Abstract
The sensitivity to angular rotation of the top class Sagnac gyroscope GINGERINO is carefully investigated with standard statistical means, using 103 days of continuous operation and the available geodesic measurements of the Earth angular rotation rate. All features of the Earth rotation rate are correctly reproduced. The unprecedented sensitivity of fractions of frad/s is attained for long term runs. This excellent sensitivity and stability put Sagnac gyroscopes at the forefront for fundamental physics, in particular for tests of general relativity and Lorentz violation, where the sensitivity plays the key role to provide reliable data for deeper theoretical investigations.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Ring Laser Gyroscopes (RLGs) exploit the Sagnac effect – i.e. the interference of two counter-propagating photon beams in a closed optical path – to measure absolute rotation of the apparatus with respect to the local inertial frame [1]. For the last 40 years large-scale versions of RLGs have been regarded as a promising tool for geodesy and fundamental physics researches [2, 3]. A relevant contribution to geodesy is a more accurate estimate of Earth Rotation Parameters (ERP) [4], i.e. polar motion and sub-daily variations of universal time, that correspond to direction and modulus of the Earth angular velocity vector, respectively. RLGs eventually should provide to the International Earth Rotation System (IERS) [5] a continuous, faster, high-resolution measurement of the ERP, complementary to the well-established methods based on VLBI and GNSS (e.g. GPS, LSR, DORIS, etc.) data. Further to ERP measurements with ground-based instrumentation, challenging tests of fundamental physics can be carried out with RLGs by studying the tiny residuals of the proper time difference between the counter-propagating photon beams, which last once any known rotation contribution (geophysical, geodetic or local) has been taken into account and subtracted. These residuals are directly connected to metric description of local space-time geometry [6] or searches for Lorentz violations [7].
Unfortunately, the non-linearities induced by laser dynamics have made the RLG applications less attractive, and prevented the full comprehension of long term stability and sensitivity of RLGs. The laser dynamics corrections [8,9,10,11,12,13] are unavoidable if the RLG top sensitivity must be pushed towards testing space-time structures and symmetries, beyond the experimental results in gravitational or particle physics already available in the literature [14, 15]. In this regard, we have recently demonstrated that effects of non linear dynamics can be cancelled at a level of one part in \(10^3\) and this was enough to push the sensitivity of our RLG to sub-prad/s rotation rates [16]. It is remarkable that also cold atoms in a Sagnac interferometer achieved a pretty good sensitivity. However, there is a \(\sim 5\) orders of magnitude gap in rotation sensitivity between current devices and large-scale RLGs [17,18,19]. Another interesting gyroscope design is based on passive optical cavities which have been studied for gravitational waves detectors [20, 21], and are foreseen for space based gravitational waves antennas [22,23,24], but they have not yet demonstrated sufficient sensitivity.
Notable general relativity (GR) tests with gyroscopes are the measurement of the De Sitter effect due to the curvature of space-time around the Earth and of the Lense–Thirring effect due to the Earth rotation (dragging of the local inertial frames) [25]. Such tests are based on the comparison between the Earth angular velocity vector as estimated by IERS and the corresponding measurements obtained by an array of RLGs. Moreover, a RLG array can reconstruct the “local geometry” of null geodetics of space-time and test whether it fully corresponds to the GR description or it requires GR extensions or modifications [26, 27]. Though at the level of the solar system GR well fits experimental observations, it suffers several shortcomings from the very small up to the cosmological scales. For example, it cannot predict the right correlation between mass and radius of some neutron stars [28, 29], the galaxy rotation curve without introducing Dark Matter [30, 31], or the accelerated expansion of the Universe in the late time without introducing Dark Energy [32]. Dark Matter and Dark Energy are supposed to represent the 26.8% and 68% of the Universe content, but have never been detected directly.
At the small scales, while Strong and Electroweak interactions can be dealt with under the standard of quantum field theory, many issues arise in the attempt to merge the formalism of GR with that of quantum mechanics [33,34,35]. Indeed, in view of a possible quantum scheme, the spacetime metric should represent both a dynamical field and the background. This is not the case of other interactions, whose treatment is simplified by the assumption that the spacetime is supposed to be flat. Also, from quantum field theory in curved spacetime, a discrepancy of 120 orders of magnitude occurs between the theoretically predicted value of the cosmological constant and the experimentally observed one.
Modified theories of gravity arose with the purpose of solving such shortcomings, by considering alternatives to the Einstein–Hilbert action [27, 36]. GR can be modified in several ways, such as introducing the coupling between geometry and scalar fields [37, 38], higher-order curvature invariants [39,40,41], torsion and non-metricity [26, 42], or by not requiring the equivalence principle to hold a priori [43].
In this context, experimental observations play a fundamental role. On the one hand, they can be used to constrain dynamical degrees of freedom occurring in modified theories of gravity [44], selecting physically relevant theories. One the other hand, observations may address the research for GR extensions towards viable models, also suggesting the scales in which such extensions are needed.
For instance, in [45], post-Newtonian approximation is used to put upper limits to the functional form of a higher-order scalar-tensor action; in [46] f(R) gravity is constrained by solar system tests; in [47] the fundamental plane of galaxies is addressed to geometric contributions; in [48] non-local theories of gravity are selected by S2 star orbit.
