Abstract
Crack propagation is tracked here with Digital Image Correlation analysis in the test case of two cracks propagating in opposite directions in polycarbonate, a material with high ductility and a large Fracture Process Zone (FPZ). Depending on the initial distances between the two crack tips, one may observe different complex crack paths with in particular a regime where the two cracks repel each other prior to being attracted. We show by strain field analysis how this can be understood according to the principle of local symmetry: the propagation is to the direction where the local shear - mode KII in fracture mechanics language - is zero. Thus the interactions exhibited by the cracks arise from symmetry, from the initial geometry, and from the material properties which induce the FPZ. This complexity makes any long-range prediction of the path(s) impossible.
Similar content being viewed by others
Introduction
Fracture is a quintessential cross-disciplinary problem, in that what happens in materials on the atomistic scale becomes important at the macroscopic scale. The understanding of crack dynamics and stability has made enormous progress due to practical approaches to computational structural mechanics and materials design for stability. On the fundamental side, advances have been made e.g. in atomistic first principles simulations, and basic experiment using various techniques to follow slow and fast fracture, and also to analyze a posteriori the question “what happened”.
The coarse-grained approach of fracture mechanics seeks an answer by solving the elasticity problem for a specimen under loading, and then postulating a criterion for the stability of a defect - a crack or a notch in a prepared experiment. An example of this is the Griffith’s argument that connects the crack advancement to the fracture toughness of a material by comparing the elastic energy released by crack propagation to the energy dissipated by new crack surface formation. This illustrates in a simple fashion how the macroscopic material properties and predictability connect physics at lower scales. The original idea has been extended to ductile (Dugdale-Irwin-Barenblatt argument) and quasi-brittle materials, both of which introduce a length-scale, the size of the so-called Fracture Process Zone (FPZ) that arises by coarse-grained processes from a smaller scale.
Real materials are rarely extremely brittle, which means that cracks grow and interact, before the change to unstable dynamics takes place. The paradigm for the propagation has been for a long while that of “local symmetry”. This means according to Linear Elastic Fracture Mechanics (LEFM) selecting the direction where the stress intensity factor KII = 0, or the shear stresses vanish1. This equals the criterion of the maximum tangential strain, MTSN, known from the 70’s2. The MTSN criterion is based on the St. Venant’s maximum normal strain theory. The thought-experiment that one usually does in guessing in a two-dimensional case about where a crack will go equals at looking at the dynamics of a point, the crack tip. Thus one considers the next direction to which the tip will propagate to according to such symmetry principles. In real materials, where LEFM does not hold in general the challenge is to formulate the dynamical law for slowly growing cracks: where does a local symmetry hold, such that it can be used for crack path prediction, in the presence of the FPZ?
Recently the applicability of LEFM in both quasi-static and dynamical crack propagation has been actively studied3,4,5,6,7,8. A major reason is given by advances in image analysis methods e.g. ref. 9. We consider here a paradigm of complexity for interacting cracks: a thin-sheet geometry with two initial notches, Fig. 1, studied recently10. In the LEFM-limit this already presents an interesting case, where the two crack tips exhibit an attraction5. We test samples of polycarbonate sheets. The material has a convenient feature in that one can make a clear distinction of elastic and near-tip plastic regimes11. In the spirit of Dugdale-Irwin theory, we follow the advance of the tips, when we are monitoring the tip of the plastic zone. The experiment (mode I, constant loading velocity, see Materials and Methods) shows consistently that for curved cracks the cracks and the plastic process zones propagate along the direction of maximum tangential strain. In general, there are three regimes that can be identified: the initial one with no interaction (Δ y = 0), repulsion (Δ y > 0) and, finally attraction (Δ y < 0). Interestingly the repulsion starts much before the attraction, in contrast to what is seen in the LEFM or purely elastic material case5. That the two cracks exhibit both initial repulsion and a later attraction is logically consistent with the KII = 0 argument again12,13. A snapshot for a typical experiment is depicted in Fig. 2, at a point in which both the FPZ zones have grown and the cracks are interacting with each other. Figure 2 shows an example of two large plastic zones attracting each other just before sample starts to buckle out of plane. The general situation is shown in Fig. 3, where the trajectories of both cracks are shown in an example.
