Advertisement

Interceram - International Ceramic Review

, Volume 64, Issue 3, pp 108–111 | Cite as

Effect of Nano Metallic Fe on Al5O6N Synthesis in Al2O3-C Refractories

  • Xiumin Tan
  • Zhang Zhao
  • Pingan Chen
  • Xiangcheng Li
  • Boquan Zhu
Special Technologies

Abstract

Al2O3-C refractory samples were prepared using corundum, flake graphite, Al and Si powders and phenolic resin as raw materials. The in-situ synthesis mechanism of Al5O6N in Al2O3-C refractories was studied and the effect of adding nano metallic Fe on the formation and microstructure of Al5O6N phase was also investigated. Thermodynamic calculations show that Al5O6N can potentially be synthesized in a reducing atmosphere at 1600°C over a narrow range of N2 and CO pressures. Experimental results proved that Al5O6N phase was synthesized after 1600°C heat treatment when nano Fe was added to Al2O3-C refractories. As the content of nano Fe increases, Al5O6N particles show disappearance of oriented growth, with octahedron shapes turning into spherical agglomerations.

Keywords

Al2O3-C refractories Al5O6synthesis mechanism 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    Yamaguchi, A.: The carbon composite refractory. Refractories 28 (1994) 128–132Google Scholar
  2. [2]
    Li, X.C., Zhu, B.Q., Zhao, F.: In-situ synthesis of SiC and β-Si3Al3O3N5 whiskers in alumina carbon based materials. Mater. Sci. Forum 745–746 (2013) 663–665CrossRefGoogle Scholar
  3. [3]
    Li, X.C., Li, Y.X., Zhu, B.Q.: Matrix structure evolution and thermo-mechanical properties of carbon fiber-reinforced Al2O3-SiC-C castable composites. Mater. Res. Bull. 61 (2014) 201–206CrossRefGoogle Scholar
  4. [4]
    Zhu, B.Q., Zhu, Y.N., Li, X.C., et al.: Effect of ceramic bonding phases on the thermo-mechanical properties of Al2O3-C refractories. Ceram. Int. 39 (2013) 6069–6076CrossRefGoogle Scholar
  5. [5]
    Antsiferov, V.N., Gilyov, V.G., Karmanov, V.I.: IR-spectra and phases structure of sialons. Vibr. Spectros. 30 (2002) 169–173CrossRefGoogle Scholar
  6. [6]
    Willems, H.X., Hendrix, M.R., Metselaar, R., et al.: Strength and microstructure of silicon nitride/aluminum interface fabricated by squeeze cast brazing. J. Eur. Ceram. Soc. 12 (1993) 43–49CrossRefGoogle Scholar
  7. [7]
    Wang, Z.S., Liu, J.X., Li, F.S.: The fabrication and characterization of Al5O6N nano powders. J. Chin. Ceram. Soc. 36 (2008) 580–583Google Scholar
  8. [8]
    Wei, G.P., Zhu, B.Q., Li, X.C., et al.: Microstructure and mechanical properties of low-carbon MgO-C refractories bonded by an Fe nanosheet-modified phenol resin. Ceram. Int. 41 (2015) 1553–1566CrossRefGoogle Scholar
  9. [9]
    McCauley, J.W., Corbin, N.D.: High Temperature reactions and microstructures in the Al2O3-AlN System. Progress in Nitrogen Ceramics 65 (1983) 111–118CrossRefGoogle Scholar

Copyright information

© Springer Fachmedien Wiesbaden 2015

Authors and Affiliations

  • Xiumin Tan
    • 1
  • Zhang Zhao
    • 2
  • Pingan Chen
    • 2
  • Xiangcheng Li
    • 2
  • Boquan Zhu
    • 2
  1. 1.China National Engineering Research Center for Utilization of Industrial MineralsZhengzhouChina
  2. 2.The Key State Laboratory of Refractories and MetallurgyWuhan University of Science and TechnologyWuhanChina

Personalised recommendations