Abstract
Upon illumination, a dielectric microsphere (μS) can generate a photonic nanojet (PNJ), which plays a role in the super-resolution imaging of a sample placed in the μS’s immediate proximity. Recent microscopy implementations pioneered this concept but, despite the experimental characterization and theoretical modeling of the PNJ, the key physical factors that enable optimization of such imaging systems are still debated. Here, we systematically analyzed the parameters that govern the resolution increase in the case of large-diameter (>20 µm) μS-assisted incoherent microscopy by studying both the illumination and the detection light paths. We determined the enhanced-resolution zone created by the μS, in which the detection system has a net resolution gain that we calculated theoretically and subsequently confirmed experimentally. Our results quantitatively describe the resolution enhancement mediated by the optical contrast between the μS and its surrounding medium, and provide concrete means for designing μS-enhanced imaging systems for several application requirements.
Similar content being viewed by others
Introduction
Photonic nanojets (PNJs) emerging from the shadow side of a dielectric micro-objects were studied intensively in recent years1,2,3,4,5,6, and have been employed in newly developed super-resolution microscopy techniques7,8,9. Because the PNJ was considered the main reason of the resolution increase in µS-assisted super-resolution microscopy, extensive characterization of this illumination mode was achieved by the microscopy community10,11,12,13,14,15,16,17,18,19,20. A variety of applications have been proposed for μS-assisted microscopy, from micro-topography measurement21,22 to live-cell imaging23,24,25, with implementations employing large μSs (>20 μm), because they provide an increased field-of-view and are easier to handle26,27,28,29. More recently, however, it has been proposed to revise and standardize the resolution claimed in μS-assisted microscopy and was demonstrated that the experimentally observed resolution gains could not be explained solely by the creation of the PNJ30. Indeed, while small sample-μS distances (<1 μm) are required for super-resolution imaging31,32,33, multiple numerical simulations showed that, in such configurations, the focus of the light is projected to several tens of micrometers away from the shadow-side of the microsphere34,35,36. Moreover, for such small sample-μS distance, objects of different nature may constrain the imaging conditions (e.g. use of a specific immersion medium for live-cell imaging). Previous studies on large μSs reported the assessment of the effective field-of-view and magnification created by the μS37,38, or the effect of embedding in an elastomer39. However, as those analyses mainly focused on the PNJ illumination, no exact prediction about the gain in spatial resolution was reported. Therefore, to establish the best imaging conditions for incoherent microscopy where large diameter (>20 µm) µSs are employed, we (i) explored both the illumination and the detection path through the μS to derive the theoretical resolution gain for different immersion configurations, (ii) validated the results experimentally, and (iii) provided parameters for imaging system optimization based on quantitative predictions.
Results
Analysis of the illumination path
To explore the contribution of the focused light in the illumination path, we studied its dependence on the optical contrast between the μS and the immersion medium. We used the finite element method (FEM) to calculate the electric field generated by a 40 μm diameter barium titanate glass (BTG) μS in either oil- or water-immersion medium upon illumination from the top (as detailed in the Methods section), and derived the light intensity values by multiplying the calculated electric field with its complex conjugate (Fig. 1a). Both systems project the focused light ~20 µm from the shadow-side of the µS but, since during imaging the sample must be in the vicinity of the µS, we investigated the intensity profiles within 1 μm from the μS, and found that in this position, they do not markedly differ in the two situations (Fig. 1b). Analysis of different μS materials and sizes in the most common immersion media (Figs 1, S1 and S2) shows that, as long as the optical contrast allows the formation of the PNJ, the intensity profiles close to the μS are very similar. This indicates that the PNJ illumination in the imaging region is very robust with respect to the optical contrast and will play a minor role in eventual resolution changes that would appear when varying this parameter.