Other interesting tests searching for new physics involve the local Lorentz invariance, since well motivated extensions of the Standard Model for particle physics predict Lorentz violation terms, that can be checked by the interference of the two counter-propagating beams of light [7].
All such unique features of RLGs motivated us to propose the GINGER experiment [49, 50] and to build its test bed GINGERINO [51, 52] at the underground Gran Sasso laboratory. GINGERINO is a 3.6 m side RLG that has been taking data in an almost continuous basis since 2017; it runs unattended and free running ensuring a duty-cycle around 80% even in the absence of an active geometry control [53]. This large amount of data gives us the possibility to improve the comprehension of the instrument, understand its sensitivity limits, and assess the feasibility of long term operation. Our activity is aimed at improving the experimental set-up of the future GINGER array taking full advantage of the very careful analysis of GINGERINO data, where weak points of the system design can be identified, and the origin of disturbances or limitations in the sensitivity can be investigated. In general terms, the study of very high sensitivity apparatus is rather difficult, since it deals with noise. The validity of Earth based tests depends on the effective sensitivity of the apparatus, since for both GR and Lorentz violation the sensitivity indicates whether the test is competitive with the existing experimentally established limits. The watershed in both cases is to discriminate variations of the Earth rotation rate down to 1 part in \(10^9\). GINGERINO has the advantage to be sensitive to the global geodetic signals of the Earth, as Chandler and Annual wobbles, polar motions and variations of the universal time. These are rather small signals independently and constantly measured by the international system IERS with very high accuracy. Therefore geodesy provides the signals to investigate the sensitivity of the apparatus. It has been recently demonstrated that GINGERINO reaches the sensitivity limit of 40 frad/s in 3.5 days of integration [16], effectively crossing the fundamental physics watershed. That analysis has shown the dominant role of the tilt measurements in the identification and subtraction of the local disturbances. Aim of the present analysis is to improve the identification and subtraction of the local and instrumental disturbances by developing a more effective treatment of the signals produced by the tiltmeters implemented in the RLG set-up. To fully exploit the GINGERINO sensitivity we have also improved the cross calibration procedure with the IERS data. The unprecedented sensitivity of the order of 1 part \(10^{12}\) of the Earth rotation rate appears, which is even better than one hundred times the Lense–Thirring effect with a bandwidth corresponding to a 600 s integration time and long term operation. The result shows that it is possible to bring down to \(0.1\%\) the Lense–Thirring test planned for GINGER, a factor ten improvement with respect to the original proposal.
Plan of the paper is as follows. In Sect. 2 the general scheme of the analysis is outlined. Section 3 reports the results of the analysis applied to 103 days of data, illustrating the calibration procedure and the relative sensitivity, and indicating the main instrumental limits of the apparatus. In Sect. 4 we investigate the occurrence of signals due to deformation of the Earth crust. Section 5 reports a general discussion about the analysis. Conclusions are eventually drawn in Sect. 6, including what we have learned in view of GINGER and its application for fundamental physics measurements.
2 Purpose and general scheme of the analysis
Purpose of the analysis is to reconstruct the Earth angular rotation rate and the instrumental disturbances using the RLG data and the environmental signals with the final goal of improving sensitivity and investigating its effective value. The procedure uses linear regression (LR) model [54,55,56,57] minimising the square of the difference between the evaluated and independently measured rotation rates. To this end it is mandatory to subtract the contributions induced by the non linear laser dynamics [12, 13]. In the following the main properties of the Sagnac frequency, the Earth rotation rate, the experimental set-up, and the analysis components are summarised.
2.1 The Sagnac frequency
The Sagnac gyroscope is identified by the oriented area \(\mathbf {A}\) enclosed by the optical path and the perimeter P corresponding to its length. The Sagnac beating signal \(\omega _s\)Footnote 1 is proportional to the scalar product between \(\mathbf {A}\) and the total angular velocity \(\mathbf {\Omega }_T\) of the RLG optical cavity. Without loss of generality, we can write
where \(\lambda \) is the laser wavelength, and \(\mathbf {\Omega }_{loc}\) is the sum of all possible angular velocities associated with Earth crust deformations and instrument infinitesimal rotations. In general, local rotations are unknown in amplitude and direction but very small compared to the Earth rotation rate \(\Omega _\oplus \), and so they contribute to the Sagnac signal as an additive perturbation. Here, \(\mathbf {\Omega }_\oplus \) describes the Earth rotation rate and its orientation, \(\gamma \) is the angle between the area vector and the rotation axis, corresponding to the laboratory co-latitude for horizontal RLGs, and SF is the scale factor. In our analysis the \(\cos \gamma \) is associated with the scale factor to simplify the discussion, since effects of geometrical scale factor changes cannot be distinguished from orientation changes. The modulus and direction of \(\mathbf {\Omega }_\oplus \) changes in time, however it is continuously monitored by IERS. In the following we will use uppercase \(\Omega \) and lowercase \(\omega \) for angular velocity (in units of rad/s) and the corresponding Sagnac angular frequency, respectively.Footnote 2 In addition, their time dependence will not be explicitly indicated.
