Abstract
In this paper, the periodic double-layer graphene ribbon arrays placed near a metallic ground plate coated by a dielectric layer are proposed and analyzed by the coupled-mode theory (CMT) to predict the perfect absorption response in the mid-infrared region. Numerical simulations of the finite-difference time-domain (FDTD) method confirm this effect and give the underlying physical origin. The anti-symmetric dipole-dipole coupling mode is supported by the double-layer graphene ribbons and acts as the electrical resonance to suppress the reflection, because of the impedance matching. The transmission from this system is restricted by the ultra-thick metallic ground plate. All incident electromagnetic energy is efficiently confined in the interlayer between graphene ribbons and the metallic plate, and the dramatic narrowband perfect absorption peak with the FWHM (full width at half maximums) of 300 nm hence is achieved. The spectral position of the absorption peak can be dynamically tuned by a small change in the chemical potential of graphene, in addition to varying geometrical parameters of the absorber. Meanwhile, this device exhibits good absorption stability over a wide angle range of incidence around ± 60° at least. Such absorber will benefit the fabrication of mid-infrared nano-photonic devices for optical filtering and storage.
Similar content being viewed by others
Introduction
Over the past decades, an extensive amount of research has been carried out on the metamaterials1,2 with unit cells on the sub-wavelength scale in virtue of the growing number of practical applications in the invisibility cloaking3, negative index of refraction4, and perfect lensing5. The metallic ribbons6, cut wire pairs7, and split ring resonators8 have been proposed to predict and enrich the metamaterial theory9,10. Various exotic features that are unavailable in nature have been achieved. Metamaterial perfect absorbers11,12, as an important branch of metamaterials, have attracted considerable attention currently, because the inevitable losses in metallic plasmonic nanostructures can be put to advantages for this research area. In order to realize near-unity absorption, the reflectance is suppressed by matching the effective impedance of the metamaterial to that of the incident medium. Simultaneously, the transmittance is eliminated via maximizing the metamaterial losses, for example, by introducing another metallic plate acting as the substrate13. So far, based on this mechanism, metamaterial near-unity absorbers with electrical resonators including metallic disks14, strips15,16, crosses10, and L-shaped structures17 have been designed and investigated comprehensively. By combining multiple resonators with different sizes together to form a super unit cell, the multi-channel or broadband perfect absorbers have also been achieved18,19,20,21. In addition, the method of the stack multilayer of resonators with different geometric parameters separated by dielectric layers has been used to realize the multi-channel or broadband absorption peaks22,23. However, in order to tune the spectral position of the absorption peak, only the passive method of changing structural parameters of metamaterials is utilized in the most cases. In the practical applications, the method of re-fabricating new structures is unavoidable to change the dimensions of metal-based metamaterial absorbers and further tune the wavelength of the absorption peak. Hence, it is still urgently required to introduce the suitable material into metamaterial absorbers to achieve the active tunability, such as the continuous tuning of the absorption frequency.
Recently, graphene24,25, the first truly two-dimensional material to be observed and isolated in nature, is a single layer of carbon atoms gathered in a honeycomb lattice. Because of the unique electronic band structure that the energy-momentum relation for electrons is liner over a wide range of energies rather than quadratic26, graphene exhibits many exotic optical features including extreme field confinement, low damping losses, and advantageous tunability27,28,29. Additionally, the well-known surface plasmon polaritons (SPPs), sub-wavelength localized electromagnetic waves, are supported by the graphene in the mid-infrared region30,31,32,33. More importantly, graphene owns the original gate-voltage-dependent optical feature34,35 that the chemical potential of graphene can be changed by means of external gate voltages. Graphene-based SPP waves hence can be engineered conveniently by using external gate voltages to vary the surface conductivity of graphene in real-time36, without changing structural dimensions of devices, because the surface conductivity of graphene depends on the chemical potential. This gate-voltage method is preferable for realizing the tunability instead of directly re-fabricating a new structure, as would be needed for metallic devices. Therefore, graphene is emerging as a possible platform for new-generation electrically controlled nano-plasmonic devices. The introduction of graphene will opens up an opportunity to obtain active frequency tuning for metamaterial absorbers.