Analysis of the detection path
To analyze the detection path from the sample to the microscope objective, we used an analytical approach based on Fourier optics and ray tracing. Propagation of monochromatic light in homogenous media can be described by the Helmholtz equation40:
where ψ(r) is the spatial part of the propagating field, \(k=\frac{2\pi n}{\lambda }\) is its wave-number, with λ being its wavelength and n the refractive index of the medium. The general solution of Equation (1) in linear coordinates can be written as
where kx, ky and kz are the component of the wave-vector \({\boldsymbol{(}}k={k}_{x}{\bf{x}}+{k}_{y}{\bf{y}}+{k}_{z}{\bf{z}})\), and \({\hat{\psi }}_{0}({k}_{x},{k}_{y})={\int }_{-\infty }^{+\infty }{\int }_{-\infty }^{+\infty }\)\({\psi }_{0}(x,y){e}^{-i({k}_{x}x+{k}_{y}y)}dxdy\) is the Fourier transform of the field at z = 0 (i.e. the object-plane). \({\hat{\psi }}_{0}({k}_{x},{k}_{y})\) contains the spatial information about the object and is usually called angular spectrum40. With this approach, the spatial field solution can be interpreted as the sum of its plane wave components \({e}^{i({k}_{x}x+{k}_{y}y+{k}_{z}z)}\), which are the eigenfunctions of the Helmholtz operator. Each of these plane waves carries some information about the spatial distribution of the object in the term \({\hat{\psi }}_{0}({k}_{x},{k}_{y})\) and propagates at an angle θ with respect to the z-axis. This angle is given by the standard definition of the wave vector components in spherical coordinates:
where θ and φ are the polar and the azimuthal angle. The number of plane waves collected by the optical system determines the amount of spatial information retrieved about the original object, which explains why the maximum θobj that can be collected by an objective (i.e. half of the acceptance angle) limits the spatial resolution of the optical system in accordance with the standard definition of Abbe’s resolution:
where \({{\rm{NA}}}_{{\rm{obj}}}=n\,\sin \,{\theta }_{{\rm{obj}}}\) is the numerical aperture of the objective. Methods to artificially increase the angular spectrum collected by the detection system are used in techniques such as I5 M29 and SIM30.
Following this approach, we modelled the propagation of each individual wave originating from a point sample for a μS much larger than λ (Fig. 2a). Each wave propagates away from the sample at a certain angle with respect to the sample-μS axis, then it enters the μS by refraction, propagates inside the μS and exits again by refraction. In this procedure, the μS can be interpreted as a non-linear operator that transforms an input angle θin into an output angle θout, both measured with respect to the optical axis. This operator depends on four parameters: the distance h between the sample and the μS; the diameter d of the μS; the refractive indices of the μS (ns) and of the surrounding medium (nm). By applying Snell’s law to the refraction points for each ray, and linear propagation otherwise, we calculated the functional relation between θin and θout for a BTG μS (d = 40 µm, ns = 1.95) immersed in oil (nm = 1.56) or in water (nm = 1.33), for sample-μS distances ranging from 0.1 to 10 µm (Fig. 2b,c). The method for this calculation is detailed in the Methods section. The relation between θin and θout is very different for oil and water immersion. However, both situations lead to a decrease of θout compared to the absence of the μS. Parallel, the objective acceptance angles for an oil-immersion objective with NA = 1.4 and a water-immersion objective with NA = 0.75 are shown. The larger angles that are guided back to the objective by the μS generate an enhanced-resolution zone (ERZ) in which the amount of collected angular spectrum is increased. This translates into a net increase of the NA of the system (Fig. 2d), which results in a net gain for the lateral resolution as derived from equation (4):
where θμS is the maximum θin refracted by the μS that stays within the acceptance cone of the objective. For the axial resolution, which scales as NA−2, the gain is even higher and corresponds to G2. In Fig. 2e we show both lateral and axial resolution gains for the oil- and water-immersion objectives considered in Fig. 2b,c. We find that the resolution gain is markedly different when using a μS in either water or oil medium, and that much more gain is expected theoretically when using the μS in water. Moreover, as the gain is uniform in this region, no very precise location of the sample is needed to get the same resolution enhancement. This guarantees the imaging robustness which is very useful in optical system design.
