Abstract
High-fidelity single-shot readout of spin qubits requires distinguishing states much faster than the T1 time of the spin state. One approach to improving readout fidelity and bandwidth (BW) is cryogenic amplification, where the signal from the qubit is amplified before noise sources are introduced and room-temperature amplifiers can operate at lower gain and higher BW. We compare the performance of two cryogenic amplification circuits: a current-biased heterojunction bipolar transistor circuit (CB-HBT), and an AC-coupled HBT circuit (AC-HBT). Both circuits are mounted on the mixing-chamber stage of a dilution refrigerator and are connected to silicon metal oxide semiconductor (Si-MOS) quantum dot devices on a printed circuit board (PCB). The power dissipated by the CB-HBT ranges from 0.1 to 1 μW whereas the power of the AC-HBT ranges from 1 to 20 μW. Referred to the input, the noise spectral density is low for both circuits, in the 15 to 30 fA/\(\sqrt{{\bf{Hz}}}\) range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μe/\(\sqrt{{\bf{Hz}}}\) and 400 μe/\(\sqrt{{\bf{Hz}}}\), respectively. For the single-shot readout performed, less than 10 μs is required for both circuits to achieve bit error rates below 10−3, which is a putative threshold for quantum error correction.
Similar content being viewed by others
Introduction
Spin qubits in semiconductors are a promising platform for building quantum computers1,2,3,4,5,6,7,8. Significant progress has been achieved in recent years, including demonstrations of extremely long coherence times9, high-fidelity state readout10,11,12,13, high-fidelity single qubits gates9,14,15,16, and two qubit gates7,16,17,18. As the field advances to multiple qubit systems, improvements in single-shot state readout and measurement times will be necessary to achieve fault tolerance. Improving the signal-to-noise ratio (SNR) and bandwidth (BW) of the qubit state detection is critical for both tunnel rate selective readout2 and energy selective readout3. With the same bit error rate, faster readout will reduce tunnel rate and metastable relaxation or relaxation related errors.
Cryogenic amplification is one way the readout SNR and BW can be improved. Challenges are that: (1) input signals remain relatively small19,20,21,22,23 and (2) significant noise and parasitic capacitance is introduced into the measurement circuit when routing the signal out of a dilution refrigerator24. Several approaches for cryogenic amplification include: radio-frequency (RF) resonant quantum point contact (QPC) and single electron transistor (SET) circuits25,26,27,28,29,30,31,32, gate dispersive RF circuits33, Josephson parametric amplification circuits34, and cryogenic transistors35,36,37,38,39. For single-shot readout, qubit state distinguishability with sensitivity 140 μe/\(\sqrt{{\rm{Hz}}}\) has been demonstrated29. However, many of these circuits require elements to be mounted at multiple fridge stages and the use of custom on-chip components, adding to the complexity of their implementation. Simpler amplification circuits that use low power transistors mounted directly on the mixing chamber stage with the qubit device thus have significant appeal38,39. For example, a proof of principle readout demonstration with a dual stage HEMT achieved Te = 240 mK, gain = 2700 A/A, power = 13 μW, noise referred to input ≤70 fA/\(\sqrt{{\rm{Hz}}}\), and 350 μe/\(\sqrt{{\rm{Hz}}}\) charge sensitivity39.
Silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) have been demonstrated to operate at liquid helium temperatures38,40 as well as millikelvin temperatures in dilution refrigerators41,42,43,44. The HBT is motivated by low 1/f noise, high Rout, and possible opportunities to achieve higher gain at the same power relative to HEMTs. Furthermore, there can be bipolar junction transistor (BJT) advantages compared to field effect transistors (FETs) for low input impedance amplifier circuits45. Our approach is to use a single SiGe HBT as a cryogenic amplifier at the mixing chamber stage of a dilution refrigerator to improve the SNR and BW of the signal from a SET used as a charge-sensor. We have designed and characterized two different HBT circuits: (1) the AC-coupled HBT circuit (AC-HBT) (Fig. 1(a)) and (2) the current-biased HBT circuit (CB-HBT) (Fig. 2(a)). The CB-HBT simply has the drain of the SET connected to the base of the HBT, while the AC-HBT has the base of the HBT connected to the drain of the SET via a resistor-capacitor (RC) bias tee. Regardless of the coupling between the HBT and SET, the HBT must be DC biased in order to amplify. For either circuit, the silicon metal oxide semiconductor (Si-MOS) device and HBT are mounted on a printed circuit board (PCB) only centimeters apart. The proximity of the HBT amplifier to the SET has the advantages of minimizing parasitic input capacitance and increasing signal before noise from the fridge is added. However, since the mixing chamber stage has a cooling power of around 100 μW at 100 mK, the HBT circuits must operate with powers similar or less in order to avoid heating.
In this letter, we first introduce the two amplification circuits with discussions of gain, sensitivity, bias behavior, and noise. We compare the basic performance and operation of the two amplifiers and extract input-referred noise as well as signal response and heating of the quantum dot electrons. Finally, we compare and discuss the performance for single-shot readout, which somewhat depends on the specific layout of the SET and quantum dot to produce larger signals via increased mutual capacitance.
AC-HBT Description
The AC-HBT consists of a Si-MOS device that is AC-coupled to an HBT (part number NESG3031M05), which amplifies the SET response to AC source-drain voltage excitation at frequencies higher than around 100 Hz. The SET is integrated into a double quantum dot (QD) device (Fig. 1(a): SEM image), which is made on a Si-MOS platform (see Section I in Supplementary Information).
To operate the AC-HBT, the DC base bias is grounded, and the emitter is biased negatively to support a base-emitter bias VBE above the cryogenic HBT threshold (about −1.04 V). The bias of the emitter power supply sets the base current, collector current, gain, and dissipated power of the HBT. The HBT current at the collector goes through a high-frequency coaxial line to a room temperature transimpedance amplifier (TIA), then through a voltage amplifier, and finally the signal is demodulated, filtered, and digitized. The TIA is referenced to ground, so the collector-emitter bias equals the base-emitter bias. We find that this configuration optimizes the circuit SNR and also requires only two lines coming from room temperature for the three HBT terminals. Figure 1(c) shows the total AC circuit gain and sensitivity vs. the amount of power dissipated by the HBT. The AC gain is measured by comparing the current of a Coulomb blockade (CB) peak with and without the HBT. The SET current can be measured directly by connecting the output of RS to a room temperature TIA (lowest ground in Fig. 1(a)). The sensitivity of the circuit is defined as the gate-voltage derivative of collector-current (slope) on the side of a CB peak, which is the typical bias point where readout occurs. Sensitivities of 1–5 μA/V are achieved in the operating region of the AC-HBT. Since the AC-HBT is a linear amplifier, the shape of a CB peak remains unaffected by different gain/sensitivity bias points of the AC-HBT (Fig. 1(d)). However, the width of the CB peak broadens at higher biases likely due to heating of the PCB by the HBT. The AC bias across the SET was chosen to be 200 μVRMS in this case to minimize the electron temperature below 200 mK.
Noise spectra are collected for different AC-HBT biases (see Section VI in Supplementary Information), and noise at around 74 kHz is referred to the HBT collector and plotted in Fig. 1(e). The noise displays two different behaviors as power dissipated is increased (Fig. 1(e)). The transconductance of the transistor \((\frac{d{I}_{C}}{d{V}_{BE}})\) increases with power, so it is important to identify where the transistor begins to add appreciable noise. In the low-power limit, the noise dependence is approximately flat at around 1 pA/\(\sqrt{{\rm{Hz}}}\), which we attribute to the noise after the HBT dominating any AC-HBT noise. As the AC-HBT power is increased to >1 μW, the noise becomes linearly dependent on power. This behavior is predicted by our estimated shot noise for the base current (Fig. 1(e) orange curve). The estimated total noise is calculated by adding all noise source predictions in quadrature (dark red curve) and aligns well with the total measured noise (blue points).