Currently, a great diversity of graphene-based metamaterials37,38,39 have been devised for enhancing optical absorption, such as, graphene discs40, ribbons41, rings42, even the monolayer graphene coated by metallic gratings43. Herein, we propose a wide-angle plasmonic narrowband perfect absorber based on the periodic double-layer graphene ribbon arrays separated from a metallic ground plate by an ultra-thick dielectric layer. The versatile CMT is applied to predict the perfect absorption response. The FDTD simulation is utilized to reveal the underlying physics and investigate comprehensively the proposed perfect absorber. Simulation results exhibits that the anti-symmetric dipole-dipole coupling resonance in double-layer graphene ribbons acts as the electrical resonance to suppress the reflection, due to the impedance matching. The ultra-thick metallic substrate is used for restricting the transmission. The incident electromagnetic energy is efficiently confined in the interlayer between graphene ribbons and the metallic plate. The outstanding perfect absorption peak with the FWHM of 300 nm is obtained. In addition to varying geometrical parameters of the absorber, a small change in the chemical potential of graphene can be used for controlling the spectral position of the absorption peak. Meanwhile, this device exhibits good absorption stability over a wide angle range of incidence around ± 60° at least. Such absorber will benefits the fabrication of nanophotonic devices and plays an important role in mid-infrared optical filtering and storage.
Results
First, the structure of the proposed absorber composed of the periodic double-layer graphene ribbon array placed near a metallic ground plate coated by a dielectric layer is depicted schematically in the Fig. 1. The x-y cross-section of this device with the corresponding geometrical description is shown in the inset. The double-layer graphene ribbons with identical width of W are separated by the silica layer with the thickness of d. The period of the ribbons array is P. The cavity between the metallic ground plate and the lower graphene layer is filled also by the silica layer with thickness of D. The thickness of the metallic ground plate is H. When the plane wave with the polarization along the x axis irradiates normally this structure, the second-order dipole resonance should form on the single graphene ribbon44. For the double-layer graphene ribbons with a small separation of d = 50 nm, the anti-symmetric plasmonic dipole-dipole coupling resonance45 should form based on the near-field coupling. The transmission from the whole structure is very close to zero (T = 0), as the thickness of the metallic ground plate with H = 800 nm is much larger than the penetration depth of electromagnetic waves. When the double-layer graphene ribbons are considered as a whole and called the anti-symmetric dipole-dipole coupling resonator, the proposed device behaves as such construction of the single port coupled with a resonator. The versatile CMT46,47,48 can illustrate very adequately the property of this configuration.
Schematic of the graphene-based perfect absorber and the incident light polarization configuration.
The inset shows the x-y cross-section of the proposed absorber. The periodic double-layer graphene ribbons with the coupling distance d, width W and period P are constructed. The ribbon arrays are separated from an ultra-thick silver ground plate by a silica layer with thickness D. The thickness of the silver substrate is H.