From Repulsion to Attraction
The turning point (from “away from each other” to “towards each other”) of the cracks gives one measure of the regimes of crack repulsion and attraction. In this paper we test some other measures for the turning point. Figure 4 shows the characteristic times of selected features as a function of initial notch separation distance. The turning time tturn depicted as blue dots is defined as when repulsion turns to attraction
where Δy is the distance between upper and lower FPZ tips. tturn is thus the maximum FPZ tip vertical distance during the experiment. The time of turning correlates with the strain rate maximum in y-direction εyy (Materials and Methods) shown as red triangles and with when maximum tangential strain changes direction (maximum at 0 degree angle) depicted as green circles. For short initial separations the strain measurement indicated turning points either slightly precede or are the same as the optical measurement. For large initial distances, the plastic zones develop naturally and the strain measurement indicate a turning point which precedes the optical one actual turn. Figure 4 thus illustrates the effect of under developed PZ for small L and fully developed PZ for large L. Differences in the Fig. 4 between the grayscale and strain measurements can be explained by FPZ “inertia”. The FPZ does not follow (in how it develops as the crack advances) the natural crack growth path due to the work needed to create the new FPZ in a material with finite viscosity.
The FPZ are repelling each other when measured from grayscale images while the strain is already showing attraction. The FPZ does not turn but does it later. Note that usually in the LEFM -based theories the stress creates the FPZ; We are measuring strain, not directly the stress. In summary, the quantities show some difference which can be explained by how the turning time is defined. The “turning” is a slow process: the FPZ zone of the crack propagating to one direction has to advance a while to the new direction before the maximum y-distance can be observed, see Equation 1, when comparing this that of strain rate, which is an instant measure. In other words, the crack and the FPZ have inertia. The most interesting result in Fig. 4 is the time when MTSN changes direction. This is the time when local symmetry predicts that the crack will change direction. This also coincides with the time when the strain yy-component is at maximum. By definition, and are equal when θ = 0.
Local Symmetry Argument
Next we show in detail that the crack growth direction obeys the local symmetry argument. This argument is usually taken as granted as its roots are in the 1960’s. To be more precise there are a few rigorous treatments to this fundamental property. For a review of growth laws see e.g. refs 14 and 15. In our geometry α is the angle between horizontal axis and crack propagation direction, initially α = 0°, see Fig. 1 for details. Cottrell and Rice1 conclude in their paper that maximum tangential stress (or similar) criteria essentially means that the stress intensity factor KII = 0 at the propagation direction. They note that this holds for small propagation angles α < 15°. This is called the local symmetry argument. It can be also shown that in the case of stationary cracks, the KII component changes sign when the ratio between horizontal and vertical crack distances is changed12. In other words, the shear component sign change is related to the observation of first repulsion and then attraction as the crack propagates. Note that in ref. 12 the crack is static and the KII is measured as when the crack would grow horizontally with α = 0°. We test the more general case as the cracks grow and interact.
Comparison between crack propagation criteria is given by e.g. Maiti et al.2, where four methods are considered: i) maximum tangential stress, ii) maximum tangential strain, iii) maximum tangential principal stress and iv) strain energy density criterion. From their discussion one can conclude that when an angle of a slit crack α ≤ 15°, all methods give the same result for crack propagation angle within 1 degree. The local symmetry argument essentially claims that the FPZ or yield zone will propagate to the direction where Mode II component vanishes or is minimized1. This can be measured by finding the location of maximum tangential strain. As the stress of a homogeneous material is difficult to measure, the approximation is made that the maximum tangential strain criterion estimates the same propagation angle as the maximum tangential stress.
