Advertisement

Modified short-run statistical process control for test and measurement process

  • Chin Kok Koh
  • Jeng Feng ChinEmail author
  • Shahrul Kamaruddin
ORIGINAL ARTICLE
  • 34 Downloads

Abstract

The key characteristics of test and measurement (T&M) manufacturing are short-run, multi-product families and testing at multi-stations. These characteristics render statistical process control (SPC) inefficacious because inherently meagre data do not warrant meaningful control limits. Measurement errors increase the risks of false acceptance and rejection, thereby leading to such consequences as unnecessary process adjustments and loss of confidence in SPC. This study presents a modified SPC model that incorporates measurement uncertainty from guard bands into the \( \overline{\mathrm{Z}} \) and W charts, thereby addressing the implications of short runs, multi-stations and measurement errors on SPC. The implementation of this model involves two phases. Phase I retrospective analysis computes the input parameters, such as the standard deviation of the measurement uncertainty, measurement target and estimate of the population standard deviation. Thereafter, five-band setting and sensitivity factor are proposed to estimate process standard deviation to maximise the opportunity to detect the assignable causes with low false-reject rate. Lastly, the \( \overline{\mathrm{Z}} \) and W charts are generated in Phase II using standardised observation technique that considers the measurement target and estimated process standard deviations. Run tests based on Nelson rules interpret the charts. Validation was performed in three case studies in an actual industry.

Keywords

Statistical process control Short run Standardised observation techniques Measurement error Measurement uncertainty 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgement

This work was supported by Research University Grant (RUI), Universiti Sains Malaysia [grant number 8014069].