As shown in the inset of Fig. 1, the amplitudes of the normalized incoming and outgoing waves transmitted through the port are depicted as S+, and S−, respectively. The resonant frequency of the anti-symmetric dipole-dipole coupling mode formed between double-layer graphene ribbons is ω0. The dissipative and radiative losses occurring in the anti-symmetric coupling resonator are represented by τa−1 and τr−1, respectively. The coupling strength between the incident wave and the anti-symmetric resonator is characterized by τc−1. When the incident wave with the frequency ω is launched into this system, the time-evolution-normalized amplitude of the anti-symmetric dipole-dipole coupling resonator is expressed as
![](http://media.springernature.com/lw308/springer-static/image/art%3A10.1038%2Fsrep36651/MediaObjects/41598_2016_Article_BFsrep36651_Equ1_HTML.gif)
Thanks to the power conservation and time reversal symmetry, the relationship between the amplitudes of the normalized incoming and outgoing waves transmitted through the only port is described as
![](http://media.springernature.com/lw175/springer-static/image/art%3A10.1038%2Fsrep36651/MediaObjects/41598_2016_Article_BFsrep36651_Equ2_HTML.gif)
Here, the r0 is the reflectance of this system without the double-layer graphene ribbon array. Because the metallic ground plate behaves as a mirror, all incident waves will be reflected directly at the upper surface of the metallic plate. Therefore, we can obtain r0 = −1. j stands for the imaginary unit. Isolating the S−/S+ and going to the frequency domain e+ jωt, the reflectance of the device can be obtained and expressed as
![](http://media.springernature.com/lw314/springer-static/image/art%3A10.1038%2Fsrep36651/MediaObjects/41598_2016_Article_BFsrep36651_Equ3_HTML.gif)
The impedance of this system can be defined as 15. As this system owns only one anti-symmetric coupling resonator formed between double-layer graphene ribbons, the Lorentzian-shaped resonance should have the minimum at ω = ω0 for the reflection spectrum. At the ω = ω0, the effective impedance of this system is
. If the effective impedance of this system matches to that of the free space (z0 = 1), the radiative losses can be neglected, corresponding to τr−1 ≈ 0. Hence, only the condition of τa−1 = τc−1 should be satisfied. At the ω = ω0, the impedance matching is realized and r = 0. Thus, the absorption is A = 1 − T − |r|2 = 1. In other word, the perfect absorption response will be achieved at the ω = ω0.
The reflection of this system is
![](http://media.springernature.com/lw312/springer-static/image/art%3A10.1038%2Fsrep36651/MediaObjects/41598_2016_Article_BFsrep36651_Equ4_HTML.gif)
The absorption of this structure can be given by
![](http://media.springernature.com/lw350/springer-static/image/art%3A10.1038%2Fsrep36651/MediaObjects/41598_2016_Article_BFsrep36651_Equ5_HTML.gif)
The CMT predicted absorption spectrum is shown in Fig. 2(a), and marked by the red line. Here, τa−1 = τc−1 = 1*1012 Hz are considered for obtaining a useful impedance matching. The resonant wavelength λ0 = 2πc/ω0 is assumed as 11.16 μm, here c is the velocity of light in vacuum. Obviously, the perfect absorption feature occurs. In order to confirm the CMT-predicted perfect absorption response and further investigate comprehensively the proposed absorber, the numerical simulation is performed by the Lumerical FDTD Solutions.
Absorption spectra and electromagnetic field distributions of the graphene-based device.
(a) Absorption spectra obtained by the CMT and FDTD simulation. The inset illustrates the electric field (Ey) distributions of the unit-cell double-layer graphene ribbons at the resonant wavelength of λ0 = 11.16 μm. (b) Magnetic field (Hz) distributions of the entire unit cell at wavelengths of λ0 = 11.16 μm and λ = 14.00 μm, respectively.
In the numerical calculations, the graphene ribbon is modeled as an ultra-thin film with a thickness of Δ (in the y direction). The surface conductivity (σg) of the graphene is governed by the Kubo formula49,50 that depends on the momentum relaxation time τ, temperature T, chemical potential μc, and incident wavelength λ (frequency ω). At the room temperature and for the highly doped graphene in the simulated mid-infrared spectral range, the chemical potential is always above half of the photon energy. The Kubo equation hence is reduced to51 , where the intraband transition dominates and the interband transition is neglected. The equivalent permittivity of graphene is calculated by the equation52:
, where
(≈377 Ω) is the intrinsic impedance of vacuum, and
. The thickness of the monolayer graphene is assumed to be Δ = 1 nm which is reasonable, although its real thickness is 0.34 nm. Because the equivalent permittivity εeq of graphene is thickness-dependent52, the different values of the Δ will give rise to the corresponding equivalent permittivity and these extremely small values of the thickness can lead to similar simulation results. The chemical potential of graphene is assumed first to be μc = 0.4 eV, and the momentum relaxation time is chosen as τ = 0.5 ps. The metal is chosen as the silver with the dispersive permittivity characterized by the Drude model53,54,55
. Here, ε∞ = 3.7 is the dielectric constant at infinite angular frequency; ωp = 9.1 eV is the bulk plasma frequency representing the natural frequency of the oscillations of free conduction electrons; γ = 0.018 eV stands for the damping frequency of the oscillations. In the considered mid-infrared region, the silica is assumed to be a non-dispersive dielectric with the index of 1.45. The unit cell with P = 300 nm, W = 150 nm, and D = 600 nm is performed. Periodic boundary conditions are applied along the y directions and perfectly matched layers are employed in the x direction. A plane wave with the electric field parallel to the x axis illuminates normally the periodic structure. We use the non-uniform mesh, and the minimum mesh size inside the graphene layer equals 0.1 nm and gradually increases outside the graphene sheet, for saving storage space and computing time. 2D-FDTD simulated results are presented in Fig. 2.
