Advertisement

Topology optimization of continuum structures for the uniformity of contact pressures

  • Cao Niu
  • Weihong ZhangEmail author
  • Tong Gao
Research Paper

Abstract

In this paper, a topology optimization method is developed for elastic continuum structures in frictionless contact to improve the uniformity of contact pressures. The variance constraint of contact pressures is introduced into the standard volume-constrained compliance minimization problem and combined with the three-field SIMP (Solid Isotropic Material with Penalization) model. Two geometric constraints are also incorporated to achieve optimization solutions with desired minimum length scales and clear boundaries without intermediate densities. To ensure a correct evaluation of contact pressure variance, a density threshold method is proposed to assign each contact node pair a certain density value according to the physical densities of its adjacent elements and further to exclude the contact node pairs with density values smaller than the threshold value. The effectiveness of the proposed method is validated through a series of numerical examples including elastic-rigid and elastic-elastic frictionless contact problems. The influence of the variance constraint of contact pressures on the optimization result is discussed in comparison with the standard maximum stiffness design. It concludes that the variance of contact pressures can be reduced at the cost of the structural stiffness, which implies that a trade-off exists between the structural stiffness and the uniformity of contact pressures.

Keywords

Topology optimization Frictionless contact Contact pressure Uniformity Variance 

Notes

Acknowledgements

This work is supported by National Key Research and Development Program of China (2017YFB1102800), National Natural Science Foundation of China (11620101002, 11432011), and Key Research and Development Program of Shaanxi (2017KW-ZD-11).

