Advertisement

A thermomechanical analysis leading to a novel flank face design providing longer tool lives for tools used in the drilling of Inconel 718

  • Ekrem OezkayaEmail author
  • Milan Bücker
  • Simon Strodick
  • Dirk Biermann
ORIGINAL ARTICLE
  • 4 Downloads

Abstract

Inconel 718 is a versatile material due to its excellent properties. However, machining and in particular drilling of Inconel 718 present great challenges for the tools. In order to increase process reliability and tool life, a novel modification for the applied drilling tools was developed. It consists of a flank face retraction behind the cutting edge which is created by grinding. While regular drilling tools feature a continuous flank face on the tool tip, the retraction provides a minimized frictional surface between the tool tip and the bore hole ground. Furthermore, computational fluid dynamics simulations have shown that the created vacuous volume behind the cutting edge becomes filled with cutting fluid during the drilling process. The described effects result in longer tool lives which could be shown in experimental investigations. This paper presents the conducted experiments in which both the occurring mechanical and thermal loads were examined in order to determine the radius-dependent thermomechanical loads along the cutting edge. The results have shown that an increase in either cutting speed or feed result in significantly higher temperatures at the cutting edge corners while temperatures at the inner diameter of the tool remained almost constant. At the same time, a rise in feed leads to notably higher mechanical loads along the whole cutting edge. In addition, reference tool life tests were conducted using standard tools and under variation of the cutting values. The resulting tool wear as well as the tool-workpiece contact zones were investigated in detail. The gathered findings were then used to develop a flank face modification whose sufficient thermomechanical stability was ensured by FEM simulations. Afterwards, the new tool design was applied to drilling tools and then validated in field tests. The results show that a considerably higher drilling distance as well as lower tool wear and thus a longer tool life could be achieved with the modified drills.

Keywords

Drilling Inconel 718 Pyrometry FEM simulation Thermal simulation 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding information

This work was supported by the German Research Foundation (DFG) [BI 498/87-1].

Compliance with ethical standards

Conflict of interest

The authors declare that they have no conflict of interest.

