Abstract
The employment of numerical optimization techniques for parameter tuning of microwave components has nowadays become a commonplace. In pursuit of reliability, it is most often carried out at the level of full-wave electromagnetic (EM) simulation models, incurring considerable computational expenses. In the case of miniaturized microstrip circuits, densely arranged layouts with strong cross-coupling effects make EM-driven tuning imperative to achieve the optimum performance. The process is even more challenging due to a typically large number of geometry parameters, and the lack of reasonable initial designs. The latter often encourages the use of global search procedures, which may be prohibitively expensive. In this paper, a novel automated framework for reliable optimization of miniaturized microwave components is proposed. Our methodology is based on design specification management, where the performance requirements imposed on the system are temporarily relaxed if the current design is unlikely to be improved (e.g., due to being away from the target operating frequency). The specifications are re-adjusted at each iteration of the algorithm, and eventually converge to their original values. Using two examples of compact microstrip couplers and a power divider, the presented technique is demonstrated to significantly improve the efficacy of local search routines under challenging design scenarios.
Similar content being viewed by others
Introduction
Over the recent years, numerical optimization has been playing an increasing role in the design of high-frequency systems, including microwave components and devices1,2,3,4,5,6,7,8. This shift from traditional methods largely based on interactive parameter sweeping, has been motivated by a practical necessity. Tight performance requirements imposed on modern microwave systems, partially dictated by the demands pertinent to emerging application areas, e.g., wireless sensing9, Internet of Things (IoT)10, microwave imaging11, 5G12, autonomous vehicles13, wearable devices14, can only be met if meticulous development of the circuit architecture (e.g., geometry in the case of microstrip components) is supplemented by careful tuning of its parameters. Simultaneous adjustment of multiple variables while accounting for several performance specifications and constraints requires rigorous numerical procedures. To ensure reliability, especially at the final stages of the design process, optimization needs to be conducted at the level of full-wave electromagnetic (EM) simulation models. EM-driven design is of paramount importance especially for systems where simpler performance evaluation methods (e.g., equivalent network models) lack the accuracy. Representative examples include miniaturized microstrip components15,16,17,18, often implemented by folding conventional transmission lines (TLs)19,20, replacing TLs by compact microstrip resonant cells (CMRCs)21,22, or incorporation of the various topological alterations (e.g., defected ground structures23, substrate integrated waveguides24, stubs25, slots26, etc.). All of these result in strong cross-coupling effects, and the increased number of geometry parameters. This adds another layer of complexity to the design closure task, already challenging due to high CPU costs entailed by massive EM evaluations of the system at hand required by conventional optimization procedures.
Improving computational efficiency of simulation-based design procedures has been targeted by numerous research endeavours. These efforts focused on the development of strictly algorithmic approaches, both intrusive (e.g., gradient-based procedures accelerated by means of adjoint sensitivities27,28), and non-intrusive (e.g., trust-region methods with sparse sensitivity updates29,30, as well as surrogate-based frameworks involving data-driven7, and physics-based metamodels5. Although approximation surrogates (kriging31, radial-basis functions32, support vector regression33, polynomial chaos expansion34,35, neural networks36, Gaussian process regression37, polynomial regression38) are by far more popular, their application is limited by the curse of dimensionality, which is particularly troublesome when handling nonlinear outputs of high-frequency structures. Physics-based surrogates exhibit certain tolerance with this respect but require careful selection (and, clearly, availability) of an underlying low-fidelity model. Some popular methods of this category include space mapping39, cognition-driven design40, or various response correction methods41,42. A related class of techniques are those based on variable- and multi-fidelity simulations, e.g., co-kriging43, multi-fidelity procedures44, as well as optimization frameworks involving supervised learning45,46.
Although computational speedup is important, securing robustness of the optimization process may be even more essential when solving practical EM-driven design tasks. This occurs, in particular, when reasonably good initial designs are not available, e.g., in the case of re-designing the structure for a significantly different operating frequencies/bandwidths, or when tuning the parameters of a compact structure involving abbreviated components such as CMRCs21, or folded TLs19. On the one hand, local optimization starting from a poor initial point is likely to fail. On the other hand, engaging global search routines usually turns computationally expensive, often prohibitive. As mentioned before, the various algorithmic solutions outlined in the previous paragraph5,7,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46 are mainly developed to reduce the CPU cost of the EM-driven design procedures with little emphasis on the robustness. Improved reliability can be achieved, to a certain extent, using surrogate-assisted versions of global search routines (mostly population-based metaheuristics47,48). However, applicability of these methods is seriously hindered by the curse of dimensionality, as well as high nonlinearity of microwave circuit characteristics. In practice, only a few independent parameters can be efficiently handled49,50; beyond that, construction of an accurate metamodel covering sufficiently broad ranges of the system variables may become infeasible.
