Abstract
Recent progresses on nanocapillary-driven water transport under metastable conditions have substantiated the potential of artificial trees for dewatering applications in a wide pressure range. This paper presents a comprehensive performance analysis of artificial trees encompassing the principle for negative capillary pressure generation; impacts of structural, compositional, and environmental conditions on dewatering performance; and design considerations. It begins by delineating functionalities of artificial trees for evaporation (leaves), conduction (xylem), and filtration (root) of water, in the analogy to natural trees. The analysis revealed that the magnitude of (negative) capillary pressure in the artificial leaves and xylem must be sufficiently large to overcome the osmotic pressure of feed at the root. The required magnitude can be reduced by increasing the osmotic pressure in the artificial xylem conduits, which reduces the risk of cavitation and subsequent blockage of water transport. However, a severe concentration polarization that can occur in long xylem conduits would negate such compensation effect of xylem osmotic pressure, leading to vapor pressure depression at the artificial leaves and therefore reduced dewatering rates. Enhanced Taylor dispersions by increasing xylem conduit diameters are found to alleviate the concentration polarization, allowing for water flux enhancement directly by increasing leaf-to-root membrane area ratio.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
As one of the core processes for liquid–solid separation, dewatering is implemented in an ample range of industrial sector, including construction1,2, food processing3,4, metal recovery5, biofuel production6,7, and wastewater treatment8,9. In light of the increasing practice of zero-liquid discharge, dewatering is also becoming a critical process for addressing environmental concerns arising from industrial wastewater disposal. For instance, the tailing ponds in Alberta, Canada, which contain more than 1.2 trillion litre of the oil–sand produced water, containing toxic chemicals and encompassing over 220 km2, are an immense liability to Canadian industries10,11. For residential and commercial sectors, effective water removal is integral to stormwater management, as urban flooding may incur sewage overflow, pollutant spread, and outbreak of waterborne diseases12,13. While the primary emphasis of dewatering is on the production of concentrated solids or removal of excessive unwanted water, in a broader aspect reusable water can also be produced by dewatering processes when the removed water is captured14.
Trees are an effective natural dewatering instrument; up to 97% of absorbed water at roots is transpired to the atmosphere15, contributing almost 40% of the annual precipitation over the land16. Trees generate a negative capillary pressure in their leaf cells, transduce it through xylem to root cells for water uptake at the root, and conduct water to the leaves, from which water evaporates (i.e., transpiration)17,18. The cohesion-tension theory is well-accepted to explain the generating mechanism of negative capillary pressures17,18,19. An air–liquid water interface (meniscus) is formed in channels within the cell walls of leaf mesophyll cells, equivalent to nanopores with diameters of O(10 nm)19,20. With the meniscus pinned at the periphery of the nanopore, the removed water molecules by transpiration are immediately displaced by water molecules underneath and the chain of water molecules moves upward. Accordingly, a tension force, equivalent to negative pressure, arises in the water molecular chain. The surface tension of water in a nanopore with the diameter of 20 nm can generate a capillary pressure of < − 100 bar, which serves as the driving force for water transport even in giant sequoia (> 100 m in height)21.
As salt-tolerant trees, mangroves further extend the use of the negative capillary pressure to the tight control of water and ion uptake, rendering their xylem to be nearly salt-free22,23. The blockage of their non-selective route for water and salt passage (apoplastic route) effectively diverts the flow to the selective route (symplastic route); cell lipid membranes and salt-excluding water channels called aquaporins enable a selective water permeation through the root cells. The sufficiently negative capillary pressure generated in mangrove trees overcomes the osmotic pressure in the soil (e.g., ~ 25 bar for seawater), allowing for water uptake in their saline habitat.
This nanocapillary-driven mechanism in trees has been explored for engineering purposes, including energy harvesting24,25 and chemical sensing26,27. The major challenge lies in that liquid water under negative pressure is at a metastable condition, prone to bubble formation and cavitation (called embolism), which potentially blocks the water passage28,29. The susceptibility to embolism has limited experimental demonstrations in artificial platforms to a rather low-pressure range (< ~ 25 bar, seawater osmotic pressure)24,25,26,27,30. In light of this challenge, Stroock and colleagues demonstrated water transport in microfluidic platforms, driven by negative capillary pressures equivalently down to ~ − 1000 bar31,32. In a recent study by the present author and colleagues33, an artificial mangrove was presented for hypersaline brine desalination through generating a negative pressure approaching − 300 bar in nanocapillaries and hydrogel, used as artificial leaves. The highly hydrophilic porous silica employed as stem greatly enhanced the stability of water transport under negative pressure, and enabled almost 50 h-long desalination of 5 M NaCl brine, far exceeding the treatable salinity limit (~ 1.3 M NaCl) of conventional reverse osmosis (RO) processes34. These recent progresses support the feasibility of the tree-mimicking dewatering in a wide pressure range. Futuristic applications of this dewatering mechanism by constructing artificial trees have also been proposed for large-scale solar desalination35 as well as urban stormwater management and surface cooling33.
The water flow in nanocapillary-driven artificial trees is a coupled outcome of multiple mass transfer phenomena and multi-phase thermodynamics, including water permeation and solute rejection via steric hindrance or solution-diffusion mechanism (root), convective and diffusive flows (stem and external environment), and liquid–vapor phase equilibrium (leaf). To author’s knowledge, previous studies are primarily focused on local transfer phenomena, which calls for a systematic analysis that accounts for interconnected, multiple transfer phenomena and provides guidelines in designing artificial trees for engineering systems. This paper conducts a systematic modelling on the water transport in an artificial tree of any arbitrary scale through coupling the transfer phenomena in dense/porous media and two-phase thermodynamics, and aims to present the potential of the tree-mimicking, passive and fast dewatering process for large-scale engineering and environmental applications. The paper begins with delineating the functional similarities of water transport between a natural (mangrove) tree and the artificial tree, followed by analyzing the impacts of structural, compositional, and environmental conditions on the dewatering performance. Finally, perspectives and key design considerations are discussed.