References

  1. 1.
    Del Castillo E, Grayson JM, Montgomery DC, Runger GC (1996) A review of statistical process control for short run manufacturing systems. Commun Stat Theory Methods 25(11):2723–2737zbMATHGoogle Scholar
  2. 2.
    Chen G (1997) The mean and standard deviation of the run length distribution of X charts when control limits are estimated. Stat Sin 7:789–798zbMATHGoogle Scholar
  3. 3.
    Tsai TR, Lin JJ, Wu SJ, Lin HC (2005) On estimating control limits of X chart when the number of subgroups is small. Int J Adv Manuf Technol 26:1312–1316Google Scholar
  4. 4.
    Montgomery DC (2013) Statistical quality control: a modern introduction, 7th edn. Wiley, SingaporezbMATHGoogle Scholar
  5. 5.
    Costa AFB, Castagliola P (2011) Effect of measurement error and autocorrelation on the X̄ chart. J Appl Stat 38(4):611–673MathSciNetGoogle Scholar
  6. 6.
    Chakraborty A, Khurshid A (2013) Measurement error effect on the power of control chart for zero-truncated Poisson distribution. Int J Qual Res 7(3):3–14Google Scholar
  7. 7.
    Chandra MJ (2001) Statistical quality control. CRC Press LLC, FloridaGoogle Scholar
  8. 8.
    Kanazuka T (1986) The effects of measurement error on the power of X - R charts. J Qual Technol 18:91–95Google Scholar
  9. 9.
    Tricker A, Coates E, Okell E (1998) The effect on the R chart of precision of measurement. J Qual Technol 30(3):232–239Google Scholar
  10. 10.
    Khoo MBC, Moslim NH (2010) A study on Q chart for short runs production. Proceedings of the Regional Conference on Statistical Sciences (RCSS’10). June 2010, 1–8Google Scholar
  11. 11.
    Jin J, Shi J (1999) State space modeling of sheet metal assembly for dimensional control. J Manuf Sci Eng 121:756–762Google Scholar
  12. 12.
    Camelio J, Hu SJ, Ceglarek D (2003) Modeling variation propagation of multistation assembly systems with compliant parts. J Mech Des 125(4):673–681Google Scholar
  13. 13.
    Djurdjanovic D, Ni J (2006) Stream of variations (SoV)-based measurement scheme analysis in multistation machining system. IEEE Trans Autom Sci Eng 3(4):407–422Google Scholar
  14. 14.
    Zhang M, Djurdjanovic D, Ni J (2007) Diagnosibility and sensitivity analysis for multi-station machining processes. Int J Mach Tools Manuf 47(3–4):646–657Google Scholar
  15. 15.
    Abellan-Nebot JV, Liu J, Subiron FR (2011) Design of multi-station manufacturing processes by integrating the stream-of-variation model and shop-floor data. J Manuf Syst 30(2):70–82Google Scholar
  16. 16.
    Jiao Y, Djurdjanovic D (2011) Compensability of errors in product quality in multistage manufacturing processes. J Manuf Syst 30(4):204–213Google Scholar
  17. 17.
    Linna KW, Woodall WH (2001) Effect of measurement error on Shewhart control charts. J Qual Technol 33(2):213–222Google Scholar
  18. 18.
    ILAC-G8:03/2009 (2009) Guidelines on assessment and reporting of compliance with specification. International Laboratory Accreditation Cooperation. Retrieved from https://ilac.org/publications-and-resources/ilac-guidance-series
  19. 19.
    JCGM 100:2008 (2008) Evaluation of measurement data– guide to the expression of uncertainty in measurement (GUM 1995 with minor corrections). Joint Committee for Guides in Metrology. Retrieved from https://www.bipm.org/utils/common/documents/jcgm/JCGM_100_2008_E.pdf
  20. 20.
    Cheatle KR (2006) Fundamentals of test measurement instrumentation. ISA, North CarolinaGoogle Scholar
  21. 21.
    Nielsen HS (2017) Estimating measurement uncertainty. Metrology Consulting Inc. Web. https://www.hn-metrology.com/uncertaintytraining.htm. Accessed 6 October 2017
  22. 22.
    ISO/IEC 17025:2017 (2017) General requirements for the competence of testing and calibration laboratories (3rd Ed.). International Organization for Standardization/ International Electrotechnical Commission. Retrieved from https://www.iso.org/standard/66912.html
  23. 23.
    ANSI/NCSL Z540.3:2006 (2006) Requirements for the calibration of measuring and test equipment. American National Standard Institute/ National Conference of Standards Laboratories. Retrieved from http://www.ncsli.org/i/i/sp/z540/z540s/iMIS/Store/z540s.aspx
  24. 24.
    Castrup H (2007) Risk analysis methods for complying with Z540.3. Proceedings of the NCSLI International Workshop and Symposium, August 2007. St. Paul, MNGoogle Scholar
  25. 25.
    Sediva S, Havlikova M (2013) Comparison of GUM and Monte Carlo method for evaluation measurement uncertainty of indirect measurements. Proceedings of the 14th International Carpathian Control Conference (ICCC), 26–29 May 2013 Ryto 325–329Google Scholar
  26. 26.
    Deaver D (1995) Using guardbands to justify TURs less than 4:1. Proceedings of ASQC 49th Annual Quality Congress, 136–141Google Scholar
  27. 27.
    Mezouara H, Dlimi L, Salih A, Afechcar M (2015) Determination of the guard banding to ensure acceptable risk decision in the declaration of conformity. Int J Metrol Qual Eng 6:206Google Scholar
  28. 28.
    Pou JM, Leblond L (2015) Control of customer and supplier risks by the guardband method. Int J Metrol Qual Eng 6:205Google Scholar
  29. 29.
    Williams RH, Hawkins CF (1993) The effect of guardbands on error in production testing. In European Test Conference. Proceedings of ETC 93, Third, 19–22 April 1993. Rotterdam. 2–7Google Scholar
  30. 30.
    Hossain A, Choudhury ZA, Suyut S (1996) Statistical process control of an industrial process in real time. IEEE Trans Ind Appl 32(2):243–249Google Scholar
