Advertisement

Influence of external loading on the resonant frequency shift of ultrasonic assisted turning: numerical and experimental analysis

  • H. Puga
  • J. Grilo
  • F. J. Oliveira
  • R. F. Silva
  • A. V. Girão
ORIGINAL ARTICLE
  • 16 Downloads

Abstract

In this paper, a numerical and an experimental approach are established to study the influence of the machining parameters on the resonance frequency shift of ultrasonic assisted turning. The numerical model incorporates the mechanical and electrical effect on the simulation mode shape and resonance frequency of entire ultrasonic equipment. It is numerically shown that the machining parameters’ variability promotes a resonance frequency shifting, and the depth of cut is suggested to have more effect than the feed rate. Experimental results demonstrated that for the same cutting speed and different depth of cut and feed, the frequency value shifts thus compromise the surface quality. With the frequency adjustment promoted by MMM system, surface roughness improves 10 and 14%, when the feed is increased from 0.045 to 0.18 mm/rev, respectively, for a depth of cut of 1.5 mm.

Keywords

Ultrasonic assisted turning Finite element analysis Resonance frequency Surface roughness 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding information

This study was supported by FEDER/COMPETE funds and by national funds through FCT and was developed on the aim of the research Post-Doctoral grant SFRH/BPD/76680/2011. Also, this work has been supported by the FCT in the scope of the projects UID/EEA/04436/2013, by FEDER funds through the COMPETE 2020 –POCI with the reference project POCI-01-0145-FEDER-006941 and project CICECO - Aveiro Institute of Materials, POCI-01-0145-FEDER-007679 (FCT Ref. UID /CTM /50011/2013), financed by national funds through the FCT/MEC and when appropriate co-financed by FEDER under the PT2020 Partnership Agreement.