Next we analyze the strain fields for a few cases with different methods showing different propagation angles. First the strain is measured at the circle around the FPZ tip (see Materials and Methods). Second the strain field is depicted at various time steps showing attraction and repulsion for two different geometries. Finally we compare the propagation angles obtained by optical observation (see also ref. 10) and strain measurements. Figure 5 depicts the cross component of the strain tensor εxy similarly to ref. 16, that is the LEFM expression for the component is used to fit the data. The strain is measured on a circle at a 1 mm radius from the FPZ tip. The theoretical line is plotted as if the crack would propagate in 30 degree angle in a repulsion case, that is using a 30 degree offset (rotation). This shift is an example of a very strong repulsion. In the experiments, much less strong repulsion (smaller angles) is observed.
Figure 6a–c depict the tangential strain just at the beginning, repulsion and attraction for experiment with d = 4 cm initial separation. The FPZ tip as the origin is marked with a black cross. Figure 7 shows the same quantity with d = 1 cm initial separation. Figure 8 shows the comparison between maximum tangential strain MTSN and FPZ propagation angle defined from grayscale images. The dotted line shows the path of the maximum tangential strain where the elongation is the greatest along the arc of the circle with FPZ tip as a center. The solid line is the crack propagation angle θ = 0.5 Δy/Δx where Δx and Δy are the horizontal and vertical distances between the two FPZ tips defined from the grayscale images10, computed such that the asymmetry in the tensile test (fixed bottom clamp) is removed. The propagation angle seems always to be a bit less than the maximum strain direction. This is due again to the non-elastic properties of the material as was noted in the context of Fig. 4. This is also consistent with LEFM predictions and propagation angle analysis. When the crack tries to turn more than 15°, more higher order terms are needed and a simple maximum tangential strain estimate fails. That is, the theoretical estimates mentioned above also show that the propagation angles with simple maximum arguments are only valid for small propagation angles.
To recapitulate, cracks tend to propagate along paths where shear strain vanishes: εxy(θ = 0) = 0 and at the simplest one may note that in Fig. 5 the εxy(θ = 0) is positive. This means that the crack is not going to propagate straight but turns towards positive angles (counter clockwise). This is a simple version of a complicated process that is described in detail in ref. 17 where multiple criteria for crack propagation and strain field values are compared in en passant geometry.
Summary
Here, we have shown that the crack propagation direction can be obtained by using optical displacement measurement in thin sheets by considering the strain fields at an appropriate distance ahead of the crack tip and the FPZ. In polycarbonate sheets, FPZ tip zone can be treated as the crack tip and thus the MTSN and local symmetry criteria used. The slightly curved cracks obey the local symmetry argument. The cracks interact, such that the shear deformations affect the respective FPZ, their development, and induce an early-stage - “prior to meeting” - repulsion contrary to the purely elastic case. In materials with heterogeneities and with yielding, we expect that with the same key argument, measuring the Mode II (shear) component, one can provide local estimates of the near-future crack propagation path. This result is of importance in heterogeneous materials due to the memory implied: one can construct a probability map of possible crack propagation directions ahead of the crack/FPZ tip. However, due to the mutual interaction(s) of the two cracks here, the predictability does not extend to beyond a small scale that changes with propagation as it depends on the exact crack and FPZ geometry. An example would be the prediction of the precise point at which the initial repulsion turns into attraction due to the mutual propagation of the cracks and the evolution of the respective FPZ. It would be interesting to repeat these experiments for other materials than polycarbonate, with its large FPZ. One question would indeed be how big a process zone is needed to observe noticeable repulsion.
