Abstract
This study assessed the possibility of semi-automatic harmonization of standardized uptake values (SUVs) in multicenter studies. Phantom data were acquired using 16 PET/CT scanners (including 3 PET/CT scanners with a silicon photomultiplier detector). PET images obtained using 30-min/bed scans for optimum harmonization filter calculations and using 90–180-s/bed scans for SUV validation under clinical conditions were obtained. Time of flight and a reconstruction method with point-spread function correction were allowed. The optimal full width at half maximum of the 3D-Gaussian filter that minimizes the root mean square error with the median value of the JSNM harmonization range was calculated semi-automatically. The SUVmax and the SUVpeak of the hot spheres were measured, and the inter-scanner coefficient of variation (COV) was calculated before and after harmonization. The harmonization filter was applied to 11 of the 15 PET/CT scanners in which the SUV calibration accuracy had been verified, but not in the remaining 4 scanners. Under noiseless conditions before harmonization, the inter-scanner COVs of the SUVmax and the SUVpeak were as high as 21.57% and 12.20%, respectively, decreasing to 8.79% and 5.73% after harmonization, respectively. Harmonization brought the SUVmax of all the hot spheres to within the harmonization range. Even under clinical conditions affected by image noise, the inter-scanner COVs for the SUVmax and SUVpeak were as high as 8.83% and 5.18% after harmonization, respectively. By applying an optimal harmonization filter that is calculated semi-automatically, the harmonization of SUVs according to the JSNM strategy is possible in multicenter studies, thereby reducing inter-scanner COVs.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
Positron emission tomography (PET)/computed tomography (CT) using 2-deoxy-2-(18F)fluoro-D-glucose (FDG) is useful for the initial diagnosis, staging, restaging, monitoring, and prediction of prognosis of various types of tumors1,2,3. Quantitative PET evaluations are generally performed using the standardized uptake value (SUV). By defining two-dimensional (2D) regions of interest (ROIs) or three-dimensional (3D) volumes of interest (VOIs) on PET images, various types of SUVs can be calculated automatically as follows: the SUVmax, which is the maximum value in the ROI; the SUVpeak, which is the average value in a local area of 1 cm3 surrounding the voxel with the maximum tracer uptake; and the SUVmean, which is the average SUV calculated from voxels that exceed a particular SUV threshold. The SUVmax is the most frequently used parameter in clinical settings because of a good inter-observer agreement and robustness against a partial volume effect (PVE). On the other hand, the SUVmax is susceptible to an upward bias arising from image noise, which can easily fluctuate depending on the PET scanners and protocols that are used. Lodge et al. reported that the SUVpeak is more robust to image noise than the SUVmax in PET images4. However, the SUVpeak can exhibit a large variation because of the ambiguous definition of its measuring method, and this may influence the assessment of responses to therapy5. Recently, the Quantitative Imaging Biomarker Alliance (QIBA) defined a method for calculating SUVpeak6. For the SUVpeak measure, it is necessary to automatically and reproducibly detect the place where the mean value in the 1 cm3 region is the highest within the placed VOI. Therefore, a strategy for standardizing methods of calculating the SUV is necessary to validate PET/CT as a quantitative tool and the SUV as an imaging biomarker7.
To facilitate multicenter studies using FDG-PET, EANM Research Ltd. (EARL) previously reported the upper and lower limits of the recovery coefficient and proposed the concept of “harmonization of SUVs”8. Considering recent technological innovations, such as new reconstruction technologies (i.e., point spread function [PSF]) and the practical application of semiconductor PET/CT using silicon photomultiplier (SiPM) detectors, an additional filter, known as a harmonization filter, could be applied for SUV harmonization9. The use of a software tool (EQ.PET) that harmonizes SUVs among different PET systems has highlighted the possibility of SUV harmonization using a harmonization filter, suggesting the possibility of both good tumor detectability and quantitative harmonization10. Generally, a 3D-Gaussian filter is used as a harmonization filter for software with a harmonizing function, and the parameters provided by the full width at half maximum (FWHM) must be changed to adjust the SUV. Lasnon et al. reported that SUV harmonization according to the EARL strategy is possible in multicenter studies by optimizing the FWHM of the 3D-Gaussian filter based on the root mean square error (RMSE) for the target SUV using phantom data11.