In the Fig. 2(a), the simulated absorption spectrum indicated by the blue curve is shown and the perfect absorption peak with the resonant wavelength of λ0 = 11.16 μm appears distinctly. The FWHM of the absorption peak is 300 nm. Simulated results indeed confirm that the perfect narrowband absorber can be achieved by the proposed graphene-based structure. The simulated phenomenon is agreement with that predicted by the CMT. The electric field Ey distributions of the unit-cell double-layer graphene ribbons at the resonant wavelength of λ0 = 11.16 μm are displayed in the inset. Obviously, the second-order dipole resonance is supported by the single graphene ribbon. When the double-layer graphene ribbons are considered as a whole, the anti-symmetric plasmonic dipole-dipole binding indeed forms based on the near-field coupling. The entire structure of graphene ribbons hence acts as an anti-symmetric dipole-dipole coupling plasmonic resonator. The electrical resonance hence occurs at the graphene ribbons and the incident electromagnetic energy is confined and introduced into this system. To better understand the underlying physics of the perfect absorption response, the magnetic field (Hz) distributions of the entire unit cell at wavelengths of λ0 = 11.16 μm and λ = 14.00 μm, are shown in Fig. 2(b). For the resonant wavelength of λ0 = 11.16 μm, the electrical resonance yields at the anti-symmetric coupling plasmonic resonator formed by the double-layer graphene ribbons. The effective impedance of the vertically coupling graphene ribbons matches to that of the free space, and the reflection thus is suppressed. The transmission from this system is also inhibited due to the ultra-thick metallic ground plate. All incident electromagnetic energy is efficiently confined in the silica interlayer between the graphene ribbons and the metallic ground plate. Therefore, the perfect absorption feature is achieved by the simple graphene-based structure. On the contrary, the electrical resonance of the double-layer graphene ribbons and the effective impedance matching condition cannot be formed at the other nor-resonant wavelengths. The most incident power is reflected and cannot be confined by this device, as shown in Fig. 2(b) at the incident wavelength of λ = 14.00 μm.
Now that the spectral position of the perfect absorption peak corresponds to the resonant wavelength of the anti-symmetric coupling dipole-dipole resonator formed on the double-layer ribbons, the change in the resonant wavelength of the anti-symmetric coupling resonator can be utilized to tune the spectral position of the absorption peak. For anti-symmetric coupling dipole-dipole resonator, the changes in the geometrical parameters of double-layer graphene ribbons should have a direct effect on its resonant wavelength. Thus, the changes in the geometrical parameters of graphene ribbons can be used first for tune the spectral position of the absorption peak d = 50 nm and the duty ratio of W/P = 0.5 are fixed. Other structural and material parameters are unchanged. The structure with the simultaneous change in the width W of double-layer ribbons is simulated and results are presented in Fig. 3(a). It is well known that the wavelength of dipole resonance in the single graphene ribbon increases as the ribbon width increases56. So, the absorption peak tends to exhibit a red shift with the ribbon width increase, as shown in Fig. 3(a) where the absorption spectra with ribbon widths of W = 150, 180, 210, and 240 nm are offered. The obvious width-dependent tunability is achieved. In addition, the real part of the wave vector of the anti-symmetric dipole-dipole coupling resonance increases with the vertical coupling distance between ribbons increase45. The resonant wavelength of the absorption peak hence should show a red shift as the coupling distance d increases. Simulated absorption spectra with different coupling distances are displayed in Fig. 3(b) where the other simulated parameters are same as that used in Fig. 2(b). The coupling distance varies from 30 to 70 nm, and the resonant wavelength of the absorption peak increases from 10.45 to 11.61 μm. The coupling-distance-dependent tunability is also confirmed.
