Advertisement

Application of CFD and vapor bubble dynamics for an efficient electro-thermal simulation of EDM: an integrated approach

  • Shirsendu DasEmail author
  • Swarup Paul
  • Biswanath Doloi
ORIGINAL ARTICLE
  • 15 Downloads

Abstract

Micro-chip removal and heat dissipation are two important and essential utilities of dielectric medium along with its vital contribution in plasma channel formation, which has a significant influence in metal removal, tool wear, and surface integrity. The vapor bubbles, which are formed after every progressive spark, expand and collapse in the electric field and finally condensed inside the dielectric medium. As the localized heat and excess temperature of the eroded spot increases, the dynamic properties of the bubbles accelerate and develop a lower pressure region, which is responsible for dielectric flushing. In this paper, the integrated approach of vapor bubble dynamics and computational fluid dynamics is used to study the dynamic behavior and heat dissipation of dielectric fluid through the plasma channel. At the very beginning of machining, the excess temperature is comparatively low; so, the detached bubbles are condensed inside the fluid medium and are not able to move above the free surface. However, as the temperature of the machined zone rises, excess temperature also increases and bubbles are able to carry the heat up to the free surface of the dielectric medium and finally condense. This phenomenon is very much analogous to the boiling process. Earlier, many simulation processes are used by researchers to investigate heat flux and heat dissipation rate of the dielectric fluid, but, here, vapor bubble dynamics and periodic heating are introduced to consider heat absorption by vapor bubbles, which gives more accurate heat transfer analysis of electric discharge machining. It is observed that the adopted model has the accuracy level of more than 95% with 4.5–4.6% of average prediction error and 1.5–2% more efficient than the existing models.