To verify the theoretical predictions, we compared the measured and calculated spatial frequency coverage by imaging line-space micro-patterns (LSMPs), which was shown as a suitable characterization method of optical systems for both coherent41 and incoherent42 imaging. The spatial frequencies present in the object are partially filtered by the optical system, so that the contrast between the features in the object is attenuated in the image. In incoherent imaging, the intensity modulation in the object is transferred to an intensity modulation in the image by the modulation transfer function (MTF) of the optical system, which is given by the modulus of the Fourier transform of the point spread function (PSF)40. In the case of microscope objectives, for which the PSF is the well-known Airy disk, the MTF is
where \(f=\arccos (\frac{\lambda }{2{\rm{NA}}}u)\) is the normalized spatial frequency, u being the linear spatial frequency. In Fig. 3a, we calculated the MTF for the two objectives considered in Fig. 2, in the presence and absence of a μS. The range of λ considered for this calculation was 545 ± 20 nm, corresponding to the experimental band-pass filter placed behind the light source. Similarly, the NA considered in the presence of the μS was the one obtained for short sample-μS distance (i.e. for the sample laying within the imaging region). The maximum spatial frequency that is predicted to be resolved by the objective (i.e. MTF(u) > 0) is increased in the presence of the μS for both oil- and water-immersion. However, the water-immersion objective is expected to gain more than the oil-immersion objective. To illustrate the modulation enhancement below the diffraction limit of the optical system (λ/2NA = 545 nm/2*0.75 = 363 nm), we show an LSMP of 360 nm-pitch in the absence and presence of the μS in Fig. 3b and their intensity profiles in Fig. 3c, which shows that the LSMP peaks becomes resolvable when imaged through the water-immersed μS. The predictions were confirmed by the measurements on several LSMPs (Fig. 3d,e), where the expected behavior of the objective alone was confirmed and the predicted spatial frequency coverage in the presence of the μS followed the predictions perfectly. The Abbe resolution limit corresponds to the point at which the MTF crosses the horizontal axis, and we also report the noise level of the optical system (dotted lines in Fig. 3d,e) as a reference, which further confirms that the null modulation predicted below the diffraction limit without the μS (light-blue line) lies indeed within the noise region (light-blue squares) as expected. We report the image of a single line in Fig. S3 to elucidate the difference between the resolution of the optical system and its minimal detectable feature.
Discussion
This systematic characterization of the resolution gain mediated by the μS enables to explore the properties of the resulting imaging system in a detailed manner, and optimization of the imaging conditions can then be assessed with the described model. For instance, it can be used to predict the resolution gain for configurations with various immersion media, μS materials and sizes. We demonstrate the potential of the quantitative predictions of the model in Fig. 4. We calculated the relation between the input and the output angle for the most common immersion media (Fig. 4a). In order not to lose generality, we did not consider the optical glue and the supporting glass for these calculations, because they can be different in other implementations of the technique12,15,26,33,34,35. On the same graph, we report the output \({{\rm{NA}}}_{{\rm{out}}}={n}_{{\rm{m}}}{\theta }_{\mathrm{out},\max }\) for each condition, where θout,max is the maximum output angle (i.e. the minimum acceptance angle needed for the objective to collect the entire spatial information). The lower NAout, the larger the resolution gain that can be obtained. From air (lowest refractive index) to oil (highest refractive index) the behavior changes in a non-monotonic way, since increasing nm does not always result in lowering NAout. This demonstrates that the optimal resolution gain has a non-trivial dependence on the contrast between the refractive indices of the medium and the μS. To study this effect, we calculated θout,max as a function of nm in the range 1–1.6 (Fig. 4b). A minimum is clearly visible for θout,max, at which the resolution gain reaches a maximum. Finally, we studied this behavior for two common glass types for a large range of μS (20–200 μm) and showed a representative subset of θout,max (lines) and resolution gains (stars) in Fig. 4c. We observe that the position of the maximum resolution gain shifts mainly when changing the μS material (>10%), and only slightly when varying the μS size in the μm range (<10%). This calculations of the resolution enhancement provide a quantitative design tool for optimization of μS-assisted imaging systems: for instance, when the sample requires no immersion, soda-lime glass (SLG) μSs give a higher gain; conversely, when studying living cells in water-based media, BTG μSs are more suitable.
