On surface integrity of miniature spur gears manufactured by wire electrical discharge machining

ORIGINAL ARTICLE

Abstract

This paper reports about investigations on some important aspects of surface integrity of the miniature spur gears manufactured by wire electrical discharge machining (WEDM) process. The investigations included study of variation of form errors (deviations in profile and lead) and surface roughness with discharge energy parameters, i.e., voltage and/or pulse-on time for the miniature gears. The effect of WEDM process on flank surface topography, bearing length parameters, microstructure, and microhardness for the best quality miniature gear were also studied. The manufactured miniature gears were of external spur type having 9.8 mm as outside diameter, 4.9-mm thickness, 0.7 mm as module, 12 teeth, and were made of brass. It was found that combination of low discharge energy parameters resulted in better form accuracy, surface finish, and microstructure ensuring enhanced service life and better functional characteristics of the WEDMed miniature gears. The best quality miniature gear had form errors (i.e., lead and profile deviations) as low as 5.4 μm, very little variation in the actual surface topography from the theoretical one, an average surface roughness of 1 μm, and maximum surface roughness within the entire evaluation length as 6.4 μm, showed consistent surface finish measured by other surface roughness parameters, good bearing area curve, and crack-free gear tooth surface without significant alteration in microhardness. Results of the present work demonstrate the superiority of the WEDM process over the conventional miniature gear manufacturing processes.

Keywords

Wire electrical discharge machining Miniature gear Surface integrity Form errors Topography Microstructure 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Grzesik W (2008) Advanced machining processes of metallic materials. Elsevier, OxfordGoogle Scholar
  2. 2.
    Hsu TR (2008) MEMS and microsystems design, manufacture and nano scale engineering. John Wiley & Sons, New JerseyGoogle Scholar
  3. 3.
    Bralla J (1998) Design for manufacturability handbook. Tata McGraw-Hill, New YorkGoogle Scholar
  4. 4.
    Davis JR (2005) Gear materials, properties and manufacture. ASM International, OhioGoogle Scholar
  5. 5.
    Townsend DP (2011) Dudley’s gear handbook. Tata McGraw-Hill, New DelhiGoogle Scholar
  6. 6.
    Benedict GF (1987) Nontraditional manufacturing processes. Marcel Dekker, New YorkGoogle Scholar
  7. 7.
    Jain VK (2002) Advanced machining processes. Allied Publishers, New DelhiGoogle Scholar
  8. 8.
    Davim PJ (2010) Surface integrity in machining. Springer, LondonCrossRefGoogle Scholar
  9. 9.
    Benavides GL, Bieg LF, Saavedra MP, Bryce EA (2002) High aspect ratio meso-scale parts enabled by wire micro-EDM. Microsyst Technol 8:395–401CrossRefGoogle Scholar
  10. 10.
    Di S, Haung R, Chi G (2006) Study on micro-machining by micro-WEDM. Proceedings of the 1st IEEE Conference on Nano/Micro Engineered and Molecular systems, Zhuhai, China, 615–619Google Scholar
  11. 11.
    Ali MY, Karim ANM, Adesta EYT, Ismail AF, Abdullah AA, Idris MN (2010) Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear. Int J Precis Eng Manuf 11(5):779–784CrossRefGoogle Scholar
  12. 12.
    Ali MY, Mohammad AS (2008) Experimental study of conventional WEDM for micro-fabrication. Mater Manuf Process 23(7):641–645CrossRefGoogle Scholar
  13. 13.
    Ho KH, Newman ST, Rahimifard S, Allen RD (2004) State of the art in wire electrical discharge machining. Int J Mach Tools Manuf 44:1247–1259CrossRefGoogle Scholar
  14. 14.
    Puri AB, Bhattacharyya B (2003) An analysis and optimization of the geometrical inaccuracy due to wire lag phenomenon in WEDM. Int J Mach Tools Manuf 43:151–159CrossRefGoogle Scholar
  15. 15.
    Mingqi L, Minghui L, Guangyao X (2005) Study on the variations of form and position of the wire electrode in WEDM-HS. Int J Adv Manuf Technol 25:929–934CrossRefGoogle Scholar
  16. 16.
    Liao YS, Huang JT, Chen YH (2004) A study to achieve fine surface finish in wire-EDM. J Mater Process Technol 149:165–171CrossRefGoogle Scholar
  17. 17.
    Puri AB, Bhattacharyya B (2005) Modeling and analysis of white layer depth in a wire-cut EDM process through response surface methodology. Int J Adv Manuf Technol 25:301–307CrossRefGoogle Scholar
  18. 18.
    Gupta K, Jain NK (2013) On micro-geometry of miniature gears manufactured by WEDM. Mater Manuf Process 28(10):1153–1159CrossRefGoogle Scholar
  19. 19.
    Gupta K, Jain NK (2013) Deviations in geometry of miniature gears fabricated by WEDM. (IMECE 66560). Proceedings of the ASME International Mechanical Engineering Congress and Exposition, San Diego, USAGoogle Scholar
  20. 20.
    Gupta K, Jain NK (2013) Analysis and optimization of surface finish of wire electrical discharge machined miniature gears. Proc IMechE B J Eng Manuf. doi:10.1177/0954405413508938 Google Scholar
  21. 21.
    Gupta K, Jain NK (2013) On productivity of wire electric discharge machining for manufacturing of miniature gears. Proceedings of the 2nd International Conference on Intelligent Robotics, Automation and Manufacturing, Indore, India, 383–394Google Scholar
  22. 22.
    Goch G (2003) Gear metrology. CIRP Ann 52(2):659–695CrossRefGoogle Scholar
  23. 23.
    Rebelo JC, Dias AM, Mesquita R, Vassalo P, Santos M (2000) An experimental study on electro-discharge machining and polishing of high strength copper-beryllium alloys. J Mater Process Technol 103:389–397CrossRefGoogle Scholar
  24. 24.
    Guha A, Rajurkar KP (1998) Effect of electrical discharge machining on the surface integrity of copper-beryllium alloys. Proceedings of the 12th Int. Symp Electromachining, Aachen, Germany, 309–319Google Scholar
  25. 25.
    Thao O, Joshi SS (2008) Analysis of heat affected zone in micro-electric discharge machining. Int J Manuf Technol Manag 13:201–213Google Scholar

Copyright information

© Springer-Verlag London 2014

Authors and Affiliations

  1. 1.Discipline of Mechanical EngineeringIndian Institute of Technology IndoreIndoreIndia

Personalised recommendations