Advertisement

Analysis of acoustic emission emerging during hydroabrasive cutting and options for indirect quality control

  • Sergej Hloch
  • Jan Valíček
  • Dražan Kozak
  • Hakan Tozan
  • Somnath Chattopadhyaya
  • Pavel Adamčík
ORIGINAL ARTICLE

Abstract

The paper discusses connections of acoustic emission in abrasive water jet cutting. Introduction focuses on theoretical knowledge on this technology and offers analysis related to current state of the art of the problem research. Further description of performed experiments is presented in case in which acoustic emission behaviour was observed with the exactly scheduled change of cutting conditions or rather cutting head traverse speed v. The beginning of the initial part contains FFT spectral analyses and comparison of the examined sections of the experimental samples. Consequently a graphical representation and comparison of peak-to-peak values (maximal amplitudes) and values of AERMS at the time of experimental cutting follow. At the close of the work, the analyses are expressed as dependence on the cutting head traverse speed v with expressed regulation equations applicable in the close-loop control process with minimum human intervention and in case of fault conditions—broken focusing tube, fractured water nozzle.

Keywords

Abrasive water jet cutting Acoustic emission Traverse speed 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Abdel-Rahman AA, El-Domiaty AA (1998) Maximum depth of cut for ceramics using abrasive waterjet technique. Wear 218:216–222CrossRefGoogle Scholar
  2. 2.
    Akkurt A, Kulecki MK, Seker U, Ercan F (2004) Effect of feed rate on surface roughness in abrasive waterjet cutting applications. J Mater Process Technol 147:389–396CrossRefGoogle Scholar
  3. 3.
    Arola D, Ramulu M (1997) Material removal in abrasive waterjet machining of metals a residual stress analysis. Wear 211:302–310CrossRefGoogle Scholar
  4. 4.
    Axinte DA, Kong MC (2009) An integrated monitoring method to supervise waterjet machining. CIRP Ann Manuf Technol 58:303–306CrossRefGoogle Scholar
  5. 5.
    Aydin G, Karakurt I, Aydiner K (2011) An investigation on surface roughness of granite machined by abrasive waterjet. Bull Mater Sci 34:985–992CrossRefGoogle Scholar
  6. 6.
    Benardos PG, Vosniakos GC (2003) Predicting surface roughness in machining: a review. Int J Mach Tool Manuf 43:833–844CrossRefGoogle Scholar
  7. 7.
    Caydas U, Hascalik A (2008) A study on surface roughness in abrasive waterjet machining process using artificial neural networks and regression analysis method. J Mater Process Technol 202:574–582CrossRefGoogle Scholar
  8. 8.
    Chao J, Geskin E (1993) Experimental study of the striation formation and spectral analysis of the abrasive waterjet generated surfaces. In: Proceedings of the Seventh American Water Jet Conference, Seattle, Washington, 27–41Google Scholar
  9. 9.
    Chen FL, Wang J, Lemma E, Siores E (2003) The mechanisms of surface striation formation in abrasive waterjet machining. J Mater Process Technol 141:213–218CrossRefGoogle Scholar
  10. 10.
    Deam RT, Lemma E, Ahmed DH (2004) Modelling of the abrasive water jet cutting. Wear 257:877–981CrossRefGoogle Scholar
  11. 11.
    Delijaicov S et al (2010) Improved model to predict machined surface roughness based on the cutting vibrations signal during hard turning. Arch Mater Sci Eng 45:102–107Google Scholar
  12. 12.
    El-Domiaty A, Abdel-Rahman A (1997) Fracture mechanics-based model of abrasive waterjet cutting for brittle materials. J Adv Manuf Technol 13:171–181CrossRefGoogle Scholar
  13. 13.
    Foldyna J, Sitek L, Scucka J et al (2009) Effects of pulsating water jet impact on aluminium surface. J Mater Process Technol 209:6174–6180CrossRefGoogle Scholar
  14. 14.
    Foldyna J, Sitek L, Svehla B et al (2004) Utilization of ultrasound to enhance high-speed water jet effects. Ultrason Sonochemistry 11:131–137CrossRefGoogle Scholar
  15. 15.
    Fowler G, Shipway PH, Pashby IR (2005) Abrasive water-jet controlled depth milling of Ti6A14V alloy—an investigation of the role of jet—workpiece traverse speed and abrasive grit size on the characteristics of the milled material. J Mater Process Tech 161:407–414CrossRefGoogle Scholar
  16. 16.
    Hascalik A, Caydas U, Gurun H (2007) Effect of traverse speed on abrasive waterjet machining of Ti-6Al-4V alloy. Mater Des 28:1953–1957CrossRefGoogle Scholar
  17. 17.
    Hassan AI, Chen C, Kovacevic R (2004) On-line monitoring of depth of cut in AWJ cutting. Int J Mach Tool Manuf 44:595–605CrossRefGoogle Scholar
  18. 18.