References

  1. Aage N, Andreassen E, Lazarov BS, Sigmund O (2017) Giga-voxel computational morphogenesis for structural design. Nature 550:84–86CrossRefGoogle Scholar
  2. Archard JF (1953) Contact and rubbing of flat surfaces. J Appl Phys 24:981–988CrossRefGoogle Scholar
  3. Bendsøe MP, Kikuchi N (1988) Generating optimal topologies in structural design using a homogenization method. Comput Methods Appl Mech Eng 71:197–224MathSciNetCrossRefzbMATHGoogle Scholar
  4. Bendsøe MP, Sigmund O (2004) Topology optimization: theory, methods and applications, 2nd edn. Springer, BerlinCrossRefzbMATHGoogle Scholar
  5. Benedict RL (1982) Maximum stiffness design for elastic bodies in contact. J Mech Des 104:825–830CrossRefGoogle Scholar
  6. Bruggi M, Duysinx P (2013) A stress–based approach to the optimal design of structures with unilateral behavior of material or supports. Struct Multidiscip Optim 48:311–326MathSciNetCrossRefGoogle Scholar
  7. Budynas RG, Nisbett JK (2010) Shigley’s mechanical engineering design, 9th edn. McGraw-Hill, New YorkGoogle Scholar
  8. Clausen A, Andreassen E (2017) On filter boundary conditions in topology optimization. Struct Multidiscip Optim 56:1147–1155MathSciNetCrossRefGoogle Scholar
  9. Collins JA, Busby HR, Staab GH (2010) Mechanical design of machine elements and machines: a failure prevention perspective, 2nd edn. John Wiley & Sons, HobokenGoogle Scholar
  10. Deaton JD, Grandhi RV (2014) A survey of structural and multidisciplinary continuum topology optimization: post 2000. Struct Multidiscip Optim 49:1–38MathSciNetCrossRefGoogle Scholar
  11. Desmorat B (2007) Structural rigidity optimization with frictionless unilateral contact. Int J Solids Struct 44:1132–1144MathSciNetCrossRefzbMATHGoogle Scholar
  12. Fancello EA (2006) Topology optimization for minimum mass design considering local failure constraints and contact boundary conditions. Struct Multidiscip Optim 32:229–240MathSciNetCrossRefzbMATHGoogle Scholar
  13. Faustini MC, Crawford RH, Neptune RR, Rogers WE, Bosker G (2005) Design and analysis of orthogonally compliant features for local contact pressure relief in transtibial prostheses. J Biomech Eng 127:946–951CrossRefGoogle Scholar
  14. Gao T, Xu PL, Zhang WH (2016) Topology optimization of thermo-elastic structures with multiple materials under mass constraint. Comput Struct 173:150–160CrossRefGoogle Scholar
  15. Gao T, Qiu LB, Zhang WH (2017) Topology optimization of continuum structures subjected to the variance constraint of reaction forces. Struct Multidiscip Optim 56:755–765MathSciNetCrossRefGoogle Scholar
  16. Hilding D, Klarbring A, Petersson J (1999) Optimization of structures in unilateral contact. Appl Mech Rev 52:139–160CrossRefGoogle Scholar
  17. Hills DA (1994) Mechanics of fretting fatigue. Wear 175:107–113CrossRefGoogle Scholar
  18. Ignesti M, Innocenti A, Marini L, Meli E, Rindi A, Toni P (2013) Wheel profile optimization on railway vehicles from the wear viewpoint. Int J Non-Linear Mech 53:41–54CrossRefGoogle Scholar
  19. Jeong G-E, Youn S-K, Park KC (2018) Topology optimization of deformable bodies with dissimilar interfaces. Comput Struct 198:1–11CrossRefGoogle Scholar
  20. Kikuchi N, Oden JT (1988) Contact problems in elasticity: a study of variational inequalities and finite element methods. Society for Industrial and Applied Mathematics, PhiladelphiaCrossRefzbMATHGoogle Scholar
  21. Klarbring A, Haslinger J (1993) On almost constant contact stress distributions by shape optimization. Struct Optim 5:213–216CrossRefGoogle Scholar
  22. Klarbring A, Petersson J, Rönnqvist M (1995) Truss topology optimization including unilateral contact. J Optim Theory Appl 87:1–31MathSciNetCrossRefzbMATHGoogle Scholar
  23. Lawry M, Maute K (2015) Level set topology optimization of problems with sliding contact interfaces. Struct Multidiscip Optim 52:1107–1119MathSciNetCrossRefGoogle Scholar
  24. Lawry M, Maute K (2018) Level set shape and topology optimization of finite strain bilateral contact problems. Int J Numer Methods Eng 113:1340–1369MathSciNetCrossRefGoogle Scholar
  25. Lazarov BS, Wang F, Sigmund O (2016) Length scale and manufacturability in density-based topology optimization. Arch Appl Mech 86:189–218CrossRefGoogle Scholar
  26. Li L, Khandelwal K (2015) Volume preserving projection filters and continuation methods in topology optimization. Eng Struct 85:144–161CrossRefGoogle Scholar
  27. Li W, Li Q, Steven GP, Xie YM (2005) An evolutionary shape optimization for elastic contact problems subject to multiple load cases. Comput Methods Appl Mech Eng 194:3394–3415CrossRefzbMATHGoogle Scholar
  28. Liu P, Kang Z (2018) Integrated topology optimization of multi-component structures considering connecting interface behavior. Comput Methods Appl Mech Eng 341:851–887MathSciNetCrossRefGoogle Scholar
  29. Liu P, Luo Y, Kang Z (2016) Multi-material topology optimization considering interface behavior via XFEM and level set method. Comput Methods Appl Mech Eng 308:113–133MathSciNetCrossRefGoogle Scholar
  30. Lopes CG, dos Santos RB, Novotny AA, Sokolowski J (2017) Asymptotic analysis of variational inequalities with applications to optimum design in elasticity. Asymptot Anal 102:227–242MathSciNetCrossRefzbMATHGoogle Scholar
  31. Luo YJ, Li M, Kang Z (2016) Topology optimization of hyperelastic structures with frictionless contact supports. Int J Solids Struct 81:373–382CrossRefGoogle Scholar
  32. Mak AFT, Zhang M, Boone DA (2001) State-of-the-art research in lower-limb prosthetic biomechanics-socket interface: a review. J Rehabil Res Dev 38:161–173Google Scholar
  33. Mankame ND, Ananthasuresh GK (2004) Topology optimization for synthesis of contact-aided compliant mechanisms using regularized contact modeling. Comput Struct 82:1267–1290CrossRefGoogle Scholar
  34. Myśliński A (2015) Piecewise constant level set method for topology optimization of unilateral contact problems. Adv Eng Softw 80:25–32CrossRefGoogle Scholar
