Abstract
Layer-by-Layer (LbL) self-assembly has been investigated for several decades. However, the conventional LbL method has performance problems on the chair-side caused by its cumbersome and time-consuming process. Thus, we investigate a new LbL self-assembly technique for the fast and high efficient preparation process based on the brush. The multilayer films fabricated by simple sequential brushing of polyelectrolyte solutions are compared to the classical dipping method. We characterize the multilayer films by characteristics such as their morphology and thickness, and compare them against those of the classic method by profilometry, atomic force microscopy. We prepare multilayer films with biocompatible polyelectrolytes, chitosan, and alginate incorporated with a hydrophobic drug carrier. For the drug carrier, a poly(ethylene glycol)-block-poly(ε-caprolactone) (PEG-b-PCL) block copolymer is introduced to construct micelles containing dexamethasone, which is a well-known osteogenesis-inducing drug. The hydrogen bonding behavior between adjacent layers and micelles is investigated by Fourier transform infrared spectroscopy. Additionally, we analyze the release profiles, degradation profiles and toxicity of the multilayer films for biomedical applications. From these results, we can identify the brushing LbL method as a reliable and more efficient multilayer film-construction process compared to conventional dipping LbL, especially for practical applications in dental and clinical situations.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
Amphiphilic block copolymers, which have hydrophobic and hydrophilic segments with different solubilities in their structure, have been widely studied for their ability to self-assemble into polymeric micellar structures in selective solutions. Amphiphilic block copolymer micelles can be formed with well-defined nano-sized core-shell structures that possess excellent solubilities in selective solutions, high stabilities, and extended blood circulation periods1,2,3,4. Contributing to biocompatibility and reduced thrombogenicity of PEG resulting from a brisk chain motion that reduces the interfacial free energy to a low level, poly(ethylene glycol)-block-poly(ε-caprolactone) (PEG-b-PCL) has attracted enormous attention as a hydrophobic drug carrier over the past few decades1,5,6,7,8,9,10. PCL also has biocompatible and biodegradable properties11, so has been studied as the hydrophobic core of polymeric micellar structures for the loading of hydrophobic drugs. However, there are still drawbacks to utilizing block copolymer micelles as a hydrophobic drug delivery platform, such as the difficult quantitative control and undefined release profile when used alone. Therefore, there have been attempts to incorporate block copolymer micelles into a film structure, especially nanoscale multilayer thin films, for controlling the loading amount and release profiles of small molecules or some hydrophobic anticancer drugs12,13,14.
On the other hand, the layer-by-layer (LbL) self-assembly technique has been widely studied; it has become a prevalent coating method for biomedical applications in the past few decades until recently because of its simplicity and versatility to form nanoscale structures15,16,17,18,19,20,21. LbL self-assembly is a fabrication technique based on the sequential adsorption of materials, especially polyelectrolytes or polypeptides, with mutual interactions with counter materials by electrostatic interactions, hydrogen bonding, hydrophobic interactions, or covalent bonding12,22, Also, as the major driving forces of LbL self-assembly are founded on intermolecular interactions, it is a very powerful method for adjusting the characteristics of nano-sized structure of the thin films, such as porosity, thickness, roughness, and density, in the desired way by simply controlling the fabrication conditions including pH, salt concentration, or the number of bilayers23. Based on this unique advantages, there have been many attempts to incorporate polymeric nano particles or micelles into multilayer films fabricated by LbL assembly for hydrophobic drug delivery systems. Additionally unlimited kinds of materials can be used in film formation. Owing to these many advantages in film construction, LbL-assembled films have been widely investigated for drug delivery systems and biomedical purposes.
With LbL assembly, there are many different routes to fabricate thin films depending on their purpose, including immersive, spraying, spin coating, and electromagnetic methods, accomplished in preceding research24. Among these various techniques, immersion is the dominantly studied technology, also referred to as dipping assembly because its mechanism completely depends on thermodynamics. This means a high reproducibility and reliability of the data results from the basic deposition that relies on the thermodynamic equilibria of the polymers. New technologies are therefore generally compared to the dipping assembly method as the standard technique. However, despite the many advantages and wide availability of applicable materials, some challenges still exist. Firstly, LbL assembly has proven to be a markedly simple and innovative fabrication technique, but its implementation is hindered by its time-consuming nature. Constructing a single bilayer film typically takes 10 minutes of dipping in each polyelectrolyte solutions and then 2 minutes, 1 minute and 1 minute of each washing steps, so 28 minutes at least. Hence, it might take about 5 h for the assembly of a 10 bilayer film. Even spraying and spin coating methods, well-known as faster LbL self-assembly techniques, still need significant time for the preparation of multilayer nanofilms. There is also the limitation in making a selective film on a single substrate because most of the conventional techniques for fabricating nanofilms onto planar surfaces governed by the size and shape of the substrate. In other words, it is fairly difficult to combine more than two different films or partially deposited films onto a single substrate. In addition, from the clinical point of view, it is necessary for treatments on the chair-side to be delivered by simple methods. Preceding research has covered site-selective LbL assembly25,26 but it is hardly applicable for dental, clinical, or biomedical purposes generally performed on the chair-side by doctors, not in a laboratory.