2.2 Geodesic signals
The international system IERS provides the data to describe the Earth motion on a daily basis, from which it is possible to reconstruct the effect on GINGERINO, called geodesic signal \(\Omega _{_{IERS}}\), as the sum of the average Earth rotation rate \(\Omega _\oplus \), the Length of Day (LoD) changes, celestial pole offsets, UT1–UTC, polar motion and diurnal and semi-diurnal variations produced by ocean tides [5]. In the present analysis the \(\Omega _{_{IERS}}\) time series is downloaded from Earth orientation center of the Paris observatory [58].
2.3 GINGERINO experimental set up and data analysis
GINGERINO is a RLG with a square laser cavity, 3.6 m in size. It is installed horizontally with its area vector aligned with the local vertical. Its design is based on a hetero-lithic (HL) mechanical structure, the 4 mirrors at the corners of the cavity are contained inside vacuum tight boxes and connected together by vacuum tubes. Interested readers can find more details in the literature [51, 52]. The mechanical structure is attached to a cross shaped monument made of granite, connected in the center to the underneath bedrock through a reinforced concrete block. The set-up is located underground, where typical day-and-night temperature variations are strongly suppressed, and far from anthropic disturbances. The apparatus is protected by a cabinet, far from the large experimental halls of the Gran Sasso laboratory, moreover the electronics is contained in a separated room. The laser optical cavity is aligned at the beginning of the run, and after that it operates continuously and unattended. The geometry is not electronically controlled, this implies that mode jumps and split lasing mode occur. Routinely more than \(90\%\) of the data are of good quality [52]; however, for the present analysis data around laser mode jumps are discarded, leading us to keep no more than \(80\%\) of the complete data set.
2.4 Model and parameters of the analysis
The Sagnac frequency \(\omega _{s}\) has to be evaluated by taking into account laser dynamics contribution \(\omega _{LD}\), (i.e. \(\omega _{s} = \omega _{s0}-\omega _{LD}\), where \(\omega _{s0}\) is a first estimation of the Sagnac signal, as described in details in Refs. [12, 13, 16, 59]), and then it can be expressed as
where \(K_{cal}\) is a cross calibration constant, very close to 1, found by comparing \(\omega _s\) and \(\omega _{_{IERS}}\), the angular frequency related to the \(\Omega _{_{IERS}}\) data, and the term representing local rotations \(\omega _{loc} = \omega _{env} + \omega _{ins}\), which takes into account signals of environmental and geophysical origin \(\omega _{env}\), and rotations of instrumental origin \(\omega _{ins}\). The present analysis does not distinguish between \(\omega _{ins}\) and \(\omega _{env}\), but they are kept separated as, in principle, we could get rid of \(\omega _{ins}\) with an improved design of RLG. To this aim, we are investigating the causes of the disturbances of an instrumental origin with a dedicated analysis [60].
The \(\omega _{LD}\) contribution is evaluated including in the LR the 6 explanatory variables that correspond to the signals collected at the output ports of the square cavity, i.e. the beat note of the two counter propagating beams, the DC amplitudes of the two mono beams \(IS_{1,2}\), their AC amplitudes \(PH_{1,2}\), and their relative phase \(\epsilon \). Other explanatory variables come from the available environmental signals: temperature, pressure, air flow speed, the two channels (\(\zeta _{1,2}\)) of the tiltmeter located on top of the granite table. The procedure is iterative as some explanatory variables have to be elaborated using a rough estimate of \(\omega _s\), \(\omega _{loc}\) and some environmental signals.
2.5 Explanatory variables of the linear regression (LR)
The present analysis extends and refines the multiple linear regression procedure outlined in our recent work [16]. It is worth noticing that the environmental infinitesimal rotations affect at the same time the Sagnac angular frequency \(\omega _s\) and the laser dynamics contribution \(\omega _{LD}\). For this reason \(\omega _{LD}\) is evaluated at the beginning with the complete set of available explanatory variables related to laser dynamics and environmental sources. In any case, the final result remains unchanged if all the terms are kept in the LR procedure until its end. Outputs of the analysis are an estimate of the geodesic signal reconstructed from the RLG data \(\omega _{geo}\), the local angular velocity \(\omega _{loc}\), and the residual of the model \(\varDelta M_{LR}\), which provides an insight into physical phenomena not included in the proposed model. The term accounting for local rotations and the residuals read, respectively,
where \(env_j\) are temperature, pressure, air flow speed, and the two tiltmeter signals \(\zeta _{1,2}\), the time series \(\tilde{F}_{k}\) are the product of the \(\zeta _{1,2}\), or the DC monobeam signals \(PH_{1,2}\), mainly with \(\omega _{loc}\), but also with residuals of an intermediate stage, and \(a_i\), \(b_j\), \(c_k\) are weights of the LR procedure. The use of the explanatory variables \(\tilde{F}_k\) has been suggested by our recent work [16]. However, \(\zeta _{1,2}\) and the relative products with \(\omega _s\) were used in Ref. [16] as separated explanatory variables. The present analysis indicated that the effective variable was the combination of the two, in the form of \(\zeta _{1,2} \omega _{loc}\). To obtain \(K_{cal}\) and \(\omega _s\), the LR is iterated a few times using at the first step only \(\omega _{LD}\) to provide a first evaluation of \(\omega _s\). The calibration value \(K_{cal}\) is determined by imposing that at a fixed time T\(_0\), arbitrarily chosen, the intercept \(I_{T_0}\) of the LR is close to zero, i.e. \(K_{cal} = (\Omega _{geo}(T_0)+I_{T_0})/\Omega _{_{IERS}}(T_0)\); in the iterative estimation of \(\omega _s\) this procedure is repeated.Footnote 3
The estimation of the geodesic angular frequency \(\omega _{geo}\) is given by
We noticed that \(K_{cal}\) depends mostly on the absolute orientation of the device. Being \(\theta \) the colatitude, and assuming that the geometry of the laser cavity is stable in time because the temperature is rather stable and geometrical variations are consequently small, it is possible to estimate the inclination of the RLG at the cross calibration time, \(\theta _{css} = \arcsin ({\sin {\theta }\cdot K_{cal}})\).
