Ultrasonic assisted grinding of advanced materials for biomedical and aerospace applications—a review

ORIGINAL ARTICLE
First Online:
Received:
Accepted:

Abstract

This paper presents a review on ultrasonic-assisted grinding (UAG) of advanced materials, specifically investigating the effects of ultrasonication on material removal rates (MRR), grinding forces and energy, tool wears, wheel loading, residual stress and surface/subsurface damages. It compares the performance of UAG of ceramics and super alloys for biomedical and aerospace applications, with the performance of the conventional grinding (CG) techniques. The effects of the UAG process parameters on the MRR, grinding ratio, tool life, residual stresses and surface/subsurface damages were also investigated. Studies on the performance of the UAG process in the machining of brittle and ductile materials have shown that the introduction of the ultrasonic system to the grinding process helps to increase the material removal rates significantly, and consequently reduces the surface roughness, grinding forces and subsurface damages. The self-sharpening phenomenon found in the UAG process was realised to be responsible for the improved machining performance of the UAG process. Furthermore, the application of biodegradable lubricants (vegetable oil based) to the grinding process was also found to improve the machining performances of the UAG process, achieving almost the same performance as the non-biodegradable lubricants. As such, the use of the biodegradable lubricants in the grinding process was encouraged due to its economic benefits, and environmental friendliness.

Keywords

Ultrasonic assisted grinding (UAG) Ceramic Super-alloys Biomedical and aerospace applications 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Agarwal S, Rao PV (2005) A new surface roughness prediction model for ceramic grinding. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 219 (11):811–819Google Scholar
  2. 2.
    Agarwal S, Rao PV (2008) Experimental investigation of surface/subsurface damage formation and material removal mechanisms in SiC grinding. Int J Mach Tools Manuf 48(6):698–710CrossRefGoogle Scholar
  3. 3.
    Thoe T, Aspinwall D, Wise M (1998) Review on ultrasonic machining. Int J Mach Tools Manuf 38(4):239–255CrossRefGoogle Scholar
  4. 4.
    Samant AN, Dahotre NB (2009) Laser machining of structural ceramics—a review. J Eur Ceram Soc 29(6):969–993CrossRefGoogle Scholar
  5. 5.
    Uhlmann E, Sammler C (2010) Influence of coolant conditions in ultrasonic assisted grinding of high performance ceramics. Prod Eng 4(6):581–587CrossRefGoogle Scholar
  6. 6.
    Wang H, Wang CA, Yao X, Fang D (2007) Processing and mechanical properties of zirconium Diboride-based ceramics prepared by spark plasma sintering. J Am Ceram Soc 90(7):1992–1997CrossRefGoogle Scholar
  7. 7.
    Arunachalam R, Mannan M, Spowage A (2004) Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools. Int J Mach Tools Manuf 44(9):879–887CrossRefGoogle Scholar
  8. 8.
    Qu W, Wang K, Miller M, Huang Y, Chandra A (2000) Using vibration-assisted grinding to reduce subsurface damage. Precis Eng 24(4):329–337CrossRefGoogle Scholar
  9. 9.
    Denkena B, de Leon L, Hahmann D (2008) Ultrasonic assisted grinding of brittle materials–surface topography and process forces. In: Proceedings of the 23rd Annual Meeting of the ASPE and the Twelfth ICPE, ASPE/ICPE. pp 384–387Google Scholar
  10. 10.
    Zemzemi F, Rech J, Salem WB, Dogui A, Kapsa P (2014) Identification of friction and heat partition model at the tool-chip-workpiece interfaces in dry cutting of an Inconel 718 alloy with CBN and coated carbide tools. Advances in Manufacturing Science and Technology 38 (1)Google Scholar
  11. 11.
    Huang H, Liu Y (2003) Experimental investigations of machining characteristics and removal mechanisms of advanced ceramics in high speed deep grinding. Int J Mach Tools Manuf 43(8):811–823CrossRefGoogle Scholar
  12. 12.
    Xue J, An L, Sun Q (2013) Grinding technology for engineering ceramics—a review. In: Advanced materials research. Trans Tech Publ, pp 31–36Google Scholar
  13. 13.
    Malkin S (1989) Grinding technology: theory and applications of machining with AbrasivesEllis Horwood Limited. Chichester, EnglandGoogle Scholar
  14. 14.
    Cao J, Wu Y, Lu D, Fujimoto M, Nomura M (2014) Material removal behavior in ultrasonic-assisted scratching of SiC ceramics with a single diamond tool. Int J Mach Tools Manuf 79:49–61CrossRefGoogle Scholar
  15. 15.
    Zhong Z, Yang H (2004) Development of a vibration device for grinding with microvibration. Mater Manuf Process 19(6):1121–1132CrossRefGoogle Scholar
  16. 16.
    Tesfay HD, Xu Z, Li Z (2016) Ultrasonic vibration assisted grinding of bio-ceramic materials: an experimental study on edge chippings with Hertzian indentation tests. The International Journal of Advanced Manufacturing Technology:1–12Google Scholar
  17. 17.
    Chen J, Fang Q, Li P (2015) Effect of grinding wheel spindle vibration on surface roughness and subsurface damage in brittle material grinding. Int J Mach Tools Manuf 91:12–23CrossRefGoogle Scholar
  18. 18.
    Pei Z, Ferreira P, Haselkorn M (1995) Plastic flow in rotary ultrasonic machining of ceramics. J Mater Process Technol 48(1):771–777CrossRefGoogle Scholar
  19. 19.
    Xiao X, Zheng K, Liao W (2014) Theoretical model for cutting force in rotary ultrasonic milling of dental zirconia ceramics. Int J Adv Manuf Technol 75(9–12):1263–1277CrossRefGoogle Scholar
  20. 20.
    Zeng W, Li Z, Pei Z, Treadwell C (2005) Experimental observation of tool wear in rotary ultrasonic machining of advanced ceramics. Int J Mach Tools Manuf 45(12):1468–1473CrossRefGoogle Scholar
  21. 21.
    Ahmed Y, Cong W, Stanco MR, Xu Z, Pei Z, Treadwell C, Zhu Y, Li Z (2012) Rotary ultrasonic machining of alumina dental ceramics: a preliminary experimental study on surface and subsurface damages. J Manuf Sci Eng 134(6):064501CrossRefGoogle Scholar
  22. 22.
