Abstract
Faster-than-Nyquist (FTN) signal achieves higher spectral efficiency and capacity compared to Nyquist signal due to its smaller pulse interval or narrower subcarrier spacing. Shannon limit typically defines the upper-limit capacity of Nyquist signal. To the best of our knowledge, the mathematical expression for the capacity limit of FTN non-orthogonal frequency-division multiplexing (NOFDM) signal is first demonstrated in this paper. The mathematical expression shows that FTN NOFDM signal has the potential to achieve a higher capacity limit compared to Nyquist signal. In this paper, we demonstrate the principle of FTN NOFDM by taking fractional cosine transform-based NOFDM (FrCT-NOFDM) for instance. FrCT-NOFDM is first proposed and implemented by both simulation and experiment. When the bandwidth compression factor α is set to 0.8 in FrCT-NOFDM, the subcarrier spacing is equal to 40% of the symbol rate per subcarrier, thus the transmission rate is about 25% faster than Nyquist rate. FTN NOFDM with higher capacity would be promising in the future communication systems, especially in the bandwidth-limited applications.
Similar content being viewed by others
Introduction
In the 1940s, an upper limit of communication capacity was proposed for Nyquist signal in an additive white Gaussian noise (AWGN) channel, now known as the Shannon limit1, 2. Initially, the communication capacity is enough for the traditional data and voice services. However, with the exponential growth of data traffic due to bandwidth-intensive applications such as high definition TV and mobile video, the communication capacity gradually approaches Shannon limit nowadays3,4,5. Increasing the spectral efficiency is a key challenge to meet the increasing demand for higher capacity over communication channels. Faster-than-Nyquist (FTN) signal was first proposed by Mazo in 1970s to improve the spectral efficiency6. As the name implies, FTN signal can achieve a symbol rate faster than Nyquist rate. Therefore, it has been widely investigated in high-capacity wireless and optical communications7,8,9,10,11,12,13.
The reported FTN scheme can be generally categorized into two types, one is compressing the duration between the adjacent pulses in time domain6, and the other one is compressing the baseband bandwidth in frequency domain12,13,14. In time domain, FTN binary sinc-pulse signal was proposed in 1975 by accelerating the pulse with time acceleration factor τ. The accelerated pulses are no longer orthogonal, thus FTN binary sinc-pulse signal is a kind of FTN non-orthogonal time-division multiplexing (NOTDM) signal. When τ is set to 0.8, known as the Mazo limit, 25% more bits can be carried in the same bandwidth and there is not obvious deterioration in bit error rate (BER) performance by using the trellis decoding to effectively compensate the inter-symbol interference (ISI)7. In frequency domain, the duobinary-pulse shaping filter is employed to compress the baseband bandwidth of single-carrier signal12, 13 or the subcarrier spacing of multi-carrier signal is compressed to obtain narrower baseband bandwidth14. In this paper, we focus on the multi-carrier FTN signal. Non-orthogonal frequency-division multiplexing (NOFDM) signal has been realized by further compressing the subcarrier spacing compared to OFDM signal15,16,17. We found that only when the subcarrier spacing is less than half of the symbol rate per subcarrier, NOFDM signal can achieve a symbol rate faster than Nyquist rate as we demonstrated in our recent work14.
FTN signal achieves higher spectral efficiency and capacity compared to Nyquist signal due to its smaller pulse interval or narrower subcarrier spacing. Shannon limit typically defines the upper-limit capacity of Nyquist signal. In this paper, we first give the mathematical expression for the capacity limit of FTN NOFDM signal. The mathematical expression shows that FTN signal has the potential to achieve a higher capacity limit compared to Nyquist signal. In this paper, we demonstrate the principle of FTN NOFDM by taking fractional cosine transform-based NOFDM (FrCT-NOFDM) for instance. FrCT-NOFDM is first proposed and implemented by both simulation and experiment. When the bandwidth compression factor α is set to 0.8, the subcarrier spacing is equal to 40% of the symbol rate per subcarrier, thus transmission rate is about 25% faster than Nyquist rate.