One of the practical issues of microwave design closure is that performance requirements, especially in terms of the target operating frequencies, are often away from those at available initial point (current design), which makes the optimization process fail when using local search techniques. In practice, addressing this problem boils down to altering the specifications and performing repetitive optimization runs while gradually moving the requirements towards the original targets. This approach, while commonly used, is laborious, requires designer interaction and experience-driven specification adjustments. In this paper, a novel technique for enhancing the reliability of local optimization routines through intelligent decision-making has been proposed. Our methodology involves a knowledge-based design specification management scheme, which allows for automated adjustment of the optimization goals based on the detected discrepancies between the actual operating frequencies/bandwidths of the component at hand, and the target ones. Initially, the objectives are shifted into the vicinity of the actual operating conditions of the system, then continuously re-adjusted during the optimization process, and finally converging to their original values. Several benefits of this approach can be identified. First, the optimization algorithm becomes less sensitive to the quality of the initial design. Second, dimension scaling (re-design) of microwave components becomes realizable by means of local methods within broad ranges of operating frequencies. Furthermore, global search procedures are no longer necessary in situations that normally require resorting to such techniques, which indirectly results in reducing the costs of the parameter tuning procedures. Finally, the standard algorithms (e.g., gradient-based routines) can be used in many situations previously fostering utilization of advanced algorithmic frameworks such as surrogate-assisted or sophisticated machine learning methods. The aforementioned advantages have been demonstrated using three microstrip structures, two compact branch-line couplers (a single- and a dual-band), and dual-band power divider, with satisfactory designs rendered through gradient-based optimization with the initial designs being away from the design targets. The presented methodology can be considered a simple yet powerful way of improving the efficacy and reliability of design closure procedures for miniaturized microwave components.
Design specification management for reliable microwave optimization
The purpose of this section is to introduce the design specification adjustment scheme with automated decision-making, as a tool for improving the reliability of microwave design optimization procedures. The specification management concept is a generic one. However, to enable its demonstration, it is combined with a particular local optimization algorithm, here, the trust-region gradient-based search procedure. The remaining part of this section is organized as follows. In “Specification management concept”, we motivate and outline the design specification adjustment concept that is based on the convergence status of the optimization process. Specification adjustment prerequisites” discusses the main assumptions and prerequisites for the adjustment process, whereas the detailed procedure is formulated in “Specification adjustment procedure”. Optimization engine: Trust-region algorithm” briefly recalls the trust-region algorithm, whereas the complete optimization algorithm is summarized in “Optimization algorithm”.
Specification management concept
We aim at alleviating the difficulties of simulation-based parameter tuning of miniaturized microwave components, especially in situations where reasonable initial designs are not readily available. The latter is particularly important when using local optimization algorithms. A representative scenario is re-design (or dimension scaling) of a given structure for operating frequencies that are significantly shifted from those at the currently available design. Under such circumstances, gradient-based and similar routines are likely to fail, whereas resorting to global procedures (typically, population-based metaheuristics51, efficient global optimizers52, or machine learning methods53) entails considerable computational expenses.
In order to explain the automated design specification adjustment concept presented in this work, we start by formulating the EM-driven parameter tuning task. Let us assume that the structure of interest is supposed to operate at the target frequencies fk, k = 1, …, N, where N is the number of operating bands. Given the vector of design variables (typically, geometry parameters) x, the EM-simulated system outputs S(x) (typically, S-parameters versus frequency), and the target operating frequency vector F = [f1 … fN]T, the design task is defined as a minimization problem
where U is an objective function that quantifies the design quality. For example, let us assume that the circuit at hand is a microstrip coupler supposed to operate at the frequency f0. The circuit is to provide equal power split, while minimizing the matching and isolation, both at f0. Thus, the relevant system outputs would be S11, S21, S31, and S41, and the objective function can be defined as
In this example, minimization of matching and isolation is our primary objective, whereas the power split condition is treated as a design constraint, and handled by adding a penalty term with the proportionality coefficient β.
Figure 1 illustrates a common situation where local optimization is prone to a failure due to the poor quality of the initial design. Among the two designs shown in the picture, the operating frequency of the first one (black lines) is sufficiently close to the target, whereas the second design (gray lines) is too far away in terms of the frequency misalignment to make the target attainable when using, e.g., a gradient-based search procedure.
Scattering parameters of an example compact branch-line coupler (consider in “Example 1: Miniaturized branch-line coupler (BLC)”). The target operating frequency is 1.8 GHz, marked using a vertical line. This target is attainable by means of local search when starting from the design represented using the black lines; however, it is not attainable from the design marked using the gray lines. The latter is due to the fact that the operating bandwidth of the circuit is too far away from the target frequency.
The primary goal of this work is to develop algorithmic tools that permit reliable parameter tuning under challenging scenarios such as the one presented in Fig. 1 without defaulting to global optimization methods. Another objective is to avoid excessive computational costs, which would be entailed by straightforward approaches such as multiple optimization runs initiated from random starting points. Here, we propose a design specification adjustment strategy, where the target operating frequencies (or bandwidths) are altered by taking into account the actual operating frequencies of the structure at hand at the currently available design. The prerequisite for such alterations is to ensure that the optimum design with respect to the current status of the specifications is attainable at each stage of the optimization process. Another prerequisite is that the specifications eventually converge to their original levels towards the end of the procedure.