    Choi J, Jeon B, Kim B (2007) Chemical-assisted ultrasonic machining of glass. J Mater Process Technol 191(1):153–156CrossRefGoogle Scholar
  23. 23.
    Kirchner HP (1984) Damage penetration at elongated machining grooves in hot-pressed Si3N4. J Am Ceram Soc 67(2):127–132CrossRefGoogle Scholar
  24. 24.
    Zhang B, Howes TD (1994) Material-removal mechanisms in grinding ceramics. CIRP AnnManuf Technol 43(1):305–308CrossRefGoogle Scholar
  25. 25.
    Xu HH, Jahanmir S (1995) Microfracture and material removal in scratching of alumina. J Mater Sci 30(9):2235–2247CrossRefGoogle Scholar
  26. 26.
    Xin-honga Y, Jie-caib H, Yu-minb Z, Hong-bob Z, Xue-junb Z (2006) Research on ultrasonic vibration grinding of the hard and brittle materials. Chin J Aeronaut 19:S9–S13Google Scholar
  27. 27.
    Yanyan Y, Bo Z, Junli L (2009) Ultraprecision surface finishing of nano-ZrO2 ceramics using two-dimensional ultrasonic assisted grinding. Int J Adv Manuf Technol 43(5–6):462–467CrossRefGoogle Scholar
  28. 28.
    Moriwaki T, Shamoto E (1995) Ultrasonic elliptical vibration cutting. CIRP Ann Manuf Technol 44(1):31–34CrossRefGoogle Scholar
  29. 29.
    Akbari J, Borzoie H, Mamduhi MH (2008) Study on ultrasonic vibration effects on grinding process of alumina ceramic (Al2O3). World Acad Sci Eng Technol 41:785–789Google Scholar
  30. 30.
    Gong H, Fang F, Hu X (2010) Kinematic view of tool life in rotary ultrasonic side milling of hard and brittle materials. Int J Mach Tools Manuf 50(3):303–307CrossRefGoogle Scholar
  31. 31.
    Vicario I, Gonzalo O, Bengoetxea I (2007) Rotary ultrasonic machining of aluminium oxide ceramics: designed experiments. Int J Mach Mach Mater 2(2):233–243Google Scholar
  32. 32.
    Brecher C, Schug R, Weber A, Wenzel C, Hannig S (2010) New systematic and time-saving procedure to design cup grinding wheels for the application of ultrasonic-assisted grinding. Int J Adv Manuf Technol 47(1–4):153–159CrossRefGoogle Scholar
  33. 33.
    Suzuki K, Uematsu T, Iwai M, Ninomiya S, Sano S, Nakagawa T A (2007) New complex grinding method for ceramic materials combined with ultrasonic vibration and electrodischarge machining. In: Key engineering materials. Trans Tech Publ, pp 439–444Google Scholar
  34. 34.
    Gao G, Zhao B, Xiang D, Kong Q (2009) Research on the surface characteristics in ultrasonic grinding nano-zirconia ceramics. J Mater Process Technol 209(1):32–37CrossRefGoogle Scholar
  35. 35.
    Uhlmann E Hübert C (2007) Ultrasonic assisted grinding of advanced ceramics. In: Proceedings of the ASPE spring topical meetingGoogle Scholar
  36. 36.
    Pei Z (1995) Rotary ultrasonic machining of ceramics: characterization and extensions. University of Illinois at Urbana-ChampaignGoogle Scholar
  37. 37.
    Marinescu ID, Hitchiner MP, Uhlmann E, Rowe WB, Inasaki I (2006) Handbook of machining with grinding wheels. CRC PressGoogle Scholar
  38. 38.
    Feucht F, Ketelaer J, Wolff A, Mori M, Fujishima M (2014) Latest machining technologies of hard-to-cut materials by ultrasonic machine tool. Procedia CIRP 14:148–152CrossRefGoogle Scholar
  39. 39.
    Brehl D, Dow T (2008) Review of vibration-assisted machining. Precis Eng 32(3):153–172CrossRefGoogle Scholar
  40. 40.
    Ma CX, Shamoto E, Moriwaki T (2005) Drilling assisted by ultrasonic elliptical vibration. In: Key engineering materials. Trans Tech Publ, pp 443–446Google Scholar
  41. 41.
    Lv D, Huang Y, Tang Y, Wang H (2013) Relationship between subsurface damage and surface roughness of glass BK7 in rotary ultrasonic machining and conventional grinding processes. Int J Adv Manuf Technol 67(1–4):613–622CrossRefGoogle Scholar
  42. 42.
    Lauwers B (2011) Surface integrity in hybrid machining processes. Procedia Eng 19:241–251CrossRefGoogle Scholar
  43. 43.
    Lauwers B, Bleicher F, Ten Haaf P, Vanparys M, Bernreiter J, Jacobs T, Loenders J (2010) Investigation of the process-material interaction in ultrasonic assisted grinding of ZrO2 based ceramic materials. In: Proceedings of the 4th CIRP International Conference on High Performance CuttingGoogle Scholar
  44. 44.
    Jianhua Z, Yan Z, Shuo Z, Fuqiang T, Lanshen G, Ruizhen D (2014) Study on effect of ultrasonic vibration on grinding force and surface quality in ultrasonic assisted micro end grinding of silica glass. Shock and Vibration 2014Google Scholar
  45. 45.
    Kalpakjian S, Schmid S (2014) Manufacturing processes for engineering materials–5th Edition. agenda 12:1Google Scholar
  46. 46.
    Winter M, Ibbotson S, Kara S, Herrmann C (2015) Life cycle assessment of cubic boron nitride grinding wheels. J Clean Prod 107:707–721CrossRefGoogle Scholar
  47. 47.
    El-Meliegy E, van Noort R (2011) Glasses and glass ceramics for medical applications. Springer science & business mediaGoogle Scholar
  48. 48.
    Shi D (2006) Introduction to biomaterials. 清华大学出版社有限公司Google Scholar
  49. 49.
    Cotton JD, Clark LP, Phelps HR (2002) Titanium alloys on the F-22 fighter airframe. Adv Mater Process 160(5):25–28Google Scholar
  50. 50.
    Williams JC, Starke EA (2003) Progress in structural materials for aerospace systems. Acta Mater 51(19):5775–5799CrossRefGoogle Scholar
  51. 51.
