Abstract
The lithium niobate on insulator (LNOI) platform has revolutionized lithium niobate materials, and a series of quantum photonic chips have exhibited unprecedented performances. Quantum frequency conversion (QFC) that enables quantum state preservation during frequency conversion is crucial in quantum technology. This work demonstrates a low-noise QFC process on the LNOI nanophotonic platform, connecting telecom and near-visible bands. An internal conversion efficiency of 73% and an on-chip noise count of 900 counts per second (cps) are achieved. Furthermore, the preservation of quantum statistical properties is verified, indicating the QFC chip’s promise for extensive applications of LNOI integrated circuits in quantum information. Based on this chip, we constructed an upconversion single-photon detector with a detection efficiency of 8.7% and a noise of 300 cps, paving the way to integrated on-chip single-photon detection. The realization of a low-noise QFC device also provide a pathway for practical chip-scale QFC-based quantum systems in heterogeneous configurations.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
Photonic integrated chips with multiple optical operations have been extensively studied in the last decade for quantum information1,2,3,4. Among semiconductor-on-insulator platforms, including silicon5, GaAs6,7, lithium niobate8,9, and others10,11,12, lithium niobate on insulator (LNOI) is considered a promising integrated platform owing to its wide transparency window (350–4500 nm), outstanding electro-optic property, large optical nonlinearity efficiency, flexible ferroelectric domain control, and feasible heterogeneous integration with silicon13,14,15, NbN16 and Si3N417, and so on18. As one of the building blocks for a quantum photonic circuit based on LNOI, the frequency converter has been investigated for its extremely high conversion efficiency owing to its strong optical confinement and state-of-the-art fabrication technology19,20,21. In chip-scale quantum information applications, a low-noise quantum frequency converter on LNOI is of the essence while unexplored thus far.
Quantum frequency conversion (QFC) has found extensive applications in quantum information research, including single-photon detectors22,23,24, interfaces between long-distance quantum memories and various quantum systems25,26,27,28,29, and photon-color erasers30,31. In these previous demonstrations, efficient quantum frequency converters were implemented with periodically poled lithium niobate (PPLN) waveguides with optical mode dimensions of several microns using ridge waveguides32 or diffused waveguides fabricated by proton exchange26,33 or titanium indiffusion34. The noise distribution of QFC pumped with telecom-band laser has been studied on periodically poled LNOI nanophotonic chip35. The employed sum-frequency generation (SFG) process induced an insufferable noise count rate (NCR) at the Mcps level mainly due to remarkable spontaneous Raman scattering (SRS). Generally, ultra-high noise will destroy the quantum state and make it difficult to achieve QFC at the single-photon level.
In this work, we design and fabricate a low-noise QFC nanophotonic waveguide on an LNOI chip. The telecom-band single photons are upconverted to the near-visible band by pumping with a 1950 nm single-frequency laser. An internal conversion efficiency of 73% and an on-chip NCR of 900 cps are achieved. Comparing the second-order correlation properties of the telecom-band heralded single-photon source (HSPS) before and after the QFC, the quantum state preservation on the LNOI platform is verified. Such a QFC chip is promising for the extensive applications of LNOI integrated circuits in quantum information. With the sum-frequency output spectrally filtered and detected by a silicon single-photon avalanche photodiode (SPAD), we construct an upconversion single-photon detector (SPD) showing an average detection efficiency (DE) of 8.7% and an NCR of 300 cps, which demonstrates the feasibility of an LNOI-chip-based upconversion SPD.
Results
Chip design and fabrication
In this part, the QFC chip is designed and fabricated to realize frequency upconversion between the 1550 nm band (signal) and the 860 nm band (sum-frequency) with a single-frequency pump laser fixed at 1950 nm as shown in Fig. 1a. The device is fabricated on a Z-cut lithium niobate thin film bonded to a 2-µm thick thermally grown silicon dioxide layer on a silicon substrate (NANOLN Inc.). To utilize the maximum nonlinear coefficient of lithium niobate, which is d33~27 pm/V, both the signal light and the pump light are expected to propagate in the TM mode along the x-axis. In Z-cut LNOI, two kinds of undesirable conditions can easily occur if the waveguide parameters are designed improperly, especially in our device where the three mixing lasers cover a wide wavelength span. The first is lateral leakage, attributed to the effective refractive index of the mode in the rib waveguide being lower than that in the slab, leading to the radiation of the guided mode in the shallow rib waveguide into orthogonally polarized slab modes36, resulting in high propagation loss of the signal. As an example, the simulated mode field distribution is shown in Fig. 1b with an LN thickness of 800 nm, ridge height of 351.5 nm, and top width of 1.8 μm at 1550 nm. Generally, it can be prevented by increasing the ridge height for an LNOI film of a given thickness.