In conclusion, these results quantitatively describe the resolution gain mediated by the μS as a function of the physical parameters of the optical system, and provide predictions for several configurations of μS materials and immersion media, offering a method to optimize microscopy configuration for different application requirements based on μS-assisted imaging.
Methods
Calculations for comparing the photonic nanojet in water- and oil-immersion systems
To analyze the PNJs created by the water- and the oil-immersion system, finite element method (FEM) simulations were carried out in COMSOL Multiphysics software. Propagation of 545 nm light (corresponding to the illumination setup) was modelled based on the configuration of the chip used for the experiments. The chip consisted of a D263 glass substrate (nD263 = 1.525) on which a BTG µS (nBTG = 1.950) was placed between the SU8 (nSU8 = 1.575) sidewalls. The cavities between the µS and the D263 were filled with NOA63 optical glue (nNOA63 = 1.560). The modelling of the surrounding of the microsphere was necessary in order to establish the same illumination conditions as in our experimental setup. However, the same results can be obtained if the SU8 and the D263 glass are not considered, as the former is not involved in the investigated light path, while border of the latter is reached by the light perpendicularly (i.e. Snell’s law ensures that in this case the light can travel forward without refraction). On the other hand the optical glue may play a minor role, as its refractive index deviates from the one of the D263 glass’ by less than 0.04. In order to obtain a precise solution, we did not neglect this difference. The immersion medium was a changing parameter (nair = 1.000, nwater = 1.333, nSiOil = 1.400, nglycerol = 1.470, and noil = 1.560). The following scalar equation was used to study transverse electric waves in this two dimensional model:
where k0 is the free-space wave number, εr = (n-ik)2 is the relative permittivity, expressed with the refractive index n and its imaginary part k. In this model, the scattering boundary condition was used at all exterior boundaries, and the continuity boundary condition was used at all material interfaces. During meshing, the minimum element size was 10 nm, while the maximum element size of λ/4 was set to obtain a precise solution. After the model was solved, the normalized electric field was multiplied by its conjugate and the logarithmic of the intensity values were plotted (Figs. 1, S1 and S2).
Analytical calculation of the light path through the microsphere
To quantitatively calculate the effect of the μS on the light cone rising from the sample, we used the property of cylindrical symmetry to reduce the calculation to a 1D problem (Fig. 5). Each ray rising from the sample can be fully described by its starting polar angle θin with respect to the sample-μS axis. With the notation used in Fig. 5, Snell’s law at the refraction points P1 and P2 imply
Moreover, trigonometric properties imply
Finally, simple geometry gives
Equations (7–9) were used to calculate θout in the range of \({\theta }_{in}\in [0;\,\arcsin \frac{r}{r+h}]\), which corresponds to the angles that intercept the μS. In cases where the optical glue and the glass coverslip were taken into account, Snell’s law and simple geometry gives
Where θout′ is the final output angle.