Modelling water transport in artificial trees
A dewatering process by natural (mangrove) trees may be simplified into three steps: water filtration by root, conduction through the stem, and transpiration at the leaves (Fig. 1A). As an illustrative example of nanocapillary-driven large-scale dewatering processes33,35, we take an artificial tree hypothetically constructed on a building, potentially for urban stormwater management, consisting of the solute rejecting membrane at the foundation, hydrophilic porous conduit, and a nanoporous layer at the roof and the wall surface. Analyses for other environmental applications such as dewatering of high salinity brine or tailing ponds can readily be derived from this illustration. A porous material in the building wall (xylem in the stem) conducts water to the evaporative surfaces that comprise nanopores on the building walls and roofs (leaves). For simplicity, several assumptions are made: (1) xylem conduits are bundles of cylindrical tubes with a uniform diameter; (2) the total cross-section area of xylem conduits is equated to the root membrane area; (3) water transport through all the artificial tree components is assumed to occur under isothermal condition; (4) any solutes in the artificial tree and in the water on the ground (feed) are modelled as NaCl due to its prevalence in natural environments and well-documented osmotic pressure data; and (5) a complete solute rejection at the root membrane is assumed.
Overview of dewatering process by an artificial tree. (A) Schematic illustrations of a natural mangrove tree and an artificial tree for dewatering process, and their similarities in functions: filtration (root), conduction (stem), and evaporation (leaf) of water. (B) Distributions of chemical potential of water, pressure, and solute concentration through the artificial tree at different locations.
Macroscopically, the gradient of chemical potential (\(\mu\)) through the artificial tree is the driving force for water transport from the feed to the ambient (Fig. 1B). Microscopically, a capillary pressure generated in the leaf pores exerts a mechanical force to drive the water through the root membrane and xylem conduits in the stem. The pressure discontinuity across the liquid–vapor interface (meniscus), formed inside the leaf pore, results in a negative, capillary pressure described by the Young–Laplace equation19,33:
where PH and Pa are the hydraulic pressure in the leaf pore (at \(z = H\)) and the ambient pressure, respectively; \(\gamma\) and \(\theta\) are the surface tension of water and the contact angle between the meniscus and the pore wall surface, respectively. The contact angle (\(\theta\)) serves as ‘knob’ of the magnitude of \(P_{H}\), and the largest pressure discontinuity occurs when \(\theta\) becomes the receding contact angle (\(\theta_{min}\))19,33. For highly hydrophilic pore materials, \(\theta_{min} = 10^\circ\) is assumed.
For mild evaporative fluxes from leaf pores, a near-equilibrium of liquid and vapor phases is satisfied. Taking water vapor as an ideal gas, the chemical potentials of water in vapor (\(\mu_{H}^{\left( v \right)}\)) and liquid (\(\mu_{H}^{\left( l \right)}\)) phases are expressed as follows36,37,38 (Supplementary note S1):
Here R, T, and g are the universal gas constant, temperature, and gravitational acceleration, respectively; \(\rho_{w}\) and \(\overline{v}_{w}\) are the density and the molar volume of liquid water; \(\mu^{0} \left( T \right)\) is the chemical potential of water at the reference state (i.e., pure water with a flat liquid–vapor interface and under its saturation vapor pressure, \(P_{sat}^{0} (T)\)). The second term in the right-hand-side of Eq. (3) stands for the contribution to the chemical potential by the osmotic pressure (\({\Pi }_{H}\)) of the liquid phase in the xylem, the third term by hydraulic pressure (PH), and the last term by gravity.
The evaporative mass flux of water vapor from the leaf pores, Jw(v), is expressed as follows:
where PH(v) and P∞(v) are the saturation vapor pressure at the meniscus (\(z = H\)) and the partial pressure of vapor in the far ambient (\(z = z_{\infty }\)), respectively; \(k_{leaf}\) is the mass transfer coefficient. For a given root membrane area (Aroot), the mass flux of liquid water through the root membrane (Jw) can be amplified by increasing the leaf-to-root area ratio (\(A_{R} \equiv A_{leaf} /A_{root} )\): \(J_{w} = A_{R} J_{w}^{\left( v \right)}\).
Requiring \(\mu_{H}^{\left( v \right)} = \mu_{H}^{\left( l \right)}\) and combining with Eq. (4), we can connect the hydraulic pressure in the leaf pore (PH), which is negative in value, with external conditions of the environment (\(P_{\infty }^{\left( v \right)}\), T, and kleaf), the structural conditions (H and AR), and the solution composition in the xylem (\({\Pi }_{H}\)):
The hydraulic pressure at the interface of the root membrane and the stem, \(P_{0}\), can then be obtained through the momentum balance:
where \(\eta\) is the dynamic viscosity of liquid water and dX is the diameter of xylem conduit. The first and the second terms in the parenthesis stand for pressure drop by viscous loss and hydrostatic pressure, respectively.
The water flux across the salt-rejecting root membrane, such as RO membrane, can be estimated using the solution-diffusion model39:
Here Am is the water permeability; \(\Delta P = P_{a} - P_{0}\) and \(\Delta {\Pi } = {\Pi }_{ - \delta } - {\Pi }_{0}\); \({\Pi }_{ - \delta }\) and \({\Pi }_{0}\) are the osmotic pressure at the feed-root membrane interface and the xylem-root membrane interface, respectively. It is apparent that Jw becomes positive (i.e., dewatering) only when \(\Delta P > \Delta {\Pi }\). When Jw > 0, the solute concentration (\({\text{C}}_{F, - \delta }\)) and the osmotic pressure (\({\Pi }_{ - \delta }\)) at the feed-root membrane interface is increased from those in the bulk feed (\({\text{C}}_{F, - \infty }\) and \({\Pi }_{ - \infty }\)) due to the concentration polarization in the feed (Supplementary note S1).
When solutes are present in the xylem conduit, the solute concentrations at the xylem interface with the root membrane (CX,0) and with the leaf pore (CX,H) can be determined by the balance between the convective and diffusive salt fluxes inside the xylem conduit (Supplementary note S1 and S3):
where \(\overline{C}_{X}\) is a volume-averaged concentration in the xylem; Deff stands for an effective diffusion coefficient that accounts for both molecular diffusion and Taylor dispersion. The osmotic pressures in the xylem, \({\Pi }_{0}\) (at \(z = 0\)) and \({\Pi }_{H}\) (at \(z = H\)), were calculated using a commercial software (OLI Systems, Morris Plains, NJ) as the function of the solute (NaCl) concentrations \(C_{X,0}\) and \(C_{X,H}\). These coupled Eqs. (2)–(9) are solved simultaneously to find Jw by the Newton–Raphson iterative method40 (Supplementary note S1). The nomenclature of all variables used is summarized in Supplementary note Table S1.