In addition, for the absorption peak, the most incident electromagnetic power is confined in the space between the lower graphene ribbon and the metallic ground plate. Hence, the height of the space should have a direct effect on the performance of this absorber. Numerical absorption spectra under different distances D are presented in Fig. 4. Simulated parameters are same to be that used for Fig. 2. According to this color map, it is found that the change in the distance D has little effect on the central wavelength of the absorption peak, whereas influences greatly the absorption and FWHM of the resonant peak. In other word, the absorption spectrum can be modulated by changing the thickness D, without changing the spectral position of the absorption peak. This phenomenon offered by the Fig. 4 can also be well understood. The effective impedance of the period double-layer graphene ribbons depends on the thickness D of the silica space41. As the thickness D increases from 50 to 600 nm, the perfect impedance matching to that of the free space is formed gradually. With the thickness D increase further, the perfect impedance matching is broken. Hence, the perfect absorber is achieved first and then is hampered with the increase of the thickness D. On the other hand, the anti-symmetric dipole-dipole coupling plasmonic resonance in double-layer graphene ribbons is localized around the graphene ribbons with deep sub-wavelength nano-scales, which are less than 50 nm as shown in the inset of Fig. 2(a). The change in the thickness of the dielectric layer from 50 to 1000 nm hence has no effect on the resonant wavelength of the anti-symmetric dipole-dipole coupling resonator. The spectral position of the absorption peak is kept unchanged as the thickness D increases from 50 to 1000 nm.
Besides the geometrical tunability, the graphene-based absorber is particular to own the novel gate-voltage-dependent feature that the chemical potential of graphene can be dynamically tuned by applying external gate voltages, as shown in Fig. 1 where the two external gates may be used for controlling the chemical potential. Without re-fabricating a new structure, only a small change in the chemical potential of graphene can vary the plasmonic resonant wavelength because the surface conductivity of graphene depends directly on the chemical potential. Here, the effect of the change in chemical potentials of double-layer graphene ribbons on the spectral position of the absorption peak is calculated numerically. Simulated absorption spectra with chemical potentials of μc = 0.35, 0.4, 0.45, and 0.5 eV, respectively, are shown in Fig. 5. Other simulation parameters are same as that in Fig. 2(b). A comparison of four curves indicates that the resonant wavelength of absorption peak shifts to a shorter wavelength with an increase of the chemical potential. It is mainly because that the real part of the wave vector of the anti-symmetric dipole-dipole coupling resonance decreases as the chemical potential increases56. In addition, it is clear that the absorption at the resonant peak decreases gradually as the chemical potential increases. It owes to that the impedance matching is broken when the chemical potential increases. The reflection cannot be suppressed completely. However, in the considered range of the chemical potential, the absorption is always larger than 90%. Hence, the chemical-potential-dependent tunability is obtained.
It should be pointed out that the electromagnetic waves irradiate usually this absorber with an oblique incident angle in the practical applications. Thus, it is necessary to investigate the robustness of the proposed perfect absorber under the oblique incidence. Other simulation parameters are similar to that in Fig. 2(b). Further simulations with nor-normal incident angles are performed, and the absorption as a function of wavelength and the angle of incidence is displayed in Fig. 6. Based on this color map, it is obvious that the spectral position of the absorption peak nearly keeps unchanged over a wide angle range of incidence around ± 60°. At the same time, the narrowband absorption (great than 85%) is not limited to the normal incident angle but extended to at least 60°. Hence, the designed narrowband absorber operates well over a wide range of the angle of incidence, and the wide-angle graphene-based absorber is obtained.