The aforementioned concepts have been illustrated in Fig. 2, and will be rigorously formulated in “Specification adjustment prerequisites” and “Specification adjustment procedure”. At the beginning of the optimization run, the target frequency is shifted to make the temporary goal attainable from a given initial design using a local algorithm. During the optimization process, the specifications are continuously adjusted based on the system outputs at the current design (cf. Fig. 2b,c). At the last stages, when the circuit operates sufficiently close to the original target frequency (or frequencies), the specifications are relocated accordingly so that the optimum design can be identified, again, using the local means. The adjustment of the specifications through automated decision-making process, and the design update (e.g., within the descent type of algorithm) are interleaved so that the entire procedure is concluded within a single algorithm run. It should be noted, that gradual alteration of the design specifications towards the ultimate targets throughout the optimization run is a common practice, when good initial designs are not available. This facilitates identification of the solutions meeting the assumed targets, which would otherwise be unattainable using the local search routines. Nevertheless, such an interactive process is heavily based on engineering insight, it is time consuming, and prone to failure. The approach presented in this work is fully automated, and requires no interaction from the designer. The knowledge necessary to make decisions concerning the scale of the adjustments, and the time of launching them, is acquired from the convergence indicators of the optimization process, design quality (as compared to the current targets), and the initial assessment of the frequency spread of the system outputs.
Automated design specification adjustment concept explained using a branch-line coupler. The initial design and the target operating frequency are the same as in Fig. 1 (initial design marked gray): (a) target frequency relocated towards the operating frequency at the initial design in order to ensure that the current specification (dashed line) are attainable from that design, (b) one of the iterations in the middle of the optimization run with the current design and current specifications, (c) final optimization stage; the target operating frequency converged to its original value, (d) final design optimized with respect to the original design requirement.
Specification adjustment prerequisites
“Specification management concept” discussed the motivation for, the purpose, and potential benefits of involving intelligent decision-making in design specification adjustment. When it comes to its rigorous formulation, one needs to consider the following issues:
-
The necessary amount of specification adjustment has to be quantified based on the available (current) design rendered during the optimization process;
-
The (local) attainability of the adjusted specifications has to be determined when using the current design as the starting point;
-
The above endeavours should be accomplished at low computational cost, preferably without involving extra EM simulations, apart from those already entailed by the operation of the core optimization algorithm itself.
The last factor is dictated by the practical utility of the procedure. Specific arrangements depend on the underlying optimization algorithm, which, in general, would be a type of a gradient-based routine. In this work, we use trust-region gradient search; consequently, the fundamental tool utilized to address the aforementioned issues will be the first-order Taylor expansion of the system frequency characteristics constructed using the sensitivity matrix, which is available at no extra cost: Jacobian has to be updated before each iteration of the trust-region algorithm as a part of its operation.
Let J(x) denote the sensitivity matrix of all relevant system responses at the design x. Without loss of generality, we can assume that the underlying optimization algorithm is an iterative procedure, which yields a series of approximations x(i), i = 0, 1, …, to the optimum design x* of (1); here, x(0) is the initial design. Consider the first-order Taylor model L(i)(x) of S(x) established at the current design x(i). We have
Furhter, let us consider a supplementary optimization problem
In (4), D is the search radius in the vicinity of x(i), typically set to D = 1.
The knowledge-based adjustment of the design specifications will be determined using the following factors:
-
The improvement factor Fr defined as
$$ F_{r} = \left| {U\left( {L^{(i)} \left( {{\mathbf{x}}^{tmp} } \right),{\varvec{F}}} \right) - U\left( {L^{(i)} \left( {{\mathbf{x}}^{(i)} } \right),{\varvec{F}}} \right)} \right| $$(5) -
The distance Dc between the actual operating frequencies of the system at hand at the desing x(i), denoted as Fc = [fc.1 … fc.N]T, and the target frequencies F = [f1 … fN]T, defined as
$$ D_{c} = \left\| {{\varvec{F}}_{c} - {\varvec{F}}} \right\| $$(6)
The first factor, Fr, allows us for assessing the potential for design improvement when starting from the current design x(i). The second factor, Dc, is essentially a safeguard, introduced to ensure that the adjusted specifications are sufficiently close to the actual operating frequencies of the circuit under optimization at the current design. For both factors, the acceptance thresholds are defined: Fr.min and Dc.max (a practical procedure for setting them up will be discussed later). Using these, the design specification will be adjusted if:
-
Fr < Fr.min, i.e., the current design is unlikely to be improved to a sufficient extent, when starting from the current point x(i), or
-
Dc > Dc.max, i.e., the operating frequencies at the design x(i) are too far away from the current targets.
If either of these conditions is satisfied, the current specifications are too strict to be attainable from x(i), and should be relaxed. The acceptance threshold values are not critical; however, it is recommended that the system characteristics are taken into account, especially when deciding about the value of Dc.max. In the following, we provide a simple yet practical procedure for establishing Fr.min and Dc.max:
-
1.
Set Dc.max to approximately half of the system bandwidth(s) at the initial design. This allows to allocate the target frequency (or frequencies) on the slopes of the frequency characteristics near the respective operating bandwidths if Dc < Dc.max;
-
2.
Relocate the target operating frequencies so that Dc = Dc.max (cf. (6));
-
3.
Solve (4) with D = 1;
-
4.
Set Fr.min = Fr, with Fr calculated using the temporary design xtmp obtained in Step 3.
Establishing the threshold Fr.min as described above accounts for a typical improvement of the objective function assuming that design requirements are adjusted to satisfy the condition Dc < Dc.max. As mentioned before, the latter is set to ensure that the operating frequencies of the system can be relocated to the current target frequencies using local search. When using these thresholds for adjusting the target operating frequencies within the actual optimization procedure, the above attainability property is therefore secured at each iteration of the algorithm.