Although the complete set of explanatory variables is used in the initial analysis, we eventually keep only the statistical independent ones that affect the residuals. Accordingly, we neglect in our final elaboration pressure and air flow speed signals, since they demonstrated a negligible effect.
3 Analysis results
The LR method has been applied to a set of data from day 1 to 103 of year 2020. The variables indicated in Eqs. 3-6 are time series with \(\frac{1}{600}\)Hz sampling rate. Typical results changing the cross calibration point reconstruct correctly \(\Omega _{geo}\), the angular velocity variations associated with \(\omega _{geo}\). For example, at cross calibration \(T_0\), modified Julian date 58886.23611, \(K_{cal}= 1.000120452\), corresponding to a misalignment with respect to the RLG horizontal orientation of about 0.1 mrad (at the cross calibration time). We emphasize that the relevant signals are reproduced with a standard deviation of the residuals \(\varDelta M_{LR}\) at the nHz level. Figure 1 shows the evaluated true Sagnac signal \(\omega _s\), and Fig. 2 compares the effects on the RLG of \(\Omega _{geo}\) and \(\Omega _{IERS}\), expressed in units of frequency, Hz (corresponding in our notation to \(\omega _{geo}/2\pi \) and \(\omega _{_{IERS}}/2\pi \), respectively). The agreement between the IERS data and the evaluated \(\Omega _{geo}\) is so good that the two curves are almost perfectly over imposed each other in Fig. 2.
Remarkably, the output of the LR analysis for the laser dynamics and local disturbances leads to non negligible contributions Their standard deviations, in units of frequency, are as large as 6 mHz and 4.5 mHz, respectively, strongly suggesting that the related effects must be carefully accounted for in order to improve the instrumental sensitivity. Note that \(\omega _{LD}\) has a bias close to 0.5 in units of frequency, remarking the importance of the laser dynamics correction not only for the sensitivity, but as well for the accuracy, which is the key issue of GR tests [12, 13].
The residual \(\varDelta M_{LR}\) is associated with portions of the data which cannot be explained by the model. Inclusion in the set of explanatory variables of those created by multiplying \(\omega _{loc}\) by \(\zeta _{1,2}\) and the DC mono beam signals has impact in the results: we denote such variables as projectors, since they are scalar products. In particular, for GINGERINO, mainly \(\zeta _{1,2}\) signals are used in the projectors, being the use of the \(PH_{1,2}\) less relevant. Typical \(\varDelta M_{LR}\) using a set of 4 or 5 projectors leads to a standard deviation as small as 4 nHz in units of frequency (corresponding to 0.7 frad/s in angular velocity).
The Overlapping Allan Deviation (OAD) of the residuals \(\varDelta M_{LR}\), which provides information on noise and measurement sensitivity as a function of the integration time \(\tau \), is shown in Fig. 3. Remarkably, OAD is always below 6 parts in \(10^{12}\) of the Earth rotation rate, well below the target meaningful for fundamental physics and geodesy, reported to be 1 part in \(10^9\) [7, 16, 49, 50]. Moreover, the analysis has been repeated using 30 days of June 16-July 15 2018, obtaining a very similar behaviour of the OAD.
3.1 Calibration by sinusoidal signal injection
The residuals provide the estimation of the sensitivity level. Since this value contains bias due to the tide models, we have implemented a supplementary method to estimate GINGERINO sensitivity by adding to \(\omega _s\) two sinusoidal signals, with frequency different from common tides. Then we run the LR procedure, including the explanatory variables that correspond to these probe signals. By looking at the results, in particular at the precision of the estimated probe parameters, we are able to calculate the signal to noise ratio and the sensitivity of the method at the frequency of the sinusoidal signals. In particular, the amplitude of the probes is \(2.6\cdot 10^{-7}\) Hz (corresponding to the magnitude of the Lense-Thirring effect at the GINGERINO site), whereas their periods are 40 days and 0.5 days, respectively. They are recovered by the LR analysis with a signal to noise ratio of \(\sim 500\) and \(\sim 1000\), respectively, corresponding approximately to noise floors of 0.5 nHz and 0.3 nHz in units of frequency (i.e. 0.1 frad/s and 0.05 frad/s in angular velocity), with a bandwidth corresponding to a 600 s integration time.