CB-HBT Description
The CB-HBT circuit consists of the same commercial HBT model wire bonded from its base terminal directly to the drain of the SET. The SET is integrated into a double QD system consisting of a lithographic QD and a secondary object that has not been definitively identified (i.e., either a QD46 or donor23). The circuit configuration for the collector and emitter terminals is similar to the AC-HBT, except for the output of the voltage amplifier, which is connected to an oscilloscope with an adjustable sample rate. In Fig. 2(b), the DC current gain and sensitivity are plotted as a function of power. The DC current gain is defined as \(\frac{{I}_{C}}{{I}_{B}}\), and the sensitivity is defined as before. The sensitivity of the CB-HBT can reach 5 μA/V between 100–500 nW, whereas the AC-HBT requires >10 μW to reach a similar sensitivity.
The CB-HBT acts as a current bias, so there is always current through the SET (see Section II in Supplementary Information). In regions of Coulomb blockade, the HBT base-emitter voltage will shift on the order of the charging energy of the SET in order to maintain a relatively constant current through the circuit. To show the current-biasing effect, a CB peak is plotted for different CB-HBT gain values in Fig. 2(d), and the current is normalized to the value at the top of the CB peak. Although the current in the blockaded regions of the CB peak is much different from a voltage-biased configuration, the slope of the sides of the CB peak appear to be less affected by the current-biasing (sensitivities of 1–5 μA/V are achieved for either circuit). We note that the effect of current bias on Coulomb blockade is independent of the HBT presence (Fig. S3 in Supplementary Information).
The noise referred to the collector of the CB-HBT is examined at around 7 kHz (Fig. 2(e)). Similar qualitatively to the AC-HBT, the lower power region is dominated by noise after the HBT around 1 pA/\(\sqrt{{\rm{Hz}}}\) (purple curve). As power is increased, the measured noise (blue points) begins to increase, which follows the estimated behavior of the base current shot-noise (orange curve) (see Section VI in Supplementary Information).
Amplifier Performance Comparison
We next compare the performance of both amplifiers with respect to power dissipated. The first metric examined is gain as power is increased. The gain of the AC-HBT is simply the measured gain of the amplifier, however the gain of the CB-HBT circuit is not as simple to extract. The small-signal resistance of the SET (rset) must be known in order to calculate the CB-HBT gain (see Section V in Supplementary Information). Since the SET is directly connected to the HBT, we cannot measure rset. Instead, we use the value of rset (3 MΩ) which best follows the measured noise behavior in Fig. 2(e) to estimate the gain. We plot this estimated gain of the CB-HBT circuit and compare to the measured gain of the AC-HBT circuit in Fig. 3(a). We observe that the CB-HBT circuit achieves higher gain at lower powers, including operating with gain over 400 at a power around 1 μW.
We next compare the noise referred to the input of the HBT for each circuit. Noise is referred to the input using the gain values in Fig. 3(a). We measure the noise spectrum for each circuit at different bias points and choose the frequency which minimizes the noise. The frequency chosen for the AC-HBT circuit was around 74 kHz, and the frequency for the CB-HBT circuit was around 7 kHz. When the input-referred noise is plotted as a function of power (Fig. 3(b)), we observe a minimum noise operating point for either circuit. At low powers, the noise is likely dominated by triboelectric noise due to the fridge and input noise of the room temperature TIA. At higher powers, the HBT amplifiers begin injecting appreciable noise into the circuit, therefore the overall noise increases. The CB-HBT circuit achieves a minimum noise of 19 fA/\(\sqrt{{\rm{Hz}}}\) at a power around 800 nW, while the AC-HBT circuit achieves a minimum noise of 26 fA/\(\sqrt{{\rm{Hz}}}\) at a power around 8.4 μW.
For the powers that minimize noise for each circuit, we plot the input-referred noise spectrum for both circuits as a function of frequency (Fig. 3(c)). The noise spectrum of the CB-HBT is plotted out to 100 kHz, since its bandwidth is less than 100 kHz. The 1/f-like behavior of the noise at lower frequencies is assumed to be due to charge noise in the Si-MOS device. In the overlapping region around 10 kHz, the noise for the CB-HBT is significantly lower than the noise for the AC-HBT.