    Hlavac LM (2009) Investigation of the abrasive water jet trajectory curvature inside the kerf. J Mater Process Technol 209:4154–4161CrossRefGoogle Scholar
  19. 19.
    Hloch S, Tozan H, Yagimli M et al (2011) Using waterjet in reverse logistic operations in discarded munitions processing. Tehnicki vjesnik-Technical Gaz 18:267–271Google Scholar
  20. 20.
    Hloch S, Valíček J (2011) Prediction of distribution relationship of titanium surface topography created by abrasive waterjet. Int J Surf Sci Eng 5:152–168CrossRefGoogle Scholar
  21. 21.
    Hloch S, Valíček J, Hreha P, Bednár S et al. On-line identification of hydroabrasive cutting by means of acoustic emission and vibration. Steevepress Ltd., Prešov, p. 126Google Scholar
  22. 22.
    Hloch S et al (2008) Experimental study of surface topography created by abrasive waterjet cutting. Strojarstvo 49:303–309Google Scholar
  23. 23.
    Hreha P, Hloch S, Valíček J et al (2010) Impact of abrasive mass flow rate when penetrating into a material on its vibration. Tehnicki vjesnik-Technical Gaz 17:475–480Google Scholar
  24. 24.
    Jurisevic B, Brissaud D, Junkar M (2004) Monitoring of abrasive water jet (AWJ) cutting using sound detection. Int J Adv Manuf Technol 24:733–737CrossRefGoogle Scholar
  25. 25.
    Kök M, Kanca E, Eyercioğlu Ö (2011) Prediction of surface roughness in abrasive waterjet machining of particle reinforced MMCs using genetic expression programming. Int J Adv Manuf Technol 55:955–968CrossRefGoogle Scholar
  26. 26.
    Kulecki KM (2002) Processes and apparatus developments in industrial waterjet applications. Ind J Mach Tools Manuf 42:1297–1306CrossRefGoogle Scholar
  27. 27.
    Hlavacek P et al (2009) Measurement of fine copper surface texture created by abrasive waterjet cutting. Strojarstvo 51:273–279Google Scholar
  28. 28.
    Kusnerova M et al (2008) Derivation and measurement of the velocity parameters of hydrodynamics oscillating system. Strojarstvo 50:375–379Google Scholar
  29. 29.
    Kusnerova M et al (2011) Determination of technologically optimal factors of modulated waterjet. Int J Adv Manuf Technol. doi: 10.1007/s00170-011-3602-1
  30. 30.
    Lebar A, Junkar M (2004) Simulation of abrasive water jet cutting process: part 1. Unit event approach. Model Simul Mater Sci Eng 12:1159–1170CrossRefGoogle Scholar
  31. 31.
    Lu C (2008) Study on prediction of surface quality in machining process. J Mater Process Technol 205:439–450CrossRefGoogle Scholar
  32. 32.
    Ma C, Deam RT (2006) A correlation for predicting the kerf profile from abrasive water jet cutting. Exp Therm Fluid Sci 30:337–343CrossRefGoogle Scholar
  33. 33.
    Marinescu I, Axinte DA (2008) A critical analysis of effectiveness of acoustic emission signals to detect tool and workpiece malfunctions in milling operations. Int J Mach Tool Manuf 48:1148–1160CrossRefGoogle Scholar
  34. 34.
    Modrak V, Paško J, Pavlenko S (2002) Alternative solution for a robotic stereotactic system. J Intell Robot Syst 35:193–202zbMATHCrossRefGoogle Scholar
  35. 35.
    Momber WA, Kovacevic R (1998) Principles of abrasive water jet machining. Springer-Verlag, Berlin, p 394zbMATHCrossRefGoogle Scholar
  36. 36.
    Monkova K et al (2011) Factor analysis of the abrasive waterjet factors affecting the surface roughness of titanium. Tehnicki vjesnik-Technical Gaz 18:73–77Google Scholar
  37. 37.
    Nanduri M, Taggart DG, Kim TJ (2002) The effects of system and geometric parameters on abrasive water jet nozzle wear. Int J Mach Tool Manuf 42:616–623CrossRefGoogle Scholar
  38. 38.
    Palleda M (2007) A study of taper angles and material removal rates of drilled holes in the abrasive water jet machining process. J Mater Process Technol 189:292–295CrossRefGoogle Scholar
  39. 39.
    Radvanska A (2010) Abrasive waterjet cutting technology risk assessment by means of failure modes and effects analysis method. Tehnicki vjesnik-Technical Gaz 17:121–128Google Scholar
  40. 40.
    Radzevich SP, Kreheľ R (2011) Application priority mathematical model of operating parameters in advanced manufacturing technology. Int J Adv Manuf Technol 56:835–840CrossRefGoogle Scholar
  41. 41.
    Rui-Hong W, Ke-Feng C, De-You L, An-Chang M (2009) Research of ultra-fine communicating coal with premixed water jet based on neural network. Procedia Earth and Planetary Science 1:1519–1524CrossRefGoogle Scholar
  42. 42.
    Salak A, Vasilko K, Selecka M et al (2006) New short time face turning method for testing the machinability of PM steels. J Mater Process Technol 176:62–69CrossRefGoogle Scholar
  43. 43.