3.2 Correlation between \(\omega _{loc}\) and \(\zeta _{1,2}\)
The present analysis shows a strong correlation between RLG and tiltmeter signals. Note that GINGERINO is a HL mechanical device, and its mirrors are not rigidly connected to the monument because there are mechanical levers used to align the square cavity. Those levers are not fixed and, in case of monument tilts, the mechanical components will have different equilibrium configurations to compensate gravitational force. Since the mechanical parts are connected to each other, the whole effect is an effective rotation of the laser cavity. From \(\omega _{loc}\), it is possible to estimate the effective phase \(\phi \) of the rotation. It has been straightforward to see a linear relation between the effective inclination of the monument and the reconstructed \(\phi \) obtained by time integration of \(\omega _{loc}\), the effective rotation of the device with respect to the ground. This is a clear indication that the GINGERINO cavity rotates when the granite table changes its orientation [60]. The correlation is not always linear, indicating that the HL mechanical cavity has a complex behaviour.
4 Close look to the main features of the Earth rotation rate
Known geophysical signals provide a real and effective playground for the analysis of GINGERINO data. The Earth rotation rate contains several important features, as LoD effects, Earth normal modes and deformations induced by tides. Accordingly \(\Omega _{IERS}\) is the sum of different contributions, which can or not be taken into account in the analysis. Comparing the results obtained with different contributions to \(\Omega _{_{IERS}}\) it is possible to isolate each contribution by subtracting the different \(\Omega _{geo}\) elaborated by the different input models. In this way the analysis has been already able to reproduce LoD effects by providing the term \(\varDelta \omega _3\) [16]. This procedure has been repeated to evaluate LoD and the variations produced by ocean tides contributions, obtaining always results in agreement with the expectations, with a discrepancy even smaller than 1 part in \(10^3\), consistent with the sensitivity of the apparatus, as shown for example in Fig. 3.
4.1 Effects of tides and Earth normal modes
Since Earth is not a rigid body, tides and normal modes of the Earth induce crust deformations. As a consequence, angular rotations of the GINGERINO site occur; in the following we focus on the effects due to tides and normal modes of the Earth. The angular rotation signal provided by IERS contains global signals, as polar motions, but also local signals caused by the deformation of the crust induced by tides or ocean loading. Figure 4 compares the Amplitude Spectral Density (ASD) of \(\omega _{IERS}\) and \(\omega _{geo}\); the semi diurnal peak, at a frequency slightly above \(2\times 10^{-5}\) Hz, is caused by the solid Earth tide, \(\omega _{geo}\) and \(\omega _{IERS}\) are in good agreement each other in that frequency region.
Deformations associated with Earth normal modes have a typical frequency above 0.3 mHz (corresponding to a period below 53.9 prime minutes). Figure 5 reports an expanded view of the ASD in the relevant frequency range. As demonstrated by the comparison of predictions and analysis results, very small and tiny peaks due to deformations are well reproduced, although peak amplitude is systematically smaller by more than \(10\%\) with respect to the predictions based on IERS data.
Detail of the rotation associated with Earth normal modes. The agreement with IERS expectation shows equal frequency, while the amplitude of the different components is systematically smaller by more than \(10\%\). In the plot the positions of several well known resonances are qualitatively indicated for comparison
Owing to the small amplitude of the signals relating to normal modes, much smaller than typical disturbances of the apparatus, at the present stage of the analysis we cannot definitely conclude that the instrumental sensitivity is large enough to truly reconstruct their occurrence in the considered frequency range. In general the agreement is very good in the semi-diurnal signal, corresponding to a larger amplitude, while normal modes are found systematically smaller in amplitude.
4.2 Attempts to evaluate the rotation caused by deformation
Further analysis has been done on this important subject, in order to recover the contribution of the diurnal and semidiurnal variations produced by ocean tides, which will be called \(\Omega _{def}\) in angular velocity and as \(\omega _{def}\) in the relative effect on the Sagnac signal. The analysis pipeline has been repeated using \(\Omega ^{\prime }_{IERS}\), i.e. the expected global signal without the tide effects \(\Omega _{def}\), as it can be obtained with the available online tools. For this analysis the June–July 2018 data set, 30 days, has been used, since at that time the temperature variations were a factor 5 smaller than for the 2020 data set, and the corresponding standard deviation of \(\omega _{loc}\) was 4 times smaller. The estimation of \(\omega _{def}\) is done subtracting the global and local signals estimated in the two different analysis. In general, \(\Omega _{geo}-\Omega ^{\prime }_{geo}\) is equal to \(\Omega _{def}\) at the level of tens of frad/s, while the difference \(\omega ^{\prime }_{loc}-\omega _{loc}\) is close to \(\omega _{def}\) with a noise of fractions of \(\mu \)Hz. Figure 6 shows the amplitude spectral density of \(\omega _{def}\) and \(\omega ^{\prime }_{loc}-\omega _{loc}\). In this case, the Earth normal modes are below the noise spectral density.
5 Discussions and findings
The analysis is based on the hypothesis that the Sagnac frequency \(\omega _s\) is the sum of different components: laser disturbances \(\omega _{LD}\), geodesic global signals \(\omega _{geo}\) (to be compared to the IERS measurement \(\omega _{_{IERS}}\), which is used in the model) and local disturbances \(\omega _{loc}\). The model attempts to estimate \(\omega _{loc}\) as the sum of terms independently evaluated using the environmental signals as explanatory variables, in particular temperature, tilts and mono beam amplitudes. GINGERINO is affected by many disturbances, but since their amplitudes are very small, it is taken for granted that they can be eliminated from \(\omega _s\) with the linear regression, assuming linear (or second order) expansion of the transfer functions of the environmental signals. It is worth noticing that the \(\omega _{LD}\) contribution is comparable to \(\omega _{loc}\) and cannot be neglected, or in other words the LR with environmental signals is not able to identify the local disturbances. It is crucial to identify and subtract \(\omega _{LD}\), since it prevents the estimation of the angular velocity of the apparatus by means of a linear analysis approach, owing to the non linearities of the laser dynamics and the relevance of their effects. The described interpretation of GINGERINO data is confirmed by the comparison with the monolithic RLG of the Wettzell Observatory G, which is not limited by large disturbances of instrumental origin, and low frequency angular rotations around the vertical axis of geophysical origin [61].