Water evaporation from leaves
Dependency of water evaporation rate on external conditions of the environment
At the artificial leaves, the higher partial pressure of vapor at the meniscus in the leaf pore (at \(z = H\)) than that in the far ambient (at \(z = z_{\infty }\)), which is determined by the relative humidity (RH) of the ambient, drives the transport of water molecules across a boundary layer of water vapor concentration. Under the turbulent flow condition, the following Sherwood correlation may be used to obtain \(k_{leaf}\)41:
Here \(Sh_{leaf} \equiv k_{leaf} \left( {\frac{RT}{{\varepsilon M_{w} }}} \right)\frac{L}{{D_{w}^{\left( v \right)} }}\)33; Mw is the molar mass of water; L is the characteristic length over which the boundary layer of water vapor concentration develops and \(D_{w}^{\left( v \right)}\) is the diffusion coefficient of water vapor; \(Sc = \nu_{a} /D_{w}^{\left( v \right)}\) and \(Re_{L} = U_{\infty } L/\nu_{a}\), where \(\nu_{a}\) is the kinematic viscosity of air. Hereafter, leaf surface porosity (ε) of 0.4, air velocity (\(U_{\infty }\)) of 1.4 m s−1 (= 5 km h−1), and feed flow velocity (\(U_{ - \infty }\)) of 1 m s−1 are set for calculation. L = 50 m is assumed as a commonly observable length scale of urban buildings.
The evaporative water flux (Jw(v)) is calculated from Eq. (4), with RH expressed as: \(RH = P_{\infty }^{\left( v \right)} /P_{sat}^{0} \left( T \right)\). Figure 2A shows the dependency of Jw(v) on the temperature and RH in the ambient. The same model (Eq. 4) applied for the lab-scale artificial tree reported by our previous study shows strong agreement with the experimental measurements (Fig. 2A inset)33. Given a mass transfer coefficient (kleaf), as expected, a higher RH reduces the vapor pressure difference across the boundary layer and therefore Jw(v) linearly decreases. Also, the elevated saturation vapor pressure at a higher temperature results in the larger evaporative flux. The impact of kleaf on the evaporative flux is clear in Fig. 2B, showing that Jw(v) is directly proportional to kleaf, as apparent from Eq. (4).
Evaporated water flux from leaves. (A) Evaporative water flux at leaves for different relative humidities and temperatures of the environment. Air velocity (U∞) of 1.4 m s−1 (= 5 km h−1) is considered. (Inset) Experimental measurement (symbols) and model prediction (Eq. (4), solid lines) of water vapor fluxes for the previously reported lab-scale artificial tree33. (B) Evaporative water flux for different solute concentrations in the feed water on the ground (at root) and mass transfer coefficients. Here, NaCl is assumed as feed solute, and relative humidity (RH) of 0.4 and T = 30 °C are considered. The dotted lines indicate the maximum treatable feed soulte concentration, which is determined by the corresponding leaf pore diameter, dleaf (Eq. 1), marked on the upper x-axis. For all calculations, leaf surface porosity (ε) of 0.4, length scale of the leaf surface (L) of 50 m, and feed flow velocity (U−∞) of 1 m s−1 are considered. As a reference, U∞ = 1.4 m s−1 and L = 50 m correspond to Shleaf = 6600.
Capillary pressure generated in leaf pores limits the treatable solute concentration of feed
The capillary pressure in the leaf must be sufficiently low to withdraw water from the feed by overcoming its osmotic pressure and to transport water through the stem by overcoming the viscous loss and hydrostatic pressure. The magnitude of capillary pressure increases as the pore size and the contact angle decrease (Eq. 1). Figure 2B also shows the achievable Jw(v) for different feed solute concentrations. The maximum leaf pore diameters (dleaf) that allow for dewatering of the corresponding feed concentrations are also shown. For example, dleaf < 10 nm would be required to overcome the osmotic pressure of 5 M NaCl feed.
It is worth noting that Jw(v) decreases with the feed concentration. The concave curvature of the meniscus in the leaf pore is associated with the depression of saturation vapor pressure on the leaf surface, PH(v)42,43, (Supplementary note S1), leading to decrease of Jw(v) (Eq. 4). This water vapor flux reduction due to the vapor pressure depression is more prominent for a larger Shleaf (i.e., larger kleaf). Given a feed solute concentration, the leaf pore diameter must be small enough to enable dewatering, but the vapor pressure depression reduces the water flux.
Water conduction through stem
Solute presence in the artificial xylem reduces the required magnitude of negative pressure and increases the maximum treatable solute concentration of feed
Liquid water at pressure below its saturation vapor pressure is in a metastable condition, and is prone to embolism28,29. Hence, artificial xylems are desired to be situated under a less negative pressure35. Rearranging Eq. (7) to: \(J_{w} = A_{m} \left[ {\left( {P_{a} - {\Pi }_{ - \delta } } \right) - \left( {P_{0} - {\Pi }_{0} } \right)} \right]\), it can be seen that increasing the osmotic pressure in the xylem (\({\Pi }_{0}\)) can allow for a higher P0 (i.e., less negative).
Figure 3A shows hydraulic or osmotic pressure values required for dewatering 1 M NaCl as a feed for different mean solute concentrations in xylem (\(\overline{C}_{X}\)). A small length of stem was considered (\(H = 1 \,\upmu {\text{m}}\)) to neglect any concentration polarization effect inside the xylem conduit, which is discussed in the next section. With \({\Pi }_{ - \delta } \approx {\Pi }_{ - \infty } \approx 50\,{\text{bar}}\) for 1 M NaCl feed, the magnitude of the negative pressure at the xylem-root membrane interface (P0) decreases as \(\overline{C}_{X}\) (and therefore \({\Pi }_{0}\)) increases. The maximum osmotic pressure of feed water that can be dewatered is the Laplace pressure added to \({\Pi }_{0}\) (i.e., \({\Pi }_{0} + \frac{{4\gamma \cos \theta_{min} }}{{d_{leaf} }}\)). Therefore, an increased xylem solute concentration (\(\overline{C}_{X}\)) provides more room to dewater the feed of a higher salinity. For example, when dleaf = 100 nm, the capillary pressure is not large enough to overcome the osmotic pressure of 1 M NaCl feed. However, dewatering of the feed becomes possible by having \(\overline{C}_{X}\) > 0.47 M NaCl. For dleaf = 30 nm, dewatering 1 M NaCl is possible even with pure water in the xylem, as \({\Pi }_{0} + \frac{{4\gamma \cos \theta_{min} }}{{d_{leaf} }} \approx 95 \,{\text{bar}} > {\Pi }_{ - \infty } \approx 50 \,{\text{bar}}\). But the maximum treatable solute concentration of the feed can be much more extended.