Specification adjustment procedure
We denote by Fcurrent(a) = [fcurrent.1(a) … fcurrent.N(a)]T the updated specifications (target frequencies) for the subsequent, or (i + 1)th, iteration of the optimization procedure. The vector Fcurrent is parameterized by a scalar a, 0 ≤ a ≤ 1. We have
Recall that fc.k are the entries of the vector Fc = [fc.1 … fc.N]T of the actual operating frequencies at the design x(i). The coefficient a is identified as the maximum number a ≤ 1 for which the condition Fr ≥ Fr.min, and Dc ≤ Dc.max, are satisfied at the design xtmp found as (cf. (4))
The meaning of the last statement is that the coefficient a is, as a matter of fact, obtained through an auxiliary optimization procedure, in which it is adjusted (lowered) as much as necessary to eventually ensure that Fr ≥ Fr.min and Dc ≤ Dc.max for the vector xtmp generated by (8). At this point, the specifications have been relaxed to ensure that the target operating frequencies are sufficiently close to those at the design x(i) (in the sense of (6)), and the local improvement of the design (when starting from x(i)) is at least equal to Fr.min. As discussed before, satisfaction of these conditions make the adjusted specs attainable from x(i), and, consequently, throughout the entire optimization process.
Formally speaking, the updated frequency fcurrent.k is a convex combination of fc.k and the original frequency fk. Reducing a leads to relaxing the specifications. When the current design approaches the optimum, the conditions will be satisfied for a = 1, i.e., the value to which the coefficient should eventually converge. The latter will take place if the original specifications are attainable. If this is not the case, the optimization algorithm will be terminated after approaching the target frequencies as closely as possible.
What was described so far in this section pertains to design specification adjustment in one algorithm iteration. The automated adjustment procedure is launched before each iteration, that is, at all points x(i), i = 0, 1, … This results in a continuous modification of the target frequencies based on the current relationships between the system response at x(i) and design targets. At the same time, it should be reiterated that the specification management is not associated with extra computational overhead (here, entailed by additional EM simulations of the system under design): the only required information is the sensitivity matrix, which is available anyhow as its evaluation is a part of the algorithm operation (as mentioned before, gradient-based routines are assumed in this work as the core optimization procedures).
Optimization engine: trust-region algorithm
The design specification management strategy presented in this section can be incorporated into various iterative search procedures. Here, for the sake of demonstration, it is combined with the trust-region (TR) gradient search algorithm54. For the convenience of the reader, it is briefly outlined below. The problem at hand is the minimization task (1), and the algorithm produces a series of approximations x(i), i = 0, 1, …, to x* (cf. (1)), by solving
where L(i) is a linear model (3), Fcurrent represents the current vector of target operating frequencies, whereas trust region radius d(i) is updated after each iteration of the algorithm using the gain ratio r = [U(S(x(i+1)), Fcurrent) − U(S(x(i)), Fcurrent)]/[U(L(i)(x(i+1)), Fcurrent) − U(L(i)(x(i)), Fcurrent)]; r > 0 indicates the design improvement, in which case x(i+1) is accepted. Furthermore, if r is large (e.g., r > 0.75), d(i+1) is updated to 2d(i); if r is too low (e.g., r < 0.25), d(i+1) is reduced to d(i)/3; finally, if r < 0, the new design is rejected, and the iteration is repeated with a reduced TR. The example objective function has been discussed in “Specification management concept” (cf. (2)).
Optimization algorithm
This section provides a description of the complete optimization procedure that combines local optimizer (here, the trust-region algorithm recalled in “Optimization engine: Trust-region algorithm”), and the design specification adjustment procedure of “Specification adjustment procedure”. The algorithm termination is based on the convergence in argument ||x(i+1) − x(i)||< ε, or reduction of the TR radius d(i) < ε. The threshold ε is set to 10−3 in all numerical experiments presented in “Demonstration examples”. It should be noted that in the case of the lack of improvement of the objective function (cf. Step 6), the candidate design is rejected, and the iteration is repeated upon reducing the trust region radius. Interested readers can find more details concerning the trust-region algorithms in in the literature54. The pseudocode of the proposed optimization procedure, as well as the flow diagram have been shown in Figs. 3 and 4, respectively.
Demonstration examples
In this section, the design specification management scheme introduced in “Design specification management for reliable microwave optimization” is demonstrated using three examples of miniaturized microstrip components, including two branch-line couplers (a single- and a dual-band ones), and a dual-band power divider. The numerical experiments are focused on emphasizing the benefits of the specification adjustment, as well as its importance in addressing the challenges related to the lack of quality initial designs.
Example 1: miniaturized branch-line coupler (BLC)
The first verification example is a miniaturized branch-line coupler (BLC)55. The circuit geometry is shown in Fig. 5. The structure is implemented on RO4003 substrate (εr = 3.5, h = 0.76 mm, tanδ = 0.0027). The design variables are x = [g l1r la lb w1 w2r w3r w4r wa wb]T. Other parameters are described by the following relations: L = 2dL + Ls, Ls = 4w1 + 4g + s + la + lb, W = 2dL + Ws, Ws = 4w1 + 4g + s + 2wa, l1 = lbl1r, w2 = waw2r, w3 = w3rwa, and w4 = w4rwa. The computational model of the structure is implemented in CST Microwave Studio and simulated using the frequency domain solver (~ 60,000 mesh cells, simulation time about 5 min).
Miniaturized branch-line coupler (BLC)55. The circuit ports marked using numbered circles.