In the J-Hart study conducted in Japan, Tsutsui et al. set the SUVmax calculated by applying a 3D-Gaussian filter of 10 mm at FWHM to a Digital Reference Object (DRO) created by QIBA as the target of harmonization; in this manner, they showed that the harmonization of quantitative values is possible using phantom data acquired in a multicenter study12. The Japanese Society of Nuclear Medicine (JSNM) has established a phantom test method in which the upper and lower limits of the SUVmax are described for the purpose of harmonizing quantitative values in multicenter studies13. Daisaki et al. reported a multicenter study of malignant lymphoma that adopted a standardization process for image quality in accordance with the JSNM guidelines before the harmonization strategy was proposed14. Since then, no reports have been found in Japan regarding multicenter studies focusing on quantitative evaluations involving the application of JSNM's harmonization strategy.
We attempted to harmonize SUVs according to JSNM's strategy using a semi-automatic harmonization method in a multicenter study. We also examined the reproducibility of quantitative indicators (SUVmax and SUVpeak) in PET images under clinical conditions affected by image noise.
Materials and methods
Ethics
The phantom data used in this study were obtained for a retrospective multicenter study of the assessing treatment effects and the prediction of treatment effect of immune checkpoint inhibitors. The clinical PET images presented in this paper are from a study approved by ethics committee of the Hyogo College of Medicine (No. 3315), which waived the requirement for informed consent. This study was conducted in accordance with the Declaration of Helsinki and Ethical Guidelines for Medical and Health Research Involving Human Subjects.
Phantom data for harmonization
PET images were acquired from 16 PET/CT scanners in 8 institutions, including 3 PET/CT scanners equipped with SiPM detectors. According to the JSNM guidelines, a radioactivity of 18F solution (Hot:BG ratio of 4:1 for all PET/CT scanners) determined according to the injection dose of each institution was enclosed in the image quality phantom15 (Table 1). To check the cross-calibration accuracy, the average SUV in the phantom BG region was measured using 12 ROIs with a diameter of 37 mm and was verified to be within the range of 1.00 ± 0.05. One PET/CT scanner was excluded from this study because the average SUV showed a low value beyond the acceptable range.
All the PET emission data were acquired using a 30 min/bed scan in 3D list-mode. CT data were also acquired using each institution’s default parameters and were used for attenuation correction of the PET images. The list-mode data for the 30 min/bed scans were reconstructed using each institution’s default parameters for optimal harmonization filter calculations. Table 1 shows the image reconstruction method and parameters for each scanner. In this study, PSF correction for superior lesion detectability was allowed throughout the image reconstruction process.
Semi-automatic SUV harmonization method
As shown in Fig. 1, the RC Tool for Harmonization (Nihon Medi-Physics Co., Ltd.) was used to set the ROI at the same size as the diameters of all the hot spheres and to calculate the SUVmax. The optimum FWHM of the harmonization filter was defined as the value that minimizes the RMSE calculated using Eq. (1).
Here, targetSUVmax was the median value of the harmonization range defined in the JSNM guidelines. The filterSUVmax was measured using a PET image with a 3D-Gaussian filter applied to the PET image with the default parameters of each institution, and the 3D-Gaussian filter was incremented by 1 mm from 2 to 10 mm at FWHM. In addition, when the RMSE for the last 3 mm recorded an increase, the FWHM increment to be applied was terminated. Subsequently, the RMSE was calculated in 0.1 mm increments within the range of ± 1 mm of the FWHM value that achieved a minimum RMSE value in 1-mm increments (Fig. 2). The FWHM of the optimum harmonization filter with one decimal place was automatically displayed in the RC Tool for Harmonization. When the RMSE increased by applying the 3D-Gaussian filter, compared with the RMSE calculated using each institution’s default parameter, N/A was displayed in the RC Tool for Harmonization, and the PET image without the harmonization filter was judged to be optimal.