The second is the existence of special modes called “hybrid modes” caused by asymmetry of the structural refractive index distribution, which is closely related to waveguide parameters37. As an example, the profiles of two adjacent modes at 1950 nm are shown in Fig. 1c, both of which are hybrid modes with an LN thickness of 800 nm, ridge height of 450 nm, and top width of 1.5 μm. Among these pump laser modes, the nondominant field components take a non-negligible proportion, and their power even equals the dominant field, which will greatly reduce the overlap integral of the three interacting waves. The simulation results show that when the ridge height exceeds a certain depth and gradually increases toward the film thickness, the TE polarization fraction defined by \({\textstyle{{{\int} {{\int} {|E_{{{\mathrm{y}}}}|^2{{{\mathrm{dydz}}}}} } } \over {{\int} {{\int} {(|E_{{{\mathrm{z}}}}|^2 + |E_{{{\mathrm{y}}}}|^2){{{\mathrm{dydz}}}}} } }}}\) of the pump, quasi-TM mode tends to increase, while that of the sum-frequency (SF) quasi-TM mode tends to decrease. This unfavorable trade-off between the short wave and long wave limits the mode-overlap integral for three-wave interactions, which is closely related to the normalized nonlinear efficiency.
The effects of lateral leakage and hybrid modes can be greatly reduced by carefully selecting the waveguide parameters. Finally, we choose an LN thickness of 800 nm, a ridge height of 422 nm, and a top width of 1.8 μm, and correspondingly, the quasi-phase-matching period is 4.1 μm. The simulated theoretical normalized conversion efficiency reaches 3552%W−1 ∙ cm−2 due to the optimized large mode-overlap integral and tight light confinement, although there is still a small amount of TE components in the quasi-TM modes for the SF and pump. The modes of the signal, pump, and SF are shown in Fig. 1d.
The scanning electron microscopy image of the fabricated waveguide with the selected parameters is shown in the inset of Fig. 1a. The ripples on the surface of the slab are caused by selective etching, while the sidewall and upper surface of the waveguide are protected well. The length of the waveguide is 5.3 mm, and both facets are polished by chemical mechanical polishing.
Frequency conversion efficiency of the chip
The typical phase-matching curve and conversion efficiencies of our device are presented in Fig. 2. The SFG tuning curve of the waveguide is measured by sweeping the signal wavelength from 1500 nm to 1560 nm with the pump wavelength fixed at 1950 nm. As shown in Fig. 2b, the phase-matching signal wavelength is 1531.1 nm at room temperature at ~18 °C with a full width at half maximum (FWHM) of 10.5 nm. A 1 K temperature variation can detune the phase-matching wavelength by ~1 nm. The oscillation of the curve is caused by F-P interference between the two facets, which can be eliminated by the AR coating. The imperfection of the tuning curve is primarily due to the inhomogeneities in the waveguide and film, as well as the imperfect poling. According to our simulation, a 1 nm variation in waveguide width can cause a detuning of ~4 nm in the phase-matching wavelength, a 1 nm variation in film thickness can lead to a detuning of ~27 nm in the phase-matching wavelength, and a 1 nm variation in polarization period can result in a detuning of ~4 nm in the phase-matching wavelength.
The conversion efficiencies versus pumping power measured at the output port are shown in Fig. 2c. The conversion efficiency is fitted with the model38
where ηmax is the maximum efficiency, which is less than 1 due to propagation loss, P is the pump power at the output facet, ηnor is the normalized conversion efficiency, and L is the quasi-phase-matching length of the waveguide. The highest internal conversion efficiency is ~73% when the pump power on-chip is ~310 mW according to the fitting result, and the calculated normalized efficiency is (2837 ± 97)%W−1 ∙ cm−2, which is ~80% of the theoretical value of 3552%W−1 ∙ cm−2. Subjected to the pump power limitation and reduced system stability caused by high pump power, the signal depletion with a pump power of 246 mW is measured to be 14.8 dB (96.7%) by coupling the output signal into an optical spectrum analyzer and comparing the observed signal levels with the pump on and off38. The required pump power can be further reduced by increasing the waveguide length.