Effects of stem characteristics on water flow through artificial xylems. (A) Impact of solute concentration in the xylem on negative hydraulic pressure (− P0) and osmotic pressure (Π0) at the xylem-root membrane interface, and on maximum treatable osmotic pressures of feed (ΠF,−∞) for two different leaf pore diameters (dleaf). Shown as a dotted line, feed solute concentration (CF, −∞) of 1 M NaCl was used to calculate P0 and Π0. The shaded area indicates a feasible range of treatable feed osmotic pressure, which is, \(\approx {\Pi }_{0} + \frac{{4\gamma \cos \theta_{min} }}{{d_{leaf} }}\), where \(\theta_{min}\) is the receding contact angle in the leaf pore. For dleaf = 100 nm, \(\overline{C}_{X}\) > 0.47 M is required to recover water from the feed of 1 M NaCl. (B) Degree of concentration polarization in the xylem conduit determined by stem length (H) and xylem conduit diameter (dX). Concentration polarization factor (CPF) is defined as CPF ≡ (CX,H − CX,0)/ \(\overline{C}_{X}\). (C) Vapor pressure depressions on the leaf pore, due to the negative hydraulic pressure (blue shaded area) and the elevated osmotic pressure (red shaded area) by the concentration polarization in the xylem. The vapor pressure depressions are normalized to Psat0(T). The dotted line indicates 1 − RH, and the gap between the dotted line and the shaded areas represents the driving force for water vapor diffusion from the leaf surface to the ambient. Here, dX = 0.01 m is considered for the maximized concentration polarization, as shown in (B). For all calculations in (B) and (C), CF, −∞ = 1 M NaCl and \(\overline{C}_{X}\) = 0.5 mM are considered. AR is set as 100 to induce severe concentration polarization.
Solute presence in the xylem can result in severe concentration polarization
The upward water flow and the presence of solutes in the xylem inevitably causes concentration polarization, resulting in the highest solute concentration in the leaf pore (CX,H) and the lowest at the xylem-root membrane interface (CX,0) (Eqs. 8 and 9, and Fig. 1). This concentration polarization causes two negative effects: (1) reducing the osmotic pressure at the xylem-root membrane interface and therefore discounting its compensation effect on reducing the required magnitude of negative pressure; (2) increasing the solute concentration in the leaf pore, which causes the vapor pressure depression and therefore reduces the water vapor flux.
Here, a concentration polarization factor (CPF) is defined as the maximum solute concentration difference normalized by the mean concentration: \(CPF \equiv \frac{{C_{X,H} - C_{X,0} }}{{\overline{C}_{X} }}\). Figure 3B shows CPF values for different xylem conduit diameter (dX) and the stem length (H). The CPF values become very large for high H, due to the increased path length for diffusion. On the other hand, a larger dX incurs an enhanced Taylor dispersion that facilitates the solute diffusion44, leading to reduced CPF values. The reduced concentration polarization is more prominent when the water flux across the xylem is higher (Fig. S1). The effect of Taylor dispersion on enhancing water flux is discussed later in detail.
Severe concentration polarization results in vapor pressure depression, reducing the water flux
A saturation vapor pressure at the meniscus (\(P_{H}^{\left( v \right)}\)), higher than the partial vapor pressure in the ambient (\(P_{\infty }^{\left( v \right)}\)), drives the water vapor diffusion from the leaf surface to the ambient. While \(P_{\infty }^{\left( v \right)}\) is set by RH in the ambient, \(P_{H}^{\left( v \right)}\) decreases as the temperature decreases, the solute concentration in the liquid increases, and the hydraulic pressure of the liquid decreases (Supplementary note S1)42,43. When the liquid water in the leaf pore is at a largely negative pressure and exerts a large osmotic pressure due to the concentration polarization, PH(v) is depressed from Psat0(T), resulting in a reduced water flux. For \(\overline{C}_{X} = 0.5 \,{\text{mM}}\) and \(C_{F, - \infty } = 1M\), Fig. 3C depicts the vapor pressure depression normalized to Psat0(T), i.e., \(\frac{{P_{sat}^{0} \left( T \right) - P_{H}^{\left( v \right)} }}{{P_{sat}^{0} \left( T \right)}}\). It shows fractions of vapor pressure depression by the hydraulic pressure (blue shaded area) and by the osmotic pressure (red shaded area). With Psat0(T) being the maximum value of PH(v), 1 − RH represents the normalized maximum driving force for vapor diffusion, i.e., \(\frac{{P_{sat}^{0} \left( T \right) - P_{\infty }^{\left( v \right)} }}{{P_{sat}^{0} \left( T \right)}} = 1 - RH\). Owing to the need to overcome the feed osmotic pressure, the hydraulic pressure in the xylem conduit must be at least lower than − 50 bar for 1 M NaCl feed, which depresses ~ 5% of the vapor pressure at the meniscus. For a larger H, the solute concentration in the leaf pore increases due to a more severe concentration polarization, and the increased osmotic pressure at the leaf pore leads to a further vapor pressure depression. For instance, with \(H = 10 \,{\text{m}}\) and \(RH = 0.4\), the total vapor pressure depression accounts for ~ 30% of the maximum driving force (1 − RH), and a greater loss of driving force is expected for a higher RH.
Impact of root membranes on water transport
A high water permeability of root membrane marginally increases water flux, but significantly reduces the required magnitude of negative pressure
Given a water flux (Jw), a root membrane with lower water permeability poses a greater transport resistance of water, requiring a larger negative pressure at the xylem-root membrane interface (P0). Figure 4A, B show Jw and the required P0, respectively, for different water permeabilities of the root membrane (Am) and two different feed solute concentrations (CF, −∞). Leaf-to-root membrane area ratio (AR) of 100 is considered for a high flux of water withdrawn into the xylem conduit per given external conditions for evaporation. The dependency of water flux on Am is rather weak. With Am ~ O(1 kg m−2 h−1 bar−1 or L m−2 h−1 bar−1) for typical seawater RO membranes45, the water flux variation for Am in the range of 0.1–10 kg m−2 h−1 bar−1 does not exceed 10%.