    Buhl H (2012) Advanced aerospace materials. Springer Science & Business MediaGoogle Scholar
  52. 52.
    Niinomi M (2002) Recent metallic materials for biomedical applications. Metall Mater Trans A 33(3):477. doi:10.1007/s11661-002-0109-2 CrossRefGoogle Scholar
  53. 53.
    Speidel MO, Uggowitzer PJ (1992) High manganese, high nitrogen austenitic stainless steels: their strength and toughnessGoogle Scholar
  54. 54.
    Campbell Jr FC (2011) Manufacturing technology for aerospace structural materials. ElsevierGoogle Scholar
  55. 55.
    Gates R, Wang Y, Ying T-N, Hsu S (1999) A grinding map concept for optimization of ceramic machining. Tribol Trans 42(4):715–722CrossRefGoogle Scholar
  56. 56.
    Lauwers B, Klocke F, Klink A, Tekkaya AE, Neugebauer R, Mcintosh D (2014) Hybrid processes in manufacturing. CIRP Ann Manuf Technol 63(2):561–583CrossRefGoogle Scholar
  57. 57.
    Isaev A, Anokhin V (1961) Ultrasonic vibration of a metal cutting tool. Vest Mashinos (in Russian)Google Scholar
  58. 58.
    Moriwaki T, Shamoto E, Inoue K (1992) Ultraprecision ductile cutting of glass by applying ultrasonic vibration. CIRP Ann Manuf Technol 41(1):141–144CrossRefGoogle Scholar
  59. 59.
    Moriwaki T, Shamoto E (1991) Ultraprecision diamond turning of stainless steel by applying ultrasonic vibration. CIRP Ann Manuf Technol 40(1):559–562CrossRefGoogle Scholar
  60. 60.
    Brinksmeier E, Glabe R (1999) Elliptical vibration cutting of steel with diamond tools. In: Proc. of the 14th Annual ASPE Meeting, Monterey, California, USA. vol 05.11.Google Scholar
  61. 61.
    Shamoto E, Moriwaki T (1994) Study on elliptical vibration cutting. CIRP Ann Manuf Technol 43(1):35–38CrossRefGoogle Scholar
  62. 62.
    Ding K, Fu Y, Su H, Gong X, Wu K (2014) Wear of diamond grinding wheel in ultrasonic vibration-assisted grinding of silicon carbide. Int J Adv Manuf Technol 71(9–12):1929–1938CrossRefGoogle Scholar
  63. 63.
    Chen J, Fang Q, Wang C, Du J, Liu F (2016) Theoretical study on brittle–ductile transition behavior in elliptical ultrasonic assisted grinding of hard brittle materials. Precision EngineeringGoogle Scholar
  64. 64.
    Liang ZQ, Wang XB, Wu YB, Zhao WX (2010) Elliptical ultrasonic assisted grinding (EUAG) of monocrystal sapphire—surface formation characteristics. In: Advanced materials research. Trans Tech Publ, pp 367–372Google Scholar
  65. 65.
    Suzuki N, Nakamura A, Shamoto E, Harada K, Matsuo M, Osada M (2003) Ultraprecision micromachining of hardened steel by applying ultrasonic elliptical vibration cutting. In: Micromechatronics and Human Science, 2003. MHS 2003. Proceedings of 2003 International Symposium on. IEEE, pp 221–226Google Scholar
  66. 66.
    Li X, Zhang D (2006) Ultrasonic elliptical vibration transducer driven by single actuator and its application in precision cutting. J Mater Process Technol 180(1):91–95CrossRefGoogle Scholar
  67. 67.
    Li S, Wu Y, Nomura M (2016) Effect of grinding wheel ultrasonic vibration on chip formation in surface grinding of Inconel 718. The International Journal of Advanced Manufacturing Technology:1–13Google Scholar
  68. 68.
    Jian-Hua Z, Yan Z, Fu-Qiang T, Shuo Z, Lan-Shen G (2015) Kinematics and experimental study on ultrasonic vibration-assisted micro end grinding of silica glass. Int J Adv Manuf Technol 78(9–12):1893–1904CrossRefGoogle Scholar
  69. 69.
    Liu K, Li X, Rahman M (2008) Characteristics of ultrasonic vibration-assisted ductile mode cutting of tungsten carbide. Int J Adv Manuf Technol 35(7–8):833–841CrossRefGoogle Scholar
  70. 70.
    Tawakoli T, Azarhoushang B, Rabiey M (2009) Ultrasonic assisted dry grinding of 42CrMo4. Int J Adv Manuf Technol 42(9–10):883–891CrossRefGoogle Scholar
  71. 71.
    Saljé E, Möhlen H (1986) Fundamental dependencies upon contact lengths and results in grinding. CIRP Ann Manuf Technol 35(1):249–253CrossRefGoogle Scholar
  72. 72.
    Wang Y, Lin B, Zhang X (2014) Research on the system matching model in ultrasonic vibration-assisted grinding. Int J Adv Manuf Technol 70(1–4):449–458CrossRefGoogle Scholar
  73. 73.
    Wang Y, Lin B, Wang S, Cao X (2014) Study on the system matching of ultrasonic vibration assisted grinding for hard and brittle materials processing. Int J Mach Tools Manuf 77:66–73CrossRefGoogle Scholar
  74. 74.
    Zhao B, Yan YY, Wu Y, Jiao F, Liu C (2006) Study on motion model of abrasive particle and surface formation mechanics under two dimensional ultrasonic grinding. In: Key Engineering Materials. Trans Tech Publ, pp 314–318Google Scholar
  75. 75.
    Liang Z, Wang X, Wu Y, Xie L, Liu Z, Zhao W (2012) An investigation on wear mechanism of resin-bonded diamond wheel in elliptical ultrasonic assisted grinding (EUAG) of monocrystal sapphire. J Mater Process Technol 212(4):868–876CrossRefGoogle Scholar
  76. 76.
    Wu Y, Nomura M, Kato M, Tachibana T (2003) Study of internal ultrasonic vibration assisted grinding of small holes,-construction of ultrasonic vibration spindle and its fundamental performances. J Jpn Soc Abras Technol 47(10):550Google Scholar
  77. 77.
