Advertisement

Effect of environmental temperature on dynamic behavior of an adjustable preload double-nut ball screw

  • De-Shin LiuEmail author
  • Pen-Chen Lin
  • Jheng-Jie Lin
  • Chuen-Ren Wang
  • Ting-Nung Shiau
Open Access
ORIGINAL ARTICLE
  • 108 Downloads

Abstract

The dynamic behavior of adjustable preload double-nut ball screw has been investigated by finite element simulation model under different environmental temperature conditions. The simulations focus specifically on the effects of the ambient temperature (5~55 °C) on the torque acting on the flange of the ball screw mechanism at rotational speeds of 50~1000 rpm. The environment temperature effect was less studies to discuss the heat deformation issue of ball screw. The validity of the simulation results is confirmed by comparing the predicted torque values with the experimental measurements. It is shown that the torque decreases logarithmically with an increasing temperature due to a change in the expansion coefficients of the ball screw mechanism components and a reduction in the viscosity of the ball screw lubricant. In particular, for a rotational speed of 1000 rpm, the torque reduces by approximately 75.6% as the environmental temperature is increased from 5 to 55 °C. However, for a constant temperature, the torque decreases with an increasing rotational speed due to centrifugal effects. For a low-rotational speed of 100 rpm, a good qualitative agreement is observed between the simulated torque and the measured torque at higher temperatures. However, in the low-temperature regime (e.g., 5 °C), the simulated torque is around 47.6% lower than the measured value.

Keywords

Environmental temperature Adjustable preload double-nut ball screw 

Notes

Acknowledgements

The authors thank the AIM-HI of National Chung Cheng University and HIWIN© Technologies Corporation of Taiwan for their help in this study.

References

  1. 1.
    Olaru D, Puiu GC, Balan LC, Puiu V (2004) A new model to estimate friction torque in a ball screw system. Prod Eng 333–346Google Scholar
  2. 2.
    Sobolewski JZ (2012) Vibration of the ball screw drive. J Eng Fail Anal 24:1–8CrossRefGoogle Scholar
  3. 3.
    Mu SG, Feng XY (2011) Study of the dynamic characteristic of high-speed screw. J Hunan Univ 38:25–29Google Scholar
  4. 4.
    Chen JS, Huang YK, Cheng CC (2004) Mechanical model and contouring analysis of high-speed ball-screw drive systems with compliance effect. J Adv Manuf Technol 24:241–250Google Scholar
  5. 5.
    Weule H, Frank T (1999) Advantage and characteristics of a dynamic feeds axis with ball screw drive and driven nut. J Ann CIRP 48:303–306CrossRefGoogle Scholar
  6. 6.
    Verl A, Frey S (2010) Correlation between feed velocity and preloading in ball screw drives. J CIRP Ann Manuf Technol 59:429–433CrossRefGoogle Scholar
  7. 7.
    Verl A, Frey S, Heinze T (2014) Double-nut ball screw with improved operating characteristics. J CIRP Ann Manuf Technol 63:361–364CrossRefGoogle Scholar
  8. 8.
    Wei CC, Lin JF, Horng JH (2009) Analysis of a ball screw with a preload and lubrication. J Tribol Int 42:1816–1831CrossRefGoogle Scholar
  9. 9.
    Reynolds O (1876) On rolling-friction. Philos Trans R Soc Lond 166:155–174CrossRefGoogle Scholar
  10. 10.
    Harris T (1971) Ball motion in thrust-loaded, angular-contact ball bearings with coulomb friction. ASME Trans J Lubr Technol 93:32–38CrossRefGoogle Scholar
  11. 11.
    Hamrock BJ (1994) Fundamentals of fluid film lubrication. McGraw-Hill, New YorkGoogle Scholar
  12. 12.
    Verl A, Frey S (2010) Correlation between feed velocity and preloading in ball screw drives. CIRP Ann Manuf Technol 59:429–432CrossRefGoogle Scholar
  13. 13.
    Wang CR, Liu DS, Huang CH, Shiau TN (2016) Numerical investigation into dynamic behavior of adjustable preload double-nut ball screw. J Mech Sci Technol 30:4489–4496CrossRefGoogle Scholar
  14. 14.
    Xia JY, Hu YM, Wu B, Shi TL (2009) Research on thermal dynamics characteristics and modelling approach of ball screw. Int J Adv Manuf Technol 43:421–430CrossRefGoogle Scholar
  15. 15.
    Xu ZZ, Liu XJ, Kim HK, Shin JH, Lyu SK (2011) Thermal error forecast and performance evaluation for an air-cooling ball screw system. Int J Mach Tool Manu 51:605–611CrossRefGoogle Scholar
  16. 16.
    Brouwera MD, Guptab LA, Sadeghia F, Peroulisb D, Adamsa D (2012) High temperature dynamic viscosity sensor for engine oil. Sensors Actuators A Phys 173:102–107CrossRefGoogle Scholar
  17. 17.
    Technical Manual of Ball Screw of HIWIN (2018) 599TE21-1898 22-31.Google Scholar

Copyright information

© The Author(s) 2018

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Authors and Affiliations

  1. 1.Advanced Institute of Manufacturing with High-tech Innovations and Department of Mechanical EngineeringNational Chung Cheng UniversityTaiwanRepublic of China

Personalised recommendations