Coefficient of variation (COV) among scanners
The list-mode PET emission data was re-binned according to the acquisition duration used clinically, and image reconstruction was performed using each institution’s default reconstruction parameters. The SUVmax and SUVpeak were calculated before and after harmonization using both PET images from the 30 min/bed scan, which is less affected by image noise, and those obtained using the clinical acquisition duration typically used at each institution. The SUVs were calculated by setting a VOI of the same size as each hot sphere using RAVAT (Nihon Medi-Physics Co., Ltd.), which is a PET quantitative analysis software for research that is compliant with the QIBA profile (Fig. 3). The SUVpeak of the hot sphere was measured except for 10 mm (taking into account the measurement definition). The differences between the scanners before and after harmonization were evaluated using the COV shown in Eq. (2).
Results
Changes in RMSE according to changes in FWHM produced by additional 3D-Gaussian filters
Figure 4 shows the RMSE when the 3D-Gaussian filter was changed in increments from 2 to 10 mm. By applying the optimization strategy of the 3D-Gaussian filter using the RC Tool for Harmonization, the optimum FWHM of the harmonization filter producing the lowest RMSE value was determined for 11 of the 15 scanners in which the SUV calibration accuracy had been verified. The remaining 4 scanners had the lowest RMSE in each institution’s default PET images in which a 3D-Gaussian filter was not applied.
SUVmax and SUVpeak before and after harmonization
Figure 5a, b respectively show the SUVmax and the SUVpeak calculated for the PET images reconstructed according to each institution’s default parameters for the 30 min/bed (noiseless conditions) scans. For SUVmax, the COVs of the differences among the scanners were 21.57%, 20.49%, 14.4%, 8.24%, 4.71%, and 3.13% for the 10-, 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively. For the SUVpeak, the COVs were 12.20%, 12.71%, 9.41%, 5.76%, and 3.29% for the 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively.
(a) SUVmax and (b) SUVpeak under each institution’s reconstruction parameters and noiseless conditions. The solid red lines show the upper and lower limits of the SUVmax defined according to the JSNM guidelines. Some scanners had an SUVmax that was higher than the upper limit. The harmonization range of the SUVpeak is not defined in the JSNM guidelines. The actual values obtained using each scanner are shown in Online Resource 1 (SUVmax) and Online Resource 2 (SUVpeak).
Figure 6a, b respectively show the harmonized SUVmax and harmonized SUVpeak calculated for the PET images obtained during the 30 min/bed scans after the application of the optimal 3D-Gaussian filter derived from the RC Tool for Harmonization. The SUVmax for all the hot spheres of all the scanners fell within the JSNM’s harmonization range. For the harmonized SUVmax, the COVs of the differences among the scanners were 8.79%, 8.54%, 6.34%, 4.60%, 6.63%, and 6.37% for the 10-, 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively. For the harmonized SUVpeak, the COVs were 5.73%, 5.23%, 3.31%, 3.04%, and 3.03% for the 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively.
(a) Harmonized SUVmax and (b) harmonized SUVpeak after the addition of an optimal harmonization filter under noiseless conditions. The solid red lines show the upper and lower limits of the SUVmax defined according to the JSNM guidelines. The harmonized SUVmax were within the harmonization range of the JSNM guidelines for all the scanners. The actual values obtained using each scanner are shown in Online Resource 3 (harmonized SUVmax) and Online Resource 4 (harmonized SUVpeak).
Figure 7a, b respectively show the harmonized SUVmax and harmonized SUVpeak calculated for PET images obtained using the acquisition duration typically used for clinical studies at each institution. For the harmonized SUVmax, the COVs of the differences among the scanners were 8.83%, 8.32%, 4.68%, 7.65%, 4.45%, and 5.68% for the 10-, 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively. For the harmonized SUVpeak, the COVs were 5.18%, 4.85%, 6.35%, 3.43%, and 3.75% for the 13-, 17-, 22-, 28-, and 37-mm hot spheres, respectively.
(a) Harmonized SUVmax and (b) harmonized SUVpeak after the addition of an optimal harmonization filter under clinical conditions. The harmonized SUVmax measured using PET images under clinical conditions exceeded the JSNM upper limits for the 22-mm, 28-mm, and 37-mm hot spheres on some scanners. The actual values obtained using each scanner are shown in Online Resource 5 (harmonized SUVmax) and Online Resource 6 (harmonized SUVpeak).