Results
In this paper, we demonstrate the principle of FTN NOFDM by taking FrCT-NOFDM for instance. A block diagram of the FrCT-NOFDM system is depicted in Fig. 1. Different from traditional OFDM system, the inverse FrCT (IFrCT)/FrCT algorithm is employed to implement the multiplexing/demultiplexing processing. The N-order IFrCT and FrCT are defined as
where 0 ≤ n ≤ N − 1, 0 ≤ k ≤ N − 1,
and α is the bandwidth compression factor. The α less than 1 determines the level of the bandwidth compression. When α is equal to 1, Equation 2 is the Type-II discrete cosine transform (DCT) in which the matrix is orthogonal. The Type-II DCT is probably the most commonly used form, and is often simply referred to as “the DCT”18. DCT-based OFDM (DCT-OFDM) signal can be generated by Type-II DCT19, 20. In DCT-OFDM, the subcarrier spacing is equal to half of the symbol rate per subcarrier, which is half of the subcarrier spacing in discrete Fourier transform-based OFDM (DFT-OFDM). Therefore, the subcarrier spacing of DCT-OFDM is equal to 1/2T where T denotes the time duration of one DCT-OFDM symbol21, 22. Due to the compression of subcarrier spacing, the subcarrier spacing of FrCT-NOFDM should be smaller than 1/2T.
Spectral efficiency and capacity limit
Figure 2 shows the sketched spectra of DCT-OFDM (i.e., α = 1) and FrCT-NOFDM when the subcarrier number is set to 4. The subcarrier spacing of FrCT-NOFDM is equal to α/2T where T denotes the time duration of one FrCT-NOFDM symbol. All the subcarriers locate in the positive frequency domain. Meanwhile, their images fall into the negative frequency domain. When the subcarrier number is large enough, the baseband bandwidth of FrCT-NOFDM can be calculated by
where N denotes the subcarrier number.
In general, Nyquist frequency is equal to half of the sample rate, which is equal to N/2T. When N is large enough, the baseband bandwidth of DCT-OFDM (i.e., α = 1) is almost the same with Nyquist frequency and the baseband bandwidth of FrCT-NOFDM (i.e., α < 1) is smaller than Nyquist frequency. It is worth noting that Nyquist frequency should not be confused with Nyquist rate. Nyquist rate is defined as the twice of the baseband bandwidth,
As we know, the symbol rate of FrCT-NOFDM is equal to the sample rate when all the subcarriers are valid,
thus the symbol rate of FrCT-NOFDM is faster than Nyquist rate. FrCT-NOFDM can be considered as a kind of FTN signal. When α is set to 0.8, the subcarrier spacing is equal to 40% of symbol rate per subcarrier. Twenty percent baseband bandwidth saving can be obtained and the transmission rate is about 25% faster than the Nyquist rate.
Afterwards, we discuss the capacity limit for FrCT-NOFDM signal. The channel is in the presence of AWGN. The well-known Shannon limit for Nyquist signal can be calculated by
where W is the signal bandwidth, P S is the signal power and P N is the noise power. This equation depicts the upper-limit capacity of Nyquist signal2.
To obtain the capacity limit of FrCT-NOFDM signal, we will apply the analysis method for single-carrier signal in Shannon’s papers1, 2 to the multi-carrier signal. However, there is great difference between single-carrier and multi-carrier signal. The capacity limit of the single-carrier signal can be carried out in the time domain, but the capacity limit of multi-carrier signal should be derived out in the frequency domain. The derivation of capacity limit needs to employ the geometric methods23. In the following, we will briefly give the derivation of the capacity limit for FrCT-NOFDM. This derivation is similar to that in Shannon’s papers.