In this study, we investigated the brushing LbL assembly technique in comparison with the conventional dipping method. By overcoming the limitations of the conventional LbL techniques, the potential for the application of the brushing LbL method for dental, clinical, or biomedical purposes is proved. In the past few decades, polysaccharide biopolymers such as alginate and chitosan have been frequently studied for drug delivery, micro- or nano-sized particles, and tissue engineering, because of their biocompatibility, non-immunogenic responses, and easily modified properties by pH control27,28,29,30,31. Therefore, we chose chitosan and alginate as the building blocks of the multilayer film prepared by the brushing LbL technique. Assembly was followed by thickness measurements, atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, quartz crystal microbalance (QCM) measurements, and contact angle analysis to characterize the films and their properties and compare them to those fabricated with the conventional dipping method. In addition, we used a PEG-b-PCL block copolymer for constructing micelles to act as hydrophobic drug carriers incorporated with dexamethasone (Dex), which is a well-known osteogenesis-inducing drug32,33. To determine the drug delivery properties, we measured the release profiles of the model drug, degradation profile of the multilayer film, and toxicity of the released solution.
Materials and Methods
Materials
Poly(acrylic acid) (PAA, M.W. = 1800), alginic acid sodium salt (Alginate, ALG, product number 180947), and chitosan (CHI, medium molecular weight) were purchased from Sigma-Aldrich. Poly(allylamine hydrochloride) (PAH, M.W. = 12000–200000) was purchased from Polysciences Inc., USA. We used fluorescein isothiocyanate isomer I (FITC, M.W. = 389.38,) to prepare a fluorescent conjugated polymer, PAH-FITC. We synthesized FITC-labeled PAH following a previously published procedure34. We prepared coumarin 6 (M.W. = 350.43, ≥99%) as a model drug for measuring the release profiles and used dexamethasone (D4902) as a model osteogenesis-inducing drug. FITC, coumarin 6 fluorescence dyes and dexamethasone were purchased from Sigma-Aldrich. Poly(ethylene glycol)-block-poly(ε-caprolactone) (PEO5K-b-PCL10K) was obtained from Polysciences Inc., USA, for constructing the PEO-b-PCL micelles. Organic solvent, N,N-dimethylformamide (DMF, D0558), were purchased from Samchun, Korea. We obtained paint brushes (series 948 #4, 11.5 mm width) from HwaHong, Korea. Phosphate buffered saline (PBS) 10X was obtained from Gibco® Life Technologies.
Synthesis of dexamethasone- and coumarin 6-loaded micelles
A few methods for preparing PEO-b-PCL block copolymer micelles have been reported2,3,35. We prepared the block copolymer micelles using a modification of a previously published method35. The PEO5K-b-PCL10K block copolymer solution was prepared at a concentration of 5 mg/mL in N,N-dimethylformamide (DMF). 2 mg of dexamethasone was then dissolved into the block copolymer solution. Using a 100 μL pipet, we transferred the solution into 20 mL of deionized water (DIW), without adjusting the pH, under vigorous stirring at 1500 rpm. As a result, crew-cut type Dex-loaded micelles were assembled with a hydrophobic interior containing the drug. After 1 h to allow stabilization, we used a 0.2 μm pore size syringe filter to remove the aggregated micelles to achieve a uniform size distribution in the solution. Subsequently, the micelle solution was dialyzed for 3 days in DIW to remove the remaining organic solvent. The micelle size was measured by the Dynamic Light Scattering(DLS) machine. (SZ-100, Horiba) For the coumarin 6-loaded micelles, which were prepared as a model drug carrier, we simply added 1 mg of the coumarin 6 into the PEO5K-b-PCL10K block copolymer solution instead of the dexamethasone.
Preparation of film substrates and polyelectrolyte solutions
We fabricated the multilayer films on a silicon wafer by the LbL assembly method using PAA, PAH, CHI, ALG, and the Dex-loaded PEO-b-PCL block copolymer micelle solutions. For the LbL assembly based on intermolecular electrostatic interactions, silicon wafers and glass substrates were prepared by a 2 min oxygen plasma treatment to become negatively charged with O2 plasma treatment machine. (CUTE-1B, Femto science, Korea) The concentrations of the PAA and CHI solutions were 5.0 mg/mL. Both PAH and FITC were added at 10.0 mg/mL to give the PAH-FITC solution. ALG was added at 5.0 mg/mL to the Dex-loaded PEO-b-PCL block copolymer micelle solution. The pH values of the polyelectrolyte solutions were adjusted as follows: PAA, pH 4.0; PAH-FITC, pH 8.0; CHI, pH 5.0; ALG + micelle blend, pH 2.5. The pH influences the ionization of amine and carboxyl groups and the surface charge density of the materials used36. The pH values of the solutions were controlled using 0.1 M HCl and 0.1 M NaOH solutions and measured via benchtop pH meter (HI 2211 PH/ORP meter, HANNA instruments).