Discussion
To sum up, the periodic double-layer graphene ribbon arrays placed on a metallic ground plate coated by a dielectric space are proposed and investigated both numerically and theoretically. The well-known CMT is used for analyzing the structural property and predicting the perfect absorption feature. FDTD numerical simulation is utilized to give the underlying physics. Simulated results exhibit that the localized anti-symmetric dipole-dipole coupling modes occurs at double-layer graphene ribbons and acts as the electrical resonance to suppress the reflection, thanks to the impedance matching. The ultra-thick metallic ground plate is used for restricting the transmission from this system. The incident electromagnetic energy is efficiently confined in the interlayer between graphene ribbons and the metallic substrate, and the novel perfect absorber hence is achieved. The spectral position of the absorption peak can be dynamically tuned by a small change in the chemical potential, in addition to varying geometrical parameters of the absorber. Meanwhile, this device exhibits good absorption stability over a wide angle range of incidence around ± 60° at least. Such simple plasmonic perfect absorber may benefit the fabrication of nanophotonic devices for optical filtering and storage in the mid-infrared region.
Methods
Numerical simulations
The 2D finite-difference time-domain (FDTD) method is used for the numerical simulation and the commercial software of Lumerical FDTD Solutions is performed. Periodic boundary conditions are applied along the y directions and perfectly matched layers are employed in the x direction. A plane wave with the electric field parallel to the x axis illuminates normally the periodic structure. The non-uniform mesh is adopted, and the minimum mesh size inside the graphene layer equals 0.1 nm and gradually increases outside the graphene sheet, for saving storage space and computing time.
Additional Information
How to cite this article: Li, H. et al. Tunable graphene-based mid-infrared plasmonic wide-angle narrowband perfect absorber. Sci. Rep. 6, 36651; doi: 10.1038/srep36651 (2016).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Shelby, R. A., Smith, D. R. & Schultz, S. Experimental verification of a negative index of refraction. Science 292, 77–79 (2001).
Jahani, S. & Jacob, Z. All-dielectric metamaterials. Nat. Nanotechnol. 11, 23–36 (2016).
Cai, W. et al. Optical cloaking with metamaterials. Nat. Photonics 1, 224–227 (2007).
Smith, D. R. et al. Composite medium with simultaneously negative permeability and permittivity. Phys. Rev. Lett. 84, 4184 (2000).
Pendry, J. B. Negative refraction makes a perfect lens. Phys. Rev. Lett. 85, 3966 (2000).
Diem, M., Koschny, T. & Soukoulis, C. M. Wide-angle perfect absorber/thermal emitter in the terahertz regime. Phys. Rev. B 79, 033101 (2009).
Yao, Y. et al. High-responsivity mid-infrared graphene detectors with antenna-enhanced photocarrier generation and collection. Nano Lett. 14, 3749–3754 (2014).
Tao, H. et al. Highly flexible wide angle of incidence terahertz metamaterial absorber: Design, fabrication, and characterization. Phys. Rev. B 78, 241103 (2008).
Chen, W. C. et al. Role of surface electromagnetic waves in metamaterial absorbers. Opt. Express 24, 6783–6792 (2016).
Chen, H. T. Interference theory of metamaterial perfect absorbers. Opt. Express 20, 7165–7172 (2012).
Watts, C. M., Liu, X. & Padilla, W. J. Metamaterial electromagnetic wave absorbers. Adv. Mater. 24, OP98 (2012).
Landy, N. I. et al. Perfect metamaterial absorber. Phys. Rev. Lett. 100, 207402 (2008).
Liu, X. et al. Infrared spatial and frequency selective metamaterial with near-unity absorbance. Phys. Rev. Lett. 104, 207403 (2010).
Liu, N. et al. Infrared perfect absorber and its application as plasmonic sensor. Nano Lett. 10 2342–2348 (2010).
Wu, C. et al. Large-area wide-angle spectrally selective plasmonic absorber. Phys. Rev. B 84, 075102 (2011).