    Uhlmann E, Hübert C (2006) Advances in ultrasonic assisted grinding of ceramic materials. In: Advances in science and technology. Trans Tech Publ, pp 1711–1716Google Scholar
  78. 78.
    Spur G, Holl S-E (1996) Ultrasonic assisted grinding of ceramics. J Mater Process Technol 62(4):287–293CrossRefGoogle Scholar
  79. 79.
    Peng Y, Wu Y, Liang Z, Guo Y, Lin X (2011) An experimental study of ultrasonic vibration-assisted grinding of polysilicon using two-dimensional vertical workpiece vibration. Int J Adv Manuf Technol 54(9–12):941–947CrossRefGoogle Scholar
  80. 80.
    Guo B, Zhao Q, Jackson M (2011) Ultrasonic vibration-assisted grinding of microstructured surfaces on silicon carbide ceramic materials. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture:0954405411423574Google Scholar
  81. 81.
    Vanparys M, Liu W, Lauwers B (2008) Influence of machining parameters and tool wear on the material removal mechanisms in the ultrasonic assisted grinding of Al2O3. In: Proceedings of the 3rd CIRP International Conference High Performance Cutting. pp 849–858Google Scholar
  82. 82.
    Dornfeld D, Min S, Takeuchi Y (2006) Recent advances in mechanical micromachining. CIRP Ann Manuf Technol 55(2):745–768CrossRefGoogle Scholar
  83. 83.
    Cook RF, Pharr GM (1990) Direct observation and analysis of indentation cracking in glasses and ceramics. J Am Ceram Soc 73(4):787–817CrossRefGoogle Scholar
  84. 84.
    Maksoud T, Mokbel A, Morgan J (1999) Evaluation of surface and sub-surface cracks of ground ceramic. J Mater Process Technol 88(1):222–243CrossRefGoogle Scholar
  85. 85.
    McNamara D, Alveen P, Carolan D, Murphy N, Ivanković A (2014) Micromechanical study of strength and toughness of advanced ceramics. Procedia Mater Sci 3:1810–1815CrossRefGoogle Scholar
  86. 86.
    Hammel E, Ighodaro O-R, Okoli O (2014) Processing and properties of advanced porous ceramics: an application based review. Ceram Int 40(10):15351–15370CrossRefGoogle Scholar
  87. 87.
    Shen J, Wang J, Jiang B, Xu X (2015) Study on wear of diamond wheel in ultrasonic vibration-assisted grinding ceramic. Wear 332:788–793CrossRefGoogle Scholar
  88. 88.
    Zhong Z, Venkatesh V (2009) Recent developments in grinding of advanced materials. Int J Adv Manuf Technol 41(5–6):468–480CrossRefGoogle Scholar
  89. 89.
    Gao G, Kong Q, Zhao B, Liu C (2006) Research on plastic removal mechanism of engineering ceramics grinding with ultrasonic assistance. In: Technology and Innovation Conference, 2006. ITIC 2006. International. IET, pp 214–218Google Scholar
  90. 90.
    Bifano TG, Dow TA, Scattergood RO (1991) Ductile-regime grinding: a new technology for machining brittle materials. J Eng Ind 113(2):184–189CrossRefGoogle Scholar
  91. 91.
    Warnecke G, Rosenberger U, Milberg J (1995) Basics of process parameter selection in grinding of advanced ceramics. CIRP Ann Manuf Technol 44(1):283–286CrossRefGoogle Scholar
  92. 92.
    Zhao B, Zhang X, Liu C, Jiao F, Zhu XS (2005) Study on ultrasonic vibration grinding character of nano ZrO2 ceramics. In: Key Engineering Materials. Trans Tech Publ, pp 45–50Google Scholar
  93. 93.
    Dai J, Ding W, Zhang L, Xu J, Su H (2015) Understanding the effects of grinding speed and undeformed chip thickness on the chip formation in high-speed grinding. Int J Adv Manuf Technol 81(5–8):995–1005CrossRefGoogle Scholar
  94. 94.
    Kizaki T, Ito Y, Tanabe S, Kim Y, Sugita N, Mitsuishi M (2016) Laser-assisted machining of zirconia ceramics using a diamond bur. Procedia CIRP 42:497–502CrossRefGoogle Scholar
  95. 95.
    Marshall DB, Lawn BR (1985) Indentation of brittle materials. In: Microindentation techniques in materials science and engineering. ASTM InternationalGoogle Scholar
  96. 96.
    Lawn B, Marshall D (1979) Hardness, toughness, and brittleness: an indentation analysis. J Am Ceram Soc 62(7–8):347–350CrossRefGoogle Scholar
  97. 97.
    Wang C, Fang Q, Chen J, Liu Y, Jin T (2015) Subsurface damage in high-speed grinding of brittle materials considering kinematic characteristics of the grinding process. The International Journal of Advanced Manufacturing Technology:1–12Google Scholar
  98. 98.
    Yan YY, Zhao B, Wu Y, Liu CS, Zhu XS (2006) Study on material removal mechanism of fine-crystalline ZrO2 ceramics under two dimensional ultrasonic grinding. In: Materials Science Forum. Trans Tech Publ, pp 532–535Google Scholar
  99. 99.
    Arif M, Rahman M, San WY (2011) Analytical model to determine the critical feed per edge for ductile–brittle transition in milling process of brittle materials. Int J Mach Tools Manuf 51(3):170–181CrossRefGoogle Scholar
  100. 100.
    Bifano TG, Fawcett SC (1991) Specific grinding energy as an in-process control variable for ductile-regime grinding. Precis Eng 13(4):256–262CrossRefGoogle Scholar
  101. 101.
    Nakamura M, Sumomogi T, Endo T (2003) Evaluation of surface and subsurface cracks on nano-scale machined brittle materials by scanning force microscope and scanning laser microscope. Surf Coat Technol 169:743–747CrossRefGoogle Scholar
  102. 102.
    Marinescu ID (2006) Handbook of advanced ceramics machining. CRC PressGoogle Scholar
  103. 103.
    Molaie M, Akbari J, Movahhedy M (2016) Ultrasonic assisted grinding process with minimum quantity lubrication using oil-based nanofluids. J Clean Prod 129:212–222CrossRefGoogle Scholar
  104. 104.
    Zhou M, Wang X, Ngoi B, Gan J (2002) Brittle–ductile transition in the diamond cutting of glasses with the aid of ultrasonic vibration. J Mater Process Technol 121(2):243–251CrossRefGoogle Scholar
  105. 105.