Figure 3(d) shows the frequency dependence of an input signal for both amplification circuits up to 1 MHz. The AC-HBT has a -3 dB point at around 650 kHz, and the CB-HBT has a -3 dB point at around 20 kHz, which implies significantly lower BW than the AC-HBT. The origin of this lower BW is not well understood. Using pessimistic numbers, the frequency pole of the SET resistance (assuming 1 MΩ) and the parasitic capacitance between the SET and the base junction (assuming 1 pF) should only limit the -3 dB point to around 160 kHz. In addition, 4 K simulations of this circuit also yielded around 160 kHz -3 dB BW47 . Improvements and understanding of the BW of the CB-HBT will be important in future work.
Heating of electrons in the QD due to the operation of the connected HBT is a concern, therefore we examined the dependence of electron temperature on HBT amplifier bias (Fig. 3(e)). For the CB-HBT, we find that the minimum electron temperature observed is around 150 mK. Heating of the QD begins where the CB-HBT is operating with over 100 gain at 100 nW, therefore the CB-HBT circuit can amplify well with an electron temperature around 160–200 mK. For the AC-HBT, the minimum electron temperature was around 120 mK. When the AC-HBT bias is increased up to 3.24 μW, the electron temperature remains near the minimum temperature. For powers above this threshold, the electron temperature increases approximately linearly with power. Nonetheless, an electron temperature of 200 mK is used for the bias condition that provides the minimum amplifier noise.
Single-Shot Results Comparison
We compare both HBT amplifiers by performing single-shot readout of latched charge states10. Both Si-MOS quantum dot devices are tuned to the few electron regime and the spin filling of the last few transition lines are verified with magnetospectroscopy. Figure 4(a) shows the result of a three-level pulse sequence in the AC-HBT device where: 1) the system is initialized into (1,0), 2) ground and excited states are loaded in (2,0), and finally 3) the measurement point (signal plotted) is rastered about the (2,0)–(1,1) anti-crossing. When measuring for 30 μs, three latched lines are present, which indicates spin blockade for an excited state triplet (T), a second excited state triplet (O), and a lifting of the spin blockade for the ground state singlet (S). We assign T as a valley triplet with valley splitting of 140 μeV and the O as an orbital triplet with orbital splitting of 280 μeV. For all single-shot measurements, we remove the state O from the available state space by energy selective loading of the (2,0) state.
For both circuits, a mixture of (2,1) and (2,0) charge states are read out in the reverse latching window. Figure 4(b) shows 100 individual single-shot traces of the readout portion of the pulse for the AC-HBT device. Significant feedthrough is observed in the first few μs of the readout pulse, likely due to attenuators connecting the conductor of the high BW lines to the ground of other lines including the emitter bias line. State distinguishability does not begin to occur until about 4 μs, and then the pulse relaxes to two distinct states after about 7 μs. Extracting the SNR from these traces is done by waiting a certain amount of time, tdelay, and then averaging the signal for a certain amount of time, tintegration. Histograms of the delayed and averaged shots are compiled and fit to a double Gaussian distribution (Fig. 4(c)). The signal is defined as the separation of the center of the Gaussian peaks, and the noise is defined as the average of the standard deviations of the Gaussian peaks. The SNR is defined as the signal divided by the noise.
