Abstract
A novel thermal lens that can achieve a remote cooling effect is designed by transformation thermodynamics. The effective distance between the separate hot source and cold source is shortened by our shelled thermal lens without any negative thermal conductivity. Numerical simulations verify the performance of our thermal lens. Based on the effective medium theory, we also propose a practical way to realize our lens using two-layered isotropic thermal media that are both found in nature. The proposed thermal lens will have potential applications in remote temperature control and in creating other thermal illusions.
Similar content being viewed by others
Introduction
Transformation Optics (TO) can be utilized to design special electromagnetic media with pre-designed functions by using a coordinate transformation from the virtual space to the real space1,2,3. Many novel optical/electromagnetic devices have been designed by TO, including invisibility cloakings4,5,6, novel lenses7,8, field rotators9,10,11, concentrators12, illusion optical devices13,14, and others. Based on the heat equation’s form-invariant property under coordinate transformations, transformation thermodynamics (TT) was first proposed by Guenneau, S. et al.15. In recent years, manipulating heat flux by a coordinate transformation method has attracted much attention and developed many novel thermal devices, e.g. thermal cloakings16,17,18, concentrators for heat collections19,20, heat hyper-lenses for heat focusing21, heat hoses22, heat flux rotators23, thermal diodes24, heat illusion devices25,26,27,28,29, novel thermal lenses30,31, devices for a heat directional transmission32, etc.
In 2016, our group proposed a novel thermal lens based on spatial translations and folding coordinate transformations together to achieve a remote heating/cooling operation on temperature distribution31. However, it is still challenging to realize the proposed thermal lens due to the negative thermal conductivity introduced from the spatial folding transformation. In some applications, we need a remote cooling technique. In some applications, we want to achieve a very high temperature in an given region (the target region) while not influencing its neighboring area (i.e. the temperature is low around the target region). We need to use a remote cooling technique to cool down the temperature around the target region but not influencing the hot target region. For example, in laser tumor therapy, we hope normal cells around the targeted tumor cell are not killed by the high temperature produced by the laser. In this case, we need a cooling technique to keep the temperature in normal cells relatively low. The cooling source cannot be set inside the human body, which means that a remote cooling technique is required. Such a remote cooling can also be applied to cool down the neighboring area around an inevitable hot site through a remote cold source. In this study, we use the spatial translation and compression transformations together to achieve a remote cooling effect using a thermal lens with homogeneous positive anisotropic thermal conductivity.
Methods
Figure 1(a) shows the basic function of our thermal lens. The whole lens is composed of five different regions of media with homogenous anisotropic thermal conductivity (indicated by different labels). The hot source (a red star) and cool source (blue star) are set in the left and right sides of the region V, respectively, within the shelled structure (i.e. our lens). The function of this shelled lens is to reduce the effective spatial distance between the hot source and the cool source, which makes the cool source effectively much closer to the hot source than their real distance. The effective cooling region is the region outside the shelled structure ABCD.
We now show how to design the proposed lens using TT. Figure 1(b) and (c) show the corresponding relation between the reference space and the real space. The quantities with and without primes are those in the real space and the reference space, respectively, throughout the paper. Two triangular regions, B1A1D1 and B1′C1D1′, in real space are spatially translated from B0A0D0 and B0′C0D0′, respectively, in the reference space. The thermal materials in these two regions are still the same as the background medium due to the spatial translational transformation. The middle region (i.e. Region V) and the shelled regions (i.e. regions I–IV) are compressed and stretched, respectively, from the real space to the reference space. The whole coordinate transformation can be summarized as:
where and . As shown in Fig. 1(c), a, b and d determine the geometrical size of our shell in the real space. Note that sgn is the sign function, which is defined by:
The thermal conductivity in each region can be calculated with the help of TT15. Only the regions I–V in Fig. 1(a) or (c) have thermal conductivity different from the background medium (i.e. other regions without labels) with a constant isotropic thermal conductivity κ0. The required thermal conductivity in the region V is given by:
The required thermal conductivity in the other four regions I–IV can be summarized by:
where and . The distance between the two triangular regions B1A1D1 and B1′C1D1′ in the real space is d, which is also the thickness of the region V. The function of the whole coordinate transformation (i.e. the effect of the transformation medium) is to shorten the effective distance between these two regions. Actually, the effective distance between these two regions is d0 if the other regions I–V are filled by our lens described by Eqs (3) and (4). Since the effective distance between the two triangular regions is shortened (e.g. d0 « d), the cooling effect would be improved if we set a hot source and a cold source at any position in these two triangular regions, separately.
