Advertisement

Interactive influence of linked characteristics during machining of thin-walled parts

  • Beizhi Li
  • XiaoYan ZuoEmail author
  • Jianguo Yang
  • Xiaohui Jiang
  • Junhui Ni
ORIGINAL ARTICLE

Abstract

Today, characteristic-based quality analysis has been popular in academia and industry with its ability to show the error evolution of parts during manufacturing. To date, research on characteristics mainly focuses on characteristic sequence, characteristic extraction, characteristic deflection, and characteristic identification, which are all for individual characteristics. However, a key characteristic is not only influenced by each machining itself but also by further machining linked-characteristics. This paper analyzes manufacturing characteristic interactions and presents algorithms, simulation, and experiment for linked characteristic interactions in manufacturing process planning. Firstly, a geometric model shows the tolerance/datum interactions. Secondly, thin-walled parts of aluminum alloy are used to analyze and simulate the machining interactions based on ANSYS system. By analyzing the simulation and experiment results, discussion and evaluation of the results and conclusions are submitted.

Keywords

Linked characteristics Geometric interactions Machining interactions Thin-walled parts 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Chen W, Xue J, Tang D, Chen H, Qu S (2009) Deformation prediction and error compensation in multilayer milling processes for thin-walled parts. Int J Mach Tools Manuf 49(11):859–864CrossRefGoogle Scholar
  2. 2.
    Liao YG, Hu SJ (2001) An integrated model of a fixture–workpiece system for surface quality prediction. Int J Adv Manuf Technol 17:810–818CrossRefGoogle Scholar
  3. 3.
    Qin G, Zhang W, Wu Z, Wan M (2007) Systematic modeling of workpiece-fixture geometric default and compliance for the prediction of workpiece machining error. J Manuf Sci Eng 129:789–801CrossRefGoogle Scholar
  4. 4.
    Liu S, Zheng L, Zhang Z, Li Z, Liu D (2007) Optimization of the number and positions of fixture locators in the peripheral milling of a low-rigidity workpiece. Int J Adv Manuf Technol 33:668–676CrossRefGoogle Scholar
  5. 5.
    Wang MY (2003) Contact force prediction and force closure analysis of a fixtured rigid workpiece with friction. J Manuf Sci Eng 125:325–332CrossRefGoogle Scholar
  6. 6.
    Wan XJ, Xiong CH, Wang XF, Zhang XM, Xiong YL (2010) A machining-feature-driven approach to locating scheme in multi-axis milling. Int J Mach Tools Manuf 50:42–50CrossRefGoogle Scholar
  7. 7.
    Heo E-Y, Kim DW, Lee JY, Lee CS, Chen FF (2011) High speed pocket milling planning by feature-based machining area partitioning. Robot Comput Integr Manuf 27:706–713CrossRefGoogle Scholar
  8. 8.
    Hayes C (1990) Machining planning: a model of an expert level planning process, Ph.D. Dissertation, Carnegie Mellon University, USAGoogle Scholar
  9. 9.
    Sormaz D (2000) Modeling of manufacturing feature interactions for automated process planning. J Manuf Syst 19:28–45CrossRefGoogle Scholar
  10. 10.
    Chen CLP, Le Clair SR (1994) Integration of design and manufacturing: solving setup generation and feature sequencing using an unsupervised learning approach. Comput Aided Des 26:59–75CrossRefGoogle Scholar
  11. 11.
    Dipper T, Xu X, Klemm P (2011) Defining, recognizing and representing feature interactions in a feature-based data model. Robot Comput Integr Manuf 27(1):101–114CrossRefGoogle Scholar
  12. 12.
    Deja M, Siemiatkowski MS (2013) Feature-based generation of machining process plans for optimised parts manufacture. J Intell Manuf 24:831–846CrossRefGoogle Scholar
  13. 13.
    Sunil VB, Pande SS (2009) Automatic recognition of machining features using artificial neural networks. Int J Adv Manuf Technol 41:932–947CrossRefGoogle Scholar
  14. 14.
    Hart AJ, Slocum A, Willoughby P (2004) Kinematic coupling interchangeability. Precis Eng 28:1–15CrossRefGoogle Scholar
  15. 15.
    Huang Q, Shi J, Yuan J (2003) Part dimensional error and its propagation modeling in multi-operational machining processes. J Manuf Sci Eng 125(2):255–262CrossRefGoogle Scholar
  16. 16.
    Ding Y, Ceglarek D, Shi J (2002) Fault diagnosis of multistage manufacturing processes by using state space approach. J Manuf Sci Eng 124(2):313–322CrossRefGoogle Scholar
  17. 17.
    Camelio JA, Hu SJ, Marin S (2004) Compliant assembly variation analysis using components geometric covariance. J Manuf Sci Eng 126(2):355–360CrossRefGoogle Scholar
  18. 18.
    Liu Z, Wang L (2007) Sequencing of interacting prismatic machining features for process planning. Comput Ind 58:295–303CrossRefGoogle Scholar
  19. 19.
    Bravo U, Altuzarra O, Lo´pez de Lacalle LN, Sa´nchez JA, Campa FJ (2005) Stability limits of milling considering the flexibility of the workpiece and the machine. Int J Mach Tools Manuf 45:1669–1680CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London 2014

Authors and Affiliations

  • Beizhi Li
    • 1
  • XiaoYan Zuo
    • 1
    Email author
  • Jianguo Yang
    • 1
  • Xiaohui Jiang
    • 1
  • Junhui Ni
    • 1
    • 2
  1. 1.College of Mechanical EngineeringDonghua UniversityShanghaiChina
  2. 2.College of Mechanical EngineeringTaizhou UniversityTaizhouChina

Personalised recommendations