Skip to main content
SpringerLink
Log in

Determination of particle size, surface area, and shape of supplementary cementitious materials by different techniques

  • Original Article
  • Published:
Materials and Structures Aims and scope Submit manuscript

Abstract

The particle size distribution, surface area and shape are fundamental characteristics of supplementary cementitious materials (SCMs). Accurate measurement of these properties is required in computational efforts to model the hydration process, and the characterization of these parameters is also an important practical issue during the production and use of blended cements. Since there are no standard procedures specifically for the determination of physical properties of SCMs, the techniques that are currently used for characterizing Portland cement are applied to SCMs. Based on the fact that most of the techniques have been developed to measure cements, limitations occur when these methods are used for other materials than cement, particularly when these have lower fineness and different particle shape and mineralogical composition. Here, samples of fly ash, granulated blast furnace slag and silica fume were tested. Different results obtained using several methods for the determination of specific surface area are presented. Recommendations for testing SCMs using air permeability, sieving, laser diffraction, BET, image analysis and MIP are provided, which represent an output from the work of the RILEM Technical Committee on Hydration and Microstructure of Concrete with Supplementary Cementitious Materials (TC-238-SCM).

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11

Similar content being viewed by others

References

  1. Lothenbach B, Scrivener K, Hooton RD (2011) Supplementary cementitious materials. Cem Concr Res 41(12):1244–1256

    Article  Google Scholar 

  2. Snellings R, Mertens G, Elsen J (2012) Supplementary cementitious materials. Rev Mineral Geochem 74:211–278

    Article  Google Scholar 

  3. Siddique R, Khan MI (2011) Supplementary cementing materials. Springer, Berlin. ISBN 978-3-642-17865-8

    Book  Google Scholar 

  4. Juenger M, Provis JL, Elsen J, Matthes W, Hooton RD, Duchesne J, Courard L, He H, Michel F, Snellings R, Belie ND (2012) Supplementary cementitious materials for concrete: characterization needs. MRS proceedings 1488. doi:10.1557/opl.2012.1536

  5. Arvaniti EC, Juenger MCG, Bernal SA, Duchesne J, Courard L, Leroy S, Provis JL, Klemm A, Belie ND (2014) Physical characterization methods for supplementary cementitious materials. Mater Struct. doi:10.1617/s11527-014-0430-4

  6. EN 196-6 (2010) Methods of testing cement—part 6: determination of fineness

  7. ASTM C430-08 (2008) Fineness of hydraulic cement by the 45-μm (No. 325) Sieve

  8. EN 451-2 (1995) Method of testing fly ash—part 2: determination of fineness by wet sieving

  9. ASTM C204-11 (2011) Standard test methods for fineness of hydraulic cement by air-permeability apparatus

  10. ISO 13320:2009 (2009) Particle size analysis—laser diffraction methods. Part I: general principles

  11. ISO 9277 (2010) Determination of the specific surface area of solids by gas adsorption—BET method

  12. ISO 13322-1 (2010) Particle size analysis—image analysis methods—part 1: static image analysis methods

  13. Mayer RP, Stowe RA (1965) Mercury porosimetry—breakthrough pressure for penetration between packed spheres. J Colloid Sci 20:893–911

  14. Mayer RP, Stowe RA (2005) Packed uniform sphere model for solids: interstitial access opening sizes and pressure deficiencies for wetting liquids with comparison to reported experimental results. J Colloid Interface Sci 294:139–150

    Article  Google Scholar 

  15. Hewlett P (2003) Lea’s chemistry of cement and concrete, 4th edn. Butterworth Heinemann, Lodon

    Google Scholar 

  16. EN 196-2 (2005) Methods of testing cement—part 2: chemical analysis of cement

  17. EN 451-1 (2004) Fly ash for concrete—part 1: definition, specifications and conformity criteria

  18. EN 197-1 (2000) Cement—part 1: composition, specifications and conformity for common cements

  19. Malvern MAN 0396 Issue 1.0 (2007) Sample dispersion and refractive index guide. Mastersizer 2000

  20. Gregoire MP, Dislaire G, Pirard E (2007) Accuracy of size distributions obtained from single particle static digital image analysis. In: Proceedings of Partec conference. Nürenberg 2007, p 4