Image acquisition
To perform the experimental control for the theoretical MTF, a custom imaging setup was built. First, a chip with fixed BTG microspheres was created. A D 263 M borosilicate glass (Menzel-Gläser, Germany) substrate of 22 × 22 × 0.15 mm3 was cleaned with oxygen plasma which was followed by 20 µm 3025 type SU8 (MicroChem, USA) coating. Then, 40 µm diameter wells were patterned into the SU8 layer with photolithography. After development, a 4 µl droplet of Norland Optical Adhesive 63 (NOA63, Norland Products, USA) was spread on the top of the chip. This was followed by a 20 minutes vacuum treatment to remove the air bubbles stuck in the wells of the SU8 layer. Subsequently, 38–45 µm diameter BTG (Cospheric, USA) microspheres were placed on the NOA63 layer. The microspheres were swiped over the surface multiple times until they got located in the wells. The excess amount of microspheres was removed to prevent them acting as a spacer during imaging. Finally, the chip was exposed to UV light until an accumulated dose of 4.5 Joules/cm2 was reached, which is required for curing the NOA63 optical glue. For the experiments, this chip was placed upside down onto the sample, i.e. the BTG microspheres came into close contact with the sample. The imaged sample was a silicon-based microscope calibration target (MetroBoost, USA), which contained line-space micro-patterns (SiO2 – PolySi, respectively) with various pitch between 240–500 nm. The sample with the chip on top was imaged with an Axio Imager M2m upright optical microscope, equipped with HAL100 halogen light source (Zeiss, Germany). A filter cube with a band-pass (524–565 nm) excitation filter and an 80T-20R beam splitter (both from AHF, Germany) was placed in the optical path. For the oil-immersion experiments, a 63x, Na = 1.4 objective (Zeiss, Germany) was used. The images were captured with an AxioCam MRm (Zeiss, Germany) that had 6.45 µm × 6.45 µm pixel size. This resulted in mapping 102 nm of the sample into 1 pixel. For the water-immersion experiments, a 40×, NA = 0.75 objective (Zeiss, Germany) was used in combination with a DMK31BF03.H (TIS, Germany) camera that had 4.65 µm × 4.65 µm pixel size, which resulted in mapping 116 nm to 1 pixel. Note that, when present, the BTG microsphere introduces an extra ~2× magnification to the system.
Quantification of the experimental MTF
After acquisition, the images were stored as 8 bit grayscale pictures. To determine the modulation of the recorded signal, the average intensity values along a 5 pixel-wide line (crossing the line-space micro-patterns) were extracted (Fig. 4b,c). The structure of 8 bit grayscale picture is constructed in a way that the value 255 belongs to a fully white pixel, meanwhile 0 marks a totally black one. Because of the material properties of the imaged sample, the background looked bright on the images and the lines were seen as dark lines. Corresponding to that, when plotting the intensity profile, the signal looked like a step from higher value to lower ones, then the modulation could have been seen and then a step back to the starting level (Fig. 4c). The modulated region was analysed by detecting peaks and valleys and calculating all amplitudes (a) from these values. Because of the structure of the sample, this meant 9–11 values (one per line), from which we calculated a′ = median(a) and a′error = MAD(a), where a is the vector of the amplitude values. Then the step (s) was measured. Subsequently, the modulation (M) was calculated as:
To guarantee the same normalization of the modulation values as the theoretical MTF, which is always normalized at unity at zero spatial frequency, another area of the sample was imaged, where the same two materials had a common border but without any modulation pattern (i.e. with a null spatial frequency = 0). This showed how the imaging system could map the maximum observable modulation (M0). From this measurement, M0 was calculated as:
where step was the average grey value over 10 pixel in the SiO2 (to measure maximum dark value) and baseline was the same in PolySi (to measure maximum bright value). The final normalized modulation (M′) that is shown in Fig. 4d,e was derived as M′ = M/M0.
The noise level modulation was calculated by applying the same methodology in 24 uniform regions (i.e. without the presence of any microstructured edge) for each immersion type, then averaged and normalized.
References
Chen, Z., Taflove, A. & Backman, V. Photonic nanojet enhancement of backscattering of light by nanoparticles: a potential novel visible-light ultramicroscopy technique. Opt. Express 12, 1214–1220 (2004).
Lecler, S., Takakura, Y. & Meyrueis, P. Properties of a three-dimensional photonic jet. Opt. Lett. 30, 2641–2643 (2005).
Aouani, H., Djaker, N., Wenger, J. & Rigneault, H. High-efficiency single molecule fluorescence detection and correlation spectroscopy with dielectric microspheres. In (eds Enderlein, J., Gryczynski, Z. K. & Erdmann, R.) 75710A-75710A–12, https://doi.org/10.1117/12.840041 (2010).