In the frequency domain, there are W/(subcarrier spacing) independent amplitudes where W is the baseband bandwidth and the subcarrier spacing is equal to α/2T. Therefore, the number of independent amplitudes is equal to 2TW/α, which determines the dimensions of signals. For large W, the perturbation caused by noise can be considered as some points near the surface of a sphere with radius \(\sqrt{2TW{P}_{N}/\alpha }\) centered at the signal point. The power of received signal is P S + P N . Similar to the perturbation, the received signal can be considered as some points whose positions are on the surface of a sphere with radius \(\sqrt{2TW({P}_{S}+{P}_{N})/\alpha }\). The number of the distinguishable signals is no more than the volume of the sphere with radius \(\sqrt{2TW({P}_{S}+{P}_{N})/\alpha }\) divided by the volume of the sphere with radius \(\sqrt{2TW{P}_{N}/\alpha }\). The volume of an n-dimensional sphere of radius r can be calculated by ref. 23
where \({\rm{\Gamma }}(n\mathrm{/2}+\mathrm{1)}={\int }_{0}^{\infty }\,{e}^{-t}\times {t}^{n\mathrm{/2}}dt\). Therefore, the upper limit for the number of distinguishable signals is given by
Consequently, the capacity limit of FrCT-NOFDM signal can be bounded by
It is worth noting that, in FrCT-NOFDM signal, inter-carrier interference (ICI) is a serious problem that should not be neglected because the subcarriers are no longer orthogonal. Figure 3 shows the probability density function (PDF) of ICI in FrCT-NOFDM with α of 0.8. The simulated curve denotes the PDF of the 2-PAM with ICI in FrCT-NOFDM with α of 0.8. The theoretical curve depicts the PDF of the 2-PAM with Gaussian noise, which can be defined as
where σ 2 is the variance of the Gaussian noise. The simulated curve agrees well with the theoretical curve. Therefore, the distribution of ICI is approximately Gaussian. Moreover, the ICI is independent of the Gaussian noise in AWGN channel. Considering both ICI and Gaussian noise in AWGN channel, the capacity limit of FrCT-NOFDM signal can be rewritten as
where P ICI is the power of ICI, which degrades the BER performance and thus decreases the capacity of FrCT-NOFDM signal. Therefore, the capacity of FrCT-NOFDM signal is likely to approach the capacity limit in Equation 10 only when ICI has been effectively eliminated. As verified in literatures6, 7, when the α is set to the value between 1 and 0.8, there is not obvious deterioration in BER performance by employing the optimal detection to eliminate the interference. The capacity limit of FrCT-NOFDM signal is potentially higher than that of the Nyquist signal when the α is set to the value between 1 and 0.8. How to eliminate the ICI is crucial for FrCT-NOFDM system. Afterwards, we will demonstrate the simulation and experiment to investigate the performance of FrCT-NOFDM system and verify the feasibility of the ICI cancellation algorithm.
Simulation and theoretical analysis
In this section, we will introduce an ICI cancellation algorithm based on iterative detection (ID) for FrCT-NOFDM. The simulations are demonstrated to verify the feasibility of FrCT-NOFDM. In the simulation system, the AWGN channel is employed. The number of subcarriers is set to 256 and the number of FrCT-NOFDM symbols is set to 4096. E b /N 0 denotes the ratio between the energy per bit and the single-sided noise power spectral density.
An N × N correlation matrix C is defined to study the ICI of FrCT-NOFDM, in which the interference between subcarriers l and m is represented by C l, m , the value of cross-correlation. When l equals to m, C l, m represents the auto-correlation value for each of the subcarriers. C l, m can be calculated by
Figure 4 presents the |C l, 128| as a function of l for DCT-OFDM (i.e., α = 1) and FrCT-NOFDM. When α is set to 1, the auto-correlation value for the 128th subcarrier is 1. In the same time, the cross-correlation values are almost equal to 0. Therefore, when α is set to 1, C is an identity matrix and the output of DCT is the OFDM signal. To achieve smaller subcarrier spacing, α can be set to be smaller than 1. However, when α is less than 1, the cross-correlation values are no longer equal to 0 and the orthogonality is destroyed. As shown in Fig. 4, the interference caused by the adjacent subcarriers is larger than that caused by farside subcarriers. The ICI increases with the decrease of α. Thus, BER performance of FrCT-NOFDM degrades with the decrease of α. When the subcarrier spacing is equal to the half of symbol rate per subcarrier, the subcarriers are orthogonal in DCT-OFDM, but the counterparts are no longer orthogonal in fractional Hartley transform NOFDM (FrHT-NOFDM)14 or fractional Fourier transform-based NOFDM (FrFT-NOFDM)15. Therefore, under the same subcarrier spacing, the ICI in FrCT-NOFDM should be smaller than that in FrHT-NOFDM or FrFT-NOFDM.