Preparation of multilayer thin films fabricated by conventional LbL self-assembly and the brushing LbL method
We fabricated multilayer thin films by conventional LbL self-assembly19,37 and the brushing LbL method. Firstly, for the conventional LbL method, the treated substrate (silicon wafer or glass) was dipped into the positively charged (PAH, PAH-FITC, or CHI) solution for 10 min. Then, the substrate was washed three times for 2, 1, and 1 min each in DIW. The substrate was then dipped into the negatively charged (PAA, ALG, or ALG + micelle) solution for 10 min and followed by the same washing steps. This cycle produced a single bilayer of positively and negatively charged polyelectrolytes; we repeated this cycle until the intended number of bilayers was deposited.
To prepare thin films by the brushing LbL method, a substrate fixed on a supporting wall was brushed with a polyelectrolyte solution and washed three times with DIW using a disposable pipet. The substrate was dried simply using an air gun before brushing the next polyelectrolyte solution. We repeated these steps to stack the chitosan and alginate + Dex-loaded micelle blend layers until a specific number of bilayers (n) was reached to obtain the (CHI/ALG + micelle blend) n multilayer thin film. Additionally, for fabricating the multilayer films on the QCM electrode, we used a 50 ml conical tube as the supporting wall and hold the edge of it with tweezers to avoid other unexpected motion.
Characterization of the multilayer thin films
The thicknesses of the multilayer thin films were measured using a profilometer (Dektak 150, Veeco). The total mass of material deposited in each layer was obtained by a QCM (QCM200, 5 MHz, Stanford Research Systems). The root-mean-square (rms) roughness, Rq, and surface topography were measured with an AFM (NX10, Park Systems). The static contact angles (SCA) were measured under ambient conditions by a contact angle goniometer designed in our laboratory. Five 4 μL water droplets were imaged on each sample with a charge-coupled device (CCD) camera (IMT 3, IMT Solutions) and the free ImageJ software and the LB-ADSA plugin were used for contact angle analysis. FT-IR spectra were investigated to characterize the interaction between ALG and the Dex-loaded block copolymer micelles.
Drug release profiles of the multilayer thin films
For investigating the release profile of the coumarin 6 model drug, a (CHI/ALG + micelle blend)50 multilayer film was immersed in 5 mL PBS (1X) mixed with ethanol (EtOH; PBS/EtOH = 7:3) and incubated at a certain pH and temperature. Ethanol was added because the hydrophobic coumarin 6 was insoluble in PBS. Afterwards, 0.5 mL of the solution was collected at regular intervals and added to 0.5 mL of normal PBS. The fluorescence spectra of the coumarin 6 released into the PBS at each stage was measured by a microplate reader (Synergy H1 Hybrid Multi-Mode Microplate Reader, BioTek, USA). The concentrations of coumarin 6 were obtained from a calibration curve calculated by the fluorescence emission (λex = 480 nm, λem = 520 nm). Additionally, we measured the decrease in film thickness in PBS and 7:3 PBS/EtOH (pH 7.4) solutions at 37 °C to investigate film stability and the deconstruction of the multilayer.
Cytotoxicity effect of the nanofilms by an MTT assay
To test the cell viability of the nanofilms by an MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay, we seeded HeLa cells into a 12-well plate at 1 × 105 cells per well, and cultivated the cells overnight to attach them to the film surface (n = 3). The culture medium was removed and replaced with fresh medium and the released solution from the film were replaced. After 1 day incubation, 10% MTT in PBS (5 mg/mL) was incubated with Dulbecco’s Modified Eagle Medium (DMEM) for 2 h. The relative amounts of viable cells were compared by reading the optical density at a wavelength of 540 nm. The growth medium consisted of DMEM (Gibco) with 10% fetal bovine serum (Welgene, Gyeongsan-si, Korea), and 1% penicillin/streptomycin (Gibco).
Results and Discussion
Brush-based layer-by-layer deposition sequence
We have introduced a brush-based LbL self-assembly method, described in detail in the schematic illustration in Fig. 1a, where purple represents cations such as chitosan, green represents anions like alginate, and the yellow round particles represent block copolymer micelles containing dexamethasone. For the brushing LbL process, we simply placed the substrates on a wall or other supporting structure oriented vertically on a bench, then we brushed them twice with a polycation solution followed by three rinsing steps with the disposable pipet from top to bottom. Since the substrate surfaces were negatively charged due to the oxygen plasma treatment, we introduced a positively charged solution first. After drying with a blower, we applied a polyanion solution to the substrates by brushing, followed by the rinsing steps. This process resulted in a single bilayer; hence, it was repeated until the desired film thickness was accomplished. Previous research normally used 1 mg/mL polyelectrolyte solutions, which is high enough to construct multilayer films driven by the thermodynamic stabilization of the polyelectrolytes, and the adsorption usually does not depend on the polymer concentration19,38. For the brushing LbL method, solution concentrations higher than the general of 5 mg/mL were required, because the film tore off easily after 10 bilayers when using 1 mg/mL of each polycation and polyanion (See Supplementary Fig. S1). The higher concentration gave a uniform film thickness, unlike the 1 mg/mL case from Supplementary Fig. S1a, and viscous properties that made it possible to fabricate films onto the substrate selectively.