The actual SUVmax, SUVpeak, and optimal harmonization filters calculated for each PET/CT scanner are shown in the online resources (1–6).
Clinical images with or without additional harmonization filter
The PET images before and after applying the harmonization filter with FWHM = 5.8 mm were shown in Fig. 8. The quantitative values of the primary breast cancer were SUVmax = 9.14, SUVpeak = 7.30 before the harmonization, and SUVmax = 8.11, SUVpeak = 6.98 after the harmonization. Since the resolution of PET images is usually reduced by the harmonization, the edges of the lesions are slightly blurred (the area within the red dotted line), but the detection rate of lesions is not significantly affected in this patient.
A case with accumulation of FDG in the right primary breast cancer and metastatic lymph nodes. Maximum intensity projection images (left column) and fused PET/CT images (right column) before and after harmonization are shown. The fused images show quantitative values calculated by applying a threshold of 40% to VOI using RAVAT for right primary breast cancer lesions.
Discussion
In this study, we investigated whether harmonization strategy defined by JSNM could be applied to heterogenous multicenter studies involving PET/CT scanners of different generations including SiPM PET/CT scanners. First, to perform harmonization with a high reproducibility and objectivity, the optimum FWHM of the 3D-Gaussian filter for harmonization was calculated semi-automatically using the RC Tool for Harmonization targeting the median value of the harmonization range specified by the JSNM13. Next, if necessary, the optimal harmonization filter was applied to PET images having different degrees of image noise that had been reconstructed using each institution’s default reconstruction parameters.
The SUVmax measured using each institution’s default reconstruction parameters were not included in the harmonization range of the JSNM strategy for 10 of the 15 PET/CT scanners. This multicenter study included both conventional PET/CT scanners with PMT detectors and semiconductor PET/CT scanners with SiPM detectors. Some of the included PET/CT scanners used an image reconstruction method with PSF correction, which helps to improve lesion detectability. However, PSF correction can also result in an overestimation of the SUV because of edge artifacts (or Gibbs artifacts)16. Thus, the JSNM’s current harmonization strategy is defined based on PET image data from multicenter studies without PSF correction. PET images obtained using the image reconstruction parameters typically used clinically at each institution are often ineligible for quantitative evaluations in multicenter studies. In the present study, we determined that all the SUVmax that were originally judged to be ineligible according to the JSNM harmonization strategy could be included in the defined range by applying the optimal harmonization filter that was semi-automatically calculated using the research software RC Tool for Harmonization. Furthermore, harmonization decreased the maximum COV of the SUVmax among the PET/CT scanners from 21.57 to 8.79% at a 10-mm hot sphere. Harmonization also decreased the maximum COV of the SUVpeak from 12.71% at a 17-mm hot sphere to 5.73% at a 13-mm hot sphere. Tsutsui et al. reported the J-Hart study, which attempted to harmonize 12 PET/CT scanners using the target SUVmax calculated by a DRO, and the FWHM of the optimum harmonization filter was calculated for each scanner by changing the 3D-Gaussian filter by 1 mm12. In their study, a maximum COV of 10.7% was observed for a 13-mm sphere even after harmonization. In the present study, however, the COV was less than 10% despite the more heterogeneous multicenter study design and the inclusion of semiconductor PET/CT scanners. This reduction in COV may be due to the fact that the RC Tool for Harmonization semi-automatically optimizes the harmonization filter in units of 0.1 mm. Furthermore, in the present study, the SUVpeak was also measured based on the QIBA’s measurement principle and a better COV of 5.73%, compared with the SUVmax, was achieved.
In this study, we also estimated the practical differences among PET/CT scanners under clinical conditions by applying a calculated optimum harmonization filter to PET images obtained using the clinical acquisition duration typically used at each institution. Although the harmonized SUVmax showed that the results for hot spheres of 22–37 mm in diameter fell outside the harmonization range because of the influence of an upward bias caused by image noise, the COV was within 10% (highest value was 8.83% for a 10-mm hot sphere), which was comparable to the COVs (highest value of 8.79% for a 10-mm hot sphere) of harmonized SUVmax based on PET images obtained under noiseless conditions. The maximum COV of the harmonized SUVpeak calculated from PET images obtained under clinical conditions was 6.35%, which was lower than the COV of the harmonized SUVmax. In other words, quantitative multicenter studies with acceptable inter-scanner variability could be feasible if software-based harmonization method and SUVpeak quantification are applied.