Impact of water permeability of root membrane on water flux (A) and on negative pressure at the xylem-root membrane interface (B) for two different feed solute concentrations (CF, −∞) of 1 mM and 1 M NaCl. \(\overline{C}_{X}\) = 0.5 mM NaCl is considered such that the maximum concentration of solutes in the xylem does not exceed 5 M. And, dX = 0.01 m and AR = 100 are considered.
On the other hand, the magnitude of P0 increases by more than 60 bar when Am decreases from 1 to 0.1 kg m−2 h−1 bar−1 (Fig. 4B). The requirement of a larger pressure difference across a lower Am membrane demands a more negative pressure to be generated by the leaf pores, which in turn increases the cavitation risk in the artificial xylem. Therefore, Am values of commercial seawater RO membranes are well-suited for the root membranes without incurring a significant pressure drop.
A tight membrane is necessary to prevent severe concentration polarization in the xylem conduit
Due to the concentration polarization, it is desirable to prevent solute passage into the xylem, in particular when the stem length is large. In salt-rejecting membranes, a trade-off between water permeability and salt rejection is generally observed45. As previously discussed, a very tight (low Am and high rejection) membrane likely incurs highly negative pressure in the xylem. Nevertheless, commercial seawater RO membranes, with Am of ~ O(1 kg m−2 h−1 bar−1), can readily achieve > 99.9% rejection of monovalent salt (such as NaCl). Therefore, when artificial trees target dewatering of urban stormwater, which has typically low solute concentrations, the commonly available seawater RO membranes would suffice. When dewatering of industrial wastewater of high solute concentrations is aimed, higher salt rejecting membranes will be necessary.
Combined effects of structural properties on water flux
When external conditions such as temperature, air flow velocity, and RH are given, the water flux is mainly determined by combined effects of structural properties of the artificial tree. Fast dewatering requires a large leaf area for evaporation. In fact, the large canopy areas of trees per a given footprint is an integral element for tree-based urban stormwater control46. Figure 5A shows the water flux (Jw) dependency on the leaf-to-root membrane area ratio (AR) for the artificial xylem containing pure water (\(\overline{C}_{X} = 0\)) and 0.5 mM NaCl, with different xylem conduit diameters (dX) and the stem length (H) of 10 m. As anticipated, for \(\overline{C}_{X} = 0\) the water flux linearly increases with AR. When \(\overline{C}_{X} > 0\), however, the degree of water flux increase is reduced owing to the concentration polarization and the resulted vapor pressure depression at the leaf surface. This impact of concentration polarization on the water flux is gradually relieved by increasing the xylem conduit diameter. The degree of concentration polarization can be represented by the Péclet number, PeH:
where \(D_{eff} = D_{0} \left( {1 + Pe_{d}^{2} /196} \right)\) and \(Pe_{d} = \frac{{\overline{U}_{X} d_{X} }}{{D_{0} }}\)44. Figure 5B shows the changes in PeH as AR increases for different dX values. A large PeH implies a convective-dominant flow of solutes, leading to severe concentration polarization. In a low PeH flow, the diffusive flow counterbalances the convective flow, which deters the concentration polarization (Eq. 9) and is ideal to attaining high water fluxes. The impact of dX on PeH and therefore on the water flux can be illustrated from two extreme cases. For \(Pe_{d} \ll 1\) (\(d_{X} < \sim 0.01 {\text{m}}\)), PeH linearly increases with the water flow velocity in the xylem (\(\overline{U}_{X}\)) (Eq. 10a). In this case, a higher \(\overline{U}_{X}\) induces a more severe concentration polarization that in turn prevents enhancement of \(\overline{U}_{X}\); the enhancement of the water flux by increasing AR becomes smaller. At \(A_{R} = 100\), for instance, the water flux is ~ 24% less than that from no concentration polarization (dotted line in Fig. 5A), consistent with the reduced driving force by concentration polarization (Fig. 3C).
Impact of artificial tree structure on dewatering performance. (A) Water flux in the artificial tree for different values of leaf-to-root area ratio (AR ≡ Aleaf/Aroot) and xylem conduit diameter (dX). The dotted line shows water flux in the absence of solutes in the xylem, where the water flux is independent of value of dX. (B) Dependency of Péclet number (PeH) on AR and dX. A high PeH value implies severe concentration polarization in the xylem. For all calculations in (A) and (B), H = 10 m, CF, −∞ = 1 M, and \(\overline{C}_{X}\) = 0.5 mM are considered.
For \(Pe_{d} \gg 1\) (\(d_{X} \gg \sim 0.01 {\text{m}}\)), on the other hand, PeH is inversely proportional to \(\overline{U}_{X}\) (Eq. 10b); an increased flow velocity enhances Taylor dispersion, outweighing the convective flow. Therefore, an increased AR will result in a near-proportionally enhanced water flux (Fig. 5A) along with a deterred concentration polarization as represented by the low PeH (Fig. 5B). In these both cases of Ped, PeH increases with H, inducing a more severe concentration polarization. Nevertheless, for \(Pe_{d} \gg 1\), the concentration polarization can be alleviated by employing xylem conduits of a large diameter.
Design consideration and discussion
Several aspects of driving force, stability, and water flux for attaining effective nanocapillary-driven dewatering are discussed here. First, a sufficiently large negative pressure must be generated to uptake the water from the feed. A lack of driving force cannot lead to water uptake to the leaf pores, and result in drying of the leaf pores and failure of the dewatering process33. As the attainable maximum negative pressure is also determined by the receding contact angle (Eq. 1), a high hydrophilicity of the leaf capillary is essential. A suitable leaf capillary layer can be readily constructed using mesoporous hydrophilic materials47,48. In case pores are partially dried in such materials, a sizable transport resistance will be added due to the increased path length of vapor transport49,50,51 and will need to be considered for dewatering flow rate estimation. For pores of irregular shape, a geometrical factor should be considered when calculating the capillary pressure52. Additionally, it is noted that an increased humidity of the environment by temperature drop in the nocturnal period will likely induce water condensation on the leaf layer in particular when the saturation vapor pressure is depressed, corresponding to a concave curvature of meniscus in the hydrophilic leaf pore. As the excessive water on the leaf surface will evaporate, it would be practically less of a concern, but the water condensation may delay the onset of the dewatering process.