(a) Schematic illustration of the brushing layer-by-layer (LbL) self-assembly process on a flat substrate. Photographs of the (PAH-FITC/PAA) n (n = number of bilayers) multilayer films prepared by brushing LbL on a glass slide under (b) visible light and (c) ultraviolet (UV) light (λ = 254) (The Fig. 1a is representing brushing LbL process and it was drawn by K.P.).
We proved the possibility of site-selective deposition via the differences in fluorescence intensity and the depth of color. Figure 1b,c show that the color of the (PAH-FITC/PAA) n multilayer film depends on the number of bilayers, n. As the number of bilayers increased, the fluorescence intensity under a hand UV-vis was stronger and the color deepened, resulting from the increased amount of FITC-conjugated PAH. Thus, we could fabricate films of different thicknesses onto a single glass substrate in any desired pattern or shape. Also, with relatively short process time and enough washing steps, we could construct uniform structure through the substrate. By applying the basic processes of classic LbL assembly to the brushing LbL method, we could take advantage of the favorable aspects of the conventional method by controlling the structure, thickness, uniformity, and morphology of the film through the interaction of the materials at the molecular level19,39.
Film characterization
The LbL assembly of the polyelectrolyte film by the dipping and brushing methods is compared in Fig. 2. The polyelectrolyte solutions used for both deposition methods were the same and the deposition times were standardized to 10 s and 10 min. Figure 2a–e show that dipping and brushing for 10 s lead to the same growth tendencies, and result in more uniform film morphologies than that with the 10 min dipping method (Fig. 2c). The film thickness growth curves show negligible error bars for both 10 s dipping and brushing procedures, and relatively large error bars for 10 min dipping. Furthermore, the rms surface roughness, Rq, of the sample fabricated with 10 min dipping is about seven times greater those of the samples fabricated with the other methods. In addition, the thickness of the 10 min dipping film is almost 10 times thicker (1.3 μm for dipping for 10 min and about 150 nm for 10 s brushing). This significant difference between the two methods is attributed to the inter-diffusion of neighboring layers.
Comparison of the conventional dipping LbL and brushing LbL methods. (a) Thickness growth curves of a (CHI/ALG + micelle blend)n multilayer film up to n = 20, fabricated by dipping for 10 min (blue triangles), dipping for 10 s (red circles), and brushing for 10 s (black squares) at two-bilayer intervals. (b) FT-IR transmission spectra of the multilayer films fabricated by 10 s brushing LbL (top, black), 10 s dipping LbL (middle, red), and the difference between the two (bottom, green). Topographic images of the multilayer films fabricated with the different methods: (c) dipping for 10 min, (d) dipping for 10 s, and (e) brushing for 10 s.
Surface rearrangements take place slowly, while absorbed polyelectrolytes interact with ionized counter polyelectrolytes and attain an equilibrium, or steady-state, over several minutes40,41,42,43. The brushing LbL technique has a relatively short polymer solution contact time; hence, it has a slight inter-diffusion effect, while the classical dipping method leads to inter-diffusion between neighboring layers and a rough surface morphology.
The thickness of the multilayer film prepared by the 10 s brushing LbL procedure indicated linear growth as the number of bilayers increased; the thickness of the 50 bilayer film was 376 ± 18 nm, as shown in Fig. 3a. (The inset of this figure compares the growth curves for the 10 s brushing and 10 s dipping methods for 20 bilayers from Fig. 2a.) The average thickness increment was 7.53 nm per bilayer, which corresponds to the 7.46 nm value obtained from the inset. Both results show the advantages of the brushing LbL method: it can control the film thickness on the nanoscale as well as produce a uniform surface morphology, while the classical dipping method effectuates bulk thickness growth per bilayer.
Characterization of the 10 s brushing LbL method by thickness measurement, QCM analysis, and contact angle measurement. (a) Thickness growth curves of the (CHI/ALG + micelle blend) n multilayer films up to n = 50. Inset: Comparison of the dipping and brushing methods for 20 bilayers. (b) QCM analysis of the multilayer films up to 14 layers fabricated by the brushing LbL method. (c) Static contact angles measurements depending on the alternating outermost layer of the films fabricated by the brushing LbL method. For (b) and (c), the odd number of layers named as CHI represent chitosan layer and the even number of layers named as ALG represent the ALG + micelle blend outer layers, respectively.