Recently, ID algorithm has been researched to eliminate the ICI for FrFT-NOFDM15,16,17. FrFT-NOFDM is modulated using two-dimensional constellation (e.g., M-QAM), while, as Fig. 1 depicts, FrCT-NOFDM is modulated using one-dimensional constellation (e.g., M-PAM). The ID algorithm for FrCT-NOFDM with one-dimensional constellation can been given by
where R is an N-dimensional vector of the received symbol demodulated by FrCT, S i is an N-dimensional vector of the recovered symbol after i th iteration, and e is an N × N identity matrix.
The mapping strategy of 2-PAM constellation is outlined by Fig. 5. Only points that fall in the blue area can be mapped to the corresponding constellation points. The points that fall in the uncertainty interval, which is from −d to d (i.e., the pink area), are unchanged. The d is equal to 1 − i/I where i denotes the i th iteration and I is the total iterative number. In each iteration, the operation of Equation (13) is implemented to eliminate the ICI. As a result, ICI is gradually reduced after each iteration and thus the pink area can be decreased. The algorithm terminates when d is equal to zero. Since the decision for one-dimensional constellation is more simple than that for two-dimensional constellation, ID algorithm of FrCT-NOFDM has lower computational complexity than that of FrFT-NOFDM.
Figure 6 depicts the BER against E b /N 0 for DCT-OFDM (i.e., α = 1) and FrCT-NOFDM. The modulated constellation employs 2-PAM. I denotes the iterative number of ID algorithm. When α is less than 1, the BER performance of FrCT-NOFDM without ID algorithm (i.e., I is set to 0) is seriously influenced by ICI. When I is set to 20, FrCT-NOFDM with α of 0.9 has the same BER performance compared to the DCT-OFDM. This is because that ID algorithm can effectively eliminate the ICI in FrCT-NOFDM with α of 0.9. When α is set to 0.8 or 0.7, the BER performance is still influenced by the residual ICI although the ID algorithm is employed. At the 7% forward error correction (FEC) limit, the required E b /N 0 for FrCT-NOFDM with α of 0.8 is about 2 dB higher than that for DCT-OFDM. If the FEC coding technique is employed, FrCT-NOFDM with α of 0.8 would have almost the same performance with DCT-OFDM. When α is set to 0.7, the BER of FrCT-NOFDM only achieves the 7% FEC limit. The BER performance degrades with the decrease of α due to the increase of residual ICI.
Figure 7 reveals BER versus E b /N 0 for FrCT-NOFDM and FrHT-NOFDM with different subcarrier spacing. The iterative number of ID algorithm is set to 20. The subcarrier spacing is equal to 45%, 40% and 35% of the symbol rate per subcarrier when α in FrCT-NOFDM is set to 0.9, 0.8 and 0.7, respectively and α in FrHT-NOFDM is set to 0.45, 0.4 and 0.35, respectively. As discussed above, the ICI in FrCT-NOFDM should be smaller than that in FrHT-NOFDM. After ID algorithm, the residual ICI in FrCT-NOFDM is also smaller than that in FrHT-NOFDM. Therefore, the BER performance of FrCT-NOFDM is much better than that of FrHT-NOFDM. When the subcarrier spacing is set to 45% of symbol rate per subcarrier, the BER of FrCT-NOFDM descends with the increase of E b /N 0, but the BER of FrHT-NOFDM no longer decreases because the residual ICI begins to be the major distortion when the E b /N 0 is larger than 10 dB. For generating FTN NOFDM signal, FrCT is a much better choice than FrHT.