The design problem is stated as follows. The circuit is to operate at the frequency f0 = 1 GHz, at which the matching |S11|, and isolation |S41| are to be simultaneously minimized. Also, the circuit has to ensure equal power split, i.e., |S21| =|S31| at f0. The objective function is formulated as in (2). Figure 6 shows the initial design selected for this problem (gray lines), as well as the final design obtained using the proposed approach (black lines). It can be observed that the operating frequency of the BLC at the initial design is at about 2.2 GHz, which makes it essentially impossible to re-design the structure to 1 GHz using local means. As a matter of fact, the conventional trust-region routine fails to do so. On the other hand, the proposed approach works well, and produces the design x* = [1.00 0.81 6.91 11.94 0.75 0.99 0.89 0.65 4.05 0.53]T, also illustrated in Fig. 6. The evolution of the target operating frequency has been shown in Fig. 7. Initially, the specifications have to be severely adjusted in order to ensure a success of local search, then gradually converge to 1 GHz after about ten iterations of the optimization process. Some of the intermediate designs produced in the course of the optimization run have been illustrated in Fig. 8.
Branch-line coupler: scattering parameters at three intermediate designs, marked using the light-gray, dark-gray, and black colors (optimum), along with the corresponding target frequencies. For the sake of clarity, the matching/isolation characteristics are shown separate from the transmission characteristics.
Example 2: dual-band branch-line coupler
The second example is a dual-band branch line coupler56 shown in Fig. 9, implemented on the RO4003 substrate (εr = 3.5, h = 0.51 mm, tanδ = 0.0027). There circuit geometry is described by nine independent parameters x = [Ls Ws l3r w1 w2 w3 w4 w5 wv]T (all dimensions in mm, except l3r, which is a relative parameter). Furthermore, we have the following relationships: dL = dW = 10 mm, L = 2dL + Ls, W = 2dW + 2w1 + (Ws − 2wf), l1 = Ws/2, l2 = l321/2, l3 = l3r((Ls − w3)/2 − w4/21/2), lv1 = l3/3, and lv3 = Ls/2 − w3/2 − l3 + lv1; wf = 1.15 mm is fixed to ensure 50-Ω line impedance. The computational model is implemented in CST Microwave Studio and evaluated using its time domain solver (~ 150,000 mesh cells, simulation time about 2 min).
Dual-band branch-line coupler56; circuit topology; port marked with numbers in circles.
For this example, the design objective is to optimize the geometry parameters so that the circuit operates at the frequencies f1 = 1.2 GHz and f2 = 2.7 GHz, with the input matching |S11|, and isolation |S41| simultaneously minimized at both f1 and f2. Furthermore, the circuit has to ensure equal power split, i.e., |S21| =|S31| at f1 and f2. The objective function for this problem is based on (2).
The initial design is shown in Fig. 10 using the gray lines. The operating frequencies at x(0) (around 1.7 GHz and 3.5 GHz, respectively) are severely misaligned with the target ones, and conventional local optimization fails to yield satisfactory results. The proposed approach renders the design x* = [41.1 8.19 0.95 2.26 1.68 0.96 0.34 1.18 1.14]T (responses marked black in Fig. 10) that is of high quality with respect to the assumed goals. The evolution of the target operating frequency has been shown in Fig. 11. Similarly as in the first test case, the specifications are considerably relocated and eventually converge to the original values after ten iterations of the algorithm. Figure 12 shows the selected intermediate designs along with the respective target operating frequencies.
Dual-band branch-line coupler: scattering parameters at the three intermediate designs, marked using the light-gray, dark-gray, and black colors (optimum), along with the corresponding target frequencies. For the sake of clarity, the matching/isolation characteristics are shown separate from the transmission characteristics.
Example 3: dual-band power divider
Our last example is a dual-band equal split power divider based on coupled lines57, shown in Fig. 13. The circuit is implemented on AD250 dielectric substrate (εr = 2.5, h = 0.81 mm, tanδ = 0.0018). There are seven adjustable parameters x = [l1 l2 l3 l4 l5 s w2]T (all dimensions in mm); w1 = 2.2 is fixed to ensure 50-Ω line impedance; g = 1 mm is also fixed. The computational model is implemented in CST Microwave Studio and evaluated using its time domain solver (~ 200,000 mesh cells, simulation time approx. 2 min).
Dual-band equal split power divider57; circuit topology; port marked with numbers in circles. Lumped resistor denoted as R.
The design objective is to optimize the geometry parameters so that the circuit operates at the frequencies f1 = 2.4 GHz and f2 = 3.8 GHz, with the input matching |S11|, output matching |S22|, |S33|, as well as isolation |S23| simultaneously minimized at both f1 and f2. The equal power split condition is not directly handled in the optimization process because it is implied by the structure symmetry. The initial design is shown in Fig. 14 using the gray lines). The operating frequencies at x(0) (around 1.4 GHz and 2.0 GHz, respectively) are away from the target ones. Similarly as for the two previous examples, conventional local optimization fails to produce satisfactory results. The methodology proposed in this work yields the design x* = [26.86 2.18 21.92 2.00 3.82 0.50 4.56]T (marked black in Fig. 14), which meets the performance requirements imposed on the structure.