    Schetz JA, Fuhs AE (1996) Nozzle flow. In: Schetz JA, Fuhs AE (eds) Handbook of fluid dynamics and fluid machinery, vol 1. Wiley, New York, pp 609–615Google Scholar
  44. 44.
    Sharma V, Kumar S (2005) A study of process parameters for coal cutting under Indian environmental condition using hydro jet cutting system. Int J Manuf Tech Manag 7:391–403Google Scholar
  45. 45.
    Sharma V et al (2011) Multi response optimization of process parameters based on Taguchi-Fuzzy model for coal cutting by water jet technology. Int J Adv Manuf Technol 56:1019–1025CrossRefGoogle Scholar
  46. 46.
    Srinivasu DS, Ramesh Babu N (2008) A neuro-genetic approach for selection of process parameters in abrasive waterjet cutting considering variation in diameter of focusing nozzle. Appl Soft Comput 8:809–819CrossRefGoogle Scholar
  47. 47.
    Tonkshoff HK, Jung M, Mannel S, Rietz W (2000) Using acoustic emission signals for monitoring of production process. Ultrasonics 37:681–686CrossRefGoogle Scholar
  48. 48.
    Tozan H (2011) Fuzzy ahp based decision support system for technology selection in abrasive water jet cutting processes. Tehnicki vjesnik-Technical Gaz 18:187–191Google Scholar
  49. 49.
    Valíček J et al (2007) Study of surfaces generated by abrasive waterjet technology. In: Sobh T et al (eds) Innovative algorithms and techniques in automation, industrial electronics and telecommunications.. doi: 10.1007/978-1-4020-6266-7_34 Google Scholar
  50. 50.
    Valíček J, Držík M, Hloch S et al (2007) Experimental analysis of irregularities of metallic surfaces generated by abrasive waterjet. Int J Mach Manuf 47:1786–1790CrossRefGoogle Scholar
  51. 51.
    Valíček J, Hloch S (2009) Optical measurement of surface and topographical parameters investigation created by abrasive waterjet. Int J Surf Sci Eng 3:360–373CrossRefGoogle Scholar
  52. 52.
    Valíček J, Hloch S (2010) Using the acoustic sound pressure level for quality prediction of surfaces created by abrasive waterjet. Int J Adv Manuf Technol 48:193–203CrossRefGoogle Scholar
  53. 53.
    Valíček J, Hloch S, Kozak D (2009) Surface geometric parameters proposal for the advanced control of abrasive waterjet technology. Int J Adv Manuf Technol 41:323–328CrossRefGoogle Scholar
  54. 54.
    Vasilko K, Novák-Marcinčin J, Havrila M (2003) Manufacturing engineering. TUKE, Prešov, 424Google Scholar
  55. 55.
    Wang J (1999) Abrasive waterjet machining of polymer matrix composites—cutting performance, erosive process and predictive models. Int J Adv Manuf Technol 15:757–768CrossRefGoogle Scholar
  56. 56.
    Wang J, Guo DM (2002) A predictive depth of penetration model for abrasive waterjet cutting of polymer matrix composites. J Mater Process Technol 121:390–394CrossRefGoogle Scholar
  57. 57.
    Xu J, You B, Kong X (2008) Design and experiment research on abrasive water-jet cutting machine based on phased intensifier. In: 2008 IFAC: Proceedings of the 17th world congress. The International Federation of Automatic Control, 6–11 July 2008, Seoul, p 14846–1485Google Scholar
  58. 58.
    Yanaida K (1974) Flow characteristics of water jets symposium on jet cutting paper no A2Google Scholar
  59. 59.
    Yanaida K, Ohashi A (1980) Flow characteristics of water jet in air. In: Proceeding of 5th International Symposium on Jet Cutting Technology, A3:33–44Google Scholar
  60. 60.
    Zain AZ, Haron H, Sharif S (2011) Genetic algorithm and simulated annealing to estimate optimal process parameters of the abrasive waterjet machining. Eng Comput 27:251–259CrossRefGoogle Scholar
  61. 61.
    Zhou G (1993) Statistical, random and fractal characterizations of surface topography with engineering applications. Dissertation. New Jersey: New Jersey Institute of Technology, Department of Mechanical and Industrial Engineering, 1–43Google Scholar

Copyright information

© Springer-Verlag London Limited 2012

Authors and Affiliations

  • Sergej Hloch
    • 1
  • Jan Valíček
    • 2
  • Dražan Kozak
    • 3
  • Hakan Tozan
    • 4
  • Somnath Chattopadhyaya
    • 5
  • Pavel Adamčík
    • 6
  1. 1.Faculty of Manufacturing TechnologiesTechnical University of Košice with a seat in PrešovPrešovSlovakia
  2. 2.Institute of Physics, Faculty of Mining and GeologyTechnical University of OstravaOstrava-PorubaCzech Republic
  3. 3.Mechanical Engineering Faculty in Slavonski BrodJ J Strossmayer University of OsijekSlavonski BrodCroatia
  4. 4.Turkish Naval Academy Department of Industrial EngineeringIstanbulTurkey
  5. 5.Department of ME & MMEIndian School of MinesDhanbadIndia
  6. 6.Technická Diagnostika, LtdPrešovSlovak Republic

Personalised recommendations