Figure 8 shows the BER against iterative number of ID algorithm for FrCT-NOFDM when E b /N 0 is set to 20 dB. When α is set to 0.8, BER performance can be improved by the increase of iterative number. Therefore, it has the potential to further eliminate the ICI in FrCT-NOFDM with α of 0.8. However, when α is set to 0.7, the increase of iterative number cannot significantly improve the BER performance. This is because the ICI is too large to be completely eliminated by ID algorithm. Therefore, it needs a more effective algorithm to compensate the interference. The ID-fixed sphere decoder (ID-FSD) algorithm has a better performance than ID algorithm, which combines the ID and FSD algorithms15. Furthermore, the channel coding is effective for resisting the ICI and has been investigated for improving the BER performance of NOFDM7, 24.
The simulation results verify the feasibility of the FrCT-NOFDM. When α is larger than a certain value (this value may be no more than 0.8), ICI can be effectively eliminated and FrCT-NOFDM can achieve almost the same BER performance compared to DCT-OFDM. This certain value is similar to the Mazo limit for FTN-NOTDM systems6. Therefore, when the α is greater than this certain value, the capacity of FrCT-NOFDM has the possibility to approach to the capacity limit.
Proof-of-concept experiment
To verify the feasibility of the FrCT-NOFDM, we set up an experiment as shown in Fig. 1. At the transmitter end, the size of FrCT was set to 256 and 2-PAM was modulated. Sixteen cyclic prefix samples were employed. One frame included 128 FrCT-NOFDM symbols, 10 training symbols and 1 synchronization symbol. The digital signal was uploaded into an arbitrary waveform generator (Tektronix AWG7122C) operating at 10 GS/s to realize digital-to-analog conversion. The resolution of arbitrary waveform generator was set to 8 bits. The overall link rate was 10 Gbit/s and the net bit rate was approximately 8.7 Gbit/s (1 bit/sample × 10 GS/s × 256/(256 + 16) × 128/(128 + 10 + 1) ≈ 8.7 Gbit/s). An external cavity laser (ECL) with a linewidth of 100 kHz was used to generate the optical carrier. A Mach-Zehnder modulator (MZM) was used to modulate the optical carrier with the generated electrical signal. The V π of the MZM is about 1.5 V and the bias voltage is set to about 1.5 V.
The launch optical power was set to 3 dBm. The length of standard signal mode fiber (SSMF) was 50 km. Its total loss was approximately 10 dB. A variable optical attenuator was employed to change the received optical power.
At the receiver end, the received optical signal can be converted into an electrical signal by the photodiode (Discovery DSC-R401HG). The electrical signal was then filtered by a low-pass filter with a 3-dB bandwidth of 10 GHz. The filtered electrical signal was captured by a real-time digital phosphor oscilloscope (Tektronix DPO72004C) operating at 50 GS/s to implement analog-to-digital conversion. The generated digital signal was decoded by off-line processing in MATLAB. The training symbols were used to estimate the channel characteristics for intra-symbol frequency-domain averaging (ISFA) algorithm and frequency-domain equalization25. After equalization, ID algorithm was employed to reduce the ICI.
Figure 9 shows the electrical spectra of DCT-OFDM (i.e., α = 1) and FrCT-NOFDM signal. The baseband bandwidth of DCT-OFDM is equal to 5 GHz which is the Nyquist frequency of the signal with a 10-GS/s sample rate. In FrCT-NOFDM, the baseband bandwidth is compressed to 4.5, 4 and 3.5 GHz and the corresponding Nyquist rate is 9, 8 and 7 Gbit/s when α is set to 0.9, 0.8 and 0.7, respectively. In the experiment, the link rate of FrCT-NOFDM is 10 Gbit/s, which is faster than the corresponding Nyquist rate. Therefore, the FrCT-NOFDM signal is a kind of FTN signal. When α is set to 0.8, 20% baseband bandwidth saving can be obtained and the transmission rate is about 25% faster than the Nyquist rate. These results verify the above theory analysis.