References

  1. 1.
    Grzesik W (2017) Machinability of engineering materials. In: Advanced machining processes of metallic materials. Elsevier, pp 241–264Google Scholar
  2. 2.
    Arun Kumar S, Yoganath VG, Krishna P (2018) Machinability of hardened alloy steel using cryogenic machining. Mater Today Proc 5:8159–8167.  https://doi.org/10.1016/j.matpr.2017.11.504 CrossRefGoogle Scholar
  3. 3.
    Parida AK, Maity K (2018) Comparison the machinability of Inconel 718, Inconel 625 and Monel 400 in hot turning operation. Eng Sci Technol Int J 21:364–370.  https://doi.org/10.1016/j.jestch.2018.03.018 CrossRefGoogle Scholar
  4. 4.
    Sajjady SA, Nouri Hossein Abadi H, Amini S, Nosouhi R (2016) Analytical and experimental study of topography of surface texture in ultrasonic vibration assisted turning. Mater Des 93:311–323.  https://doi.org/10.1016/j.matdes.2015.12.119 CrossRefGoogle Scholar
  5. 5.
    M’Saoubi R, Axinte D, Soo SL et al (2015) High performance cutting of advanced aerospace alloys and composite materials. CIRP Ann 64:557–580.  https://doi.org/10.1016/j.cirp.2015.05.002 CrossRefGoogle Scholar
  6. 6.
    Kumar J (2013) Ultrasonic machining - a comprehensive review. Mach Sci Technol 17:325–379.  https://doi.org/10.1080/10910344.2013.806093 CrossRefGoogle Scholar
  7. 7.
    Xu W-X, Zhang L-C (2015) Ultrasonic vibration-assisted machining: principle, design and application. Adv Manuf 3:173–192.  https://doi.org/10.1007/s40436-015-0115-4 CrossRefGoogle Scholar
  8. 8.
    Xu W, Zhang L, Wu Y (2016) Effect of tool vibration on chip formation and cutting forces in the machining of fiber-reinforced polymer composites. Mach Sci Technol 20:312–329.  https://doi.org/10.1080/10910344.2016.1168930 CrossRefGoogle Scholar
  9. 9.
    Tao G, Zhang J, Shen X, Bai L, Ma C, Wang J (2016) Feasibility study on ultrasonic vibration assisted milling for squamous surface. Procedia CIRP 42:847–852.  https://doi.org/10.1016/j.procir.2016.03.006 CrossRefGoogle Scholar
  10. 10.
    Mehbudi P, Baghlani V, Akbari J, Bushroa AR, Mardi NA (2013) Applying ultrasonic vibration to decrease drilling-induced delamination in GFRP laminates. Procedia CIRP 6:577–582.  https://doi.org/10.1016/j.procir.2013.03.097 CrossRefGoogle Scholar
  11. 11.
    Sharma V, Pandey PM (2016) Recent advances in ultrasonic assisted turning: a step towards sustainability. Cogent Eng 3.  https://doi.org/10.1080/23311916.2016.1222776
  12. 12.
    Tabatabaei SMK, Behbahani S, Mirian SM (2013) Analysis of ultrasonic assisted machining (UAM) on regenerative chatter in turning. J Mater Process Technol 213:418–425.  https://doi.org/10.1016/j.jmatprotec.2012.09.018 CrossRefGoogle Scholar
  13. 13.
    Zou P, Xu Y, He Y et al (2015) Experimental investigation of ultrasonic vibration assisted turning of 304 austenitic stainless steel. Shock Vib 2015:1–19.  https://doi.org/10.1155/2015/817598 CrossRefGoogle Scholar
  14. 14.
    Haidong Z, Ping Z, Wenbin M, Zhongming Z (2016) A study on ultrasonic elliptical vibration cutting of Inconel 718. Shock Vib 2016:1–11.  https://doi.org/10.1155/2016/3638574 CrossRefGoogle Scholar
  15. 15.
    Dong G, Zhang H, Zhou M, Zhang Y (2012) Experimental investigation on ultrasonic vibration assisted turning of Sicp/Al composites. Mater Manuf Process 120813105547003 .  https://doi.org/10.1080/10426914.2012.709338
  16. 16.
    Sharma V, Pandey PM (2016) Optimization of machining and vibration parameters for residual stresses minimization in ultrasonic assisted turning of 4340 hardened steel. Ultrasonics 70:172–182.  https://doi.org/10.1016/j.ultras.2016.05.001 CrossRefGoogle Scholar
  17. 17.
    Zhong ZW, Lin G (2005) Diamond turning of a metal matrix composite with ultrasonic vibrations. Mater Manuf Process 20:727–735.  https://doi.org/10.1081/AMP-200055124 CrossRefGoogle Scholar
  18. 18.
    Guo P, Ehmann KF (2013) Development of a tertiary motion generator for elliptical vibration texturing. Precis Eng 37:364–371.  https://doi.org/10.1016/j.precisioneng.2012.10.005 CrossRefGoogle Scholar
  19. 19.
    Nath C, Rahman M (2008) Effect of machining parameters in ultrasonic vibration cutting. Int J Mach Tools Manuf 48:965–974.  https://doi.org/10.1016/j.ijmachtools.2008.01.013 CrossRefGoogle Scholar
  20. 20.
    Zhang X, Sui H, Zhang D, Jiang X (2018) Study on the separation effect of high-speed ultrasonic vibration cutting. Ultrasonics 87:166–181.  https://doi.org/10.1016/j.ultras.2018.02.016 CrossRefGoogle Scholar
  21. 21.
    Vivekananda K, Arka GN, Sahoo SK (2014) Design and analysis of ultrasonic vibratory tool (UVT) using FEM, and experimental study on ultrasonic vibration-assisted turning (UAT). Procedia Eng 97:1178–1186.  https://doi.org/10.1016/j.proeng.2014.12.396 CrossRefGoogle Scholar
  22. 22.
    Teimouri R, Amini S, Mohagheghian N (2017) Experimental study and empirical analysis on effect of ultrasonic vibration during rotary turning of aluminum 7075 aerospace alloy. J Manuf Process 26:1–12.  https://doi.org/10.1016/j.jmapro.2016.11.011 CrossRefGoogle Scholar
  23. 23.
    Farahnakian M, Razfar MR, Biglari FR (2015) Multi-constrained optimization in ultrasonic-assisted turning of hardened steel by electromagnetism-like algorithm. Proc Inst Mech Eng Part B J Eng Manuf 229:1933–1944.  https://doi.org/10.1177/0954405414542489 CrossRefGoogle Scholar
  24. 24.
    Zhou M, Hu L (2015) Development of an innovative device for ultrasonic elliptical vibration cutting. Ultrasonics 60:76–81.  https://doi.org/10.1016/j.ultras.2015.02.015 CrossRefGoogle Scholar
  25. 25.
    (2018) COMSOL Multiphysics. https://www.comsol.com/
  26. 26.
    Understanding Cemented Carbide (2005). SANDVIK hard materials, Stockholm, SwedenGoogle Scholar
  27. 27.
    Automation Creations, Inc. MatWeb. In: a4. http://www.matweb.com/. Accessed 26 Aug 2017
  28. 28.
    Coromant S Turning Tool catalog (2012). SANDVIK Coromant, Stockholm, SwedenGoogle Scholar
  29. 29.
    Ratnam MM (2017) 1.1 factors affecting surface roughness in finish turning. In: Comprehensive materials finishing. Elsevier, pp 1–25Google Scholar
  30. 30.
    Siddhpura M, Paurobally R (2012) A review of chatter vibration research in turning. Int J Mach Tools Manuf 61:27–47.  https://doi.org/10.1016/j.ijmachtools.2012.05.007 CrossRefGoogle Scholar
  31. 31.
    Altintas Y (2012) Manufacturing automation: metal cutting mechanics, machine tool vibrations, and CNC design, 2nd edn. Cambridge University PressGoogle Scholar
  32. 32.
    Astašev VK, Babitsky VI, Khusnutdinova K (2007) Ultrasonic processes and machines: dynamics, control and applications, 1st edn. Springer, BerlinGoogle Scholar
  33. 33.
    Miodrag P (2002) Multifrequency ultrasonic structural actuators. Google PatentsGoogle Scholar
  34. 34.
    Zhang L (1999) On the separation criteria in the simulation of orthogonal metal cutting using the finite element method. J Mater Process Technol 89–90:273–278.  https://doi.org/10.1016/S0924-0136(99)00023-0 CrossRefGoogle Scholar
  35. 35.
    Silberschmidt VV, Mahdy SMA, Gouda MA, Naseer A, Maurotto A, Roy A (2014) Surface-roughness improvement in ultrasonically assisted turning. Procedia CIRP 13:49–54.  https://doi.org/10.1016/j.procir.2014.04.009 CrossRefGoogle Scholar
  36. 36.
    Ahmed N, Mitrofanov AV, Babitsky VI, Silberschmidt VV (2007) Analysis of forces in ultrasonically assisted turning. J Sound Vib 308:845–854.  https://doi.org/10.1016/j.jsv.2007.04.003 CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  1. 1.Centre for Micro-Electro Mechanical Systems, Department of Mechanical EngineeringUniversity of MinhoGuimarãesPortugal
  2. 2.CICECO, Department of Materials & Ceramic EngineeringUniversity of AveiroAveiroPortugal

Personalised recommendations