    Liu K, Li X, Rahman M, Neo K, Liu X (2007) A study of the effect of tool cutting edge radius on ductile cutting of silicon wafers. Int J Adv Manuf Technol 32(7–8):631–637CrossRefGoogle Scholar
  106. 106.
    Klocke F, Brinksmeier E, Evans CJ, Howes T, Inasaki I, Minke E, Tönshoff H, Webster J, Stuff D (1997) High-speed grinding-fundamentals and state of the art in Europe, Japan, and the USA. CIRP Ann Manuf Technol 46(2)Google Scholar
  107. 107.
    Peng Y, Liang Z, Wu Y, Guo Y, Wang C (2012) Characteristics of chip generation by vertical elliptic ultrasonic vibration-assisted grinding of brittle materials. Int J Adv Manuf Technol 62(5–8):563–568CrossRefGoogle Scholar
  108. 108.
    Prabhakar D, Ferreira P, Haselkorn M (1992) An experimental investigation of material removal rates in rotary ultrasonic machining. Trans North Am Manuf Res Inst SME 20:211–218Google Scholar
  109. 109.
    Lee T, Chan C (1997) Mechanism of the ultrasonic machining of ceramic composites. J Mater Process Technol 71(2):195–201CrossRefGoogle Scholar
  110. 110.
    Park KH, Kim KT, Hong YH, Choi HJ, Choi YJ Study on effect of ultrasonic vibration in machining of alumina ceramic. In: Key Engineering Materials, 2012. Trans Tech Publ, pp 311–316Google Scholar
  111. 111.
    K-l KUO, C-c TSAO (2012) Rotary ultrasonic-assisted milling of brittle materials. Trans Nonferrous Metals Soc China 22:s793–s800CrossRefGoogle Scholar
  112. 112.
    Suzuki K, Uematsu T, Makizaki T, Iwai M (2000) Ultrasonic grinding utilizing a stator of an ultrasonic motor. In: Proceedings of JSME Conference Manufacturing and Machine Tool. pp 183–184Google Scholar
  113. 113.
    Zahedi A, Tawakoli T, Akbari J (2015) Energy aspects and workpiece surface characteristics in ultrasonic-assisted cylindrical grinding of alumina–zirconia ceramics. Int J Mach Tools Manuf 90:16–28CrossRefGoogle Scholar
  114. 114.
    Sayuti M, Sarhan AA, Fadzil M, Hamdi M (2012) Enhancement and verification of a machined surface quality for glass milling operation using CBN grinding tool—Taguchi approach. Int J Adv Manuf Technol 60(9–12):939–950CrossRefGoogle Scholar
  115. 115.
    Adibi H, Rezaei S, Sarhan AA (2014) Investigation on using high-pressure fluid jet in grinding process for less wheel loaded areas. Int J Adv Manuf Technol 70(9–12):2233–2240CrossRefGoogle Scholar
  116. 116.
    Fan X, Miller MH (2006) Force analysis for grinding with segmental wheels. Mach Sci Technol 10(4):435–455CrossRefGoogle Scholar
  117. 117.
    Nik MG, Movahhedy MR, Akbari J (2012) Ultrasonic-assisted grinding of Ti6Al4V alloy. Procedia CIRP 1:353–358CrossRefGoogle Scholar
  118. 118.
    Tawakoli T, Azarhoushang B (2009) Effects of ultrasonic assisted grinding on CBN grinding wheels performance. In: ASME 2009 International Manufacturing Science and Engineering Conference. American Society of Mechanical Engineers, pp 209–214Google Scholar
  119. 119.
    Hanasaki S, Fujivara J, Wada T, Hasegawa Y (1994) Vibratory creep feed grinding. Nippon Kikai Gakkai Ronbunshu C Hen 60(573):1829–1834Google Scholar
  120. 120.
    Zhang B, Howes TD (1995) Subsurface evaluation of ground ceramics. CIRP Ann Manuf Technol 44(1):263–266CrossRefGoogle Scholar
  121. 121.
    Zhang D, Li C, Jia D, Zhang Y (2014) Investigation into engineering ceramics grinding mechanism and the influential factors of the grinding force. Int J Control Autom 7(4):19–34MathSciNetCrossRefGoogle Scholar
  122. 122.
    Zhang HL, Zhang JH, Huo MY (2006) Study on ultrasonic vibration assisted grinding in theory. In: Materials Science Forum. Trans Tech Publ, pp 773–776Google Scholar
  123. 123.
    Feng P, Liang G, Zhang J (2014) Ultrasonic vibration-assisted scratch characteristics of silicon carbide-reinforced aluminum matrix composites. Ceram Int 40(7):10817–10823CrossRefGoogle Scholar
  124. 124.
    Xiao X, Zheng K, Liao W, Meng H (2016) Study on cutting force model in ultrasonic vibration assisted side grinding of zirconia ceramics. Int J Mach Tools Manuf 104:58–67CrossRefGoogle Scholar
  125. 125.
    Wang Y, Lin B, Cao X, Wang S (2014) An experimental investigation of system matching in ultrasonic vibration assisted grinding for titanium. J Mater Process Technol 214(9):1871–1878CrossRefGoogle Scholar
  126. 126.
    Nomura M, Wu Y, Kuriyagawa T (2007) Investigation of internal ultrasonically assisted grinding of small holes: effect of ultrasonic vibration in truing and dressing of small CBN grinding wheel. J Mech Sci Technol 21(10):1605–1611CrossRefGoogle Scholar
  127. 127.
    Liang Z, Wang X, Zhao W, Wu Y, Sato T, Lin W (2010) A feasibility study on elliptical ultrasonic assisted grinding of sapphire substrate. Int J Abras Technol 3(3):190–202CrossRefGoogle Scholar
  128. 128.
    Gupta R, Shishodia K, Sekhon G (2001) Optimization of grinding process parameters using enumeration method. J Mater Process Technol 112(1):63–67CrossRefGoogle Scholar
  129. 129.
    Bhaduri D, Soo S, Aspinwall D, Novovic D, Harden P, Bohr S, Martin D (2012) A study on ultrasonic assisted creep feed grinding of nickel based superalloys. Procedia CIRP 1:359–364CrossRefGoogle Scholar
  130. 130.