Avitzour, Y., Urzhumov, Y. A. & Shvets, G. Wide-angle infrared absorber based on a negative-index plasmonic metamaterial. Phys. Rev. B 79, 045131 (2009).
Bai, Y. et al. Wide-angle, polarization-independent and dual-band infrared perfect absorber based on L-shaped metamaterial. Opt. Express 23, 8670–8680 (2015).
Hu, C. et al. Mixed plasmons coupling for expanding the bandwidth of near-perfect absorption at visible frequencies. Opt. Express 17, 16745–16749 (2009).
Ma, Y. et al. A terahertz polarization insensitive dual band metamaterial absorber. Opt. Lett. 36, 945–947 (2011).
Yao, G. et al. Dual-band tunable perfect metamaterial absorber in the THz range. Opt. Express 24, 1518–1527 (2016).
Shen, X. et al. Polarization-independent wide-angle triple-band metamaterial absorber. Opt. Express 19, 9401–9407 (2011).
Ye, Y. Q., Jin, Y. & He, S. Omnidirectional, polarization-insensitive and broadband thin absorber in the terahertz regime. JOSA B 27, 498–504 (2010).
Liu, S., Chen, H. & Cui, T. J. A broadband terahertz absorber using multi-layer stacked bars. Appl. Phys. Lett. 106, 151601 (2015).
Bonaccorso, F., Sun, Z., Hasan, T. & Ferrari, A. Graphene photonics and optoelectronics. Nat. Photonics 4, 611–622 (2010).
Geim, A. K. & Novoselov, K. S. The rise of graphene. Nat. Mater. 6, 183–191 (2007).
Garcia de Abajo, F. J. Graphene plasmonics: challenges and opportunities. ACS Photonics 1, 135–152 (2014).
Nikitin, A. Y. et al. Edge and waveguide terahertz surface plasmon modes in graphene microribbons. Phys. Rev. B 84, 161407 (2011).
Ju, L. et al. Graphene plasmonics for tunable terahertz metamaterials. Nat. Nanotechnol. 6, 630–634 (2011).
Lu, H. et al. Graphene-based active slow surface plasmon polaritons. Sci. Rep. 5, 8443 (2015).
Grigorenko, A. N., Polini, M. & Novoselov, K. S. Graphene plasmonics. Nat. Photonics 6, 749–758 (2012).
Koppens, F. H., Chang, D. E. & Garcia de Abajo, F. J. Graphene plasmonics: a platform for strong light–matter interactions. Nano Lett. 11, 3370–3377 (2011).
Li, H. J. et al. Tunable mid-infrared plasmonic band-pass filter based on a single graphene sheet with cavities. J. Appl. Phys. 116, 224505 (2014).
Li, H. J. et al. Investigation of the graphene based planar plasmonic filters. Appl. Phys. Lett. 103, 211104 (2013).
Chen, J. et al. Optical nano-imaging of gate-tunable graphene plasmons. Nature 487, 77–81 (2012).
Fei, Z. et al. Gate-tuning of grapheneplasmons revealed by infrared nano-imaging. Nature 487, 82–85 (2012).
Fang, Z. et al. Gated tunability and hybridization of localized plasmons in nanostructured graphene. ACS Nano 7, 2388–2395 (2013).
Hu, X. & Wang, J. High-speed gate-tunable terahertz coherent perfect absorption using a split-ring graphene. Opt. Lett. 40, 5538–5541 (2015).
Xiong, F. et al. Ultrabroadband, More than One Order Absorption Enhancement in Graphene with Plasmonic Light Trapping. Sci. Rep. 5, 16998 (2015).
Zhang, Y. et al. Graphene based tunable metamaterial absorber and polarization modulation in terahertz frequency. Opt. Express 22, 22743–22752 (2014).
Thongrattanasiri, S., Koppens, F. H. & de Abajo, F. J. G. Complete optical absorption in periodically patterned graphene. Phys. Rev. Lett. 108, 047401 (2012).