Figure 10 depicts the BER curves for DCT-OFDM (i.e., α = 1) and FrCT-NOFDM after back-to-back (BTB) and 50-km SSMF transmission. The iterative number of the ID algorithm is set to 20. FrCT-NOFDM with α of 0.9 has the same BER performance with DCT-OFDM. After 50-km SSMF transmission, the required received power at the 7% FEC limit was measured to be approximately −12 dBm for FrCT-NOFDM with α of 0.9. Compared to BTB transmission, the power penalty for 50-km SSMF transmission is about 3 dB. When α is set to 0.8, the ICI degrades the BER performance. After 50-km SSMF transmission, the required received power at the 7% FEC limit was measured to be approximately −10 dBm for FrCT-NOFDM with α of 0.8. Compared to DCT-OFDM, the power penalty for FrCT-NOFDM with α of 0.8 is about 2 dB at the 7% FEC limit. When α is set to 0.7, the ICI severely degrades the BER performance, the BER can only achieve the 20% FEC limit.
Figure 11 depicts the BER against iterative number of the ID algorithm after 50-km SSMF transmission. The received power is set to −8 dBm. The α is set to 0.8 and 0.7, respectively. In theory, ID algorithm with more iterative number can eliminate more ICI. Therefore, the BER decreases with the increase of iterative number. However, when iterative number is larger than 20, the increase of iterative number cannot significantly improve the BER performance. This may be because the other distortions such as chromatic dispersion (CD) mainly influence the BER performance when the ICI is small. The experiment results agree well with the simulation results. The feasibility of FrCT-NOFDM has been verified by both the experiment and simulation.
Discussion
The history of FTN signal began with the paper of James Mazo in ref. 6, who investigated the time-domain binary sinc-pulse scheme. The FTN binary sinc-pulse scheme compresses the time period to obtain the transmission rate faster than Nyquist rate. The pulses are accelerated with the time acceleration factor τ and become no longer non-orthogonal, thus the FTN sinc-pulse signal can be considered as a kind of FTN NOTDM signal. Twenty-five percent more bits can be carried in the same bandwidth while τ is set to 0.8, now known as the Mazo limit. In this paper, we demonstrate the principle of FTN NOFDM by taking FrCT-NOFDM for instance. The subcarrier spacing is less than 50% of the symbol rate per subcarrier. When the bandwidth compression factor α is set to 0.8, the subcarrier spacing is equal to 40% of the symbol rate per subcarrier, thus 20% baseband bandwidth saving can be obtained and the transmission rate is about 25% faster than the Nyquist rate.
In 1940s, Shannon put forward the up limit of communication capacity for the Nyquist signal1, 2. When the ISI is effectively compensated, the FTN NOTDM signal can achieve a higher capacity limit than Nyquist signal7, 26. To the best of our knowledge, we first give the mathematical expression for capacity limit of FTN NOFDM signal,
The capacity limit of FTN NOFDM signal is potentially higher than that of Nyquist signal when ICI is effectively compensated. In other word, the capacity of FTN-NOFDM signal is likely to approach the limit only when ICI has been effectively eliminated. Therefore, how to eliminate the ICI is crucial for FTN-NOFDM.