    Tawakoli T, Westkämper E, Azarhoushang B (2009) Effects of vibration-assisted grinding on wear behavior of vitrified bond Al2O3 wheel. In: Advanced Materials Research. Trans Tech Publ, pp 21–26Google Scholar
  131. 131.
    Jackson M, Davis C, Hitchiner M, Mills B (2001) High-speed grinding with CBN grinding wheels—applications and future technology. J Mater Process Technol 110(1):78–88CrossRefGoogle Scholar
  132. 132.
    Fathima K, Kumar AS, Rahman M, Lim H (2003) A study on wear mechanism and wear reduction strategies in grinding wheels used for ELID grinding. Wear 254(12):1247–1255CrossRefGoogle Scholar
  133. 133.
    Negishi N (2003) Elliptical vibration assisted machining with single crystal diamond toolsGoogle Scholar
  134. 134.
    Shamoto E, Moriwaki T (1999) Ultaprecision diamond cutting of hardened steel by applying elliptical vibration cutting. CIRP Ann Manuf Technol 48(1):441–444CrossRefGoogle Scholar
  135. 135.
    Mahaddalkar PM, Miller MH (2014) Force and thermal effects in vibration-assisted grinding. Int J Adv Manuf Technol 71(5–8):1117–1122CrossRefGoogle Scholar
  136. 136.
    Ding W, Zhu Y, Zhang L, Xu J, Fu Y, Liu W, Yang C (2015) Stress characteristics and fracture wear of brazed CBN grains in monolayer grinding wheels. Wear 332:800–809CrossRefGoogle Scholar
  137. 137.
    Izman S, Venkatesh V (2007) Gelling of chips during vertical surface diamond grinding of BK7 glass. J Mater Process Technol 185(1):178–183CrossRefGoogle Scholar
  138. 138.
    Munoz-Tabares J, Jiménez-Piqué E, Reyes-Gasga J, Anglada M (2011) Microstructural changes in ground 3Y-TZP and their effect on mechanical properties. Acta Mater 59(17):6670–6683CrossRefGoogle Scholar
  139. 139.
    Shimada S, Tanaka H, Higuchi M, Yamaguchi T, Honda S, Obata K (2004) Thermo-chemical wear mechanism of diamond tool in machining of ferrous metals. CIRP Ann Manuf Technol 53(1):57–60CrossRefGoogle Scholar
  140. 140.
    Weber H, Herberger J, Pilz R (1984) Turning of machinable glass ceramics with an ultrasonically vibrated tool. CIRP Ann Manuf Technol 33(1):85–87CrossRefGoogle Scholar
  141. 141.
    Hosokawa A, Ueda T, Yunoki T (2006) Laser dressing of metal bonded diamond wheel. CIRP Ann Manuf Technol 55(1):329–332CrossRefGoogle Scholar
  142. 142.
    Zheng K, Li Z, Liao W, Xiao X (2016) Friction and wear performance on ultrasonic vibration assisted grinding dental zirconia ceramics against natural tooth. Journal of the Brazilian Society of Mechanical Sciences and Engineering:1–11Google Scholar
  143. 143.
    Suh C-M, Bae K-S, Suh M-S (2008) Wear behavior of diamond wheel for grinding optical connector ferrule—FEA and wear test. J Mech Sci Technol 22(11):2009–2015CrossRefGoogle Scholar
  144. 144.
    Paul E, Evans CJ, Mangamelli A, McGlauflin ML, Polvani RS (1996) Chemical aspects of tool wear in single point diamond turning. Precis Eng 18(1):4–19CrossRefGoogle Scholar
  145. 145.
    Moneim MEA, Abdou S (1997) Comments on the wear mechanisms of impregnated diamond bits. Wear 205(1):228–230CrossRefGoogle Scholar
  146. 146.
    Feng J, Kim B, Shih A, Ni J (2009) Tool wear monitoring for micro-end grinding of ceramic materials. J Mater Process Technol 209(11):5110–5116CrossRefGoogle Scholar
  147. 147.
    Hitchiner M (1999) Technological advances in creep feed grinding of superalloys with CBN. In: 3rd International Machining and Grinding Conference SME, Cincinnati, Ohio. pp 4–7Google Scholar
  148. 148.
    Kwak J-S, Ha M-K (2004) Detection of dressing time using the grinding force signal based on the discrete wavelet decomposition. Int J Adv Manuf Technol 23(1–2):87–92CrossRefGoogle Scholar
  149. 149.
    Adibi H, Rezaei S, Sarhan AA (2014) Grinding wheel loading evaluation using digital image processing. J Manuf Sci Eng 136(1):011012CrossRefGoogle Scholar
  150. 150.
    Li S, Wu Y, Fujimoto M, Nomura M (2016) Improving the working surface condition of electroplated cubic boron nitride grinding Quill in surface grinding of Inconel 718 by the assistance of ultrasonic vibration. J Manuf Sci Eng 138(7):071008CrossRefGoogle Scholar
  151. 151.
    Adibi H, Rezaei S, Sarhan AA (2013) Analytical modeling of grinding wheel loading phenomena. Int J Adv Manuf Technol 68(1–4):473–485CrossRefGoogle Scholar
  152. 152.
    Alberdi R, Sanchez J, Pombo I, Ortega N, Izquierdo B, Plaza S, Barrenetxea D (2011) Strategies for optimal use of fluids in grinding. Int J Mach Tools Manuf 51(6):491–499CrossRefGoogle Scholar
  153. 153.
    Nomura M, Wu YB, Kuriyagawa T, Kawashima T, Shibata T (2009) Effects of grain size and concentration of grinding wheel in ultrasonically assisted grinding. In: Key engineering materials. Trans Tech Publ, pp 283–288Google Scholar
  154. 154.
    Peng D, Kang Y, Hwang R, Shyr S, Chang Y (2009) Tribological properties of diamond and SiO 2 nanoparticles added in paraffin. Tribol Int 42(6):911–917CrossRefGoogle Scholar
  155. 155.
    Zhang P, Miller MH (2007 Wheel loading reduction with vibration assisted grinding. In: ASPE Spring Topical MeetingGoogle Scholar
  156. 156.
    Bellows G (1972) Applying surface integrity principles in jet engine production. Metals Eng Q 12:55–58Google Scholar
  157. 157.