Jang, M. S. et al. Tunable large resonant absorption in a midinfrared graphene Salisbury screen. Phys. Rev. B, 90, 165409 (2014).
He, X. Tunable terahertz graphene metamaterials. Carbon 82, 229–237 (2015).
Mason, J. A., Smith, S. & Wasserman, D. Strong absorption and selective thermal emission from a midinfrared metamaterial. Appl. Phys. Lett. 98, 241105 (2011).
Nikitin, A. Y. et al. Edge and waveguide terahertz surface plasmon modes in graphene microribbons. Phys. Rev. B 84, 161407 (2011).
Christensen, J. et al. Graphene plasmon waveguiding and hybridization in individual and paired nanoribbons. ACS Nano 6, 431–440 (2011).
Haus, H. A. & Huang, W. P. Coupled-mode theory. Proc. IEEE 79, 1505–1518 (1991).
Rosolen, G. & Maes, B. Graphene ribbons for tunable coupling with plasmonic subwavelength cavities. JOSA B 31, 1096–1102 (2014).
Li, H., Wang, L., Zhang, B. & Zhai, X. Tunable edge-mode-based mid-infrared plasmonically induced transparency in the coupling system of coplanar graphene ribbons. Appl. Phys. Express 9, 012001 (2015).
Chen, P. Y. & Alu, A. Atomically thin surface cloak using graphene monolayers. ACS Nano 5, 5855–5863 (2011).
Hanson, G. W. Dyadic Green’s functions and guided surface waves for a surface conductivity model of graphene. J. Appl. Phys. 103, 064302 (2008).
Wang, B., Zhang, X., Yuan, X. & Teng, J. Optical coupling of surface plasmons between graphene sheets. Appl. Phys. Lett. 100, 131111 (2012).
Vakil, A. & Engheta, N. Transformation optics using graphene. Science 332, 1291–1294 (2011).
Park, J., Kim, H. & Lee, B. High order plasmonic Bragg reflection in the metal-insulator-metal waveguide Bragg grating. Opt. Express 16, 413–425 (2008).
Chen, Z. et al. Symmetry breaking induced mode splitting based on a plasmonic waveguide system. J. Phys. D: Appl. Phys. 49, 145109 (2016).
Zhan, S. et al. Tunable nanoplasmonic sensor based on the asymmetric degree of Fano resonance in MDM waveguide. Sci. Rep. 6, 22428 (2016).
Vasić, B., Isić, G. & Gajić, R. Localized surface plasmon resonances in graphene ribbon arrays for sensing of dielectric environment at infrared frequencies. J. Appl. Phys. 113, 013110 (2013).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Grant Nos 61505052, 11074069, 61176116), and Hunan Provincial Innovation Foundation for Postgraduate (Grant No. CX2015B068).
Author information
Authors and Affiliations
Contributions
H.J.L. conceived the idea, carried out the numerical simulations and wrote the first draft of manuscript text. L.L.W. and X.Z. discussed the design of the proposed device and simulation results, as well as improved the manuscript presentation.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Li, H., Wang, L. & Zhai, X. Tunable graphene-based mid-infrared plasmonic wide-angle narrowband perfect absorber. Sci Rep 6, 36651 (2016). https://doi.org/10.1038/srep36651
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep36651
- Springer Nature Limited
This article is cited by
-
Graphene-based electromechanically tunable subwavelength mid-IR perfect absorber
Optical and Quantum Electronics (2023)
-
A Tunable Dual-Band and Polarization-Insensitive Coherent Perfect Absorber Based on Double-Layers Graphene Hybrid Waveguide
Nanoscale Research Letters (2019)
-
Tunable Plasmonic Perfect Absorber Based on a Multilayer Graphene Strip-Grating Structure
Journal of Electronic Materials (2019)
-
A Band Enhanced Tunable Ultra-Broadband Absorber Based on Loading the Lumped Resistors and Cavity Resonance
Plasmonics (2019)
-
Photovoltaic Performance of Pin Junction Nanocone Array Solar Cells with Enhanced Effective Optical Absorption
Nanoscale Research Letters (2018)