogle Scholar
  10. 10.
    Hyatt CV, Magee KH, Betancourt T (1998) The effect of heat input on the microstructure and properties of nickel aluminum bronze laser clad with a consumable of composition Cu-9.0 Al-4.6 Ni-3.9 Fe-1.2 Mn. Metal Mater Trans A 29:1677–1690CrossRefGoogle Scholar
  11. 11.
    Hanke S, Fischer A, Beyer M, Dos-Santos J (2011) Cavitation erosion of NiAl-bronze layers generated by friction surfacing. Wear 273:32–37CrossRefGoogle Scholar
  12. 12.
    Frazier WE (2014) Metal additive manufacturing: a review. J Mater Eng Perform 23:1917–1928CrossRefGoogle Scholar
  13. 13.
    Ding D, Pan Z, Cuiuri D, Li H (2015) A practical path planning methodology for wire and arc additive manufacturing of thin-walled structures. Robot Cim-int Manuf 34:8–19CrossRefGoogle Scholar
  14. 14.
    Ding D, Pan Z, Cuiuri D, Li H (2015) A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM). Robot Cim-int Manuf 31:101–110CrossRefGoogle Scholar
  15. 15.
    Ding D, Pan Z, Cuiuri D, Li H (2015) Wire-feed additive manufacturing of metal components: technologies, developments and future interests. Int J Adv Manuf Tech 81:465–481CrossRefGoogle Scholar
  16. 16.
    Wang F, Williams S, Rush M (2011) Morphology investigation on direct current pulsed gas tungsten arc welded additive layer manufactured Ti6Al4V alloy. Int J Adv Manuf Tech 57:597–603CrossRefGoogle Scholar
  17. 17.
    Brandl E, Michailov V, Viehweger B, Leyens C (2011) Deposition of Ti-6Al-4 V using laser and wire, part I: microstructural properties of single beads. Surf Coat Technol 206:1130–1141CrossRefGoogle Scholar
  18. 18.
    Ma Y (2015) Fabrication of gamma titanium aluminide alloys by gas tungsten arc welding-based additive layer manufacturing. University of WollongongGoogle Scholar
  19. 19.
    Shen C, Pan Z, Ma Y, Cuiuri D, Li H (2015) Fabrication of iron-rich Fe–Al intermetallics using the wire-arc additive manufacturing process. Addit Manuf 7:20–26CrossRefGoogle Scholar
  20. 20.
    Shen C, Pan Z, Cuiuri D, Roberts J, Li H (2016) Fabrication of Fe-Fe-Al funtionally graded material using the wire-arc additive manufacturing process. Metal Mater Trans B 47:763–772CrossRefGoogle Scholar
  21. 21.
    Dong B, Pan Z, Shen C, Ma Y, Li H (2017) Fabrication of copper-rich Cu-Al alloy using the wire-arc additive manufacturing process. Metal Mater Trans B 48:3143–3151CrossRefGoogle Scholar
  22. 22.
    Ding D, Pan Z, van Duin S, Li H, Shen C (2016) Fabricating superior nial bronze components through wire arc additive manufacturing. Materials 9:652CrossRefGoogle Scholar
  23. 23.
    Shen C, Pan Z, Cuiuri D, Dong B, Li H (2016) In-depth study of the mechanical properties for Fe3Al based iron aluminide fabricated using the wire-arc additive manufacturing process. Mater Sci Eng A 669:118–126CrossRefGoogle Scholar
  24. 24.
    Shen C, Pan Z, Ding D, Lei Y, Nie N, Luo D, Cuiuri D, van Duin S, Li H (2018) The influence of post-production heat treatment on the multi-directional properties of nickel-aluminum bronze alloy fabricated using wire-arc additive manufacturing process. Addit Manuf 23:411–421CrossRefGoogle Scholar
  25. 25.
    Shen C, Pan Z, Cuiuri D, van Duin S, Luo D, Dong B, Li H (2018) Influences of postproduction heat treatment on Fe3Al-based iron aluminide fabricated using the wire-arc additive manufacturing process. Int J Adv Manuf Technol 97:335–344CrossRefGoogle Scholar
  26. 26.
    Torrado AR, Shemelya CM, English JD, Lin Y, Wicker RB, Roberson DA (2015) Characterizing the effect of additives to ABS on the mechanical property anisotropy of specimens fabricated by material extrusion 3D printing. Addit Manuf 6:16–29CrossRefGoogle Scholar
  27. 27.
    Quan Z, Wu A, Keefe M, Qin X, Yu J, Suhr J, Byun JH, Kim BS, Chou TW (2015) Additive manufacturing of multi-directional preforms for composites: opportunities and challenges. Mater Today 18:503–512CrossRefGoogle Scholar
  28. 28.