To demonstrate that the multilayer film prepared by the brushing method also sequentially adhered onto the substrate, i.e., in the layer-by-layer fashion, we performed contact angle and QCM analysis after the deposition of each layer. Figure 3c demonstrates the different contact angles obtained depending on the identity of the outermost layer. The CHI layer and ALG + block copolymer micelle layers were both hydrophilic but with different degrees. For the CHI layer, the SCA was around 22°, and for the ALG + micelle layer, it was approximately half that about 12°. The hydrophilic behavior of both polymer materials is attributed to specific functional groups, such as the hydroxyl and carboxylic groups of ALG and the amine and hydroxyl groups of CHI. Also, the morphology of the multilayer films could affect it. It appeared the polyanion layer composed of ALG and PEG-containing block copolymer micelles has the greater hydrophilicity rather than CHI layer. This might be affected by the well-known hydrophilic characteristic of PEG44,45 and rough surface topography of the micelle-containing deposited layer. Thus, we could prove the alternative deposition of the multilayer films via contact angle analysis.
From the QCM data, we could evaluate the sequential layer deposition based on the frequency decrease that is proportional to the increased mass of the deposited layer. In Fig. 3b, odd number of layers represents the CHI layers and the even number of layers represents the ALG + block copolymer micelle layer. From the figure, we could observe the stepwise decrease of the QCM electrode’s frequency as the number of layers increased. For CHI and ALG + block copolymer micelle layers, each material demonstrated a 34.59 ± 6.45 Hz and 36.29 ± 4.08 Hz frequency decrease on average per layer, respectively, after the 6th layer. The exact linear decrease indicates the 10 s brushing method successfully built the film by Layer-by-Layer assembly. And the QCM results from the conventional method with 10 s and 10 min dipping has the same decreasing tendency of the frequency. (See Supplementary Fig. S2) The unexpected peak from 4th layer from the Supplementary Fig. S2b is because of bulk adsorption by the dipping method. From these results, we determined that it is possible to fabricate multilayer films by LbL self-assembly using the brushing method.
Preparation and characterization of the micelle blend and its incorporation
As we prepared the micelles with PEO5K-b-PCL10K following the previous method35, the micelles could have a crew-cut structure which has a relatively large core than its corona. The PEO part is constituted as corona46,47,48,49. The average size of the micelles was 118 ± 38.1 nm, measured by dynamic light scattering (DLS) machine. It is a trustworthy result as it compares well with previous data2,50. PEO, which forms the corona of the block copolymer micelle, is utilized as a hydrogen bonding acceptor because of its ether group. ALG interacts with PEO as a hydrogen bond donor based on the abundant hydroxyl and carboxyl groups on its structure. For the negatively charged polyelectrolyte solution, we adjusted the pH of the ALG + micelle blend solution to 2.5 because, under the pKa of ALG (~3.5–4.4), it has more unionized hydroxyl and carboxyl groups that can act as hydrogen bonding donors. Thus, the hydrogen bonding between the donor hydroxyl and carboxyl groups on ALG and the acceptor parts of the PEO-b-PCL micelles made it possible to incorporate these micelles into the film. Figure 4 shows evidence of hydrogen bonding among the ALG and PEO-b-PCL micelles. As described in Fig. 4b, the absorption band at 1739.48 cm−1 (characteristic of the carboxyl C = O bond) of the ALG solution was shifted to 1725.98 cm−1 for the solution blended with the micelles. Also, the maximum absorbance of the peak related to the –OH group was shifted from 3433.64 cm−1 to 3410.49 cm−1 for the plain and blended solutions, respectively. Both red-shifted peaks were explained by the increased molecular interactions between each molecule based on hydrogen bonding. In addition, the characteristic peaks of PEO-b-PCL micelles at 1726.94 cm−1 and 2870.52 cm−1 (See Supplementary Fig. S3) appeared at Fig. 4c after the ALG and the block copolymer micelles are blended, compared to the pure ALG solution. It proves that the block copolymer micelles were well-incorporated with the ALG.
Film degradation and drug release
To employ this multilayer film for biomedical purposes, we investigated the film degradation and release profiles, and the cell toxicity of the released solution. Firstly, we measured the fluorescence excitation and emission of the coumarin 6 released from the multilayer film. We simply immersed the multilayer film in 5 mL 7:3 PBS:EtOH solution and took out a small amount of the solution at the indicated time intervals. We introduced ethanol since the coumarin 6, a hydrophobic model drug, was not released from the multilayer film in the 100% PBS solution (See Supplementary Fig. S4). As represented in Fig. 5b, about 80% of the coumarin 6 model drug was released from the multilayer film after 2 days and then more was slowly released until 14 days. The amount of released coumarin 6 was quantified by photoluminescence at an excitation wavelength of λex = 480 nm and an emission wavelength of λem = 520 nm. The final concentration of the released solution was 8.621 ng/mL, i.e., 21.9 nM, which is above the typical 10 nM dexamethasone concentration of osteogenic media51. The molecular weight and structures of coumarin 6 and dexamethasone are similar whilst the latter can slightly dissolve in PBS, so we inferred that more than the typical concentration of dexamethasone required for osteogenic media could be released from the multilayer film.