The reproducibility of analyses and analysis software is important in quantitative studies involving the analysis of PET images. In the past, ambiguities in calculation processes have been problematic when a SUVpeak was recommended, instead of the noise-sensitive SUVmax5. Specifically, whether the pixel for the SUVmax calculation should be the center of the SUVpeak measurement or whether the SUVpeak should be the output after searching for the region where the SUVpeak was highest in all places within the tumor is unclear. In the harmonization process as well, a clear objective definition and a high reproducibility are required when applying a harmonization filter. The RC Tool for Harmonization used in this study uses 1-mm increments in the range of 0–20 mm to identify the minimum RMSE value and then calculates the RMSE in 0.1-mm increments within the minimum value ± 1 mm range. In the present study, detailed harmonization filter optimization was possible by finding the minimum RMSE value. Of note, this process is highly reproducible and has the clarity of the derivation process of RMSE-based optimization, as there are no manual interventions by the analyst.
Although not found in this study, if the SUVmax calculated in the PET image with before harmonization falls below the lower limit of the harmonization range, it is necessary to reconsider the image reconstruction condition (generally, iteration, subset and filter). Furthermore, if there is an event, such as changing acquisition and image reconstruction parameters, upgrading software, reducing the sensitivity of PET/CT scanner and the accompanying overhaul, etc., that affects the image quality or quantitative accuracy of the original PET image, it is necessary to re-verify whether SUVmax is within the harmonization range. Thus, the constancy of PET images needs to be checked at regular basis. The presence of a centralized analysis laboratory in a multicenter PET study should be expected to yield better results for SUV harmonization and also helps to provide quality assurance that is important for clinical research.
JSNM defines physical image quality standards (e.g., CV < 10%) for determining imaging conditions in the JSNM guidelines, mainly to improve the quality of clinical research and clinical trials. The phantom data of this study was acquired based on the clinical routine protocol of each institution, except for the calculation of the optimal harmonization filter. As a result, even though the model were the same (e.g., Discovery MI 4R No. 1 and No. 2 in this study), one could be harmonized appropriately, while another could not. Moreover, as shown in Fig. 7a, the curve of SUVmax can fluctuate up and down unstably even after the harmonization. Since this phenomenon was not observed in the PET image with sufficient acquisition duration as shown in Fig. 5a, the fluctuation of the curve might have caused by a statistical noise. In the harmonization method using post filtering, the quantitative value may fluctuate depending on the quality of the original PET image to be processed. Therefore, it is desirable that the original PET image meets a certain image quality standard such as CV < 10%. It is necessary to verify the accuracy of SUV harmonization using the proposed harmonization method by applying it to phantom data that meets the image quality standards established by JSNM.
Research on the standardization and harmonization of quantitative values for PET has been led and promoted by the Society of Nuclear Medicine/Clinical Trial Network17,18 and EANM/EARL19,20 for a long time prior to JSNM. Kaalep have reported a feasibility study on SUV harmonization in PET/CT scanner with advanced TOF and PSF technologies21, and the harmonization range of EARL's accreditation program has been updated in advance of JSNM guideline22. In the future, the harmonization filter will no longer be necessary for PET/CT scanners with these advanced technologies by the update of JSNM's harmonization range. On the other hand, PET/CT scanners without PSF or TOF technology may be excluded from quantitative multicenter studies due to their inability to adapt to the harmonization range that will be updated. In other words, it should be noted that research on SUV harmonization for multicenter PET studies will be updated as appropriate in the future.
Of the 16 PET/CT scanners registered in this study, one PET/CT scanner was excluded because the SUV calibration accuracy was not verified. Since the PET/CT scanner data was obtained retrospectively, the cause of the error that occurred when the phantom was acquired could not be clarified in this study. In addition to the possibility of a cross-calibration error, there is also the possibility of an error in the phantom data acquisition procedure. The accuracy of routine QC/QA processes and the accurate implementation of phantom data acquisition are important for the accurate achievement of harmonization in multicenter studies.
