Abstract
The influence of the cutting conditions on the surface roughness Ra is compared for components produced by additive technology with structure parallel and perpendicular to the axis of rotation. The internal structure has a considerable influence on the quality of the machined surface.
Similar content being viewed by others
REFERENCES
Abbasov, A.E., Systemic research and forecasting using rapid prototyping technology, Inf.-Tekhnol. Vestn., 2015, no. 3 (5), pp. 3–14.
Aleksandrov, V.V., Aleksandrova, V.V., Zaitseva, A.A., and Khurs, S.P., Industrial 3D digital technology, Tr. S.-Peterb. Inst. Inf. Avtom., Ross. Akad. Nauk, 2010, no. 4 (15), pp. 85–92.
Litunov, S.N., Slobodnyuk, V.S., Mel’nikov, D.V., Review and analysis of additive technologies, Part 1, Omsk. Nauchn. Vestn., 2016, no. 1 (145), pp. 12–17.
Litunov, S.N., Slobodnyuk, V.S., Mel’nikov, D.V., et al., Review and analysis of additive technologies, Part 2, Omsk. Nauchn. Vestn., 2016, no. 5 (149), pp. 2–24.
Chemodurov, A.N., Application of additive technologies for the manufactoring of mechanical engineering products, Izv. Tul’sk. Gos. Univ., Tekh. Nauki, 2016, no. 8-2, pp. 210–216.
Muratov, K.R., Gashev, E.A., Ablyaz, T.R., et al., Influence of cutting conditions on the surface roughness of titanium-alloy parts produced by additive and traditional methods, Russ. Eng. Res., 2021, vol. 41, no. 5, pp. 434–436.
Rebrova, I.A., Planirovanie eksperimenta: Uchebnoe posobie (Experiment Planning: Manual), Omsk: Sib. Avtom.-Dorozhn. Inst., 2010
Petkov, A.A., Ortogonal’noe tsentral’noe kompozitsionnoe planirovanie v tekhnike i elektrofizike vysokikh napryazhenii: Uchebno-metodicheskoe posobie (Orthogonal Central Compositional Planning in High Voltage Engineering and Electrophysics: Practical Manual), Kharkov: Nats. Tekh. Univ, KhPI, 2007.
Saprykina, N.A., Saprykin, A.A., and Arkhipova, D.A., Influence of layer-by-layer laser sintering on the quality of the sintered surface layer of products, Trudy VI Mezhdunarodnoi nauchno-prakticheskoi konferentsii “Innovatsionnye tekhnologii i ekonomika v mashinostroenii” (Proc. VI Int. Sci.-Pract. Conf. “Innovative Technologies and Economy in Machine Engineering”), Tomsk: Tomsk. Gos. Politekh. Univ., 2015, pp. 178–183.
Bezobrazov, Yu.A., Zlenko, M.A., Zotov, O.G., et al., Analysis of the structure of samples obtained by DMLS and SLM by rapid prototyping, Materialy 6-i Mezhdunarodnoi molodezhnoi nauchno-prakticheskoi konferentsii “Innovatsionnye tekhnologii v metallurgii i mashinostroenii” (Proc. Sixth Int. Youth Sci.-Pract. Conf. “Innovative Technologies in Metallurgy and Machine Engineering”), Yekaterinburg: Ural. Gos. Univ.,2013, pp. 154–157.
Funding
This research was carried out with the financial support of the Ministry of Science and Higher Education of the Russian Federation in the framework of the program of activities of the Perm Scientific and Educational Center “Rational Subsoil Use.”
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Muratov, K.R., Gashev, E.A., Ablyaz, T.R. et al. Influence of Internal Structure on the Machining of VT6 Titanium Alloy Produced by Additive Technology. Russ. Engin. Res. 41, 836–838 (2021). https://doi.org/10.3103/S1068798X21090215
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X21090215