We use Dr to indicate the real distance between the hot and cold sources, which includes the distance from the two sources to the edge of region V and the physical thickness of region V (see Fig. 1(a)). Since the function of our lens is to shorten the effective distance between the two triangular regions B1A1D1 and B1′C1D1′ (i.e. the thickness of region V), the effective distance between the hot and cold sources are De = Dr − d + d0.
Results
Numerical simulations are given for a hot point source (375 K) and a cold point source (275 K) separated by a fixed distance Dr = 12 cm with and without our lens, respectively, in Fig. 2(a) and (d). The temperature distribution outside our lens is much lower than the case in which the lens is removed, which means that the cooling effect is greatly improved by introducing our lens.
We could expect that if d0 is smaller, the effective spatial distance between the hot source and the cold source is smaller (De = Dr − d + d0), which indicates a better cooling effect. As shown in Fig. 2, the cooling effect improves as d0 becomes smaller while keeping the physical distance between the hot source and the cold source Dr unchanged.
Another interesting aspect is that, if the real distance between the hot source and the cold source is unchanged, and only the parameter d in Eq. (4), which determines the thermal media of our thermal lens, is changed (other parameters a, b, d0 do not change), the performance of our thermal lens also changes. Considering the effective distance between the hot and cold sources are De = Dr − d + d0, and thus the larger d, the better cooling effect (see Fig. 3). Note that d cannot be too much larger, given that the geometrical size of the whole lens is fixed (i.e. d/2 + a < b).
Experiment design
Since thermal conductivity in each region of the whole lens is positive, it can be realized by naturally-available materials. We design a feasible thermal lens with layered isotropic thermal materials based on the effective medium theory. The background medium is chosen to be thermal epoxy with a constant thermal conductivity of 3.4 W/(m·K). The size of the lens is chosen as d = 20 cm, d0 = 1 cm, a = 5 cm, b = 20 cm. We use two layered isotropic thermal media to achieve an effective anisotropic thermal conductivity:
where κA and κB are thermal conductivities of two isotropic media. κ\\ and κ⊥ are the effective anisotropic thermal conductivities along and orthogonal to the direction of interface between two isotropic media, respectively. fA and fB are the filling factor of the medium A and the medium B, respectively, which satisfy fA + fB = 1.
For the region V in the middle of our device, we choose copper with thermal conductivity of 394 W/(m·K) as the medium A. κ\\ and κ⊥ are determined by parameters d and d0 (i.e. the real distance and the effective distance between the hot source and the cold source, respectively), and calculated by Eq. (3): κ\\ = 68 and κ⊥ = 0.17. The required filling factor of the medium A and the thermal conductivity of the medium B are two unknown quantities which can be solved from Eq. (5): fA = 17.2% and κB = 0.141 W/(m·K). We can use PVC with thermal conductivity of 0.14 W/(m·K) as the medium B.
For the Regions I, II, III and IV, we only need to design two layered-media in Region I, and media in other regions can be obtained by the symmetry transformation due to the symmetry of the whole lens with respect to the x′ and y′ axes (see the structure in Fig. 4(a)). The direction of the principal axis of the anisotropic medium in Region I can be obtained by diagonalizing the matrix in Eq. (4) 33:
χ-γ system is the local principal axis system, in which the anisotropic thermal conductivity in Eq. (4) can be expressed by a diagonal matrix. For the thermal lens with the same parameters as in Fig. 2, the angle between the x′-axis and χ-axis is θ = 71[deg], and the two principal values of thermal conductivity are 1.6 W/(m·K) and 2.9 W/(m·K) (i.e. κ\\ = 2.9 and κ⊥ = 1.6). We choose bismuth, with thermal conductivity of nearly 8 W/mK, as medium A. By solving Eq. (5), we can obtain the required thermal conductivity of the medium B and the filling factor: κB = 1.275 W/(m·K) and fA = 24.2%. Thus, fused silica with thermal conductivity of 1.32 W/(m·K) can be used as medium B34. The structure of the lens is shown in Fig. 4(a). Numerical simulation results of the lens composed of a two-layered medium are given in Fig. 4(d), which shows good cooling effect compared to the case where the lens is removed in Fig. 4(b).