Second, the process stability will critically rely on the suppression of gas bubble formation and subsequent cavitation, as well as on the prevention of bubble expansion through the artificial xylem. As operated under negative pressures, natural trees are constantly at the risk of embolism of xylem conduits28,29. Their mechanism to repair xylem embolism is still unclear. However, an onset of cavitation may be deterred in artificial trees through several measures. The inner surface of artificial xylems must exhibit high hydrophilicity, which in turn elevates the free energy barrier for formation of bubble nuclei of critical size prior to an event of cavitation (Supplementary note S2 and Fig. S2)53. Likewise, any hydrophobic contaminants must not enter the artificial xylem conduits. A recent study revealed that an entrainment of naturally present lipids significantly increases the chance of cavitation in xylem conduits, due to the preferable bubble nuclei growth on the hydrophobic lipids54. For artificial trees, a water-permeable but highly solute-rejecting membrane is essential. Commercial seawater RO membranes effectively reject most of solutes, while exhibiting a sufficient water permeability. Also, the cavitation risk can be reduced by decreasing the necessary magnitude of negative pressure in the xylem. Use of saline solution in the artificial xylem will be an effective strategy for enhancing the stability (or preventing cavitation) when the stem length is small. For a ‘tall’ artificial tree, however, the presence of solutes would induce concentration polarization in the xylem conduit, which potentially negates the compensation effect of elevating the xylem osmotic pressure and results in a decreased water flux owing to the vapor-pressure depression.
In addition, dissolved air in the xylem conduit is another source for xylem embolism in natural trees52,55. When the temperature is lowered (e.g., a nocturnal period) and water evaporation is slow, the increased air solubility will likely induce dissolution of air into the artificial xylem through the leaf pores. As recently demonstrated by the author and colleagues, use of a tight hydrogel as the artificial leaf layer may be a suitable strategy to prevent air dissolution while still generating large negative pressures.
It is worth mentioning that natural trees possess a xylem system consisting of segmented conduits, working as a safety device, which ensures water transport even when embolism occurs56,57. The conduit segments (tracheids and vessels) are connected to the neighboring segments through finely porous pit membranes58. In the event of embolism, the pit membranes allow for local confinement of the bubble in that segment, and prevents the bubble from spreading to the entire xylem network59,60. Although in the present study straight cylindrical pores were considered for artificial xylem, water conduits with the small segments delineated with nanoporous membranes, resembling the xylem structure in natural trees, will improve the stability of the dewatering process. Nevertheless, the improved stability will be achieved at the cost of increased hydraulic resistances.
Third, increasing the leaf area for evaporation is a straightforward approach to enable a high water flux (Fig. 5). As shown in the current example of an artificial-tree-transformed-building, a larger leaf surface on the building wall and roof-top surface would be attainable for a taller building with a given footprint on the ground. Even for a 50 story-building (~ 150 m tall), the additional negative pressure required for the water pumping is ~ 15 bar, which can be achieved by employing nanocapillaries with a diameter of ~ O(10 nm). A greater leaf area exposed to the air can further be obtained by increasing the surface roughness. To put into perspective, the transpiration rate by natural trees ranges from 10 to 200 kg day−1 tree−146,61. Assuming 50 m2 ground footprint for a single urban tree, an artificial tree occupying the equivalent footprint can enable ~ 500 kg day−1 for AR of 20 and 6 h of solar irradiation (Fig. 5). An expanded root area by increasing roughness or multiple root ‘branches’ would also enhance the dewatering rate, which would particularly be relevant to the water removal from tailing ponds, concentrating brines for metal recovery, or solar desalination of seawater35.
It should be mentioned that although this capillary-driven dewatering is a passive process without requiring any mechanical pumping, the evaporative water flux is essentially limited by the solar energy and heat transferred from the environment. As such, a leaf layer that can effective absorb solar irradiation would further enhance the dewatering rate. For instance, photothermally engineered materials can allow for effective absorption of solar irradiation in a wide wavelength range62.
When potentially implemented, this tree-mimicking dewatering requires further considerations of realistic air flows and heat transfer in the environment. In this paper, a single-standing artificial tree was considered for simplicity of analysis. However, when there are multiple artificial trees (for instance, aiming for a Sponge City33), the interference of air flows with multiple structures would need to be accounted to estimate the more accurate dewatering rate. Also in other cases such as dewatering of tailing ponds, geographical influence on the air flow would need to be considered. Additionally, the directions and intensity of solar irradiation as well as air flow velocity and humidity have the determining role on the dewatering rate. Hence, for such a large-scale implementation, sophisticated weather models will be necessary to predict the performance.
References
Powers, J. P. Construction Dewatering and Groundwater Control: New Methods and Applications 3rd edn. (Wiley, 2007).
Cashman, P. M. & Preene, M. Groundwater Lowering in Construction: A Practical Guide to Dewatering 3rd edn. (CRC Press, 2020).
Bonaui, C. et al. Food drying and dewatering. Dry. Technol. 14, 2135–2170. https://doi.org/10.1080/07373939608917199 (1996).
Petrotos, K. B. & Lazarides, H. N. Osmotic concentration of liquid foods. J. Food Eng. 49, 201–206. https://doi.org/10.1016/S0260-8774(00)00222-3 (2001).
Flexer, V., Baspineiro, C. F. & Galli, C. I. Lithium recovery from brines: a vital raw material for green energies with a potential environmental impact in its mining and processing. Sci. Total Environ. 639, 1188–1204. https://doi.org/10.1016/j.scitotenv.2018.05.223 (2018).
Buckwalter, P., Embaye, T., Gormly, S. & Trent, J. D. Dewatering microalgae by forward osmosis. Desalination 312, 19–22. https://doi.org/10.1016/j.desal.2012.12.015 (2013).
Bhave, R., Kuritz, T., Powell, L. & Adcock, D. Membrane-based energy efficient dewatering of microalgae in biofuels production and recovery of value added co-products. Environ. Sci. Technol. 46, 5599–5606. https://doi.org/10.1021/es204107d (2012).
