Numerical prediction and experimental analysis of the residual stress fields and generated distortion in hybrid laser/arc welded thick plates of high-strength steels
- 142 Downloads
Heating and cooling cycles that occur during the fusion joining process generate a significant amount of thermally caused residual stress that negatively influence the integrity and dimensional accuracy of the welded structures. The level of residual stress around the welding region was as large as the yield stress of the weld and was believed to have created an unwanted permanent deformation. In this paper, a three-dimensional thermo-metallurgical-mechanical finite element method (FEM), using the computational modeling software SYSWELD, was introduced to numerically study the residual stress fields and the distortion of thick welded plates of high-strength quenched and tempered steel (HSQTS) that were caused by hybrid laser/arc welding process in butt-joint configuration. The precision of thermal analysis results was verified prior to conducting mechanical analysis. The verified cooling curves obtained from the thermal simulation were acquired to predict the microstructure of the welding region. Employing the X-ray diffraction method (XRD), the field of residual stress was measured in order to validate the accuracy of the mechanical analysis. The results showed the numerically predicted temperature contours to be in a good agreement with the weld cross section as well as the temperature histories recorded by thermocouples. The microstructural evolution of the welding region revealed a relatively good consistency with the predicted phases based on the continuous cooling transformation (CCT) diagram and the numerically simulated cooling curves. It was shown that experimental and numerical results of the residual stress field and distortion matched well with a large distortion theory.
KeywordsHybrid laser/arc welding Thermo-metallurgical-mechanical analysis Residual stress SYSWELD
Unable to display preview. Download preview PDF.
The authors would like to express their gratitude to Andrew Socha for his help to prepare and run the setup for welding at the Research Center for Advanced Manufacturing at SMU. This work was partially funded by NSF Grant IIP-1539853.
- 1.Huang T ,Conrardy C, Dong P, Kvidahl L, Decan L, Distortion mitigation technique for lightweight ship structures fabrication, Northrop Grumman ship systems, Society of Naval Architects and Marine Engineers, USGoogle Scholar
- 3.Hassel T, Konya R, Collmann M, Schaumann P, Priebe S, Deiber TA, Beniyash A, Murray N, Bach FW (2013) Economical joining of tubular steel towers for wind turbines employing non-vacuum electron beam welding for high-strength steels in comparison with submerged arc welding. Weld World 57:551–559CrossRefGoogle Scholar
- 8.MazarAtabaki M, Yazdian N, Ma J, Kovacevic R (2016) High power laser welding of thick steel plates in a horizontal butt joint configuration. Opt Laser Technol 83:1–12Google Scholar
- 10.Rittichai Phaoniam, Kenji Shinozaki, Motomichi Yamamoto, Kota Kadoi, Akito Nishijima, Masayuki Yamamoto, (2014) Solidification cracking susceptibility of modified 9Cr1Mo steel weld metal during hot-wire laser welding with a narrow gap groove, weld world, Vol58:469–476Google Scholar
- 15.Radaj, D. (2003) Welding residual stresses and distortion: calculation and measurement, 2nd edn, Verlag für Schweissen und Verwandte Verfahren, DVS-Verlag 118–200Google Scholar
- 16.Lima TR, Tavares SMO, de Castro PMST (2017) Residual stress field and distortions resulting from welding processes: numerical modelling using SYSWELD. Ciênc Tecnol Mater 29:56–61Google Scholar
- 17.Derakhshan ED, Yazdian N, Craft B, Smith S, Kovacevic R (2018) Numerical simulation and experimental validation of residual stress and welding distortion induced by laser-based welding processes of thin structural steel plates in butt joint configuration. Opt Laser Technol 104:170–182CrossRefGoogle Scholar
- 18.M. Mazar Atabaki, N. Yazdian, R. Kovacevic, Hybrid laser/arc welding of thick high-strength steel in different configurations, Advances in Manufacturing, In Press
- 19.Kannatey-Asibu E (2009) Residual stresses and distortion, Princ. Laser mater. Process. John Wiley & Sons, Inc., New Jersey, pp 361–405Google Scholar
- 20.SYSWELD Reference manual version 2015. ESI GroupGoogle Scholar
- 24.Igor Barenyi, Ondrej Hires, Peter Liptak, (2013) Changes in mechanical properties of Armoured UHSLA steel ARMOX 500 after over tempering, problems of mechanics of mechatronics armament, aviation, safety engineering, 14:7–14Google Scholar
- 27.Ilman MN, Kusmono, Muslih MR, Subeki N, Wibowo H (2016) Mitigating distortion and residual stress by static thermal tensioning to improve fatigue crack growth performance of MIG AA5083 welds. Journal of Materials and Design 99:273–283Google Scholar