As verified in literatures6, 7, when the α is set to the value between 1 and 0.8, there is not obvious deterioration in BER performance by employing the optimal detection to compensate the interference. In this paper, we demonstrate the simulations and experiments of FrCT-NOFDM system, which verify that ICI can be effectively eliminated when the α is set to the value between 1 and 0.8. As a result, the capacity limit of FrCT-NOFDM signal is potentially higher than that of the Nyquist signal when the α is set to the value between 1 and 0.8. In the further work, more effective algorithm can be employed to eliminate the ICI and higher-order M
Algorithm 1 ID algorithm for 2-PAM constellation. | ||
Input: Received symbol: R; Compression factor: α; Iterative number: I | ||
Output: Recovered symbol: S | ||
1: | for l = 0; l < N; l++ do | \(\vartriangleright\)Calculating correlation matrix C |
2: | for m = 0; m < N; m++ do | |
3: | \({C}_{l\mathrm{,\ }m}=\frac{2}{N}{\sum }_{n=0}^{N-1}\,{W}_{l}\,\cos (\frac{\alpha \pi l\mathrm{(2}n+\mathrm{1)}}{2N})\cdot {W}_{m}\,\cos (\frac{\alpha \pi \mathrm{(2}n+\mathrm{1)}m}{2N})\). | |
4: | end for | |
5: | end for | |
6: | Initialization: S 0 = 0, d = 1 | \(\vartriangleright\)Iterative operation |
7: | for i = 1; i ≤ I; i++ do | |
8: | S i = R−(C−e)S i−1 | |
9: | if S i > d then | \(\vartriangleright\)Constellation mapping |
10: | S i = 1 | |
11: | else if S i < −d then | |
12: | S i = −1 | |
13: | else | |
14: | S i = S i | |
15: | end if | |
16: | d = 1−i/I | \(\vartriangleright \)Updating d |
17: | end for | |
18: | S = S I | |
19: | Return S |
-PAM constellation can be investigated to obtain higher spectral efficiency. FrCT-NOFDM can be potentially used in next-generation high-capacity wireless and optical communications.
Methods
The simulations and off-line processing in the experiment were both implemented by MATLAB. The encoding and decoding were shown in Fig. 1. In the simulation, the AWGN channel was employed. The channel equalization is not required for the AWGN channel. In the experiment, the training symbols were used to estimate the channel characteristics. Meanwhile, the ISFA algorithm can improve the performance of channel estimation25. The frequency-domain equalization can compensate the channel distortion by using the estimated channel characteristics.
In NOFDM system, ID algorithm is employed to eliminate the ICI, which is critical to improve the BER performance. The ID algorithm for 2-PAM constellation is shown in Algorithm 1. Compared to two-dimensional constellation (i.e., M-QAM), the constellation mapping in ID algorithm for one-dimensional constellation (i.e., M-PAM) is more simple and accurate.
References
Shannon, C. E. A mathematical theory of communication. The Bell System Technical Journal 27, 379–423 (1948).
Shannon, C. E. Communication in the presence of noise. Proceedings of the IRE 37, 10–21 (1949).
Essiambre, R. J. et al. Capacity limits of optical fiber networks. J. Lightwave Technol. 28, 662–701 (2010).
Essiambre, R. J. & Robert, W. T. Capacity trends and limits of optical communication networks. Proceedings of the IEEE 100, 1035–1055 (2012).
Liu, X. et al. Phase-conjugated twin waves for communication beyond the Kerr nonlinearity limit. Nature Photonics 7, 560–568 (2013).
Mazo, J. E. Faster-than-nyquist signaling. The Bell System Technical Journal 54, 1451–1462 (1975).
Anderson, J. B., Rusek, F. & Viktor, O. Faster-than-nyquist signaling. Proceedings of the IEEE 101, 1817–1830 (2013).
Andrews, J. G. et al. What Will 5G Be? IEEE Journal on Selected Areas in Communications 32, 1065–1082 (2014).
Zhang, J., Yu, J. & Chi, N. Transmission and full-band coherent detection of polarization multiplexed all-optical Nyquist signals generated by Sinc-shaped Nyquist pulses. Scientific Reports 5, 13649 (2015).
Kaneda, N., Pfau, T. & Lee, J. Frequency Diversity MIMO Detection in Polarization Multiplexed Coherent Optical Transmission. OptoElectronics and Communication Conference and Australian Conference on Optical Fibre Technology (OECC/ACOFT) (Melbourne, Australia), paper TH12E-3 (July. 6th, 2014).
Sato, M. et al. Frequency diversity MIMO detection for dual carrier DP-16QAM transmission. European Conference on Optical Communication (ECOC) (Cannes, France), paper Th.2.5.1 (Sept. 21th, 2014).