Characteristics of the (CHI/ALG + micelle blend)50 multilayer films related to their inherent disassembly behavior. (a) Film degradation and (b) cumulative release profile of coumarin 6 as a model drug in 7:3 PBS:EtOH (pH 7.4) performed in an incubator at 37 °C. (c) Film degradation behavior in 100% PBS (pH 7.4) at 37 °C. (d) Cytotoxic effects of the PBS solution of (c).
For analyzing the degradation profile, we measured the thickness of a multilayer film at the same time intervals as used to obtain the release profile. Figure 5a shows the thickness of a (CHI/ALG + micelle blend)50 film stored in 7:3 PBS:EtOH solution in an incubator at 37 °C. Figure 5c shows the degradation profile in 100% PBS under the same conditions. Both graphs show a similar tendency of degradation. At pH 7.4, the ratio of protonated amine groups from CHI lessened, so the electrostatic interactions among the building blocks were weakened52. Thus, the thickness of each film increased slightly for the first 15 min because of the swelling effect. Then, they decreased gradually until each film reached its final thickness. For Fig. 5a, the thickness of the film immersed in the PBS:EtOH mixed solution decreased from 370 to 240 nm and then saturated, losing 35% of its initial thickness. For the film immersed in the 100% PBS solution, the thickness decreased from 360 to 230 nm, losing 36% of its initial thickness. Considering that chitosan and alginate have very low solubilities in EtOH compared to water, shown in a previous study, a relatively slow film degradation in the 70% PBS and 30% EtOH solution is a reasonable result53. In addition, to verify the toxicity of the released solution for further in vitro and in vivo experiments, a cytotoxic test was carried out. From Fig. 5d, the released sample shows almost the same result as the control, a cell-growth medium. The released sample also showed a slightly higher cell viability than the PBS control, which means the film materials do not have any toxic effect on the cells.
Conclusion
In this study, we have demonstrated the brushing layer-by-layer assembly method, which is simple and faster compared to the conventional surface coating method. We also demonstrated the possibility of the site-selective deposition of drug release films with different thicknesses. In addition, we have proved that the brush-based fabrication method is based on the principles of layer-by-layer self-assembly by comparing the Atomic force microscopy and Fourier transform infrared spectroscopy data of this method and the classical methods. Static contact angle and Quartz crystal microbalance measurements also supported this finding. For functionalized multilayer films for biomedical applications, we introduced block copolymer micelles incorporated with dexamethasone and investigated the cytotoxicity and release profile. On the basis of this research, the brushing layer-by-layer method represents a new layer-by-layer assembly technique for clinical purposes.
References
Otsuka, H., Nagasaki, Y. & Kataoka, K. PEGylated nanoparticles for biological and pharmaceutical applications. Adv Drug Del Rev. 55, 403–419 (2003).
Deng, H. et al. PEG-b-PCL copolymer micelles with the ability of pH-controlled negative-to-positive charge reversal for intracellular delivery of doxorubicin. Biomacromolecules. 15, 4281–4292 (2014).
Giacomelli, C. & Borsali, R. Morphology of Poly (ethylene oxide)‐block‐Polycaprolatone Block Copolymer Micelles Controlled via the Preparation Method. Macromolecular Symposia. 245, 147–153 (2006).
Tian, H. et al. Biodegradable cationic PEG–PEI–PBLG hyperbranched block copolymer: synthesis and micelle characterization. Biomaterials. 26, 4209–4217 (2005).
Kataoka, K. Design of nanoscopic vehicles for drug targeting based on micellization of amphiphiuc block copolymers. Journal of Macromolecular Science, Part A. 31, 1759–1769 (1994).
Yokoyama, M. et al. Toxicity and antitumor activity against solid tumors of micelle-forming polymeric anticancer drug and its extremely long circulation in blood. Cancer Res. 51, 3229–3236 (1991).
Masayuki, Y. et al. Polymer micelles as novel drug carrier: adriamycin-conjugated poly (ethylene glycol)-poly (aspartic acid) block copolymer. J Control Release. 11, 269–278 (1990).
Beroström, K. et al. Effects of branching and molecular weight of surface-bound poly (ethylene oxide) on protein rejection. J Biomater Sci Polym Ed. 6, 123–132 (1995).
Peracchia, M. T. et al. Pegylated nanoparticles from a novel methoxypolyethylene glycol cyanoacrylate-hexadecyl cyanoacrylate amphiphilic copolymer. Pharm Res. 15, 550–556 (1998).
Cref, R. et al. Biodegradable long circulating polymer nanospheres. Science. 263, 1600–1603 (1994).
Zhou, J. et al. Preparation and enhanced structural integrity of electrospun poly (ε-caprolactone)-based fibers by freezing amorphous chains through thiol-ene click reaction. Colloids Surf Physicochem Eng Aspects. 538, 7–13 (2018).
Kim, B.-S., Park, S. W. & Hammond, P. T. Hydrogen-bonding layer-by-layer-assembled biodegradable polymeric micelles as drug delivery vehicles from surfaces. Acs Nano. 2, 386–392 (2008).