Neyens, E., Baeyens, J., Dewil, R. & De Heyder, B. Advanced sludge treatment affects extracellular polymeric substances to improve activated sludge dewatering. J. Hazard. Mater. 106, 83–92. https://doi.org/10.1016/j.jhazmat.2003.11.014 (2004).
Qi, Y., Thapa, K. B. & Hoadley, A. F. A. Application of filtration aids for improving sludge dewatering properties—a review. Chem. Eng. J. 171, 373–384. https://doi.org/10.1016/j.cej.2011.04.060 (2011).
Gumfekar, S. P., Rooney, T. R., Hutchinson, R. A. & Soares, J. B. P. Dewatering oil sands tailings with degradable polymer flocculants. ACS Appl. Mater. Interfaces 9, 36290–36300. https://doi.org/10.1021/acsami.7b10302 (2017).
Natural Resources Defense Council and Environmental Defence. One trillion litres of toxic waste and growing: Alberta’s tailings ponds. https://environmentaldefence.ca/report/albertas-tailings-ponds/ (2017).
ten Veldhuis, J. A. E., Clemens, F. H. L. R., Sterk, G. & Berends, B. R. Microbial risks associated with exposure to pathogens in contaminated urban flood water. Water Res. 44, 2910–2918. https://doi.org/10.1016/j.watres.2010.02.009 (2010).
Hammond, M. J., Chen, A. S., Djordjevic, S., Butler, D. & Mark, O. Urban flood impact assessment: a state-of-the-art review. Urban Water J. 12, 14–29. https://doi.org/10.1080/1573062x.2013.857421 (2015).
Razmjou, A., Liu, Q., Simon, G. P. & Wang, H. T. Bifunctional polymer hydrogel layers as forward osmosis draw agents for continuous production of fresh water using solar energy. Environ. Sci. Technol. 47, 13160–13166. https://doi.org/10.1021/es403266y (2013).
Taiz, L. & Zeiger, E. Plant Physiology 4th edn. (Sinauer Associates, 2006).
Schlesinger, W. H. & Jasechko, S. Transpiration in the global water cycle. Agric. For. Meteorol. 189, 115–117. https://doi.org/10.1016/j.agrformet.2014.01.011 (2014).
Pickard, W. F. The ascent of sap in plants. Prog. Biophys. Mol. Biol. 37, 181–229. https://doi.org/10.1016/0079-6107(82)90023-2 (1981).
Tyree, M. T., Zimmermann, M. H. & Zimmermann, M. H. Xylem Structure and the Ascent of Sap 2nd edn. (Springer, 2002).
Stroock, A. D., Pagay, V. V., Zwieniecki, M. A. & Holbrook, N. M. The physicochemical hydrodynamics of vascular plants. Annu. Rev. Fluid Mech. 46, 615–642. https://doi.org/10.1146/annurev-fluid-010313-141411 (2014).
Venturas, M. D., Sperry, J. S. & Hacke, U. G. Plant xylem hydraulics: what we understand, current research, and future challenges. J. Integr. Plant Biol. 59, 356–389. https://doi.org/10.1111/jipb.12534 (2017).
Tyree, M. T. The ascent of water. Nature 423, 923–923. https://doi.org/10.1038/423923a (2003).
Reef, R. & Lovelock, C. E. Regulation of water balance in mangroves. Ann. Bot. Lond. 115, 385–395. https://doi.org/10.1093/aob/mcu174 (2015).
Martinez-Ballesta, M. D. C., Silva, C., Lopez-Berenguer, C., Cabanero, F. J. & Carvajal, M. Plant aquaporins: new perspectives on water and nutrient uptake in saline environment. Plant Biol. 8, 535–546. https://doi.org/10.1055/s-2006-924172 (2006).
Yang, Y., Park, J., Kwon, S. H. & Kim, Y. S. Fluidic active transducer for electricity generation. Sci. Rep. https://doi.org/10.1038/srep15695 (2015).
Borno, R. T., Steinmeyer, J. D. & Maharbiz, M. M. Charge-pumping in a synthetic leaf for harvesting energy from evaporation-driven flows. Appl. Phys. Lett. https://doi.org/10.1063/1.3157144 (2009).
Goedecke, N., Eijkel, J. & Manz, A. Evaporation driven pumping for chromatography application. Lab Chip 2, 219–223. https://doi.org/10.1039/b208031c (2002).
Walker, G. M. & Beebe, D. J. An evaporation-based microfluidic sample concentration method. Lab Chip 2, 57–61. https://doi.org/10.1039/b202473j (2002).
Tyree, M. T. & Sperry, J. S. Vulnerability of xylem to cavitation and embolism. Annu. Rev. Plant Phys. 40, 19–38. https://doi.org/10.1146/annurev.pp.40.060189.000315 (1989).
Duan, C., Karnik, R., Lu, M. C. & Majumdar, A. Evaporation-induced cavitation in nanofluidic channels. Proc. Natl. Acad. Sci. USA 109, 3688–3693. https://doi.org/10.1073/pnas.1014075109 (2012).
Walker, G. M. & Beebe, D. J. A passive pumping method for microfluidic devices. Lab Chip 2, 131–134. https://doi.org/10.1039/b204381e (2002).
Wheeler, T. D. & Stroock, A. D. The transpiration of water at negative pressures in a synthetic tree. Nature 455, 208–212. https://doi.org/10.1038/nature07226 (2008).
Vincent, O., Szenicer, A. & Stroock, A. D. Capillarity-driven flows at the continuum limit. Soft Matter 12, 6656–6661. https://doi.org/10.1039/c6sm00733c (2016).
Wang, Y. K., Lee, J., Werber, J. R. & Elimelech, M. Capillary-driven desalination in a synthetic mangrove. Sci. Adv. https://doi.org/10.1126/sciadv.aax5253 (2020).
Tong, T. & Elimelech, M. The global rise of zero liquid discharge for wastewater management: drivers, technologies, and future directions. Environ. Sci. Technol. 50, 6846–6855. https://doi.org/10.1021/acs.est.6b01000 (2016).
Mi, B. X., Finnerty, C. & Conway, K. Prospects of artificial tree for solar desalination. Curr. Opin. Chem. Eng. 25, 18–25. https://doi.org/10.1016/j.coche.2019.06.004 (2019).