Yan, Y. et al. Microsphere-Coupled Scanning Laser Confocal Nanoscope for Sub-Diffraction-Limited Imaging at 25 nm Lateral Resolution in the Visible Spectrum. ACS Nano 8, 1809–1816 (2014).
Ghenuche, P., de Torres, J., Ferrand, P. & Wenger, J. Multi-focus parallel detection of fluorescent molecules at picomolar concentration with photonic nanojets arrays. Appl. Phys. Lett. 105, 131102 (2014).
Astratov, V. N. et al. Fundamental limits of super-resolution microscopy by dielectric microspheres and microfibers. in 97210K, https://doi.org/10.1117/12.2212762 (2016).
Huszka, G. & Gijs, M. A. M. Turning a normal microscope into a super-resolution instrument using a scanning microlens array. Sci. Rep. 8 (2018).
Li, Y., Shi, Z., Shuai, S. & Wang, L. Widefield scanning imaging with optical super-resolution. J. Mod. Opt. 62, 1193–1197 (2015).
Krivitsky, L. A., Wang, J. J., Wang, Z. & Luk’yanchuk, B. Locomotion of microspheres for super-resolution imaging. Sci. Rep. 3 (2013).
Chen, Z., Taflove, A., Li, X. & Backman, V. Superenhanced backscattering of light by nanoparticles. Opt. Lett. 31, 196–198 (2006).
Heifetz, A. et al. Experimental confirmation of backscattering enhancement induced by a photonic jet. Appl. Phys. Lett. 89, 221118 (2006).
Heifetz, A., Kong, S.-C., Sahakian, A. V., Taflove, A. & Backman, V. Photonic Nanojets. J. Comput. Theor. Nanosci. 6, 1979–1992 (2009).
Geints, Y. E., Panina, E. K. & Zemlyanov, A. A. Control over parameters of photonic nanojets of dielectric microspheres. Opt. Commun. 283, 4775–4781 (2010).
Grojo, D. et al. Bessel-like photonic nanojets from core-shell sub-wavelength spheres. Opt. Lett. 39, 3989 (2014).
Jalali, T. & Erni, D. Highly confined photonic nanojet from elliptical particles. J. Mod. Opt. 61, 1069–1076 (2014).
Shen, Y., Wang, L. V. & Shen, J.-T. Ultralong photonic nanojet formed by a two-layer dielectric microsphere. Opt. Lett. 39, 4120 (2014).
Gu, G. et al. Super-long photonic nanojet generated from liquid-filled hollow microcylinder. Opt. Lett. 40, 625 (2015).
Yang, H., Trouillon, R., Huszka, G. & Gijs, M. A. M. Super-resolution imaging of a dielectric microsphere is governed by the waist of its photonic nanojet. Nano Lett. 4862–4870, https://doi.org/10.1021/acs.nanolett.6b01255 (2016).
Darafsheh, A. Influence of the background medium on imaging performance of microsphere-assisted super-resolution microscopy. Opt. Lett. 42, 735 (2017).
Upputuri, P. K. & Pramanik, M. Microsphere-aided optical microscopy and its applications for super-resolution imaging. Opt. Commun. 404, 32–41 (2017).
Yan, B. et al. Superlensing microscope objective lens. Appl. Opt. 56, 3142 (2017).
Duocastella, M. et al. Combination of scanning probe technology with photonic nanojets. Sci. Rep. 7 (2017).
Yang, H., Moullan, N., Auwerx, J. & Gijs, M. A. M. Fluorescence Imaging: Super-Resolution Biological Microscopy Using Virtual Imaging by a Microsphere Nanoscope (Small 9/2014). Small 10, 1876–1876 (2014).
Wang, F. et al. Scanning superlens microscopy for non-invasive large field-of-view visible light nanoscale imaging. Nat. Commun. 7, 13748 (2016).
Li, J. et al. Swimming Microrobot Optical Nanoscopy. Nano Lett. 16, 6604–6609 (2016).