The evolution of the target operating frequencies has been shown in Fig. 15. It is consistent with what was observed in previous sections: following the initial (and significant) adjustment, the target frequencies converge to their original values towards the end of the optimization process. Figure 16 shows the selected intermediate designs along with the respective target operating frequencies.
Dual-band power divider: scattering parameters at the three intermediate designs, marked using the light-gray, dark-gray, and black colors (optimum), along with the corresponding target frequencies. For clarity, the input matching and transmission responses, as well as the output matching and isolation responses are shown in separate panels.
Conclusion
In this work, a novel design specification adjustment procedure through intelligent decision-making has been introduced to improve the reliability of EM-driven optimization of miniaturized microwave components. The procedure is intended to be used with local iterative search procedures (primarily gradient-based routines of a descent type), and to alleviate the difficulties related to the lack of reasonable initial designs. The proposed approach allows for automated and adaptive modification of the design objectives in terms of the target operating frequencies or bandwidths, so that the relocated targets are attainable at any given stage of the optimization process from the currently available design. Essentially, it is a knowledge-based methodology that employs several indicators related to the convergence status of the optimization process, frequency spread of the system characteristics, and quantified misalignment between the actual and required operating conditions. Rigorous criteria have been defined and implemented to activate the design specification adjustment, and to decide about the amount thereof. Our technique—upon coupling with the trust-region gradient-based algorithm—has been comprehensively validated using three microstrip circuits, a single-band and a dual-band branch-line couplers, and a dual-band power divider. In all considered cases, the optimization process was demonstrably convergent to satisfactory designs despite of poor starting points, at which the operating frequencies of the respective structures have been severely misaligned with the target ones. Based on these results, it can be concluded that the presented methodology significantly improves reliability of the optimization procedure.
The principal advantage of the proposed intelligent design specification management is a reduction of the optimization process sensitivity to the quality of the initial design. Some of the practically important consequences include a possibility of re-designing (dimension scaling) of microwave components within broad ranges of operating conditions using local procedures, as well as limiting the need for global search algorithms (or various advanced approaches such as surrogate-assisted or machine learning frameworks) when handling more challenging parameter tuning tasks. Furthermore, the presented technique allows for replacing heuristic and interactive (experience-driven) methods of design specifications adjustment, effectively leading to a considerable shortening of design closure cycles under challenging scenarios.
References
Feng, F. et al. Adaptive feature zero assisted surrogate-based EM optimization for microwave filter design. IEEE Microw. Wirel. Compon. Lett. 29, 2–4 (2019).
Bao, C., Wang, X., Ma, Z., Chen, C.-P. & Lu, G. An optimization algorithm in ultrawideband bandpass Wilkinson power divider for controllable equal-ripple level. IEEE Microw. Wirel. Compon. Lett. 30, 861–864 (2020).
Sharma, S. & Sarris, C. D. A novel multiphysics optimization-driven methodology for the design of microwave ablation antennas. IEEE J. Multiscale Multiphys. Comput. Tech. 1, 151–160 (2016).
Zhao, P. & Wu, K. Homotopy optimization of microwave and millimeter-wave filters based on neural network model. IEEE Trans. Microw. Theory Tech. 68, 1390–1400 (2020).
Van Nechel, E., Ferranti, F., Rolain, Y. & Lataire, J. Model-driven design of microwave filters based on scalable circuit models. IEEE Trans. Microw. Theory Tech. 66, 4390–4396 (2018).
Guo, L. & Abbosh, A. M. Optimization-based confocal microwave imaging in medical applications. IEEE Trans. Antennas Propag. 63, 3531–3539 (2015).
Zhang, Z., Cheng, Q. S., Chen, H. & Jiang, F. An efficient hybrid sampling method for neural network-based microwave component modeling and optimization. IEEE Microw. Wirel. Compon. Lett. 30, 625–628 (2020).
Bianchi, C., Bressan, F., Dughiero, F. & Hunter, R. Novel efficient strategy to design an optimized microwave shield. IEEE Trans. Magn. 52, 1–4 (2016).
Abdolrazzaghi, M. & Daneshmand, M. A phase-noise reduced microwave oscillator sensor with enhanced limit of detection using active filter. IEEE Microw. Wirel. Compon. Lett. 28, 837–839 (2018).
Wang, Y., Zhang, J., Peng, F. & Wu, S. A glasses frame antenna for the applications in internet of things. IEEE Internet Things J. 6, 8911–8918 (2019).
Yurduseven, O., Gowda, V. R., Gollub, J. N. & Smith, D. R. Printed aperiodic cavity for computational and microwave imaging. IEEE Microw. Wirel. Compon. Lett. 26, 367–369 (2016).
Ali, M. M. M. & Sebak, A. Compact printed ridge gap waveguide crossover for future 5G wireless communication system. IEEE Microw. Wirel. Compon. Lett. 28, 549–551 (2018).
Kim, M. & Kim, S. Design and fabrication of 77-GHz radar absorbing materials using frequency-selective surfaces for autonomous vehicles application. IEEE Microw. Wirel. Compon. Lett. 29, 779–782 (2019).
Lee, C., Bai, B., Song, Q., Wang, Z. & Li, G. Microwave resonator for eye tracking. IEEE Trans. Microw. Theory Tech. 67, 5417–5428 (2019).
Gómez-García, R., Yang, L., Muñoz-Ferreras, J. & Psychogiou, D. Single/multi-band coupled-multi-line filtering section and its application to RF diplexers, bandpass/bandstop filters, and filtering couplers. IEEE Trans. Microw. Theory Tech. 67, 3959–3972 (2019).