  31. 31.
    Koons GF, Luner JJ (1991) SPC in low-volume manufacturing: a case study. J Qual Technol 23(4):287–295Google Scholar
  32. 32.
    Quesenberry CP (1991) SPC Q charts for start-up processes and short or long runs. J Qual Technol 23(3):213–224Google Scholar
  33. 33.
    Celano G, Castagliola P, Trovato E, Fichera S (2011) Shewhart and EWMA t control charts for short production runs. Qual Reliab Eng Int 27:313–326Google Scholar
  34. 34.
    Teoh WL, Chuah SK, Khoo MBC, Castagliola P, Yeong WC (2017) Optimal designs of the synthetic t chart with estimated process mean. Comput Ind Eng 112:409–425Google Scholar
  35. 35.
    Gu K, Jia XZ, You HL, Zhang SH (2014) A t-chart for monitoring multi-variety and small batch production run. Qual Reliab Eng Int 30(2):287–299Google Scholar
  36. 36.
    Cullen JM (1987) The use of statistical process control in one-off and small batch production. Proceedings of 8th International Conference on Automated Inspection and Product Control, June 1987. Chicago 63–68Google Scholar
  37. 37.
    Bothe DR (1988) SPC for short production runs. Quality 27(12):58Google Scholar
  38. 38.
    Montgomery DC (1991) Introduction to statistical quality control, 2nd edn. Wiley, New YorkzbMATHGoogle Scholar
  39. 39.
    Moore SS, Murphy E (2013) Process visualization in medical device manufacture: an adaptation of short run SPC techniques. Qual Eng 25(3):247–265Google Scholar
  40. 40.
    Marques PA, Cardeira CB, Paranhos P, Ribeiro S, Gouveia H (2015) Selection of the most suitable statistical process control approach for short production runs: a decision-model. Int J Inform Educ Technol 5(4):303–310Google Scholar
  41. 41.
    Nelson LS (1989) Standardization of Shewhart control charts. J Qual Technol 21:287–289Google Scholar
  42. 42.
    Bothe DR (1989) A powerful new control chart for job shops. Proceedings of the 43rd Annual Quality Congress Transactions, May 1989. Toronto 265–270Google Scholar
  43. 43.
    Cullen CC, Bothe DR (1989) SPC for short production runs. Proceedings of the IEEE National Aerospace and Electronics Conference, 22–26 May 1989. Dyton, OH. 1960–1963Google Scholar
  44. 44.
    Wasserman GS (1994) Short run SPC using dynamic control chart. Comput Ind Eng 27(1–4):353–356Google Scholar
  45. 45.
    Wheeler DJ (1991) Short run SPC. SPC Press, Inc, KnoxvilleGoogle Scholar
  46. 46.
    Noskievičová D, Jarošová E (2013) Complex application of statistical process control in conditions of profile bars production. Proceedings of METAL2013, 15–17 May 2013. Brno, Czech RepublicGoogle Scholar
  47. 47.
    Zhou X, Govindaraju K, Jones G (2017) Monitoring fractional nonconformance for short-run production. Qual Eng.  https://doi.org/10.1080/08982112.2017.1360499
  48. 48.
    Farnum NR (1992) Control charts for short runs: nonconstant process and measurement error. J Qual Technol 24(2):138–144Google Scholar
  49. 49.
    Kirkup L, Frenkel B (2006) An introduction to uncertainty measurement. Cambridge University Press, New YorkzbMATHGoogle Scholar
  50. 50.
    Weckenmann A, Rinnagl M (2000) Acceptance of processes: do we need decision rules? Precis Eng 24:264–269Google Scholar
  51. 51.
    Quesenberry CP (1998) Statistical gymnastics. Qual Prog 31(9):78–79Google Scholar
  52. 52.
    UKAS (2007) The expression of uncertainty and confidence in measurement. M3003, 2nd edn. United Kingdom Accreditation Service, Staines-upon-ThamesGoogle Scholar
  53. 53.
    Taylor BN, Kuyatt CE (1994) Guidelines for evaluating and expressing the uncertainty of NIST measurement results. National Institute of Standards and Technology, MarylandGoogle Scholar
  54. 54.
    Bell S (2001) Measurement good practice guide no 11 (issue 2): a beginner’s guide to uncertainty of measurement. National Physical Laboratory, MiddlesexGoogle Scholar
  55. 55.
    Instone I (1996) Simplified method for assessing uncertainties in a commercial production environment. Teste and measurement. Proceeding of Metrology Forum, 10 Oct. London. 1–7Google Scholar
  56. 56.
    Dobbert M (2008) A guard-band strategy for managing false-accept risk. NCSLI Measure J Meas Sci 3(4):44–48Google Scholar
  57. 57.
    Hoaglin DC, Mosteller F, Tukey JW (1983) Understanding robust and exploratory data analysis. Wiley, New YorkzbMATHGoogle Scholar
  58. 58.
    Nelson LS (1984) The Shewhart control chart-tests for special causes. J Qual Technol 16(4):237–239Google Scholar
  59. 59.
    Noskievičová D (2013) Complex control chart interpretation. Int J Eng Bus Manag 5(13):1–7Google Scholar
  60. 60.
    Shapiro SS, Wilk MB (1965) An analysis of variance test for normality. Biometrika 52(3–4):591–611MathSciNetzbMATHGoogle Scholar
  61. 61.
    Scrucca L, Snow G, Bloomfield P (2017) Package ‘qcc’ (Version 2.7) [Source code]. https://cran.r-project.org/web/packages/qcc
  62. 62.
    Venables WN, Smith DM, the R Core Team (2017) An introduction to R. version 3.4.3. Retrieved from https://cran.r-project.org/doc/manuals/r-release/R-intro.pdf

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Chin Kok Koh
    • 1
  • Jeng Feng Chin
    • 1
    Email author
  • Shahrul Kamaruddin
    • 2
  1. 1.School of Mechanical Engineering, Engineering CampusUniversiti Sains MalaysiaNibong TebalMalaysia
  2. 2.Department of Mechanical EngineeringUniversiti Teknologi PetronasSeri IskandarMalaysia

Personalised recommendations