Advertisement

Tool runout and single-edge cutting in micro-milling

  • Xiang ZhangEmail author
  • Xudong Pan
  • Guanglin Wang
  • Dong Zhou
ORIGINAL ARTICLE

Abstract

Micro-milling is a direct and effective manufacturing method for complex three-dimensional miniaturized parts. Since tool runout has a great influence on micro-milling, this paper proposes a simple and effective method for measuring tool runout parameters. The method was based on the displacement measurement, which obtained the tool runout length and tool runout angle by solving some equations related to the cutter parameters. After analyzing the cutting trajectories of the cutter, a single-edge cutting criterion in micro-milling was proposed. According to the single-edge cutting criterion, the influencing factors of single-edge cutting both in micro-side milling and micro-end milling were analyzed respectively. Finally, the influences of single-edge cutting on micro-milling were analyzed and the single-edge cutting phenomenon was verified by the experiment of cutting forces.

Keywords

Tool runout Single edge cutting Micro-milling Criterion 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding information

This work is supported by the National Natural Science Foundation of China (NSFC, No.51605118) and the Fundamental Research Funds for the Central Universities (Grant No. HIT.NSRIF. 2016042).

References

  1. 1.
    Liu Y, Li PF, Liu K, Zhang YM (2017) Micro milling of copper thin wall structure. Int J Adv Manuf Technol 90(1–4):405–412CrossRefGoogle Scholar
  2. 2.
    Yang SC, Liu WW, Zhang YH, Wan Q (2017) Experimental evaluation on micro-texture parameters of carbide ball-nosed end mill in machining of titanium alloy. Int J Adv Manuf Technol 26:1–11 (Published online)Google Scholar
  3. 3.
    Li CF, Lai XM, Li HT, Ni J (2007) Modeling of three-dimensional cutting forces in micro-end-milling. J Micromech Microeng 17(4):671–678CrossRefGoogle Scholar
  4. 4.
    Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part II: Tool run-out. Int J Mach Tools Manuf 40(15):2175–2192CrossRefGoogle Scholar
  5. 5.
    Han ZY, Zhang X, Sun YZ, Fu HY, Liang YC (2011) Single edge cutting phenomenon and instantaneous uncut chip thickness model of micro-ball-end milling. Adv Sci Lett 4(4–5):1387–1393CrossRefGoogle Scholar
  6. 6.
    Tai CC, Fuh KH (1994) A predictive force model in ball-end milling including eccentricity effects. Int J Mach Tools Manuf 34(7):959–979CrossRefGoogle Scholar
  7. 7.
    Feng HY, Menq CH (1994) The prediction of cutting forces in the ball-end milling process—I. Model formulation and model building procedure. Int J Mach Tools Manuf 34(5):697–710CrossRefGoogle Scholar
  8. 8.
    Nakkiew W, Lin CW, Tu JF (2006) A new method to quantify radial error of a motorized end-milling cutter/spindle system at very high speed rotations. Int J Mach Tools Manuf 46(7):877–889CrossRefGoogle Scholar
  9. 9.
    Hekman KA, Liang SY (1997) In-process monitoring of end milling cutter runout. Mechatronics 7(1):1–10CrossRefGoogle Scholar
  10. 10.
    Wan M, Zhang WH, Dang JW, Yang Y (2009) New procedures for calibration of instantaneous cutting force coefficients and cutter runout parameters in peripheral milling. Int J Mach Tools Manuf 49(14):1144–1151CrossRefGoogle Scholar
  11. 11.
    Wang JJJ, Zheng CM (2003) Identification of cutter offset in end milling without a prior knowledge of cutting coefficients. Int J Mach Tools Manuf 43(7):687–697CrossRefGoogle Scholar
  12. 12.
    Ko JH, Yun WS, Cho DW, Ehmann KF (2002) Development of a virtual machining system, part 1: approximation of the size effect for cutting force prediction. Int J Mach Tools Manuf 42(15):1595–1605CrossRefGoogle Scholar
  13. 13.
    Jing XB, Tian YL, Yuan YJ, Wang FJ (2017) A runout measuring method using modeling and simulation cutting force in micro end-milling. Int J Adv Manuf Technol 90(1–4):405–412Google Scholar
  14. 14.
    Zhang X, Han ZY, Fu HY, Sun YZ, Liang YC (2011) Identification of spindle runout parameters in micro-ball-end milling. Adv Sci Lett 4(4–5):1776–1781CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Xiang Zhang
    • 1
    Email author
  • Xudong Pan
    • 1
  • Guanglin Wang
    • 1
  • Dong Zhou
    • 1
  1. 1.School of Mechatronics EngineeringHarbin Institute of TechnologyHarbinChina

Personalised recommendations