Force analysis of magnetic abrasive nano-finishing of magnetic and non-magnetic materials
- 106 Downloads
Finishing is the final operation during manufacturing process of a component. It is time consuming, difficult, and usually a costly operation. Finishing cost can be as high as 15 % of the total production cost. Magnetic Abrasive Finishing (MAF) is an advanced finishing process in which a mixture of non-ferromagnetic abrasive particles and ferromagnetic carbonyl iron particles (CIPs) is used to do finishing operation with the aid of magnetic force. The iron particles form a flexible chain matrix in which the abrasive particles are trapped in between or within the chains. This is called flexible magnetic abrasive brush (FMAB), which when given a relative motion against a (metal/non-metal) surface, it finishes the surface. The present work deals with the effect of the process parameters such as applied magnetic field, concentration of abrasive particles and iron particles in FMAB, and rotational speed of magnet on the finishing forces that are generated during vertical MAF of ferromagnetic (EN-8) and non-ferromagnetic material (brass) flat workpieces. Empirical models for force prediction have been developed based on the experimental results. Effect of the applied magnetic field is seen to have the most significant contribution among all the input parameters. Percentage of oil in FMAB is not a significant factor for normal force, but it is a significant factor to the tangential force. The tangential force increases up to 3 % of oil content in FMAB, and it starts decreasing in the range of 3 to 5 % oil content.
KeywordsMAF Finishing forces Surface roughness Flexible magnetic abrasive brush
Unable to display preview. Download preview PDF.
- 1.Shinmura T, Takazawa K, Hatano E, Toshio A (1984) Study on magnetic abrasive process—finishing characteristics. Bull Jpn Soc Precis Eng 18(4):347–345Google Scholar
- 2.Shinmura T, Takazawa K, Hatano E, Toshio A (1985) Study on magnetic abrasive process—process principle and finishing possibility. Bull Jpn Soc of Precis Eng 19(1):54–55Google Scholar
- 3.Shinmura T, Takazawa K, Hatano E (1985) Study on magnetic abrasive process—application to edge finishing. Bull Jpn Soc of Precis Eng 19(3):218–220Google Scholar
- 4.Shinmura T, Takazawa K, Hatano E (1987) Study on magnetic abrasive finishing—effects of various types of magnetic abrasives on finishing characteristics. Bull Jpn Soc Precis Eng 21(2):139–141Google Scholar
- 7.Yamaguchi H. and Shinmura T., “Magnetic abrasive finishing of inner surfaces of tubes”, Proceedings, International Symposium for Electro-machining, EPFL Lausanne, Switzerland (April 17–21, 1995), pp. 963–976.Google Scholar
- 8.Yamaguchi H, Shinmura T (2000) Study of an internal magnetic abrasive finishing using a pole rotation system: discussion of the characteristic abrasive behavior. Precis Eng J Int Soc Precis Eng Nanotechnol 24:237–244Google Scholar
- 11.Shinmura T, Takazawa K, Hatano E (1985) Study on magnetic abrasive process—application to plane finishing. Bull Jpn Soc Precis Eng 19(4):289–291Google Scholar
- 12.Shinmura T, Aizawa T (1989) Study on magnetic abrasive finishing process. Bull Jpn Soc Precis Eng 23(3):236–239Google Scholar
- 19.Cochran WG, Cox GM (1962) Experimental design. John Wiley and Sons, New YorkGoogle Scholar
- 20.Kusin Kumar Saran, Force analysis of magnetic abrasive finishing of non-ferromagnetic materials, M. Tech. Thesis, Indian Institute of Technology Kanpur (India), 2004.Google Scholar
- 21.D. K. Singh, Investigations into magnetic abrasive finishing of plane surfaces, Ph.D. Thesis, Indian Institute of Technology Kanpur (India), 2006.Google Scholar