Igarashi, K., Tsuritani, T. & Morita, I. Bit-error rate performance of super-Nyquist-WDM DP-QPSK signals with duobinary-pulse shaping. Optical Fiber Communication Conference (OFC) (San Francisco, California, USA), paper Th2A.18 (Mar. 9th, 2014).
Zhang, J. et al. Transmission of single-carrier 400G signals (515.2-Gb/s) based on 128.8-GBaud PDM QPSK over 10,130- and 6,078 km terrestrial fiber links. Opt. Express 23, 16540–16545 (2015).
Zhou, J. et al. Faster-than-Nyquist non-orthogonal frequency-division multiplexing based on fractional Hartley transform. Optics Letters 41, 4488–4491 (2016).
Xu, T. et al. An Improved Fixed Sphere Decoder Employing Soft Decision for the Detection of Non-orthogonal Signals. IEEE Commun. Lett. 17, 1964–1967 (2013).
Darwazeh, I. et al. Optical SEFDM System; Bandwidth Saving Using Non-Orthogonal Sub-Carriers. IEEE Photonic. Tech. Lett. 26, 352–355 (2014).
Nopchinda, D. et al. Dual Polarization Coherent Optical Spectrally Efficient Frequency Division Multiplexing. IEEE Photonic. Tech. Lett. 28, 83–86 (2016).
Ahmed, N., Natarajan., T. & Rao, K. R. Discrete cosine transform. IEEE Tran. computers C-23, 90–93 (1974).
Zhou, J., Qiao, Y. J., Cai, Z. & Ji, Y. F. Asymmetrically Clipped Optical Fast OFDM Based on Discrete Cosine Transform for IM/DD Systems. J. Lightwave Technol. 33, 1920–1927 (2015).
Zhou, J. et al. FOFDM Based on Discrete Cosine Transform for Intensity-Modulated and Direct-Detected Systems. J. Lightwave Technol. 34, 3717–3725 (2016).
Tan, P. & Beaulieu, N. C. A Comparison of DCT-Based OFDM and DFT-Based OFDM in Frequency Offset and Fading Channels. IEEE Trans. Commun. 54, 2113–2125 (2006).
Zhao, J. & Ellis, A. D. A Novel Optical Fast OFDM with Reduced Channel Spacing Equal to Half of the Symbol Rate Per Carrier. Optical Fiber Communication Conference (OFC) (San Diego, California, USA), paper OMR1 (Mar. 21th, 2010).
Sommerville, D. M. Y. An Introducation to the Geometry of N Dimensions (METHUEN & CO. LTD, 1929).
Xu, T. et al. A Soft Detector for Spectrally Efficient Systems with Non-Orthogonal Overlapped Sub-Carriers. IEEE Commun. Lett. 18, 1847–1850 (2014).
Liu, X. & Buchali, F. Intra-symbol frequency-domain averaging based channel estimation for coherent optical OFDM. Opt. Express 16, 21944–21957 (2008).
Rusek, F. & Anderson, J. B. Constrained Capacities for Faster-Than-Nyquist Signaling. IEEE Trans. Inf. Theory 55, 764–775 (2009).
Acknowledgements
This work was supported in part by National Natural Science Foundation of China (61427813, 61331010, 61271192); BUPT Excellent Ph.D. Students Foundation; China Scholarship Council Foundation.
Author information
Authors and Affiliations
Contributions
J.Z. and Y.Q. derived the theoretical results, J.Z. and Y.Q. conceived the simulation and experiment, J.Z., M.G., and X.T. conducted the simulation and experiment, J.Z., Z.Y., Q.C., and Q.W. analyzed the results. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhou, J., Qiao, Y., Yang, Z. et al. Capacity limit for faster-than-Nyquist non-orthogonal frequency-division multiplexing signaling. Sci Rep 7, 3380 (2017). https://doi.org/10.1038/s41598-017-03571-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-017-03571-6
- Springer Nature Limited
This article is cited by
-
Experimental comparison of 28 Gb/s NRZ and EDB schemes for faster-than-Nyquist PON
Optical and Quantum Electronics (2018)