Han, U., Y. Seo & J. Hong. Effect of pH on the structure and drug release profiles of layer-by-layer assembled films containing polyelectrolyte, micelles, and graphene oxide. Sci Rep. 6 (2016).
Ariga, K., Lvov, Y. M., Kawakami, K., Ji, Q. & Hill, J. P. Layer-by-layer self-assembled shells for drug delivery. Adv Drug Del Rev. 63, 762–771 (2011).
Guo R. et al. Sandwiched Fe3O4/Carboxylate Graphene Oxide Nanostructures Constructed by Layer-by-Layer Assembly for Highly Efficient and Magnetically Recyclable Dye Removal. ACS Sustainable Chemistry & Engineering (2017).
Zhao, X. et al. Facile fabrication of hierarchical diamond-based AuNPs-modified nanocomposites via layer-by-layer assembly with enhanced catalytic capacities. Journal of the Taiwan Institute of Chemical Engineers. 80, 614–623 (2017).
Zhao X. et al. Fabrication of Hierarchical Layer-by-Layer Assembled Diamond-based Core-Shell Nanocomposites as Highly Efficient Dye Absorbents for Wastewater Treatment. Sci Rep. 7 (2017).
Richardson, J. J., Björnmalm, M. & Caruso, F. Technology-driven layer-by-layer assembly of nanofilms. Science. 348, aaa2491 (2015).
Decher, G. Fuzzy nanoassemblies: toward layered polymeric multicomposites. Science. 277, 1232–1237 (1997).
Jeong, H. et al. Durable urushiol-based nanofilm with water repellency for clear overlay appliances in dentistry. ACS Biomaterials Science & Engineering. 2, 344–348 (2016).
Zhang, R. et al. Carrier-free, chemophotodynamic dual nanodrugs via self-assembly for synergistic antitumor therapy. ACS applied materials & interfaces. 8, 13262–13269 (2016).
Coustet, M. et al. Layer-by-layer assembly of polymersomes and polyelectrolytes on planar surfaces and microsized colloidal particles. J Colloid Interface Sci. 421, 132–140 (2014).
Zelikin, A. N. Drug releasing polymer thin films: new era of surface-mediated drug delivery. Acs Nano. 4, 2494–2509 (2010).
Zhang X., H. Chen & H. Zhang. Layer-by-layer assembly: from conventional to unconventional methods. Chemical Communications. 1395–1405 (2007).
Kim, H.-J., Lee, K., Kumar, S. & Kim, J. Dynamic sequential layer-by-layer deposition method for fast and region-selective multilayer thin film fabrication. Langmuir. 21, 8532–8538 (2005).
Shi, L. et al. Site-selective lateral multilayer assembly of bienzyme with polyelectrolyte on ITO electrode based on electric field-induced directly layer-by-layer deposition. Biomacromolecules. 4, 1161–1167 (2003).
Trigueiro, J. P. C., Silva, G. G., Pereira, F. V. & Lavall, R. L. Layer-by-layer assembled films of multi-walled carbon nanotubes with chitosan and cellulose nanocrystals. J Colloid Interface Sci. 432, 214–220 (2014).
Yan, X. L., Khor, E. & Lim, L. Y. Chitosan‐alginate films prepared with chitosans of different molecular weights. Journal of Biomedical Materials Research Part A. 58, 358–365 (2001).
Li, P., Dai, Y.-N., Zhang, J.-P., Wang, A.-Q. & Wei, Q. Chitosan-alginate nanoparticles as a novel drug delivery system for nifedipine. Int J Biomed Sci. 4, 221–228 (2008).
Lawrie, G. et al. Interactions between alginate and chitosan biopolymers characterized using FTIR and XPS. Biomacromolecules. 8, 2533–2541 (2007).
Yuan, W. et al. pH-controlled construction of chitosan/alginate multilayer film: characterization and application for antibody immobilization. Langmuir. 23, 13046–13052 (2007).
Rickard, D., Sullivan, T., Shenker, B., Leboy, P.a. & Kazhdan, I. Induction of rapid osteoblast differentiation in rat bone marrow stromal cell cultures by dexamethasone and BMP-2. Dev Biol. 161, 218–228 (1994).
Coelho, M. & Fernandes, M. Human bone cell cultures in biocompatibility testing. Part II: effect of ascorbic acid, β-glycerophosphate and dexamethasone on osteoblastic differentiation. Biomaterials. 21, 1095–1102 (2000).
Hau, W. L., Trau, D. W., Sucher, N. J., Wong, M. & Zohar, Y. Surface-chemistry technology for microfluidics. Journal of micromechanics and microengineering. 13, 272 (2003).
Vangeyte, P., Gautier, S. & Jérôme, R. About the methods of preparation of poly (ethylene oxide)-b-poly (ε-caprolactone) nanoparticles in water: Analysis by dynamic light scattering. Colloids Surf Physicochem Eng Aspects. 242, 203–211 (2004).
Choi, J. & Rubner, M. F. Influence of the degree of ionization on weak polyelectrolyte multilayer assembly. Macromolecules. 38, 116–124 (2005).