We should note that the purpose of our design is to cool down the region outside the shell ABCD in Fig. 1(c) by our lens. We only plot the temperature distribution outside the shell in all our simulations (e.g. in Figs 2, 3 and 4). If we add the temperature distribution of other regions (e.g. inside our lens), we have to rescale the colorbar of the figures and consequently it will be hard to see the difference of the temperature distribution outside the shell for the cases with and without the lens from the figures.
Conclusion
By combining spatial translations and compression transformations, we designed a novel thermal lens for a remote cooling function. The hot source and the cold source can be separated by a certain distance while keeping a good cooling effect by applying our thermal lens around them. Based on the effective medium theory, we also design a specific lens composed of a layered isotropic thermal medium that is available in nature. Numerical simulations verify the function of the proposed lens.
Additional Information
How to cite this article: Sun, F. and He, S. Remote cooling by a novel thermal lens with anisotropic positive thermal conductivity. Sci. Rep. 7, 40949; doi: 10.1038/srep40949 (2017).
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Pendry, J. B., Schurig, D. & Smith, D. R. Controlling electromagnetic fields. Science 312, 1780–1782 (2006).
Leonhardt, U. Optical conformal mapping. Science 312, 1777–1780 (2006).
Chen, H., Chan, C. T. & Sheng, P. Transformation optics and metamaterials. Nat. Mater. 9, 387–396 (2010).
Schurig, D. et al. Metamaterial electromagnetic cloak at microwave frequencies. Science 314, 977–980 (2006).
Ergin, T., Stenger, N., Brenner, P., Pendry, J. B. & Wegener, M. Three-dimensional invisibility cloak at optical wavelengths. Science 328, 337–339 (2010).
Chen, X. et al. Macroscopic invisibility cloaking of visible light. Nat. Comm. 2, 176 (2011).
Wang, W. et al. Design of oblate cylindrical perfect lens using coordinate transformation. Opt. Express 16, 8094–8105 (2008).
Sun, F. & He, S. Extending the scanning angle of a phased array antenna by using a null-space medium. Sci. Rep. 4, 6832 (2014).
Chen, H. & Chan, C. T. Transformation media that rotate electromagnetic fields. Appl. Phys. Lett. 90, 241105 (2007).
Chen, H. & Chan, C. T. Electromagnetic wave manipulation by layered systems using the transformation media concept. Phys. Rev. B 78, 054204 (2008).
Chen, H., Hou, B., Chen, S., Ao, X., Wen, W. & Chan, C. T. Design and experimental realization of a broadband transformation media field rotator at microwave frequencies. Phys. Rev. Lett. 102, 183903 (2009).
Rahm, M. et al. Design of electromagnetic cloaks and concentrators using form-invariant coordinate transformations of Maxwell’s equations. Phot. Nano.-Fund. Appl. 6, 87–95 (2008).
Xu, Y., Du, S., Gao, L. & Chen, H. Overlapped illusion optics: a perfect lens brings a brighter feature. New J. Phys. 13, 023010 (2011).
Lai, Y., Ng, J., Chen, H., Han, D., Xiao, J., Zhang, Z. Q. & Chan, C. T. Illusion optics: the optical transformation of an object into another object. Phys. Rev. Lett. 102, 253902 (2009).
Guenneau, S., Amra, C. & Veynante, D. Transformation thermodynamics: cloaking and concentrating heat flux. Opt. Express 20, 8207–8218 (2012).
Han, T. et al. Experimental demonstration of a bilayer thermal cloak. Phys. Rev. Lett. 112, 054302 (2014).
Xu, H., Shi, X., Gao, F., Sun, H. & Zhang, B. Ultrathin three-dimensional thermal cloak. Phys. Rev. Lett. 112, 054301 (2014).
Ma, Y., Lan, L., Jiang, W., Sun, F. & He, S. A transient thermal cloak experimentally realized through a rescaled diffusion equation with anisotropic thermal diffusivity. NPG Asia Mater. 5, e73 (2013).