The general outcome of our analysis is that \(\omega _s\) is dominated by local disturbances, which can be eliminated below the 10 nHz noise level in units of frequency by using the tiltmeter data. Sensitivity of the order of nHz or even better shows up, compatible to approaching a few part in \(10^{12}\) of the Earth rotation rate. However, the method relies on the accuracy of the explanatory variables and it cannot be considered predictive. In fact, we have the convergence of LR analysis (with larger residuals), even if we perturb some explanatory variables (for instance by slightly changing the Earth rotation model).
The analysis shows that the sensitivity of the apparatus is more than two orders of magnitude better than expected [1]. The debate around RLG sensitivity is still active, mainly focusing to very small RLGs [62]; so far the limit for large frame, high sensitivity RLGs is considered to be the shot noise due to spontaneous emission of laser atoms [63].
Sensitivity is the key point for any fundamental physics application of RLGs, and this discrepancy with the expected noise level will deserve further investigation from theoretical side. It is important to note that the nonlinear dynamics of the laser affects all the spectrum, preventing an evaluation of the measurement limits by looking only at the high frequency part of the spectrum.
6 Conclusions
GINGERINO is a top sensitivity RLG, running far from external disturbances and protected from large thermal excursions in the deep underground environment. Its data are compared with the global signal of the Earth rotation provided by IERS. The present analysis takes into account and eliminates the nonlinear disturbances originated by the laser dynamics and recovers the global IERS signal with all its main features. The obtained residuals, i.e. the unmodeled part of the Sagnac signal, showing a standard deviation of the order of a few nHz, indicate an unprecedented rotational sensitivity below the frad/s level. By injecting probe signals in the GINGERINO data, a sensitivity of 0.1 frad/s with 600 s integration time is suggested. This indicates the feasibility of Lense–Thirring tests at the \(0.1\%\) level, a factor 10 improvement with respect to the first GINGER proposal, eventually enabling also to discriminate among different theories of gravitation [64].
So far measurements of the Lense–Thirring effect have been done by space experiments, using the gravity map of the Earth independently measured by the GRACE mission, and providing latitude averaged measurements [65,66,67,68]. The promise of the GINGER project is the direct and local measurement of the main GR features. To this aim, high accuracy is necessary, and the cross calibration used in the present analysis has to be replaced by independent measurements of the scale factor, to be electronically controlled during the RLG operation [53]. The inclination angle \(\theta \) has also to be evaluated independently: GINGER foresees the use of an RLG oriented at the maximum Sagnac signal, i.e. with its area vector parallel to the north pole direction. Being its signal sensitive only at the second order to local tilts, it can be used as a reference to determine the relevant inclination angles for the other RLGs of the array.
The present analysis on GINGERINO data indicates that residual disturbances are mainly of an instrumental origin, suggesting the need for improvements in the mechanical design in view of GINGER. Mechanical deformations and uncontrolled rocking of the HL set-up, presently responsible for disturbances hundreds of times larger than the signals we are looking for, have to be reduced by a careful design of the mechanical scheme. Moreover, long term thermal stability is also of paramount importance, as discussed in [60], and should also be improved.
In the near future we will devote efforts to investigate the whole operation of the RLG from a theoretical side, with the aim to develop a Monte Carlo simulation carefully accounting for all effects relating with laser dynamics. Comparison with simulations is expected to identify possible further improvements in our analysis and to point out the effective sensitivity limit of the RLG. Moreover, work is in progress to apply the analysis scheme to data acquired by the RLG of the geodesic observatory of Wettzell, in order to remove nonlinear laser dynamics effects and improve its sensitivity.
Data Availability Statement
The manuscript has associated data in a data repository. [Authors’ comment: The data supporting the findings of this paper are available from the corresponding author upon reasonable request.]
Change history
26 May 2021
An Erratum to this paper has been published: https://doi.org/10.1140/epjc/s10052-021-09231-4
Notes
The conventional symbol to denote the Sagnac signal is \(f_s\), as it is practical to measure beating frequencies in Hz. We use instead \(\omega _s = 2 \pi f_s\) because the angular frequency is used in back scattering calculations and its introduction leads to an adimensional scale factor in Eq. (1).
Note, however, that for the sake of clarity we will use frequency units, in Hz, when numerical evaluations of quantities and uncertainties related to angular frequencies \(\omega \) will be given all through the text and figures.