    Yan YY, Liu JL, Zhao B (2011) Study on the prediction of surface roughness of ZTA ceramics under ultrasonic assisted grinding. In: Advanced materials research. Trans Tech Publ, pp 1325–1328Google Scholar
  158. 158.
    Chen MJ, Li D, Dong S, Zhang FH (2004) Factors influencing the surface quality during ultra-precision grinding of brittle materials in ductile mode. In: Key engineering materials. Trans Tech Publ, pp 201–206Google Scholar
  159. 159.
    Chen H, Tang J, Zhou W (2013) An experimental study of the effects of ultrasonic vibration on grinding surface roughness of C45 carbon steel. Int J Adv Manuf Technol 68(9–12):2095–2098CrossRefGoogle Scholar
  160. 160.
    Wang Y, Moon KS, Miller MH (1998) A new method for improving the surface grinding process. J Manuf Sci Prod 1(3):159–168Google Scholar
  161. 161.
    Park K-H, Hong Y-H, Kim K-T, Lee S-W, Choi H-Z, Choi Y-J (2013) Understanding of ultrasonic assisted machining with diamond grinding tool. Mod Mech Eng 4(01):1CrossRefGoogle Scholar
  162. 162.
    Klocke F, Rubenach O (2000) Ultrasonic-assisted diamond turning of glass and steel. Ind Diam Rev 60(586):227Google Scholar
  163. 163.
    Blackley W, Scattergood RO (1991) Ductile-regime machining model for diamond turning of brittle materials. Precis Eng 13(2):95–103CrossRefGoogle Scholar
  164. 164.
    Jirapattarasilp K, Rukijkanpanich J (2007) The experiment of high-speed grinding of a gemstone: cubic zirconia. Int J Adv Manuf Technol 33(11–12):1136–1142CrossRefGoogle Scholar
  165. 165.
    El-Khabeery M, Fattouh M (1989) Residual stress distribution caused by milling. Int J Mach Tools Manuf 29(3):391–401CrossRefGoogle Scholar
  166. 166.
    Subhas B, Bhat R, Shivanand I (1996) Development of computer aided technique for determination of residual stresses due to machining of jet engine components made of Inconel 718 nickel based superalloy. In: International Manufacturing Engineering Conference. pp 212–214Google Scholar
  167. 167.
    Brinksmeier E, Tönshoff H (1985) X-ray stress measurement—a tool for the study and layout of machining processes. CIRP Ann Manuf Technol 34(1):485–490CrossRefGoogle Scholar
  168. 168.
    Zhao ML, Guo QC, Zhao B (2014) Influence of grinding parameters on residual stress of Nano-ZrO2 ceramics. In: Advanced Materials Research. Trans Tech Publ, pp 119–122Google Scholar
  169. 169.
    Ruud C (1982) A review of selected non-destructive methods for residual stress measurement. NDT Int 15(1):15–23CrossRefGoogle Scholar
  170. 170.
    Lange F (1980) Compressive surface stresses developed in ceramics by an oxidation-induced phase change. J Am Ceram Soc 63(1–2):38–40CrossRefGoogle Scholar
  171. 171.
    Portu G, Conoci S (1997) Simplified equation for evaluating the influence of surface residual stresses on the toughness of zirconia ceramics. J Am Ceram Soc 80(12):3242–3244CrossRefGoogle Scholar
  172. 172.
    Basu B, Vleugels J, Van der Biest O (2001) Transformation behavior of yttria stabilized tetragonal zirconia polycrystal–TiB 2 composites. J Mater Res 16(07):2158–2169CrossRefGoogle Scholar
  173. 173.
    Aubry A, Armanet F, Beranger G, Lebrun J, Maeder G (1988) Measurement of residual stresses by X-ray diffraction in a NiNio system obtained by high temperature oxidation. Acta Metall 36(10):2779–2786CrossRefGoogle Scholar
  174. 174.
    Richmond O, Leslie W, Wriedt H (1964) Theory of residual stresses due to chemical concentration gradients. Trans ASM 57(1):294–300Google Scholar
  175. 175.
    GREEN DJ, Lange F, JAMES MR (1983) Factors influencing residual surface stresses due to a stress-induced phase Bansformation. J Am Ceram Soc 66(9):623–629CrossRefGoogle Scholar
  176. 176.
    Zhang X, Zhao CY, Du BY (2011) The machined surface residual stress of nano-ceramics with two-dimensional ultrasonic vibration assisted grinding. In: Key engineering materials. Trans Tech Publ, pp 637–642Google Scholar
  177. 177.
    Li Y, Zheng N, Li H, Hou J, Lei X, Chen X, Yuan Z, Guo Z, Wang J, Guo Y (2011) Morphology and distribution of subsurface damage in optical fused silica parts: bound-abrasive grinding. Appl Surf Sci 257(6):2066–2073CrossRefGoogle Scholar
  178. 178.
    Zhang B, Zheng X, Tokura H, Yoshikawa M (2003) Grinding induced damage in ceramics. J Mater Process Technol 132(1):353–364CrossRefGoogle Scholar
  179. 179.
    Rekow D, Thompson V (2005) Near-surface damage-a persistent problem in crowns obtained by computer-aided design and manufacturing. Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine 219 (4):233–243Google Scholar
  180. 180.
    Pfeiffer W, Hollstein T (1993) Damage determination and strength prediction of machined ceramics by x-ray diffraction techniques. Machining of Advanced Materials: 235–245Google Scholar
  181. 181.
    Su JK, Lin B, Wang L (2014) Study on the model of surface crack depth in ceramics grinding. In: Advanced Materials Research. Trans Tech Publ, pp 212–217Google Scholar
  182. 182.
    Wang Z, Wu Y, Dai Y, Li S (2008) Subsurface damage distribution in the lapping process. Appl Opt 47(10):1417–1426CrossRefGoogle Scholar
  183. 183.
    Oliveira J, Alves SM (2006) Development of environmentally friendly fluid for CBN grinding. CIRP Ann Manuf Technol 55(1):343–346CrossRefGoogle Scholar
  184. 184.
    Mao C, Tang X, Zou H, Zhou Z, Yin W (2012) Experimental investigation of surface quality for minimum quantity oil–water lubrication grinding. Int J Adv Manuf Technol 59(1–4):93–100CrossRefGoogle Scholar
  185. 185.