Frequency conversion noise analysis
The possible noise mechanisms caused by pump laser include second harmonic generation (SHG), third harmonic generation (THG), SRS noise in fiber, SRS noise at the signal band in the waveguide, second harmonic generation-spontaneous parametric down-conversion (SHG-SPDC) noise at signal band, SHG-SRS noise at SF band, and spontaneous four-wave mixing (SFWM) noise. The SHG and THG noises can be easily removed by commercial filters, while the other noises are indistinguishable from signal or SF photons, as depicted in Fig. 3a. The main noise source in our device is the SHG-SPDC process, especially for the high conversion efficiency condition with high power pumping. The SHG-SPDC photons that fall into the bandwidth of the QFC are upconverted to the SF band, causing noise performance deterioration.
The measurement setup used to characterize the noise performance of the QFC chip is shown in Fig. 2a. The SF light is separated from the pump and non-converted signal with a longpass dichroic mirror, then cleaned further with a series of filters and detected by a SPAD finally (for more details see “Methods”). Taking into account the free space transmission efficiency of the noise photons, we show the total on-chip NCR dependence on the pump power in Fig. 3b. The inset curve with the total on-chip NCR and pump power both in the logarithmic coordinates demonstrates a slope of ~2.3 at pump power of 240 mW, showing that the total noise increases cubically with pump power in the high conversion efficiency region approximatively. This is consistent with the case mentioned above, in which the dominating noise generation process is SHG-SPDC, which has a nearly cubic dependency on the pump power.
We further quantify the noise count from the SHG-SPDC process without other noise interference by directly importing the 975 nm light generated by a homemade 1950-nm SHG PPLN waveguide to the QFC chip. Since we directly import the SH to the QFC chip, there is a coefficient of 1/2 between the noise generated by the SHG-SPDC process and the measured noise count here. More details of the measurements are presented in the supplementary method. The SHG-SPDC noise count in the SF band versus the pump power is also plotted in Fig. 3b. The proportion of SPDC noise to the total noise gradually increases as pump power gets stronger and reaches 77% for a pump power of ~268 mW, corresponding to an internal conversion efficiency of ~72%. The remaining nondominant noise can be attributed to the other noise sources, including several SRS processes and the SFWM process, which cannot be characterized separately. The SRS noises directly generated by the strong pump field in the signal band are greatly suppressed both in the fiber and waveguide because the pump laser used is largely detuned with the signal22,32,39. The SHG-SPDC noise can be further reduced through the optimization of periodic polarization quality. The SRS noise can be reduced further by lowering the working temperature and increasing the waveguide length, correspondingly reducing the required pump power.
QFC of heralded single-photon source
It is generally assumed that the quantum state is preserved during the mixing process in a periodically poled LNOI nanophotonic waveguide, such as that in the conventional micron waveguide32,40. However, this has to be verified experimentally, since the effective refractive index and the mode profile that may affect the nonlinear process are quite different in the two platforms. Here, the non-classical intensity correlation, one quantum property of a heralded single-photon source, is selected to verify the QFC performance32.
We use another homemade PPLN waveguide to generate SPDC photon pairs with signal photons at the 1530-nm band and idler photons at the 1591-nm band pumped with a 780-nm CW laser, which is filtered after exiting the PPLN waveguide. The signal photons and the idler photons are separated by DWDM centered at 1530 nm, and the idler arm is filtered by a tunable filter centered at 1591 nm, as shown in Fig. 4.
First, we measured the normalized second-order cross-correlation function to describe the statistical properties of the SPDC photon pairs in Fig. 4a with \(g_{{{{\mathrm{si}}}}}^{\left( 2 \right)}\left( \tau \right) = {\textstyle{{N_{{{{\mathrm{s}}}},{{{\mathrm{i}}}}}} \over {N_{{{\mathrm{s}}}}\cdot N_{{{\mathrm{i}}}}\cdot \tau _{{{\mathrm{b}}}}}}}\)41, where \(N_{{{{\mathrm{s}}}},{{{\mathrm{i}}}}},N_{{{\mathrm{s}}}}(N_{{{\mathrm{i}}}})\) are the coincidence count rate and channel count rate of the signal and idler photons, and τb is the coincidence time window. Considering the coherence time, time jitter of the detector, and temporal resolution of the detector, we use a coincidence time window of 1500 ps and obtain \(g_{{{{\mathrm{si}}}}}^{(2)}(0) = 22\), showing a strong correlation well above the classical thermal statistic threshold of 2. Next, the heralded single-photon property is characterized with the idler photons played as the heralding photons, as shown in Fig. 4b. The signal photons are split by a 50/50 beam splitter and sent to two separate channels of SNSPD. We measured the heralded self-correlation function42
For the special case, we are interested in where \(g_{{{\mathrm{H}}}}^{(2)}(\tau ) \equiv g_{{{\mathrm{H}}}}^{(2)}(0,\tau |0)\). \(N_{{{{\mathrm{s}}}}1{{{\mathrm{i}}}}}(N_{{{{\mathrm{s}}}}2{{{\mathrm{i}}}}})\) is the double coincident count rate of the idler and signal 1 (signal 2). Nssi is the triple signal-signal-idler coincidence rate, and Ni is the count rate of the idler arm. Figure 5a shows that the lowest self-correlation value at zero delays is \(g_{{{\mathrm{H}}}}^{(2)}(0) = 0.14\) with a coincidence time window of 1500 ps, showing strong antibunching behavior. Finally, the 1530-nm band signal photons are upconverted to the 857-nm band by our LNOI chip, and the self-correlation function is measured with the idler photons as herald shown in Fig. 4c. The measured self-correlation function shown in Fig. 5b is \(g_{{{\mathrm{H}}}}^{(2)}(0) = 0.23\), which is higher than that of the photon-pair source due to the noise counts introduced by the nonlinear process. However, \(g_{{{\mathrm{H}}}}^{(2)}(0)\) is still below the classical threshold of 0.5, proving that the single-photon nature is preserved after the frequency conversion process.