Conclusions
Quantitative harmonized multicenter studies according to the JSNM strategy are achievable by applying optimization strategy of a harmonization filter calculated semi-automatically, even in heterogeneous multicenter studies involving different generations of PET/CT scanners. When conducting harmonized multicenter studies involving quantitative evaluations of PET images, differences among scanners can be further reduced by using the SUVpeak instead of the SUVmax.
Data availability
All the analyses were performed using RC Tool for Harmonization (Nihon Medi-Physics Co.,Ltd.) and RAVAT (Nihon Medi-Physics Co.,Ltd.). Although membership registration is required, download is available at following Japanese website: https://www.nmp.co.jp/member/hiroba/index.html. Phantom data are not publicly available for download, but might be retrieved from the principal investigator Hiromitsu Daisaki.
References
Bar-Shalom, R. et al. Clinical performance of PET/CT in evaluation of cancer: additional value for diagnostic imaging and patient management. J Nucl Med. 44, 1200–1209 (2003).
Jadvar, H. et al. Appropriate use criteria for 18F-FDG PET/CT in restaging and treatment response assessment of malignant disease. J Nucl Med. 58, 2026–2037 (2017).
Na, S. J. et al. 18F-FDG PET/CT can predict survival of advanced hepatocellular carcinoma patients: a multicenter retrospective cohort study. J Nucl Med. 58, 730–736 (2017).
Lodge, M. A., Chaudhry, M. A. & Wahl, R. L. Noise considerations for PET quantification using maximum and peak standardized uptake value. J Nucl Med. 53, 1041–1047 (2012).
Vanderhoek, M., Perlman, S. B. & Jeraj, R. Impact of the definition of peak standardized uptake value on quantification of treatment response. J Nucl Med. 53, 4–11 (2012).
Kinahan, P. E. et al. The QIBA profile for FDG PET/CT as an imaging biomarker measuring response to cancer therapy. Radiology 294, 647–657 (2020).
Boellaard, R. Mutatis mutandis: harmonize the standard!. J Nucl Med. 53, 1–3 (2012).
Aide, N. et al. EANM/EARL harmonization strategies in PET quantification: from daily practice to multicentre oncological studies. Eur J Nucl Med Mol Imaging. 44(Suppl 1), 17–31 (2017).
Quak, E. et al. Does PET SUV harmonization affect PERCIST response classification?. J Nucl Med. 57, 1699–1706 (2016).
Quak, E. et al. Harmonizing FDG PET quantification while maintaining optimal lesion detection: prospective multicentre validation in 517 oncology patients. Eur J Nucl Med Mol Imaging. 42, 2072–2082 (2015).
Lasnon, C. et al. Harmonizing SUVs in multicentre trials when using different generation PET systems: prospective validation in non-small cell lung cancer patients. Eur J Nucl Med Mol Imaging. 40, 985–996 (2013).
Tsutsui Y, Daisaki H, Akamatsu G, Umeda T, Ogawa M, Kajiwara H, et al. Multicentre analysis of PET SUV using vendor-neutral software: the Japanese Harmonization Technology (J-Hart) study. EJNMMI Res. 8, 83; https://doi.org/10.1186/s13550-018-0438-9 (2018).
Japanese Society of Nuclear Medicine. Standard PET imaging protocols and phantom test procedures and criteria: executive summary. http://jsnm.sakura.ne.jp/wp_jsnm/wp-content/themes/theme_jsnm/doc/StandardPETProtocolPhantom20170201.pdf. Accessed 1 Oct 2020.
Daisaki, H. et al. Standardization of image quality across multiple centers by optimization of acquisition and reconstruction parameters with interim FDG-PET/CT for evaluating diffuse large B cell lymphoma. Ann Nucl Med. 27, 225–232 (2013).
Fukukita H, Suzuki K, Matsumoto K, Terauchi T, Daisaki H, Ikari Y, et al. Japanese guideline for the oncology FDG-PET/CT data acquisition protocol: synopsis of Version 2.0. Ann Nucl Med. 28, 693–705 (2014).