    Fratila D, Caizar C (2011) Application of Taguchi method to selection of optimal lubrication and cutting conditions in face milling of AlMg 3. J Clean Prod 19(6):640–645CrossRefGoogle Scholar
  186. 186.
    Chen Z, Atmadi A, Stephenson DA, Liang SY, Patri KV (2000) Analysis of cutting fluid aerosol generation for environmentally responsible machining. CIRP Ann Manuf Technol 49(1):53–56CrossRefGoogle Scholar
  187. 187.
    Alves SM, de Oliveira JFG (2006) Development of new cutting fluid for grinding process adjusting mechanical performance and environmental impact. J Mater Process Technol 179(1):185–189CrossRefGoogle Scholar
  188. 188.
    Hu KH, Huang F, Hu XG, Xu YF, Zhou YQ (2011) Synergistic effect of nano-MoS2 and anatase nano-TiO2 on the lubrication properties of MoS2/TiO2 nano-clusters. Tribol Lett 43(1):77–87CrossRefGoogle Scholar
  189. 189.
    Tawakoli T, Hadad M, Sadeghi MH, Daneshi A, Sadeghi B (2011) Minimum quantity lubrication in grinding: effects of abrasive and coolant–lubricant types. J Clean Prod 19(17):2088–2099CrossRefGoogle Scholar
  190. 190.
    Balan A, Vijayaraghavan L, Krishnamurthy R (2013) Minimum quantity lubricated grinding of Inconel 751 alloy. Mater Manuf Process 28(4):430–435CrossRefGoogle Scholar
  191. 191.
    Sadeghi M, Haddad M, Tawakoli T, Emami M (2009) Minimal quantity lubrication-MQL in grinding of Ti–6Al–4V titanium alloy. Int J Adv Manuf Technol 44(5–6):487–500CrossRefGoogle Scholar
  192. 192.
    Verma A, Jiang W, Abu Safe HH, Brown WD, Malshe AP (2008) Tribological behavior of deagglomerated active inorganic nanoparticles for advanced lubrication. Tribol Trans 51(5):673–678CrossRefGoogle Scholar
  193. 193.
    Zhang Y, Li C, Jia D, Zhang D, Zhang X (2015) Experimental evaluation of MoS 2 nanoparticles in jet MQL grinding with different types of vegetable oil as base oil. J Clean Prod 87:930–940CrossRefGoogle Scholar
  194. 194.
    Kalita P, Malshe AP, Kumar SA, Yoganath V, Gurumurthy T (2012) Study of specific energy and friction coefficient in minimum quantity lubrication grinding using oil-based nanolubricants. J Manuf Process 14(2):160–166CrossRefGoogle Scholar
  195. 195.
    Qin N, Pei Z, Treadwell C, Guo D (2009) Physics-based predictive cutting force model in ultrasonic-vibration-assisted grinding for titanium drilling. J Manuf Sci Eng 131(4):041011CrossRefGoogle Scholar
  196. 196.
    Emami M, Sadeghi MH, Sarhan AAD, Hasani F (2014) Investigating the minimum quantity lubrication in grinding of Al 2 O 3 engineering ceramic. J Clean Prod 66:632–643CrossRefGoogle Scholar
  197. 197.
    Irani RA, Bauer RJ, Warkentin A (2007) Development of a new cutting fluid delivery system for creepfeed grinding. Int J Manuf Technol Manag 12(1–3):108–126Google Scholar
  198. 198.
    Rowe WB (2013) Principles of modern grinding technology. William AndrewGoogle Scholar
  199. 199.
    Wang X, Wu Y, Wang J, Xu W, Kato M (2005) Absorbed energy in laser truing of a small vitrified CBN grinding wheel. J Mater Process Technol 164:1128–1133CrossRefGoogle Scholar
  200. 200.
    Tawakoli T, Rasifard A, Azarhoushang B (2008) Dressing of CBN grinding wheels with ultrasonic assistance. Int J Mechatronics Manuf Syst 1(4):321–331Google Scholar
  201. 201.
    Ikuse Y, Nonokawa T, Kawabata N, Kamo T, Yuzawa Y, Unno K (1996) Development of new ultrasonic dressing equipment. Int J Japan Soc Precis Eng 30(3):217–222Google Scholar
  202. 202.
    Jiao F, Zhao B, Zhu XS, Fan Q (2006) Ultrasonic dressing of grinding wheel and its influence on grinding quality. In: Key Engineering Materials. Trans Tech Publ, pp 62–65Google Scholar
  203. 203.
    Sroka F (2005) Konditionieren von Diamantschleifscheiben. Fraunhofer-IRB-VerlagGoogle Scholar
  204. 204.
    Chen W, Kuriyagawa T, Huang H, Yosihara N (2005) Machining of micro aspherical mould inserts. Precis Eng 29(3):315–323CrossRefGoogle Scholar
  205. 205.
    Murata R, Okano K, Tsutsumi C (1985) Grinding of structural ceramics. In: Proceedings of the Milton C. Shaw Grinding Symposium, PED. vol 1. pp 261–272Google Scholar
  206. 206.
    Ohmori H, Nakagawa T (1990) Mirror surface grinding of silicon wafers with electrolytic in-process dressing. CIRP Ann Manuf Technol 39(1):329–332CrossRefGoogle Scholar
  207. 207.
    Sanchez JA, Ortega N, de Lacalle LNL, Lamikiz A, Marañon JA (2006) Analysis of the electro discharge dressing (EDD) process of large-grit size cBN grinding wheels. Int J Adv Manuf Technol 29(7–8):688–694CrossRefGoogle Scholar
  208. 208.
    Jackson MJ, Khangar A, Chen X, Robinson GM, Venkatesh V, Dahotre N (2007) Laser cleaning and dressing of vitrified grinding wheels. J Mater Process Technol 185(1):17–23CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London 2017

Authors and Affiliations

  1. 1.Centre of Advanced Manufacturing and Material Processing, Department of Mechanical EngineeringUniversity of MalayaKuala LumpurMalaysia
  2. 2.Mechanical Engineering DepartmentKing Fahd University of Petroleum and MineralsDhahranSaudi Arabia
  3. 3.Department of Mechanical Engineering, Faculty of EngineeringAssiut UniversityAssiutEgypt

Personalised recommendations