To correctly evaluate \(\Omega _{_{IERS}}\) it is required to measure both the angle \(\theta \) of the area vector of the RLG with respect to the rotational axis and the geometrical scale factor GSF \(= 2 \pi A/(\lambda P)\). With a single RLG, as in the case of GINGERINO, we can estimate only a combination of the two quantities. Due to local rotations, the orientation of our apparatus is not fixed in time at the level of its sensitivity. Therefore, the model cross calibrates at the time \(T_0\) and any change recovered by first and second order expansions is reconstructed by the LR analysis using the information of the explanatory variables. Assuming FS the scale factor for horizontal orientation, the effective scale factor at the cross calibration point is \(K_{cal}\, \text {FS}\), and so \(\omega _{s}(T_0) - \omega _{loc}(T_0) = K_{cal} \, \omega _{_{IERS}}(T_0)\).
References
K.U. Schreiber, J.P.R. Wells, Rev. Sci. Instrum. 84, 041101 (2013)
G.E. Stedman, Rep. Prog. Phys. 60, 615 (1997)
M.O. Scully, M.S. Zubairy, M.P. Haugan, Phys. Rev. A 24(4), 2009–2016 (1981)
S. Böhm, M. Schartner, A. Gebauer, T. Klügel, U. Schreiber, T. Schüler, Adv. Geosci. 50, 9 (2019)
S. Capozziello, M.D. De Laurentis, Phys. Rep. 509, 167 (2011)
S. Moseley, N. Scaramuzza, J.D. Tasson, M.L. Trostel, Phys. Rev. D 100, 064031 (2019)
L.N. Menegozzi, W.E. Lamb, Phys. Rev. A 8, 2103 (1973)
F. Aronowitz, R.J. Collins, J. Appl. Phys. 41, 130 (1970)
A. Beghi et al., Appl. Opt. 51, 7518–7528 (2012)
D. Cuccato, A. Beghi, J. Belfi, N. Beverini, A. Ortolan, A. Di Virgilio, Metrologia 51, 97–107 (2014)
A.D.V. Di Virgilio, N. Beverini, G. Carelli, D. Ciampini, F. Fuso, E. Maccioni, Eur. Phys. J. C 79, 573 (2019)
A.D.V. Di Virgilio, N. Beverini et al., Eur. Phys. J. C 80, 163 (2020)
C. Will, Theory and Experiment in Gravitational Physics (Cambridge University Press, Cambridge, 2018)
A. Kostelecky, N. Russell, Rev. Mod. Phys. 83, 11 (2011)
A.D.V. Di Virgilio et al., Phys. Rev. Res. 2, 032069(R) (2020)
W. Xu, L. Cheng, J. Liu, C. Zhang, K. Zhang, Y. Cheng, Z. Gao, L. Cao, X. Duan, M. Zhou, Z. Hu, Opt. Express 28, 12189–12200 (2020)
I. Dutta, D. Savoie, B. Fang, B. Venon, C.G. Alzar, R. Geiger, A. Landragin, Phys. Rev. Lett. 116, 183003 (2016)
“The Sagnac effect: 100 years later / L’effet Sagnac : 100 ans aprés”, Ed. by A. Gauguet, Comptes Rendus Physique, vol. 15(10) (2014)
D. Martynov, N. Brown, E. Nolasco Martinez, E. Matthew, Opt. Lett. 44, 1584–1587 (2019)
W.Z. Korth et al., Class. Quantum Gravity 33, 035004 (2016)
J. Luo et al., Class. Quantum Gravity 33, 035010 (2016)
F. Zhang, K. Liu, Z. Li, X. Feng, K. Li, Y. Ye, Y. Sun, L. He, K.U. Schreiber, J. Luo, Z. Lu, Class. Quantum Gravity 37, 215008 (2020)
K. Liu, F.L. Zhang, Z.Y. Li, X.H. Feng, K. Li, Z.H. Lu, K.U. Schreiber, J. Luo, J. Zhang, Opt. Lett. 44, 2732–2735 (2019)
F. Bosi, G. Cella, A. Di Virgilio et al., Phys. Rev. D 84, 122002 (2011)
R. Aldrovandi, J.G. Pereira, Fundam. Theor. Phys. 173 (2013)
T. Clifton, P.G. Ferreira, A. Padilla, C. Skordis, Phys. Rep. 513, 1–189 (2012)
J. Antoniadis, P.C.C. Freire, N. Wex, T.M. Tauris, R.S. Lynch, M.H. van Kerkwijk, M. Kramer, C. Bassa, V.S. Dhillon, T. Driebe, Science 340, 6131 (2013)
P. Demorest, T. Pennucci, S. Ransom, M. Roberts, J. Hessels, Nature 467, 1081–1083 (2010)
A. Bosma, Astron. J. 86, 1825 (1981)
J. Beringer et al., [Particle Data Group], “Review of Particle Physics (RPP).” Phys. Rev. D 86, 010001 (2012)
E.J. Copeland, M. Sami, S. Tsujikawa, Int. J. Mod. Phys. D 15, 1753–1936 (2006)
A. Ashtekar, S. Fairhurst, J.L. Willis, Class. Quantum Gravity 20, 1031–1062 (2003)
B.S. DeWitt, Phys. Rev. 162, 1239–1256 (1967)
G. ’t Hooft, M.J.G. Veltman, Ann. Inst. H. Poincare Phys. Theor. A 20, 69–94 (1974)
S. Capozziello, F. Bajardi, Int. J. Mod. Phys. D 28, 1942002 (2019)
F. Bajardi, S. Capozziello, Int. J. Mod. Phys. D 29, 2030015 (2020)
E. Elizalde, S. Nojiri, S.D. Odintsov, Phys. Rev. D 70, 043539 (2004)