  21. Michel F, Gregoire M, Pirard E (2007) Size distribution of powders in range of 1–100 µm: a comparison of static digital image analysis and laser diffraction. In: Proceedings of Partec conference. Nürenberg 2007, p 4

  22. León CA (1998) New perspectives in mercury porosimetry. Adv Colloid Interface Sci 76–77:341–372

    Article  Google Scholar 

  23. ASTM C618-12a (2012) Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete

  24. ASTM C989/C989 M—13 (2013) Standard specification for slag cement for use in concrete and mortars

  25. Teipel U, Winter H (2011) Characterization of the specific surface area with the permeation method. In: At mineral processing 52

  26. Arvaniti EC, Belie ND (2014) Method development for the particle size analysis of supplementary cementitious materials. In: XIII DBMC, Sao Paulo, Brazil, 2–5 Sept 2014 (to be published)

  27. Quercia G, Hüsken G, Brouwers HJH (2012) Water demand of amorphous nano silica and its impact on the workability of cement paste. Cem Concr Res 42(2):344–357

    Article  Google Scholar 

  28. Leroy S, Dislaire G, Bastin D, Pirard E (2011) Optical analysis of particle size and chromite liberation from pulp samples of a UG2 ore regrinding circuit. Miner Eng 24:1340–1347

    Article  Google Scholar 

  29. Tinke AP, Carnicer A, Govoreanu R, Scheltjens G, Lauwerysen L, Mertens N, Vanhoutte K, Brewster ME (2008) Particle shape and orientation in laser diffraction and static image analysis size distribution analysis of micrometer sized rectangular particles. Powder Technol 2(186):154–167

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Magnel Laboratory for Concrete Research, Department of Structural Engineering, Faculty of Engineering and Architecture, Ghent University, Technologiepark Zwijnaarde 904, 9052, Ghent, Belgium

    Eleni C. Arvaniti & Nele De Belie

  2. Department of Civil, Architectural and Environmental Engineering, University of Texas at Austin, 301 E. Dean Keeton St. C 1748, Austin, TX, 78712, USA

    Maria C. G. Juenger

  3. Department of Materials Science and Engineering, University of Sheffield, Sheffield, S1 3JD, UK

    Susan A. Bernal & John L. Provis

  4. Département de géologie et de génie géologique, Université Laval, Pavillon Adrien-Pouliot, local 4507, 1065, ave de la Médecine, Quebec, QC, G1V 0A6, Canada

    Josée Duchesne

  5. GeMMe Research Group, ArGEnCo Department, University of Liege, Liege, Belgium

    Luc Courard & Sophie Leroy

  6. Department of Construction and Surveying, School of Engineering and Built Environment, Glasgow Caledonian University, Cowcaddens Road, Glasgow, G4 0BA, UK

    Agnieszka Klemm

Authors
  1. Eleni C. Arvaniti
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Maria C. G. Juenger
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Susan A. Bernal
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Josée Duchesne
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Luc Courard
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Sophie Leroy
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. John L. Provis
    View author publications

    You can also search for this author in PubMed Google Scholar

  8. Agnieszka Klemm
    View author publications

    You can also search for this author in PubMed Google Scholar

  9. Nele De Belie
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Nele De Belie.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Arvaniti, E.C., Juenger, M.C.G., Bernal, S.A. et al. Determination of particle size, surface area, and shape of supplementary cementitious materials by different techniques. Mater Struct 48, 3687–3701 (2015). https://doi.org/10.1617/s11527-014-0431-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1617/s11527-014-0431-3

Keywords

Search

Navigation