Han, T., Yuan, T., Li, B. & Qiu, C. W. Homogeneous thermal cloak with constant conductivity and tunable heat localization. Sci. Rep. 3, 1593 (2013).
Hu, R., Wei, X., Hu, J. & Luo, X. Local heating realization by reverse thermal cloak. Sci. Rep. 4, 3600 (2014).
Han, T. et al. Manipulating steady heat conduction by sensu-shaped thermal metamaterials. Sci. Rep. 5, 10242 (2015).
Han, T. & Gao, Y. Transformation-Based Flexible Thermal Hose with Homogeneous Conductors in Bilayer Configurations. Progress In Electromagn . Res. Lett. 59, 137–143 (2016).
Guenneau, S. & Amra, C. Anisotropic conductivity rotates heat fluxes in transient regimes. Opt. Express 21, 6578–6583 (2013).
Li, Y. et al. Temperature-dependent transformation thermotics: From switchable thermal cloaks to macroscopic thermal diodes. Phys. Rev. Lett. 115, 195503 (2015).
He, X. & Wu, L. Illusion thermodynamics: A camouflage technique changing an object into another one with arbitrary cross section. Appl. Phys. Lett. 105, 221904 (2014).
Hou, Q., Zhao, X., Meng, T. & Liu, C. Illusion thermal device based on material with constant anisotropic thermal conductivity for location camouflage. Appl. Phys. Lett. 109, 103506 (2016).
Zhu, N. Q., Shen, X. Y. & Huang, J. P. Converting the patterns of local heat flux via thermal illusion device. AIP Adv. 5, 053401 (2015).
Chen, T. H., Yang, F. & Mei, Z. L. A simple and flexible thermal illusion device and its experimental verification. Phys. Status Solidi A 212, 1746–1750 (2015).
Han, T., Bai, X., Thong, J. T., Li, B. & Qiu, C. W. Full control and manipulation of heat signatures: Cloaking, camouflage and thermal metamaterials. Adv. Mater. 26, 1731–1734 (2014).
Liu, Y., Jiang, W., He, S. & Ma, Y. An efficient plate heater with uniform surface temperature engineered with effective thermal materials. Opt. Express 22, 17006–17015 (2014).
Liu, Y., Sun, F. & He, S. Novel thermal lens for remote heating/cooling designed with transformation optics. Opt. Express 24, 5683–5692 (2016).
Sun, L. K., Yu, Z. F. & Huang, J. Design of plate directional heat transmission structure based on layered thermal metamaterials. AIP Adv. 6, 025101 (2016).
Sun, F. & He & S. D. C. magnetic concentrator and omnidirectional cascaded cloak by using only one or two homogeneous anisotropic materials of positive permeability. Prog. Electromagn. Res. 142, 683–699 (2013).
Weast, R. C. Handbook of chemistry and physics. Am. J. Med. Sci. 257, 423 (1969).
Acknowledgements
This work is partially supported by the National Natural Science Foundation of China (Nos 91233208, 11621101 and 60990322), the National Natural Science Foundation of China for Young Scholars (No. 11604292), the National High Technology Research and Development Program (863 Program) of China (No. 2012AA030402), the Program of Zhejiang Leading Team of Science and Technology Innovation, the Postdoctoral Science Foundation of China (No. 2013M541774), the Preferred Postdoctoral Research Project Funded by Zhejiang Province (No. BSH1301016) the National Natural Science Foundation of Zhejiang Province (No. Y14F010075) and Swedish VR grant (#621-2011-4620).
Author information
Authors and Affiliations
Contributions
F.S. did calculations, and made simulations. F.S. and S.H. wrote the article and revised it together. S.H. supervised this study and finalized the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Sun, F., He, S. Remote cooling by a novel thermal lens with anisotropic positive thermal conductivity. Sci Rep 7, 40949 (2017). https://doi.org/10.1038/srep40949
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep40949
- Springer Nature Limited
This article is cited by
-
Thermal Lensing Effect in Laser Nanofluids Based on Poly (aniline-co-ortho phenylenediamine)@\(\text{TiO}_{2}\) Interaction
Journal of Electronic Materials (2021)
-
Three-dimensional illusion thermal device for location camouflage
Scientific Reports (2017)