Keywords

Electro-thermal simulation Vapor bubble model CFD 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Khosrozadeh B, Shabgard M (2017) Effects of hybrid electrical discharge machining processes on surface integrity and residual stresses of Ti-6Al-4V titanium alloy. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-017-0601-x
  2. 2.
    Gadeschi GB, Schneider S, Mohammadnejad M, Meinke M, Klink A, Schröder W, Klocke F (2017) Numerical analysis of flushing-induced thermal cooling including debris transport in electrical discharge machining (EDM). Proc CIRP 58:116–121CrossRefGoogle Scholar
  3. 3.
    Hajizadeh Aghdam A, Khoo BC, Farhangmehr V, Shervani-Tabar MT (2015) Experimental study on the dynamics of an oscillating bubble in a vertical rigid tube. Exp Thermal Fluid Sci 60:299–307CrossRefGoogle Scholar
  4. 4.
    Shao B, Rajurkar KP (2015) Modelling of the crater formation in micro-EDM. Proc CIRP 33:376–381CrossRefGoogle Scholar
  5. 5.
    Alavi F, Jahan MP (2017) Optimization of process parameters in micro-EDM of Ti-6Al-4V based on full factorial design. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-017-0103-x
  6. 6.
    An’Yang X, Zhidong L, Wenpei L, Zongjun T, Mingbo Q (2014) Study of high-efficiency electrical discharge machining-induced ablation machining of titanium alloy TC4 using a multi-function electrode. Int J Adv Manuf Technol 72:377–385.  https://doi.org/10.1007/s00170-014-5654-5 CrossRefGoogle Scholar
  7. 7.
    Klocke F, Schneider S, Mohammadnejada M, Hensgena L, Klink A (2017) Inverse simulation of heat source in electrical discharge machining (EDM). Proc CIRP 58:1–6CrossRefGoogle Scholar
  8. 8.
    Liu JF, Guo YB (2016) Modeling of white layer formation in electric discharge machining (EDM) by incorporating massive random discharge characteristics. Proc CIRP 42:697–702CrossRefGoogle Scholar
  9. 9.
    Liu JF, Guo YB (2016) Residual stress modeling in electric discharge machining (EDM) by incorporating massive random discharges. Proc CIRP 45:299–302CrossRefGoogle Scholar
  10. 10.
    Nakharintr L, Naphon P (2017) Magnetic field effect on the enhancement of nano fluids heat transfer of a confined jet impingement in mini-channel heat sink. Int J Heat Mass Transf 110:753–759CrossRefGoogle Scholar
  11. 11.
    Mohantya CP, Sahub J, Mahapatra SS (2013) Thermal-structural analysis of electrical discharge machining process. Proc Eng 51:508–513CrossRefGoogle Scholar
  12. 12.
    Kuriachen B, Varghese A, Somashekhar KP, Panda S, Mathew J (2015) Three-dimensional numerical simulation of micro electric discharge machining of Ti-6Al-4V. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-015-6794-y
  13. 13.
    Gov K (2017) The effects of the dielectric liquid temperature on the hole geometries drilled by electro erosion. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-017-0231-3
  14. 14.
    Mohanty RL, Das MK (2017) A critical review on bubble dynamics parameters influencing boiling heat transfer. Renew Sust Energ Rev 78:466–494CrossRefGoogle Scholar
  15. 15.
    Allen P, Chen X (2007) Process simulation of micro electro-discharge machining on molybdenum. J Mater Process Technol 186:346–355CrossRefGoogle Scholar
  16. 16.
    Panda DK (2008) Study of thermal stresses induced surface damage under growing plasma channel in electro-discharge machining. J Mater Process Technol 202:86–95CrossRefGoogle Scholar
  17. 17.
    Yeo SH, Kurnia W, Tan PC (2008) Critical assessment and numerical comparison of electro-thermal models in EDM. J Mater Process Technol 203:241–251CrossRefGoogle Scholar
  18. 18.
    Snoeys R, Van Dijck FS (1971) Investigation of electro discharge machining operations by means of thermo-mathematical model. CIRP Ann 20:35–37Google Scholar
  19. 19.
    Van Dijck FS, Dutre WL (1974) Heat conduction model for the calculation of the volume of molten metal in electric discharges [discharge machining]. J Phys D Appl Phys 7:899–910CrossRefGoogle Scholar
  20. 20.
    Dibitonto DD, Eubank PT, Patel MR, Barrufet MA (1989) Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model. J Appl Phys 66:4095–4103CrossRefGoogle Scholar
  21. 21.
    Jilani ST, Pandey PC (1982) Analysis and modelling of EDM parameters. Precis Eng 4:215–221CrossRefGoogle Scholar
  22. 22.
    Beck JV (1981) Transient temperatures in a semi-infinite cylinder heated by a disk heat source. Int J Heat Mass Transf 24:1631–1640CrossRefGoogle Scholar
  23. 23.
    Shervani-Tabar MT, Rambarzin F, Shabgard MR, Payamani R (2011) Numerical study on the dynamics of an electrical discharge generated vapor bubble in EDM with different shapes of the tool and the work piece. Int J Adv Manuf Technol 56:151–159CrossRefGoogle Scholar
  24. 24.
    Zhang Y, Liu Y, Ji R, Zheng C, Shen Y, Wang X (2013) Transient dynamics simulation of the electrical discharge-generated bubble in sinking EDM. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-013-4969-y
  25. 25.
    Mishra DN, Bhatia A, Rana V Study on electro discharge machining (EDM). Int J Eng Sci 2319–1813 ISSN (p): 2319–1805Google Scholar
  26. 26.
    Das K, Acharya N, Kundu PK (2016) The onset of nano fluid flow past a convectively heated shrinking sheet in presence of heat source/sink: a Lie group approach. Appl Therm Eng 103:38–46CrossRefGoogle Scholar
  27. 27.
    Kukla S, Siedlecka U (2016) Fractional heat conduction in multilayer spherical bodies. J Appl Math Comput Mech 15:83–92MathSciNetCrossRefGoogle Scholar
  28. 28.
    Shen Y, Liu Y, Zhang Y, Tan B, Ji R, Cai B, Zheng C (2014) Determining the energy distribution during electric discharge machining of Ti–6Al–4V. Int J Adv Manuf Technol.  https://doi.org/10.1007/s00170-013-5194-4
  29. 29.
    Farhangmehr V, Hajizadeh Aghdam A, Shervani-Tabar MT, Parvizi R, Ohl SW, Khoo BC (2014) Numerical investigation on the pulsating bubble dynamics in a narrow cylinder with a compliant coating. Fluid Dyn Res 46:015513 27 ppMathSciNetCrossRefGoogle Scholar
  30. 30.
    Farhangmehr V, Shervani-Tabar MT, Parvizi R, Ohl SW, Khoo BC (2015) Numerical study on ring bubble dynamics in a narrow cylinder with a compliant coating. Fluid Dyn Res 47:025508 17 ppCrossRefGoogle Scholar
  31. 31.
    Carslaw HS, Jaeger JC (1986) Conduction of heat in solids, 2nd edn. Clarendon Press, OxfordzbMATHGoogle Scholar
  32. 32.
    Box GEP, Hunter JS, Hunter WG (2005) Statistics for experimenters: design, innovation, and discovery, 2nd edn. John Wiley & Sons, HobokenzbMATHGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Production Engineering DepartmentNational Institute of TechnologyAgartalaIndia
  2. 2.Production Engineering DepartmentJadavpur UniversityKolkataIndia

Personalised recommendations