Materials and Methods
The material used in this study is a polycarbonate sheet of 100 × 120 × 0.13 mm3. The sample is notched from two sides symmetrically with two tunable parameters: horizontal L and vertical d notch distances (Fig. 1). The vertical distance is varied from d = 10 mm to 40 mm and the horizontal distance is varied L = 10, 20, 40, 60, 80 mm. The experiment set is repeated two times, with and without tracers. In the latter case, the transparent sample is painted with inert water based paint. This is to help either the edge detection (no tracers) or digital image correlation algorithm (with tracers). A snapshot (Fig. 1) shows the sample geometry. Initial notches are depicted with red. β is the angle between the applied tension and initial notches. α is the complement of beta. θ refers to the angle of the propagating plastic zone respect to horizontal axis.
The sample is attached to a standard tensile testing machine, Instron Electropuls 1000. Figure 1 depicts the orientation of the sample is such that the primary stress and strain are perpendicular to the notches. The effective testing plane is 100 × 100 mm2 due to 10 mm material reserved for clamping on top and bottom. The testing machine imposes a constant displacement speed of v = 0.02 mm/s for the upper crosshead. The machine stores the force-displacement data with a frequency of f = 500 Hz. The images are recorded by a standard digital grayscale camera Dalsa HM1024. The analysis of the experimental data relays on three methods. First the standard force-displacement data is obtained from the tensile testing machine. Second, the plastic zone tip location is obtained from conventional image analysis (see ref. 10 and references therein). Finally the displacement field is obtained using digital image correlation algorithm (DIC)19,20,21,22. The algorithm and its accuracy is explained in detail in ref. 23 and is used also in ref. 24.
The DIC algorithm compares two gray scale images together and calculates a displacement map between the two images. The algorithm at hand uses 2 dimensional 3rd degree b-splines for the mapping with one node in a 32 × 32 pixel (0.3 × 0.3 mm) region interest. In a smooth linear deformation near the crack tip a 0.1 pixel (1 μm) accuracy is a good starting point. In the case of strain, a 0.1 pixel displacement in a 32 pixel distance corresponds to a strain accuracy of 0.3% which is used here. Increasing the derivation lag increases the accuracy but decreases the resolution.
The measured peak strain at the FPZ tip is around 0.9% in a 1 mm region in a 2-second time window. With this rate the material has reached its yield strain in 5 seconds. This coincides with the 5% yield strain of polycarbonate and average FPZ propagation speed of 0.2 mm/s. In a 100-second experiment the FPZ has propagated 20 mm corresponding roughly to the observed behavior.
The tangential strain (or hoop strain) ref. 25 is a numerical derivative of displacement along the circular arc with FPZ as center. Cartesian displacements are obtained from the mentioned digital image correlation algorithm. In this paper strain is measured in a time window of tstrain = 2 s. We use the word strain instead of strain rate because of simplicity.
Additional Information
How to cite this article: Koivisto, J. et al. Path (un)predictability of two interacting cracks in polycarbonate sheets using Digital Image Correlation. Sci. Rep. 6, 32278; doi: 10.1038/srep32278 (2016).
References
Cottrell, B. & Rice, J. R. Slightly curved or kinked cracks. Int. J. Fract. 16, 155–169 (1980).
Maiti, S. K. & Smith, R. A. Comparison of the criteria for mixed mode brittle fracture based on the pre-instability stress-strain field, Part I. Int. J. Fract. 23, 281–295 (1983).
Livne, A., Bouchbinder, E. & Fineberg, J. The Breakdown of Linear Elastic Fracture Mechanics near the Tip of a Rapid Crack. Phys. Rev. Lett. 101, 264301 (2008).
Bouchbinder, E., Livne, A. & Fineberg, J. Weakly Nonlinear Theory of Dynamic Fracture. Phys. Rev. Lett. 101, 264302 (2008).
Fender, M. L., Lechenault, F. & Daniels, K. E. Universal Shapes Formed by Two Interacting Cracks. Phys. Rev. Lett. 105, 125505 (2010).
Livne, A., Bouchbinder, E., Svetlizky, I. & Fineberg, J. The Near-Tip Fields of Fast Cracks. Science 327, 1359–1363 (2010).