References

  1. 1.
    Barker JF (1989) The initial years of alloy 718—a G.E. perspective. In: Loria, Edward a.: Superalloy 718, Warrendale, pp 269–277Google Scholar
  2. 2.
    Furrer D, Fecht H (1999) Ni-based superalloys for turbine discs. JOM-J MIN MET MAT S 51:14–17.  https://doi.org/10.1007/s11837-999-0005-y CrossRefGoogle Scholar
  3. 3.
    Kolts J (1989) Alloy 718 for the oil and gas industry. In Loria, Edward a.: Superalloy 718, Warrendale, pp. 329–344Google Scholar
  4. 4.
    Royce R (2018) World’s most efficient large aero-engine. https://www.rolls-royce.com/. Accessed 6 Feb 2018
  5. 5.
    Barthelmä F, Frank H, Schiffler M, Bartsch A (2016) Hard coatings to improve the machining of nickel based materials. Proc CIRP 46:294–298.  https://doi.org/10.1016/j.procir.2016.04.069 CrossRefGoogle Scholar
  6. 6.
    Thakur A, Gangopadhyay S (2016) State-of-the-art in surface integrity in machining of nickel-based super alloys. Int J Mach Tool Manu 100:25–54.  https://doi.org/10.1016/j.ijmachtools.2015.10.001 CrossRefGoogle Scholar
  7. 7.
    Ulutan D, Ozel T (2011) Machining induced surface integrity in titanium and nickel alloys. I Int J Mach Tool Manu 51:250–280.  https://doi.org/10.1016/j.ijmachtools.2010.11.003 CrossRefGoogle Scholar
  8. 8.
    Klocke F (2011) Manufacturing processes 1—cutting. Springer-Verlag, Berlin HeidelbergCrossRefGoogle Scholar
  9. 9.
    Amran MA, Salmah S, Hussein NIS, Izamshah R, Hadzley M, Sivaros S, Kasim MS, Sulaiman MA (2013) Effects of machine parameters on surface roughness using response surface method in drilling process. Procedia Eng 68:24–29.  https://doi.org/10.1016/j.proeng.2013.12.142 CrossRefGoogle Scholar
  10. 10.
    Beer N, Oezkaya E, Biermann D (2014) Drilling of Inconel 718 with geometry-modified twist drills. Proc CIRP 9:49–55.  https://doi.org/10.1016/j.procir.2014.07.124 CrossRefGoogle Scholar
  11. 11.
    Oezkaya E, Beer N, Biermann D (2016) Experimental studies and CFD simulation of the internal cooling conditions when drilling Inconel 718. Int J Mach Tool Manu 108:52–65.  https://doi.org/10.1016/j.ijmachtools.2016.06.003 CrossRefGoogle Scholar
  12. 12.
    Kasim MS, Haron CHC, Ghani JA, Azam MA, Izamshah R, Ali MAM, Aziz MSA (2014) The influence of cutting parameter on heat generation in high-speed milling Inconel 718 under MQL condition. J Sci Ind Res India 73:62–65Google Scholar
  13. 13.
    Dudzinski D, Devillez A, Moufki A, Larrouquère D, Zerrouki V, Vigneau J (2004) A review of developments towards dry and high speed machining of Inconel 718 alloy. Int J Mach Tool Manu 44:439–456.  https://doi.org/10.1016/S0890-6955(03)00159-7 CrossRefGoogle Scholar
  14. 14.
    M'Saoubi R, Axinte D, Soo SL, Nobel C, Attia H, Kappmeyer G, Engin S, Sim WM (2015) High performance cutting of advanced aerospace alloys and composite materials. Cirp Ann-Manuf Tech 64:557–580.  https://doi.org/10.1016/j.cirp.2015.05.002 CrossRefGoogle Scholar
  15. 15.
    Díaz-Álvarez J, Tapetado A, Vázquez C, Miguélez H (2017) Temperature measurement and numerical prediction in machining Inconel 718. Sensors (Basel, Switzerland) 17.  https://doi.org/10.3390/s17071531
  16. 16.
    Krzysztof L, Kosmol J (2010) Temperature identivication of drilling process using thermovision methods. 14th International Research/Expert Conference (TMT 2010, Mediterranean Cruise, 11–18 September 2010), pp. 25–28Google Scholar
  17. 17.
    Tönshoff HK, Denkena B (2013) Basics of cutting and abrasive processes. Springer-Verlag, Berlin HeidelbergCrossRefGoogle Scholar
  18. 18.
    Li R, Shih AJ (2007) Spiral point drill temperature and stress in high-throughput drilling of titanium. Int J Mach Tool Manu 47:2005–2017.  https://doi.org/10.1016/j.ijmachtools.2007.01.014 CrossRefGoogle Scholar
  19. 19.
    Bagci E, Ozcelik B (2007) Effects of different cooling conditions on twist drill temperature. Int J Adv Manuf Tech 34:867–877.  https://doi.org/10.1007/s00170-006-0668-2 CrossRefGoogle Scholar
  20. 20.
    Davies MA, Ueda T, M'Saoubi R, Mullany B, Cooke AL (2007) On the measurement of temperature in material removal processes. CIRP Ann-Manuf Tech 56:581–604.  https://doi.org/10.1016/j.cirp.2007.10.009 CrossRefGoogle Scholar
  21. 21.
    Brosse A, Naisson P, Hamdi H, Bergheau JM (2008) Temperature measurement and heat flux characterization in grinding using thermography. J Mater Process Tech 201:590–595.  https://doi.org/10.1016/j.jmatprotec.2007.11.267 CrossRefGoogle Scholar
  22. 22.
    Ueda T, Sato M, Hosokawa A, Ozawa M (2008) Development of infrared radiation pyrometer with optical fibers—two-color pyrometer with non-contact fiber coupler. CIRP Ann-Manuf Tech 57:69–72.  https://doi.org/10.1016/j.cirp.2008.03.056 CrossRefGoogle Scholar
  23. 23.
    Müller B, Renz U (2001) Development of a fast fiber-optic two-color pyrometer for the temperature measurement of surfaces with varying emissivities. Rev Sci Instrum 72:3366–3374.  https://doi.org/10.1063/1.1384448 CrossRefGoogle Scholar
  24. 24.
    Denkena B, Köhler J, Bergmann B (2015) Development of cutting edge geometries for hard milling operations. CIRP J Manuf Sci Technol 8:43–52.  https://doi.org/10.1016/j.cirpj.2014.10.002 CrossRefGoogle Scholar
  25. 25.
    Beno T, Hulling U (2012) Measurement of cutting edge temperature in drilling. Proc CIRP 3:531–536.  https://doi.org/10.1016/j.procir.2012.07.091 CrossRefGoogle Scholar
  26. 26.
    Thevenet J, Siroux M, Desmet B (2008) Brake disc surface temperature measurement using a fiber optic two-color pyrometer. 9th International Conference on Quantitative InfraRed Thermography (July 2–5, 2008, Krakow - Poland)Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Institute of Machining TechnologyTU Dortmund UniversityDortmundGermany

Personalised recommendations