The extracted SNR for a given delay and total time (tdelay + tintegration) is plotted in Fig. 4(d,e). Contours are drawn for each SNR integer on both plots, where the leftmost part of a contour line reveals the minimum total measurement time required to reach a given SNR. We plot the SNR vs. minimum total measurement time in Fig. 4(f) for both circuits. The CB-HBT reaches greater SNR at any given time in the 15 μs plot range. Both circuits achieve SNR > 7 in ttotal < 10 μs, which corresponds to a bit error rate < 10−3 and marks a significant improvement over the equivalent ttotal = 65 μs in previous work10. In particular, the CB-HBT is able to reach SNR > 7 in ttotal ≈6 μs, which represents over a factor of ten improvement from the previous work10. The charge sensitivity for the CB-HBT is 330 μe/\(\sqrt{{\rm{Hz}}}\) (τint = 6 μs, SNR = 7.4), and the charge sensitivity for the AC-HBT is 400 μe/\(\sqrt{{\rm{Hz}}}\) (τint = 9 μs, SNR = 7.5). We note that the SET in the CB-HBT device had around 34% more signal due to larger mutual capacitance (Section I in Supplementary Information) which may contribute to the larger SNRs.
Conclusion
We compare the performance of two cryogenic amplification circuits: the CB-HBT and the AC-HBT. The power dissipated by the CB-HBT ranges from 0.1 to 1 μW, whereas the power of the AC-HBT ranges from 1 to 20 μW. Referred to the input, the noise spectral density is low for both circuits in the 15 to 30 fA/\(\sqrt{{\rm{Hz}}}\) range. The charge sensitivity for the CB-HBT and AC-HBT is 330 μe/\(\sqrt{{\rm{Hz}}}\) and 400 μe/\(\sqrt{{\rm{Hz}}}\), respectively. For single-shot readout performed, both circuits achieve SNR > 7 and bit error rate < 10−3 in times less than 10 μs.
The AC-HBT requires more relative overhead for implementation than the CB-HBT. The AC-HBT includes three additional surface mounted passive elements (Fig. 1(a)), which can be optimized to produce better SNR. Additionally, the AC-HBT has a two-dimensional bias space via the base bias and emitter bias, whereas the CB-HBT is only biased via the emitter bias. However, the AC-HBT is a linear gain circuit and can be used with discrete HEMTs48 and HBTs, providing more opportunity to optimize the transistor. Ideally, the transistors would have greater transconductance (gm) and a more ideal dependence on IC than the HBTs used in this work (see Section IV in Supplementary Information). In the present demonstration of the AC-HBT, heating of electrons occurred at powers which minimized noise. Introducing a second AC-HBT stage is relatively straightforward and may allow the first stage to run at powers which don’t heat the electrons and minimize the noise further. In addition, the second stage could be mounted further away from the Si-MOS PCB and reduce local heating.
Data availability
Data available upon request.
References
Kane, B. E. A silicon-based nuclear spin quantum computer. Nature 393, 133 EP (1998).
Elzerman, J. M. et al. Single-shot read-out of an individual electron spin in a quantum dot. Nature 430, 431 EP (2004).
Petta, J. R. et al. Coherent manipulation of coupled electron spins in semiconductor quantum dots. Science 309, 2180–2184 (2005).
Morello, A. et al. Single-shot readout of an electron spin in silicon. Nature 467, 687 EP (2010).
Pla, J. J. et al. High-fidelity readout and control of a nuclear spin qubit in silicon. Nature 496, 334 EP (2013).
Eng, K. et al. Isotopically enhanced triple-quantum-dot qubit. Science Advances 1, e1500214–e1500214 (2015).
Zajac, D. M. et al. Resonantly driven cnot gate for electron spins. Science eaao5965 (2017).
Rochette, S. et al. Quantum dots with split enhancement gate tunnel barrier control. Applied Physics Letters 114, 083101 (2019).
Muhonen, J. T. et al. Storing quantum information for 30 seconds in a nanoelectronic device. Nature Nanotechnology 9, 986 EP (2014).
Harvey-Collard, P. et al. High-fidelity single-shot readout for a spin qubit via an enhanced latching mechanism. Phys. Rev. X 8, 021046 (2018).
Nakajima, T. et al. Robust single-shot spin measurement with 99.5 fidelity in a quantum dot array. Phys. Rev. Lett. 119, 017701 (2017).
Shulman, M. D. et al. Suppressing qubit dephasing using real-time hamiltonian estimation. Nature Communications 5, 5156 EP (2014).