Lee, J., Laoui, T. & Karnik, R. Nanofluidic transport governed by the liquid/vapour interface. Nat. Nanotechnol. 9, 317–323. https://doi.org/10.1038/Nnano.2014.28 (2014).
Hoch, G., Chauhan, A. & Radke, C. J. Permeability and diffusivity for water transport through hydrogel membranes. J. Membr. Sci. 214, 199–209. https://doi.org/10.1016/S0376-7388(02)00546-X (2003).
Nobel, P. S. Physicochemical and Environmental Plant Physiology 3rd edn. (Elsevier Academic Press, 2005).
Baker, R. W. 1 Online Resource (Wiley, 2012).
Moin, P. Fundamentals of Engineering Numerical Analysis 2nd edn. (Cambridge University Press, 2010).
Huang, H. & Haghighat, F. Modelling of volatile organic compounds emission from dry building materials. Build. Environ. 37, 1127–1138. https://doi.org/10.1016/S0360-1323(01)00089-0 (2002).
Lee, J., Straub, A. P. & Elimelech, M. Vapor-gap membranes for highly selective osmotically driven desalination. J. Membr. Sci. 555, 407–417. https://doi.org/10.1016/j.memsci.2018.03.059 (2018).
Wex, H., Stratmann, F., Topping, D. & McFiggans, G. The Kelvin versus the Raoult term in the Kohler equation. J. Atmos. Sci. 65, 4004–4016. https://doi.org/10.1175/2008jas2720.1 (2008).
Brenner, H. & Edwards, D. A. Macrotransport Processes (Butterworth-Heinemann, 1993).
Werber, J. R., Deshmukh, A. & Elimelech, M. The critical need for increased selectivity, not increased water permeability, for desalination membranes. Environ. Sci. Technol. Lett. 3, 112–120. https://doi.org/10.1021/acs.estlett.6b00050 (2016).
Berland, A. et al. The role of trees in urban stormwater management. Landsc. Urban Plan 162, 167–177. https://doi.org/10.1016/j.landurbplan.2017.02.017 (2017).
Titirici, M. M., Thomas, A. & Antonietti, M. Aminated hydrophilic ordered mesoporous carbons. J. Mater. Chem. 17, 3412–3418. https://doi.org/10.1039/b703569a (2007).
Ren, Y., Ma, Z. & Bruce, P. G. Ordered mesoporous metal oxides: synthesis and applications. Chem. Soc. Rev. 41, 4909–4927. https://doi.org/10.1039/c2cs35086f (2012).
Vaartstra, G. et al. Capillary-fed, thin film evaporation devices. J. Appl. Phys. https://doi.org/10.1063/5.0021674 (2020).
Rangharajan, K. K., Sundaram, P. M., Conlisk, A. T. & Prakash, S. Surface dependent enhancement in water vapor permeation through nanochannels. Analyst https://doi.org/10.1039/c8an00650d (2018).
Li, R., Wang, J. & Xia, G. New model for liquid evaporation and vapor transport in nanopores covering the entire Knudsen regime and arbitrary pore length. Langmuir 37, 2227–2235. https://doi.org/10.1021/acs.langmuir.1c00023 (2021).
Schenk, H. J., Steppe, K. & Jansen, S. Nanobubbles: a new paradigm for air-seeding in xylem. Trends Plant Sci. 20, 199–205. https://doi.org/10.1016/j.tplants.2015.01.008 (2015).
Holtta, T., Vesala, T., Peramaki, M. & Nikinmaa, E. Relationships between embolism, stem water tension, and diameter changes. J. Theor. Biol. 215, 23–38. https://doi.org/10.1006/jtbi.2001.2485 (2002).
Kanduc, M. et al. Cavitation in lipid bilayers poses strict negative pressure stability limit in biological liquids. Proc. Natl. Acad. Sci. USA 117, 10733–10739. https://doi.org/10.1073/pnas.1917195117 (2020).
Pickard, W. F. & Melcher, P. J. in Vascular Transport in Plants (eds N. Michele Holbrook & M. A. Zwieniecki) 3–18 (Academic Press, 2005).
Loepfe, L., Martinez-Vilalta, J., Pinol, J. & Mencuccini, M. The relevance of xylem network structure for plant hydraulic efficiency and safety. J. Theor. Biol. 247, 788–803. https://doi.org/10.1016/j.jtbi.2007.03.036 (2007).
Schenk, H. J. et al. Hydraulic integration and shrub growth form linked across continental aridity gradients. Proc. Natl. Acad. Sci. USA 105, 11248–11253. https://doi.org/10.1073/pnas.0804294105 (2008).
Choat, B., Cobb, A. R. & Jansen, S. Structure and function of bordered pits: new discoveries and impacts on whole-plant hydraulic function. New Phytol. 177, 608–625. https://doi.org/10.1111/j.1469-8137.2007.02317.x (2008).
Kaack, L. et al. Function and three-dimensional structure of intervessel pit membranes in angiosperms: a review. Iawa J. 40, 673–702. https://doi.org/10.1163/22941932-40190259 (2019).
Zhang, Y. et al. High porosity with tiny pore constrictions and unbending pathways characterize the 3D structure of intervessel pit membranes in angiosperm xylem. Plant Cell Environ. 43, 116–130. https://doi.org/10.1111/pce.13654 (2020).
Vose, J. M., Harvey, G. J., Elliott, K. J. & Clinton, B. D. Measuring and modeling tree and stand level transpiration. Phytoremediation https://doi.org/10.1002/047127304X.ch8 (2003).
Wang, P. Emerging investigator series: the rise of nano-enabled photothermal materials for water evaporation and clean water production by sunlight. Environ. Sci. Nano https://doi.org/10.1039/C8EN00156A (2018).
Acknowledgements
The author acknowledges the funding support from Natural Sciences and Engineering Research Council of Canada (NSERC) through the Discovery Grant.
Author information
Authors and Affiliations
Contributions
J.L. conducted the modelling, Matlab code development, analysis and manuscript writing.
Corresponding author
Ethics declarations
Competing interests
The author declares no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Lee, J. Perspectives and design considerations of capillary-driven artificial trees for fast dewatering processes. Sci Rep 11, 8631 (2021). https://doi.org/10.1038/s41598-021-88006-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-021-88006-z
- Springer Nature Limited
This article is cited by
-
Interfacial solar evaporation for zero liquid discharge desalination
Communications Materials (2024)