    Popovich VA, Borisov EV, Popovich AA, Sufiiarov VS, Masaylo DV, Alzina L (2017) Functionally graded Inconel 718 processed by additive manufacturing: crystallographic texture, anisotropy of microstructure and mechanical properties. Mater Des 114:441–449CrossRefGoogle Scholar
  29. 29.
    Carroll BE, Palmer TA, Beese AM (2015) Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing. Acta Mater 87:309–320CrossRefGoogle Scholar
  30. 30.
    Zhu Y, Liu D, Tian X, Tang H, Wang H (2014) Characterization of microstructure and mechanical properties of laser melting deposited Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si titanium alloy. Mater Des 56:445–453CrossRefGoogle Scholar
  31. 31.
    Zhu Y, Tian X, Li J, Wang H (2015) The anisotropy of laser melting deposition additive manufacturing Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si titanium alloy. Mater Des 67:538–542CrossRefGoogle Scholar
  32. 32.
    Kaplan M, Yildiz A (2003) The effects of production methods on the microstructures and mechanical properties of an aluminum bronze. Mater Lett 57:4402–4411CrossRefGoogle Scholar
  33. 33.
    McKamey CG (1996) Iron aluminides. In: Physical metallurgy and processing of intermetallic compounds. Springer, Boston, pp 351–391CrossRefGoogle Scholar
  34. 34.
    Yuan W, Mishra RS, Carlson B, Mishra RK, Verma R, Kubic R (2011) Effect of texture on the mechanical behavior of ultrafine grained magnesium alloy. Scr Mater 64:580–583CrossRefGoogle Scholar
  35. 35.
    Faurie D, Renalt PO, Le Bourhis E, Goudeau P (2006) Study of texture effect on elastic properties of Au thin films by X-ray diffraction and in situ tensile testing. Acta Mater 54:4503–4513CrossRefGoogle Scholar
  36. 36.
    Hoseini M, Shahryari A, Omanovic S, Szpunar JA (2009) Comparative effect of grain size and texture on the corrosion behaviour of commercially pure titanium processed by equal channel angular pressing. Corros Sci 51:3064–3067CrossRefGoogle Scholar
  37. 37.
    Wu L, Agnew SR, Ren Y, Brown DW, Clausen B, Stoica GM, Wenk HR, Liaw PK (2010) The effects of texture and extension twinning on the low-cycle fatigue behavior of a rolled magnesium alloy, AZ31B. Mater Sci Eng A 527:7057–7067CrossRefGoogle Scholar
  38. 38.
    Pal S, Lojen G, Kokol V, Drstvensek I (2018) Evolution of metallurgical properties of Ti-6Al-4V alloy fabricated in different energy densities in the selective laser melting technique. J Manuf Process 35:538–546CrossRefGoogle Scholar
  39. 39.
    Wang L, Teng J, Liu P, Hirata A, Ma E, Zhang Z, Chen M, Han X (2014) Grain rotation mediated by grain boundary dislocations in nanocrystalline platinum. Nat Commun 5:4402CrossRefGoogle Scholar
  40. 40.
    Allen CW, Rehn LE (1989) Irradiation-induced grain growth: role of dislocations. MRS Online Proceedings Library Archive 157Google Scholar
  41. 41.
    Zhang Y, Tucker GJ, Trelewicz JR (2017) Stress-assisted grain growth in nanocrystalline metals: grain boundary mediated mechanisms and stabilization through alloying. Acta Mater 131:39–47CrossRefGoogle Scholar
  42. 42.
    Feltham P (1957) Grain growth in metals. Acta Metall 5:97–105CrossRefGoogle Scholar
  43. 43.
    Kacher J, Robertson IM, Nowell M, Knapp J, Hattar K (2011) Study of rapid grain boundary migration in a nanocrystalline Ni thin film. Mater Sci Eng A 528:1628–1635CrossRefGoogle Scholar
  44. 44.
    Bozzolo N, Agnoli A, Souai N, Bernacki M, Loge RE (2013) Strain induced abnormal grain growth in nickel base superalloys. Mater Sci Forum 753:321–324CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  • Chen Shen
    • 1
    • 2
  • Gang Mu
    • 1
  • Xueming Hua
    • 1
    Email author
  • Fang Li
    • 1
  • Dongzhi Luo
    • 2
    • 3
  • Xiangru Ji
    • 1
  • Chi Zhang
    • 1
  1. 1.Shanghai Key Lab of Materials Laser Processing and Modification, School of Materials Science and EngineeringShanghai Jiao Tong UniversityShanghaiChina
  2. 2.School of Mechanical, Materials and Mechatronics Engineering, Faculty of Engineering and Information SciencesUniversity of WollongongWollongongAustralia
  3. 3.Technical Institute of Ordnance Industry, School of Electrical and Electronic EngineeringChongqing Electromechanical Vocational InstitutionChongqingChina

Personalised recommendations