Li, L., Guo, W., Yan, Y., Lee, S. & Wang, T. Label-free super-resolution imaging of adenoviruses by submerged microsphere optical nanoscopy. Light Sci. Appl. 2, e104 (2013).
Lee, S., Li, L., Ben-Aryeh, Y., Wang, Z. & Guo, W. Overcoming the diffraction limit induced by microsphere optical nanoscopy. J. Opt. 15, 125710 (2013).
Allen, K. W. et al. Super-resolution microscopy by movable thin-films with embedded microspheres: Resolution analysis. Ann. Phys. 527, 513–522 (2015).
Du, B., Ye, Y. -H., Hou, J., Guo, M. & Wang, T. Sub-wavelength image stitching with removable microsphere-embedded thin film. Appl. Phys. A 122 (2016).
Luk’yanchuk, B. S., Paniagua-Domínguez, R., Minin, I., Minin, O. & Wang, Z. Refractive index less than two: photonic nanojets yesterday, today and tomorrow [Invited]. Opt. Mater. Express 7, 1820 (2017).
Huszka, G., Yang, H. & Gijs, M. A. M. Microsphere-based super-resolution scanning optical microscope. Opt. Express 25, 15079 (2017).
Wang, Z. et al. Optical Virtual Imaging at 50 Nm Lateral Resolution with a White-Light Nanoscope. Nat. Commun. 2, 218 (2011).
Sundaram, V. M. & Wen, S.-B. Analysis of deep sub-micron resolution in microsphere based imaging. Appl. Phys. Lett. 105, 204102 (2014).
Yang, H. & Gijs, M. A. M. Optical microscopy using a glass microsphere for metrology of sub-wavelength nanostructures. Microelectron. Eng. 143, 86–90 (2015).
Lai, H. S. S. et al. Super-Resolution Real Imaging in Microsphere-Assisted Microscopy. PLOS ONE 11, e0165194 (2016).
Wang, F. et al. Three-Dimensional Super-Resolution Morphology by Near-Field Assisted White-Light Interferometry. Sci. Rep. 6, 24703 (2016).
Darafsheh, A., Walsh, G. F., Dal Negro, L. & Astratov, V. N. Optical super-resolution by high-index liquid-immersed microspheres. Appl. Phys. Lett. 101, 141128 (2012).
Lee, S. et al. Immersed transparent microsphere magnifying sub-diffraction-limited objects. Appl. Opt. 52, 7265 (2013).
Darafsheh, A., Guardiola, C., Palovcak, A., Finlay, J. C. & Cárabe, A. Optical super-resolution imaging by high-index microspheres embedded in elastomers. Opt. Lett. 40, 5 (2015).
Goodman, J. W. Introduction to Fourier Optics. (Roberts and Company Publishers, 2005).
Horstmeyer, R., Heintzmann, R., Popescu, G., Waller, L. & Yang, C. Standardizing the resolution claims for coherent microscopy. Nat. Photonics 10, 68–71 (2016).
Sitter, D. N., Goddard, J. S. & Ferrell, R. K. Method for the measurement of the modulation transfer function of sampled imaging systems from bar-target patterns. Appl. Opt. 34, 746–751 (1995).
Acknowledgements
The authors would like to thank for Swiss National Science Foundation Grant (200021-152948) for founding this project.
Author information
Authors and Affiliations
Contributions
D.M. generated the analytical model to calculate the resolution gain, the method for the quantification of the experimental MTF, and the predictions on the different imaging configurations. G.H. generated the data of the experimental MTF, and the data of the simulated PNJ. D.M. and G.H. analysed the data. D.M., G.H. and M.A.M.G. wrote the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Migliozzi, D., Gijs, M.A.M. & Huszka, G. Microsphere-mediated optical contrast tuning for designing imaging systems with adjustable resolution gain. Sci Rep 8, 15211 (2018). https://doi.org/10.1038/s41598-018-33604-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-33604-7
- Springer Nature Limited