Tan, X., Sun, J. & Lin, F. A compact frequency-reconfigurable rat-race coupler. IEEE Microw. Wirel. Compon. Lett. 30, 665–668 (2020).
Ahn, H. & Tentzeris, M. M. Ultra-compact and wideband V(U)HF 3-dB power dividers consisting of novel asymmetric impedance transformers. IEEE Access. 7, 76367–76375 (2019).
Yang, Y., Hu, N., Xie, W., Wang, W. & Wu, Y. A compact tri-band impedance-transforming power divider with independent controllable power division ratios and enhanced bandwidths. IEEE Access. 7, 25185–25194 (2019).
Martinez, L., Belenguer, A., Boria, V. E. & Borja, A. L. Compact folded bandpass filter in empty substrate integrated coaxial line at S-Band. IEEE Microw. Wirel. Compon. Lett. 29, 315–317 (2019).
Hou, Z. J. et al. A compact and low-loss bandpass filter using self-coupled folded-line resonator with capacitive feeding technique. IEEE Electron Device Lett. 39, 1584–1587 (2018).
Chen, S. et al. A frequency synthesizer based microwave permittivity sensor using CMRC structure. IEEE Access 6, 8556–8563 (2018).
Qin, W. & Xue, Q. Elliptic response bandpass filter based on complementary CMRC. Electron. Lett. 49, 945–947 (2013).
Sen, S. & Moyra, T. Compact microstrip low-pass filtering power divider with wide harmonic suppression. IET Microw. Antennas Propag. 13, 2026–2031 (2019).
Liu, S. & Xu, F. Compact multilayer half mode substrate integrated waveguide 3-dB coupler. IEEE Microw. Wirel. Compon. Lett. 28, 564–566 (2018).
Wei, F., Jay Guo, Y., Qin, P. & Wei Shi, X. Compact balanced dual- and tri-band bandpass filters based on stub loaded resonators. IEEE Microw. Wirel. Compon. Lett. 25, 76–78 (2015).
Zhang, W., Shen, Z., Xu, K. & Shi, J. A compact wideband phase shifter using slotted substrate integrated waveguide. IEEE Microw. Wirel. Compon. Lett. 29, 767–770 (2019).
Sabbagh, M. A. E., Bakr, M. H. & Bandler, J. W. Adjoint higher order sensitivities for fast full-wave optimization of microwave filters. IEEE Trans. Microw. Theory Tech. 54, 3339–3351 (2006).
Koziel, S., Mosler, F., Reitzinger, S. & Thoma, P. Robust microwave design optimization using adjoint sensitivity and trust regions. Int. J. RF Microw. CAE 22, 10–19 (2012).
Pietrenko-Dabrowska, A. & Koziel, S. Expedited antenna optimization with numerical derivatives and gradient change tracking. Eng. Comput. 37, 1179–1193 (2019).
Pietrenko-Dabrowska, A. & Koziel, S. Computationally-efficient design optimization of antennas by accelerated gradient search with sensitivity and design change monitoring. IET Microw. Antennas Propag. 14, 165–170 (2020).
Li, Y., Xiao, S., Rotaru, M. & Sykulski, J. K. A dual kriging approach with improved points selection algorithm for memory efficient surrogate optimization in electromagnetics. IEEE Trans. Magn. 52, 1–4 (2016).
Barmuta, P., Ferranti, F., Gibiino, G. P., Lewandowski, A. & Schreurs, D. M. M. P. Compact behavioral models of nonlinear active devices using response surface methodology. IEEE Trans. Microw. Theory Tech. 63, 56–64 (2015).
Cai, J., King, J., Yu, C., Liu, J. & Sun, L. Support vector regression-based behavioral modeling technique for RF power transistors. IEEE Microw. Wirel. Compon. Lett. 28, 428–430 (2018).
Spina, D., Ferranti, F., Antonini, G., Dhaene, T. & Knockaert, L. Efficient variability analysis of electromagnetic systems via polynomial chaos and model order reduction. IEEE Trans. Compon. Packag. Manuf. Technol. 4, 1038–1051 (2014).
Petrocchi, A. et al. Measurement uncertainty propagation in transistor model parameters via polynomial chaos expansion. IEEE Microw. Wirel. Compon. Lett. 27, 572–574 (2017).
Feng, F. et al. Multifeature-assisted neuro-transfer function surrogate-based EM optimization exploiting trust-region algorithms for microwave filter design. IEEE Trans. Microw. Theory Tech. 68, 531–542 (2020).
Jacobs, J. P. Characterization by Gaussian processes of finite substrate size effects on gain patterns of microstrip antennas. IET Microwa. Antennas Propag. 10, 1189–1195 (2016).
Kamel Ariffin, M. F., Idris, A. & Ngadiman, N. H. A. Optimization of one-pot microwave-assisted ferrofluid nanoparticles synthesis using response surface methodology. IEEE Trans. Magn. 54, 1–6 (2018).
Li, S., Fan, X., Laforge, P. D. & Cheng, Q. S. Surrogate model-based space mapping in postfabrication bandpass filters’ tuning. IEEE Trans. Microw. Theory Tech. 68, 2172–2182 (2020).