Watson, T. F., Weber, B., House, M. G., Büch, H. & Simmons, M. Y. High-fidelity rapid initialization and read-out of an electron spin via the single donor D − charge state. Phys. Rev. Lett. 115, 166806 (2015).
Takeda, K. et al. A fault-tolerant addressable spin qubit in a natural silicon quantum dot. Science Advances 2 (2016).
Kawakami, E. et al. Gate fidelity and coherence of an electron spin in an si/sige quantum dot with micromagnet. Proceedings of the National Academy of Sciences 113, 11738–11743 (2016).
Nichol, J. M. et al. High-fidelity entangling gate for double-quantum-dot spin qubits. npj Quantum Information 3, 3 (2017).
Shulman, M. D. et al. Demonstration of entanglement of electrostatically coupled singlet-triplet qubits. Science 336, 202–205 (2012).
Yoneda, J. et al. A quantum-dot spin qubit with coherence limited by charge noise and fidelity higher than 99.9%. Nature Nanotechnology 13, 102–106 (2018).
Onac, E. et al. Using a quantum dot as a high-frequency shot noise detector. Phys. Rev. Lett. 96, 176601 (2006).
Khrapai, V. S., Ludwig, S., Kotthaus, J. P., Tranitz, H. P. & Wegscheider, W. Double-dot quantum ratchet driven by an independently biased quantum point contact. Phys. Rev. Lett. 97, 176803 (2006).
Gustavsson, S. et al. Frequency-selective single-photon detection using a double quantum dot. Phys. Rev. Lett. 99, 206804 (2007).
Horibe, K., Kodera, T. & Oda, S. Back-action-induced excitation of electrons in a silicon quantum dot with a single-electron transistor charge sensor. Applied Physics Letters 106, 053119 (2015).
Harvey-Collard, P. et al. Coherent coupling between a quantum dot and a donor in silicon. Nature Communications 8, 1029 (2017).
Kalra, R. et al. Vibration-induced electrical noise in a cryogen-free dilution refrigerator: Characterization, mitigation, and impact on qubit coherence. Review of Scientific Instruments 87, 073905 (2016).
Schoelkopf, R. J., Wahlgren, P., Kozhevnikov, A. A., Delsing, P. & Prober, D. E. The radio-frequency single-electron transistor (rf-set): A fast and ultrasensitive electrometer. Science 280, 1238–1242 (1998).
Aassime, A., Johansson, G., Wendin, G., Schoelkopf, R. J. & Delsing, P. Radio-frequency single-electron transistor as readout device for qubits: Charge sensitivity and backaction. Phys. Rev. Lett. 86, 3376–3379 (2001).
Reilly, D. J., Marcus, C. M., Hanson, M. P. & Gossard, A. C. Fast single-charge sensing with a rf quantum point contact. Applied Physics Letters 91, 162101 (2007).
Barthel, C., Reilly, D. J., Marcus, C. M., Hanson, M. P. & Gossard, A. C. Rapid single-shot measurement of a singlet-triplet qubit. Phys. Rev. Lett. 103, 160503 (2009).
Barthel, C. et al. Fast sensing of double-dot charge arrangement and spin state with a radio-frequency sensor quantum dot. Physical Review B 81 (2010).
Mason, J. et al. A high speed radio-frequency quantum point contact charge detector for time resolved readout applications of spin qubits. Physica E: Low-dimensional Systems and Nanostructures 42 (2010).
Yuan, M. et al. Charge sensing in a si/sige quantum dot with a radio frequency superconducting single-electron transistor. Applied Physics Letters 101, 142103 (2012).
Verduijn, J., Vinet, M. & Rogge, S. Radio-frequency dispersive detection of donor atoms in a field-effect transistor. Applied Physics Letters 104, 102107 (2014).
Colless, J. I. et al. Dispersive readout of a few-electron double quantum dot with fast rf gate sensors. Physical Review Letters 110 (2013).
Stehlik, J. et al. Fast charge sensing of a cavity-coupled double quantum dot using a josephson parametric amplifier. Phys. Rev. Applied 4, 014018 (2015).
