Advertisement

Machining strategy in five-axis milling using balance of the transversal cutting force

  • Patrick Gilles
  • Guillaume Cohen
  • Frederic Monies
  • Walter Rubio
ORIGINAL ARTICLE

Abstract

Several solutions can be considered to resolve the problem of positioning a cutting tool on a free-form surface when five-axis milling. To choose a unique solution, in addition to the cutter–workpiece contact, an additional criterion can be taken into account. This may concern the local geometry of the surface or yet again the width milled to maximise the metal removal rate, but technological criteria relating to the cutting phenomenon and the quality of the surface produced are not considered. The present article introduces a strategy applying positioning combined with balancing of the transversal cutting force. This method involves using the ploughing effect of the milling cutters by simultaneously engaging the teeth located to the front of the cutter in relation to the feed movement and also those to the rear. The positioning obtained stabilises the cutter and contributes to making a net improvement in its dynamic behaviour. This leads in turn to significantly higher quality of the milled surface. The article presents a method to apply balancing of the transversal cutting force to two types of machining passes and elaborates an associated strategy to plan cutter paths enabling an improvement in surface quality to be achieved.

Keywords

Five-axis milling Machining strategy Balance of the transversal cutting force Complex-shaped workpiece 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Kruth JP, Klewais P (1994) Optimization and dynamic adaptation of the cutter inclination during five-axis milling of sculptured surfaces. Ann CIRP 43(1):443–448CrossRefGoogle Scholar
  2. 2.
    Jensen CG, Red WE, Pi J (2002) Tool selection for five-axis curvature matched machining. Comput Aided Des 34(3):251–266CrossRefGoogle Scholar
  3. 3.
    Krzysztof M (1987) Influence of surface shape on admissible tool positions in 5-axis face milling. Comput Aided Des 19(5):233–236CrossRefMATHGoogle Scholar
  4. 4.
    Chen T, Ye P, Wang J (2005) Local interference detection and avoidance in five-axis NC machining of sculptured surfaces. Int J Adv Manuf Technol 25(3–4):343–349CrossRefGoogle Scholar
  5. 5.
    Yuan-Shin L (1997) Admissible tool orientation control of gouging avoidance for 5-axis complex surface machining. Comput Aided Des 29(7):507–521CrossRefGoogle Scholar
  6. 6.
    Jianhua F, Alan B (2008) Quadric method for cutter orientation in five-axis sculptured surface machining. Int J Mach Tool Manuf 48(7–8):788–801Google Scholar
  7. 7.
    Warkentin A, Ismail F, Bedi S (2000) Multi-point tool positioning strategy for 5-axis machining of sculptured surfaces. Comput Aided Geom Des 17(1):83–100CrossRefMathSciNetGoogle Scholar
  8. 8.
    Gray PJ, Bedi S, Ismail F (2005) Arc-intersect method for 5-axis tool positioning. Comput Aided Des 37(7):663–674CrossRefGoogle Scholar
  9. 9.
    Rubio W (1993) Génération de trajectoires du centre de l’outil pour l’usinage de surfaces complexes sur machines à trois et cinq axes. Thèse de doctorat, Université Paul Sabatier, Toulouse IIIGoogle Scholar
  10. 10.
    Patrick G, Frederic M, Walter R (2006) Modelling cutting forces in milling on torus cutters. Int J Mach Mach Mater 1:166–185, N°2Google Scholar
  11. 11.
    Gilles P, Monies F, Rubio W (2007) Optimum orientation of a torus milling cutter: method to balance the transversal cutting force. Int J Mach Tool Manuf 47(15):2263–2272CrossRefGoogle Scholar
  12. 12.
    Gilles P, Cohen G, Monies F, Rubio W (2009) Dynamic behaviour improvement for a torus milling cutter using balance of the transversal cutting force. Int J Adv Manuf Technol 40(7–8):669–675CrossRefGoogle Scholar
  13. 13.
    Gilles P, Cohen G, Monies F, Rubio W (2013) Torus cutter positioning in five-axis milling using balance of the transversal cutting force. Int J Adv Manuf Technol 66(5–8):965–973CrossRefGoogle Scholar
  14. 14.
    Redonnet J-M, Rubio W, Monies F, Dessein G (2000) Optimising tool positioning for end-mill machining of free-form surfaces on 5-axis machines for both semi-finishing and finishing. Int J Adv Manuf Technol 16(6):383–391CrossRefGoogle Scholar
  15. 15.
    Monies F, Mousseigne M, Redonnet J-M, Rubio W (2004) Determining a collision-free domain for the tool in five axis machining. Int J Prod Res 42(21):4513–4530CrossRefMATHGoogle Scholar
  16. 16.
    Gilles P, Senatore J, Segonds S, Monies F, Rubio W (2012) Determination of angular fields outside low and high collisions to mill free-form surfaces on 5-axis CNC machines. Int J Prod Res 50(4):1045–1061CrossRefGoogle Scholar
  17. 17.
    Chiou C-J, Lee Y-S (1999) A shape-generating approach for multi-axis machining G-buffer models. Comput Aided Des 31(12):761–776CrossRefMATHGoogle Scholar

Copyright information

© Springer-Verlag London 2014

Authors and Affiliations

  • Patrick Gilles
    • 1
  • Guillaume Cohen
    • 1
  • Frederic Monies
    • 1
  • Walter Rubio
    • 1
  1. 1.Institut Clément AderToulouse cedex 4France

Personalised recommendations