  35. Myśliński A, Wróblewski M (2017) Structural optimization of contact problems using Cahn–Hilliard model. Comput Struct 180:52–59CrossRefGoogle Scholar
  36. Nour-Omid B, Wriggers P (1987) A note on the optimum choice for penalty parameters. Commun Appl Num Methods 3:581–585CrossRefzbMATHGoogle Scholar
  37. Pedersen NL (2016) On optimization of interference fit assembly. Struct Multidiscip Optim 54:349–359MathSciNetCrossRefGoogle Scholar
  38. Petersson J, Patriksson M (1997) Topology optimization of sheets in contact by a subgradient method. Int J Numer Methods Eng 40:1295–1321MathSciNetCrossRefzbMATHGoogle Scholar
  39. Qian XP, Sigmund O (2013) Topological design of electromechanical actuators with robustness toward over- and under-etching. Comput Methods Appl Mech Eng 253:237–251MathSciNetCrossRefzbMATHGoogle Scholar
  40. Ruiz C, Nowell D (2000) Designing against fretting fatigue in aeroengines. In: Fuentes M, Elices M, Martín-Meizoso A, Martínez-Esnaola JM (eds) Fracture mechanics: applications and challenges, vol 26. Elsevier, San Sebastian, pp 73–95Google Scholar
  41. Sigmund O (2007) Morphology-based black and white filters for topology optimization. Struct Multidiscip Optim 33:401–424CrossRefGoogle Scholar
  42. Sigmund O, Maute K (2013) Topology optimization approaches a comparative review. Struct Multidiscip Optim 48:1031–1055MathSciNetCrossRefGoogle Scholar
  43. Sigmund O, Petersson J (1998) Numerical instabilities in topology optimization: a survey on procedures dealing with checkerboards, mesh-dependencies and local minima. Struct Optim 16:68–75CrossRefGoogle Scholar
  44. Strömberg N (2010a) Topology optimization of structures with manufacturing and unilateral contact constraints by minimizing an adjustable compliance–volume product. Struct Multidiscip Optim 42:341–350MathSciNetCrossRefzbMATHGoogle Scholar
  45. Strömberg N (2010b) Topology optimization of two linear elastic bodies in unilateral contact. Paper presented at the 2nd International Conference on Engineering Optimization, Lisbon, Portugal, September 6–9, 2010Google Scholar
  46. Strömberg N (2012) Topology optimisation of bodies in unilateral contact by maximizing the potential energy. Paper presented at the Eleventh International Conference on Computational Structures Technology, Dubrovnik, Croatia, 4–7 September, 2012Google Scholar
  47. Strömberg N (2013) The influence of sliding friction on optimal topologies. In: Stavroulakis GE (ed) Recent advances in contact mechanics: papers collected at the 5th Contact Mechanics International Symposium (CMIS2009), April 28–30, 2009, Chania, Greece. Springer Berlin Heidelberg, Berlin, Heidelberg, pp 327–336CrossRefGoogle Scholar
  48. Strömberg N (2018) Topology optimization of orthotropic elastic design domains with mortar contact conditions. In: Schumacher A, Vietor T, Fiebig S, Bletzinger K-U, Maute K (eds) Advances in structural and multidisciplinary optimization: proceedings of the 12th World Congress of Structural and Multidisciplinary Optimization. Springer International Publishing, Braunschweig, pp 1427–1438CrossRefGoogle Scholar
  49. Strömberg N, Klarbring A (2010) Topology optimization of structures in unilateral contact. Struct Multidiscip Optim 41:57–64MathSciNetCrossRefzbMATHGoogle Scholar
  50. Stupkiewicz S (2001) Extension of the node-to-segment contact element for surface-expansion-dependent contact laws. Int J Numer Methods Eng 50:739–759CrossRefzbMATHGoogle Scholar
  51. Svanberg K (1995) A globally convergent version of MMA without linesearch. In: Proceedings of the first world congress of structural and multidisciplinary optimization, Goslar, Germany, 1995. pp 9–16Google Scholar
  52. Sylves K, Maute K, Dunn ML (2009) Adhesive surface design using topology optimization. Struct Multidiscip Optim 38:455–468CrossRefGoogle Scholar
  53. Wang F, Lazarov BS, Sigmund O (2011) On projection methods, convergence and robust formulations in topology optimization. Struct Multidiscip Optim 43:767–784CrossRefzbMATHGoogle Scholar
  54. Waterhouse RB (1984) Fretting wear. Wear 100:107–118CrossRefGoogle Scholar
  55. Waterhouse RB (1992) Fretting fatigue. Int Mater Rev 37:77–98CrossRefGoogle Scholar
  56. Wriggers P (2006) Computational contact mechanics, 2nd edn. Springer, BerlinCrossRefzbMATHGoogle Scholar
  57. Xu SL, Cai YW, Cheng GD (2010) Volume preserving nonlinear density filter based on heaviside functions. Struct Multidiscip Optim 41:495–505MathSciNetCrossRefzbMATHGoogle Scholar
  58. Zhang WH, Niu C (2018) A linear relaxation model for shape optimization of constrained contact force problem. Comput Struct 200:53–67CrossRefGoogle Scholar
  59. Zhang WH, Xia L, Zhu JH, Zhang Q (2011) Some recent advances in the integrated layout design of multicomponent systems. J Mech Des 133:104503–104515CrossRefGoogle Scholar
  60. Zhang JX, Wang B, Niu F, Cheng GD (2015) Design optimization of connection section for concentrated force diffusion. Mech Based Des Struct Mach 43:209–231CrossRefGoogle Scholar
  61. Zhou MD, Lazarov BS, Wang FW, Sigmund O (2015) Minimum length scale in topology optimization by geometric constraints. Comput Methods Appl Mech Eng 293:266–282MathSciNetCrossRefGoogle Scholar
  62. Zhou Y, Zhang WH, Zhu JH, Xu Z (2016) Feature-driven topology optimization method with signed distance function. Comput Methods Appl Mech Eng 310:1–32MathSciNetCrossRefGoogle Scholar
  63. Zhu JH, Li Y, Zhang WH, Hou J (2016a) Shape preserving design with structural topology optimization. Struct Multidiscip Optim 53:893–906MathSciNetCrossRefGoogle Scholar
  64. Zhu JH, Zhang WH, Xia L (2016b) Topology optimization in aircraft and aerospace structures design. Arch Comput Methods Eng:595–622Google Scholar
  65. Zienkiewicz OC, Taylor RL, Fox DD (2014) The finite element method for solid and structural mechanics, 7th edn. Butterworth-Heinemann, OxfordzbMATHGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  1. 1.State IJR Center of Aerospace Design and Additive Manufacturing, School of Mechanical EngineeringNorthwestern Polytechnical UniversityXi’anChina

Personalised recommendations