Prieto, E. et al. Impact of time-of-flight and point-spread-function in SUV quantification for oncological PET. Clin Nucl Med. 38, 103–109 (2013).
Delbeke D, Coleman RE, Guiberteau MJ, Brown ML, Royal HD, Siegel B, et al. Procedure guideline for tumor imaging with 18F-FDG PET/CT 1.0. J Nucl Med. 47, 885–895 (2006).
Sunderland, J. J. & Christian, P. E. Quantitative PET/CT scanner performance characterization based upon the society of nuclear medicine and molecular imaging clinical trials network oncology clinical simulator phantom. J Nucl Med. 56, 145–152 (2015).
Boellaard R, Delgado-Bolton R, Oyen WJ, Giammarile F, Tatsch K, Eschner W, et al. FDG PET/CT: EANM procedure guidelines for tumour imaging: version 2.0. Eur J Nucl Med Mol Imaging. 42, 328–354 (2015).
Kaalep, A. et al. EANM/EARL FDG-PET/CT accreditation - summary results from the first 200 accredited imaging systems. Eur J Nucl Med Mol Imaging. 45, 412–422 (2018).
Kaalep, A. et al. Feasibility of state of the art PET/CT systems performance harmonisation. Eur J Nucl Med Mol Imaging. 45, 1344–1361 (2018).
Kaalep A, Burggraaff CN, Pieplenbosch S, Verwer EE, Sera T, Zijlstra J, et al. Quantitative implications of the updated EARL 2019 PET-CT performance standards. EJNMMI Phys. 6, 28; https://doi.org/10.1186/s40658-019-0257-8 (2019).
Acknowledgements
We thank Mr. Tatsuya Tsuchitani, Mr. Kiyotaka Nakajima, Mr. Ryuji Ikeda, Mr. Satoshi Fujisaka, Dr. Takashi Kamiya, Mr. Shota Sakimoto and Mr. Akihiro Yamaguchi for their technical support.
Funding
This study was supported in part by grants-in-aid for scientific research from the Japan Society for the Promotion of Science (Number 19K08187). The funders had no role in the study design, data collection and analysis, decision to publish, or preparation of the manuscript.
Author information
Authors and Affiliations
Contributions
H.D., K.K. and A.T. made substantial contribution to the study design. H.D. acquired, analyzed and interpreted the data and compiled the original manuscript. The following authors provided data from the different centers, helped writing and revising the manuscript and approved the final version: K.K., M.N., T.W., K.I., F.S., T.N., M.I., A.T. All authors accepted the final version of the manuscript.
Corresponding author
Ethics declarations
Competing interests
Dr. Daisaki received research funds from Nihon Medi-Physics Co., Ltd. Dr. Nakahara received research funds from Nihon Medi-Physics Co., Ltd. and GE Healthcare Corporation. The other authors have no personal, financial, or institutional interest in any of the drugs, materials, or devices described in this article.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Daisaki, H., Kitajima, K., Nakajo, M. et al. Usefulness of semi-automatic harmonization strategy of standardized uptake values for multicenter PET studies. Sci Rep 11, 8517 (2021). https://doi.org/10.1038/s41598-021-87942-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-021-87942-0
- Springer Nature Limited
This article is cited by
-
Prognostic value of combining clinical factors, 18F-FDG PET-based intensity, volumetric features, and deep learning predictor in patients with EGFR-mutated lung adenocarcinoma undergoing targeted therapies: a cross-scanner and temporal validation study
Annals of Nuclear Medicine (2024)
-
Characterisation of a novel [18F]FDG brain PET database and combination with a second database for optimising detection of focal abnormalities, using focal cortical dysplasia as an example
EJNMMI Research (2023)
-
A review of harmonization strategies for quantitative PET
Annals of Nuclear Medicine (2023)
-
Tumor response evaluation in patients with malignant melanoma undergoing immune checkpoint inhibitor therapy and prognosis prediction using 18F-FDG PET/CT: multicenter study for comparison of EORTC, PERCIST, and imPERCIST
Japanese Journal of Radiology (2022)
-
New standards for phantom image quality and SUV harmonization range for multicenter oncology PET studies
Annals of Nuclear Medicine (2022)