Visscher, E. H. et al. Broadband single-electron tunneling transistor. Applied Physics Letters 68, 2014–2016 (1996).
Pettersson, J. et al. Extending the high-frequency limit of a single-electron transistor by on-chip impedance transformation. Phys. Rev. B 53, R13272–R13274 (1996).
Vink, I. T., Nooitgedagt, T., Schouten, R. N., Vandersypen, L. M. K. & Wegscheider, W. Cryogenic amplifier for fast real-time detection of single-electron tunneling. Applied Physics Letters 91, 123512 (2007).
Curry, M. J. et al. Cryogenic preamplification of a single-electron-transistor using a silicon-germanium heterojunction-bipolar-transistor. Applied Physics Letters 106, 203505 (2015).
Tracy, L. A. et al. Single shot spin readout using a cryogenic high-electron-mobility transistor amplifier at sub-kelvin temperatures. Applied Physics Letters 108, 063101 (2016).
Joseph, A. J., Cressler, J. D. & Richey, D. M. Operation of sige heterojunction bipolar transistors in the liquid-helium temperature regime. IEEE Electron Device Letters 16, 268–270 (1995).
Najafizadeh, L. et al. Sub-1-k operation of sige transistors and circuits. IEEE Electron Device Letters 30, 508–510 (2009).
Curry, M. et al. Single-shot charge readout using a cryogenic heterojunction bipolar transistor preamplifier inline with a silicon single electron transistor at millikelvin temperatures. Bulletin of the American Physical Society 61 (2016).
Ying, H. et al. Operation of sige hbts down to 70 mk. IEEE Electron Device Letters 38, 12–15 (2017).
Davidović, D. et al. Tunneling, current gain, and transconductance in silicon-germanium heterojunction bipolar transistors operating at millikelvin temperatures. Phys. Rev. Applied 8, 024015 (2017).
Horowitz, P., Hill, W. & Robinson, I. The Art of Electronics, vol. 2 (Cambridge University Press Cambridge, 1980).
Jock, R. M. et al. A silicon metal-oxide-semiconductor electron spin-orbit qubit. Nature Communications 9, 1768 (2018).
England, T. et al. Comparing sige hbt amplifier circuits for fast single-shot spin readout. Bulletin of the American Physical Society 62 (2017).
Tracy, L., Reno, J. & Hargett, T. On-chip hemt amplifiers for semiconductor spin qubit readout. Bulletin of the American Physical Society (2018).
Acknowledgements
This work was performed, in part, at the Center for Integrated Nanotechnologies, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International, Inc., for the DOE’ s National Nuclear Security Administration under contract DE-NA0003525. This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
Author information
Authors and Affiliations
Contributions
M.J.C., M.R., T.D.E., and S.M.C. designed the amplification circuits. J.M.A., D.M.C., J.R.W., and D.R.W. fabricated the Si-MOS devices. M.J.C., M.R., T.D.E, A.M.M., R.M.J., C.B.-O., P.H.-C., P.A.S., and M.P.L. characterized the amplification circuits with Si-MOS devices. M.J.C. and T.D.E. modeled the amplification circuits. M.J.C., M.R., and M.S.C. wrote the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Curry, M.J., Rudolph, M., England, T.D. et al. Single-Shot Readout Performance of Two Heterojunction-Bipolar-Transistor Amplification Circuits at Millikelvin Temperatures. Sci Rep 9, 16976 (2019). https://doi.org/10.1038/s41598-019-52868-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-52868-1
- Springer Nature Limited
This article is cited by
-
The SpinBus architecture for scaling spin qubits with electron shuttling
Nature Communications (2024)
-
A silicon singlet–triplet qubit driven by spin-valley coupling
Nature Communications (2022)
-
Scaling silicon-based quantum computing using CMOS technology
Nature Electronics (2021)
-
Cryogenic amplification of image-charge detection for readout of quantum states of electrons on liquid helium
Journal of Low Temperature Physics (2021)