Shiratori, S. S. & Rubner, M. F. pH-dependent thickness behavior of sequentially adsorbed layers of weak polyelectrolytes. Macromolecules. 33, 4213–4219 (2000).
Decher, G., Hong, J. & Schmitt, J. Buildup of ultrathin multilayer films by a self-assembly process: III. Consecutively alternating adsorption of anionic and cationic polyelectrolytes on charged surfaces. Thin solid films. 210, 831–835 (1992).
Jeong, H. et al. Intrinsic Hydrophobic Cairnlike Multilayer Films for Antibacterial Effect with Enhanced Durability. ACS applied materials & interfaces. 7, 26117–26123 (2015).
Schlenoff, J. B., Dubas, S. T. & Farhat, T. Sprayed polyelectrolyte multilayers. Langmuir. 16, 9968–9969 (2000).
Schlenoff, J. B., Ly, H. & Li, M. Charge and mass balance in polyelectrolyte multilayers. J Am Chem Soc. 120, 7626–7634 (1998).
Raposo, M., Pontes, R., Mattoso, L. & Oliveira, O. Kinetics of adsorption of poly (o-methoxyaniline) self-assembled films. Macromolecules. 30, 6095–6101 (1997).
Tsukruk, V. et al. Electrostatic deposition of polyionic monolayers on charged surfaces. Macromolecules. 30, 6615–6625 (1997).
Harris, J. M. Poly (ethylene glycol)chemistry: biotechnical and biomedical applications. (Springer Science & Business Media, New York, NY, USA, 2013).
Delgado, C., Francis, G. E. & Fisher, D. The uses and properties of PEG-linked proteins. Crit Rev Ther Drug Carrier Syst. 9, 249–304 (1991).
Halperin A., M. Tirrell & T. Lodge Tethered chains in polymer microstructures, in Macromolecules: Synthesis, Order and Advanced Properties., Springer. p. 31–71 (1992).
Zhang, L., Yu, K. & Eisenberg, A. Ion-induced Morphological Changes in” Crew-Cut” Aggregates of Amphiphilic Block. Science. 272, 1777 (1996).
Zhang, L. & Eisenberg, A. Formation of crew‐cut aggregates of various morphologies from amphiphilic block copolymers in solution. Polymers for Advanced Technologies. 9, 677–699 (1998).
Zhang, L. & Eisenberg, A. Multiple morphologies and characteristics of “crew-cut” micelle-like aggregates of polystyrene-b-poly (acrylic acid) diblock copolymers in aqueous solutions. J Am Chem Soc. 118, 3168–3181 (1996).
Chiappetta, D. A. & Sosnik, A. Poly (ethylene oxide)–poly (propylene oxide) block copolymer micelles as drug delivery agents: improved hydrosolubility, stability and bioavailability of drugs. Eur J Pharm Biopharm. 66, 303–317 (2007).
Hong, J. et al. Multilayer thin-film coatings capable of extended programmable drug release: application to human mesenchymal stem cell differentiation. Drug delivery and translational research. 2, 375–383 (2012).
Sæther, H. V., Holme, H. K., Maurstad, G., Smidsrød, O. & Stokke, B. T. Polyelectrolyte complex formation using alginate and chitosan. Carbohydrate Polymers. 74, 813–821 (2008).
Shaji, J., Jain, V. & Lodha, S. Chitosan: a novel pharmaceutical excipient. Int. J. Pharm. Appl. Sci. 1, 11–28 (2010).
Acknowledgements
This research was supported by the Chung-Ang University Graduate Research Scholarship in 2017. This research was supported by a grant of the Korea Health Technology R&D Project through the Korea Health Industry Development Institute (KHIDI), funded by the Ministry of Health &Welfare, Republic of Korea (HI14C-3266).
Author information
Authors and Affiliations
Contributions
Designing the concept of the research: J.H. and K.P. Performed experiments and analyzed the results: K.P. Interpreted the data and wrote the manuscript: K.P. MTT assay, providing experiment section for MTT assay and Figure 5d: D.C. All authors reviewed and approved the final version of the manuscript for submission with approval of J.H.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Park, K., Choi, D. & Hong, J. Nanostructured Polymer Thin Films Fabricated with Brush-based Layer-by-Layer Self-assembly for Site-selective Construction and Drug release. Sci Rep 8, 3365 (2018). https://doi.org/10.1038/s41598-018-21493-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-21493-9
- Springer Nature Limited
This article is cited by
-
Synthesis, characterization, and cytotoxicity assay of γ-Fe2O3 nanoparticles coated with quercetin-loaded polyelectrolyte multilayers
Colloid and Polymer Science (2022)
-
Developing regulatory property of gelatin-tannic acid multilayer films for coating-based nitric oxide gas delivery system
Scientific Reports (2019)
-
Synthesis of photoluminescent zinc acetate–polyethylene composite coatings by pulse laser-assisted electron beam dispersion
Journal of Materials Science (2018)