Zhang, C., Feng, F., Gongal-Reddy, V., Zhang, Q. J. & Bandler, J. W. Cognition-driven formulation of space mapping for equal-ripple optimization of microwave filters. IEEE Trans. Microw. Theory Tech. 63, 2154–2165 (2015).
Koziel, S. Shape-preserving response prediction for microwave design optimization. IEEE Trans. Microw. Theory Tech. 58(11), 2829–2837 (2010).
Koziel, S. & Unnsteinsson, S. D. Expedited design closure of antennas by means of trust-region-based adaptive response scaling. IEEE Antennas Wirel. Propag. Lett. 17, 1099–1103 (2018).
Pietrenko-Dabrowska, A. & Koziel, S. Surrogate modeling of impedance matching transformers by means of variable-fidelity EM simulations and nested co-kriging. Int. J. RF Microw. CAE 30, e22268 (2020).
Feng, F. et al. Coarse- and fine-mesh space mapping for EM optimization incorporating mesh deformation. IEEE Microw. Wirel. Compon. Lett. 29, 510–512 (2019).
Liu, B., Yang, H. & Lancaster, M. J. Global optimization of microwave filters based on a surrogate model-assisted evolutionary algorithm. IEEE Trans. Microw. Theory Tech. 65, 1976–1985 (2017).
Xiao, L. et al. Parametric modeling of microwave components based on semi-supervised learning. IEEE Access 7, 35890–35897 (2019).
Toktas, A., Ustun, D. & Tekbas, M. Multi-objective design of multi-layer radar absorber using surrogate-based optimization. IEEE Trans. Microw. Theory Tech. 67, 3318–3329 (2019).
Torun, H. M. & Swaminathan, M. High-dimensional global optimization method for high-frequency electronic design. IEEE Trans. Microw. Theory Tech. 67, 2128–2142 (2019).
Lim, D., Yi, K., Jung, S., Jung, H. & Ro, J. Optimal design of an interior permanent magnet synchronous motor by using a new surrogate-assisted multi-objective optimization. IEEE Trans. Magn. 51, 8207504 (2015).
Taran, N., Ionel, D. M. & Dorrell, D. G. Two-level surrogate-assisted differential evolution multi-objective optimization of electric machines using 3-D FEA. IEEE Trans. Magn. 54, 8107605 (2018).
Luo, X., Yang, B. & Qian, H. J. Adaptive synthesis for resonator-coupled filters based on particle swarm optimization. IEEE Trans. Microw. Theory Tech. 67, 712–725 (2019).
Liu, B., Akinsolu, M. O., Ali, N. & Abd-Alhameed, R. Efficient global optimisation of microwave antennas based on a parallel surrogate model-assisted evolutionary algorithm. IET Microw. Antennas Propag. 13, 149–155 (2019).
Xiao, L., Shao, W., Ding, X. & Wang, B. Dynamic adjustment kernel extreme learning machine for microwave component design. IEEE Trans. Microw. Theory Tech. 66, 4452–4461 (2018).
Conn, A. R., Gould, N. I. M. & Toint, P. L. Trust region methods (SIAM, 2000).
Tseng, C. & Chang, C. A rigorous design methodology for compact planar branch-line and rat-race couplers with asymmetrical T-structures. IEEE Trans. Microw. Theory Tech. 60, 2085–2092 (2012).
Xia, J., Li, B., Twumasi, A., Liu, P. & Gao, S. Planar dual-band branch-line coupler with large frequency ratio. IEEE Access 8, 33188–33195 (2020).
Lin, Z. & Chu, Q.-X. „A novel approach to the design of dual-band power divider with variable power dividing ratio based on coupled-lines. Prog. Electromagn. Res. 103, 271–284 (2010).
Acknowledgements
The authors would like to thank Dassault Systemes, France, for making CST Microwave Studio available. This work is partially supported by the Icelandic Centre for Research (RANNIS) Grant 217771 and National Science Centre of Poland Grant 2020/37/B/ST7/01448.
Author information
Authors and Affiliations
Contributions
Conceptualization, S.K. and A.P.; methodology, S.K. and A.P.; software, S.K. and A.P.; validation, S.K. and A.P.; formal analysis, S.K.; investigation, S.K. and A.P.; resources, S.K. and P.P.; data curation, S.K. and A.P.; writing—original draft preparation, S.K. and A.P.; writing—review and editing, S.K.; visualization, S.K. and A.P.; supervision, S.K.; project administration, S.K. and P.P.; funding acquisition, S.K. and P.P. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Koziel, S., Pietrenko-Dabrowska, A. & Plotka, P. Design specification management with automated decision-making for reliable optimization of miniaturized microwave components. Sci Rep 12, 829 (2022). https://doi.org/10.1038/s41598-022-04810-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-04810-1
- Springer Nature Limited
This article is cited by
-
Improved efficacy behavioral modeling of microwave circuits through dimensionality reduction and fast global sensitivity analysis
Scientific Reports (2024)
-
Rapid and reliable re-design of miniaturized microwave passives by means of concurrent parameter scaling and intermittent local tuning
Scientific Reports (2023)
-
Knowledge-based expedited parameter tuning of microwave passives by means of design requirement management and variable-resolution EM simulations
Scientific Reports (2023)
-
3D metamaterial ultra-wideband absorber for curved surface
Scientific Reports (2023)
-
Narrow-band power dividers with wide range tunable power-dividing ratio
Scientific Reports (2022)