F. Bajardi, S. Capozziello, Eur. Phys. J. C 80, 704 (2020)
M. Benetti, S. Santos da Costa, S. Capozziello, J.S. Alcaniz, M. De Laurentis, Int. J. Mod. Phys. D 27, 1850084 (2018)
J.L. Blázquez-Salcedo, F.S. Khoo, J. Kunz, Phys. Rev. D 96, 064008 (2017)
J.B. Jiménez, L. Heisenberg, T.S. Koivisto, Universe 5, 173 (2019)
R. Bousso, Phys. Rev. Lett. 112, 041102 (2014)
N. Radicella, G. Lambiase, L. Parisi, G. Vilasi, JCAP 12, 014 (2014)
S. Capozziello, G. Lambiase, M. Sakellariadou, A. Stabile, Phys. Rev. D 91, 044012 (2015)
A.F. Zakharov, A.A. Nucita, F. De Paolis, G. Ingrosso, Phys. Rev. D 74, 107101 (2006)
S. Capozziello, P. Jovanović, V.B. Jovanović, D. Borka, JCAP 06, 044 (2017)
S. Bahamonde, S. Capozziello, K.F. Dialektopoulos, Eur. Phys. J. C 77, 722 (2017)
A.D.V. Di Virgilio, J. Belfi, W.-T. Ni, N. Beverini, G. Carelli, E. Maccioni, A. Porzio, Eur. Phys. J. Plus 132, 157 (2017)
A. Tartaglia, A. Di Virgilio, J. Belfi, N. Beverini, M.L. Ruggiero, Eur. Phys. J. Plus 132, 73 (2017)
J. Belfi, N. Beverini, F. Bosi et al., Rev. Sci. Instrum. 88, 034502 (2017)
J. Belfi, N. Beverini, G. Carelli, A. Di Virgilio, U. Giacomelli, E. Maccioni, A. Simonelli, F. Stefani, G. Terreni, Appl. Opt. 57, 5844–5851 (2018)
N. Beverini et al., Class. Quantum Gravity 37, 065025 (2020)
S.M. Kay, Fundamentals of Statistical Signal Processing: Estimation Theory (Prentice-Hall Inc, Prentice, 1993)
J. Neter, M.H. Kutner, C.J. Nachtsheim, W. Wasserman, Applied Linear Statistical Models (Irwin, Chicago, 1996)
A. Sen, M. Srivastava, Regression Analysis: Theory, Methods, and Applications. Springer Texts in Statistics (Springer, New York, 1997)
F. Di Renzo, Characterisation and mitigation of non-stationary noise in Advance Gravitational Wave Detectors, Ph.D. Thesis in Physics, University of Pisa, etd-06192020-081853 (2020)
Earth Orientation Matrix and Rotation Vector, https://hpiers.obspm.fr/eop-pc/index.php?index=matrice&lang=en
A.D.V. Di Virgilio, Front. Astron. Space Sci. 7, 49 (2020)
A. Basti, N. Beverini, F. Bosi, G. Carelli, D. Ciampini, A.D.V. Di Virgilio, F. Fuso, U. Giacomelli, E. Maccioni, P. Marsili, A. Porzio, A. Simonelli, G. Terreni, arXiv:2101.07686, EPJP (in press)
K.U. Schreiber, private comunication
J. Ren et al., Opt. Lett. 42, 1556–1559 (2017)
W.W. Chow, J. Gea-Banacloche, L.M. Pedrotti, V.E. Sanders, W. Schleich, M.O. Scully, Rev. Mod. Phys. 57, 61 (1985)
S. Capozziello et al., Constraining Theories of Gravity by GINGER experiment, submitted (2021)
I. Ciufolini, E.C. Pavlis, Nature (London) 431, 958 (2004)
C.W.F. Everitt et al., Phys. Rev. Lett. 106, 221101 (2011)
I. Ciufolini, A. Paolozzi, E.C. Pavlis et al., Eur. Phys. J. Plus 132, 336 (2017)
D.M. Lucchesi, L. Anselmo, M. Bassan, C. Pardini, R. Peron, G. Pucacco, M. Visco, Classical Quantum Gravity 32, 155012 (2015)
Acknowledgements
We would like to express special thanks to Angelo Tartaglia for stimulating ideas and discussions and for his continuous support. We thank the Gran Sasso staff in support of the experiments, particularly Stefano Gazzana, Nazzareno Taborgna and Stefano Stalio . We are thankful for technical assistance to Alessio Sardelli and Alessandro Soldani of INFN Sezione di Pisa and Francesco Francesconi of Dipartimento di Fisica. A special thank to Gaetano De Luca of Istituto Nazionale di Geofisica e Vulcanologia for regularly checking Gingerino operation status.
Author information
Authors and Affiliations
Corresponding author
Additional information
The original online version of this article was revised: Figure 2 has been updated.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Funded by SCOAP3
About this article
Cite this article
Di Virgilio, A.D., Altucci, C., Bajardi, F. et al. Sensitivity limit investigation of a Sagnac gyroscope through linear regression analysis. Eur. Phys. J. C 81, 400 (2021). https://doi.org/10.1140/epjc/s10052-021-09199-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1140/epjc/s10052-021-09199-1