Cortet, P.-P., Huillard, G., Vanel, L. & Ciliberto, S. Attractive and repulsive cracks in a heterogeneous material. JSTAT 10, 10022 (2008).
Malikova, L. Multi-parameter fracture criteria for the estimation of crack propagation direction applied to a mixed-mode geometry. Eng. Fract. Mech. 143, 32–46 (2015).
Mathieu, F., Hild, F. & Roux, S. Identification of a crack propagation law by digital image correlation. Int. J. Fatig. 36, 146–154 (2012).
Dalbe M. J. et al. Repulsion and Attraction between a Pair of Cracks in a Plastic Sheet. Phys. Rev. Lett. 105, 205501 (2015).
Cortet, P.-P., Vanel, L. & Ciliberto, S. Surface oscillations and slow crack growth controlled by creep dynamics of necking instability. Eur. Phys. J. E. 27, 185–195 (2008).
Seelig, T. H. & Gross, D. On the interaction and branching of fast running cracks - a numerical investigation. J. Mech. Phys. Solids 47, 935–952 (1999).
Melin, S. Why do cracks avoid each other? Int. J. Fract. 23, 37–45 (1983).
Dolbow, J. E. An Extended Finite Element Method with Discontinuous Enrichment for Mechanics, PhD thesis, Northwestern University (1999).
Mroz, K. P. & Mroz, Z. On crack path evolution rules. Eng. Fract. Mech. 77, 1781–1807 (2010).
Boué, T. G., Cohen, G. & Fineberg, J. Origin of the Microbranching Instability in Rapid Cracks. Phys. Rev. Lett. 114, 054301 (2015).
Ghelichi, R. & Kamrin, K. Modeling growth paths of interacting crack pairs in elastic media. Soft Matter 11, 7995 (2015).
Kachanov, M. Elastic solids with many cracks and related problems. Adv. Appl. Mech. 30, 259–445 (1994).
Rethore, J., Gravouil, A., Morestin, F. & Combescure, A. Estimation of mixed-mode stress intensity factors using digital image correlation and an interaction integral. Int. J. Fract. 132, 65–79 (2005).
Pop, O., Meite, M., Dubois, F. & Absi, J. Identification algorithm for fracture parameters by combining DIC and FEM approaches. Int. J. Fract. 170, 101–114 (2011).
Molteno, M. R. & Becker, T. H. Mode I–III Decomposition of the J-integral from DIC Displacement Data. Strain 51, 492–503 (2015).
Rethore, J. Automatic crack tip detection and stress intensity factors estimation of curved cracks from digital images. Int. J. Numer. Meth. Engng. 103, 516–534 (2015).
Mustalahti, M., Rosti, J., Koivisto, J. & Alava, M. J. Relaxation of creep strain in paper. JSTAT 7019 (2010).
Rosti, J., Koivisto, J., Laurson, L. & Alava, M. J. Fluctuations and scaling in creep deformation. Phys. Rev. Lett. 105, 100601 (2010).
Hearn, E. J. Mechanics of Materials 2 (Elsevier, 1997).
Acknowledgements
The authors thank L. Vanel for invaluable discussions. J.K. and M.A. would like to thank Academy of Finland and its Centers of Excellence program for financial support. S.S. acknowledges support from the Aalto University, School of Science via the visiting professor program.
Author information
Authors and Affiliations
Contributions
J.K. and M.-J.D. performed the experiments. J.K. analyzed the data. J.K. and M.J.A. wrote the paper. S.S. and M.J.A. supervised research.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Koivisto, J., Dalbe, MJ., Alava, M. et al. Path (un)predictability of two interacting cracks in polycarbonate sheets using Digital Image Correlation. Sci Rep 6, 32278 (2016). https://doi.org/10.1038/srep32278
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep32278
- Springer Nature Limited
This article is cited by
-
Crack growth and energy dissipation in paper
Scientific Reports (2018)