Upconversion SPD
Here, we construct an upconversion single-photon detection based on the QFC chip. In Fig. 2a, the signal source is replaced by a single-photon source of one million photons centered at 1531 nm consisting of two variable optical attenuators (VOAs) and a 99/1 beam splitter33. The filtering system and SPAD are all the same as the noise measurement setup in Fig. 2. The pump power is tuned, and the upconversion SPD system DE and NCR at different pump powers are recorded and depicted in Fig. 6. System DE is obtained by dividing the number of detected count rates after NCR subtraction by one million, which is the signal photon count rate before entering the WDM.
A system DE of 8.7% and an NCR of 300 cps are achieved at a pump power of ~240 mW on the chip, which shows preliminary practicality. The NEP of the upconversion single-photon detector is calculated about 3.65 × 10−17 \({{{\mathrm{W}}}} \cdot {{{\mathrm{Hz}}}}^{ - {\textstyle{1 \over 2}}}\) by the formula \({{{\mathrm{NEP}}}} = {\textstyle{{{{{\mathrm{h}}}}\upsilon \cdot \sqrt {2{{{\mathrm{NCR}}}}} } \over {{{{\mathrm{DE}}}}}}}\), where hυ is the energy of signal photon, NCR is the noise count rate, DE is the detection efficiency. The pump power can be significantly reduced by increasing the length of the chip, and consequently, the noise count would be notably depressed due to the near cubically dependent relationship. The unsatisfactory DE performance is caused by the insertion losses and efficiencies of the components, which are listed in Table 1. The major loss is a fiber-to-chip coupling loss of ~4 dB, which severely affects system performance. To reduce the coupling loss, some inverted taper designs have been proposed and experimentally realized with a coupling loss of less than 0.5 dB43,44. Another non-negligible loss is the relatively low internal conversion efficiency mainly due to the transmission loss, which can be further reduced to less than 0.1 dB/cm by optimizing the fabrication process45. Moreover, the loss of the free space filtering module could also be further optimized. After the improvements mentioned above, a highly practical upconversion SPD with a DE of ~30% could be achieved.
Discussion
In addition to the upconversion SPD, the low-noise high-efficiency on-chip frequency conversion provides possibilities for integrated QFC-based quantum systems through heterogeneous integration with other materials. Generally, a fully scalable quantum photonic chip should realize both quantum state manipulation and single-photon detection on a monolithic chip where the QFC could play crucial roles. As an important quantum state manipulation, low-noise QFC has been achieved on our LNOI chip, which could realize interfaces between long-distance quantum memories and various quantum systems. Critical but difficult, on-chip single-photon detection still needs to be explored. The integration of superconducting nanowires with LNOI has been proposed to realize single-photon detection on the telecom band16,18, while the ultralow temperature refrigeration system may be cumbersome for some applications. Another alternative for on-chip low-noise single-photon detection is to combine an antimonide semiconductor laser as a pump laser and SPAD as an SF detector with an LNOI QFC chip by heterogeneous integration, which only requires compact temperature control.
In conclusion, we have achieved quantum frequency conversion in the LNOI nanophotonic platform with an internal conversion efficiency of 73% and a noise count rate of 900 cps on-chip. We verified the preservation of the quantum state after the QFC process by using the non-classical intensity correlation of a heralded single-photon source as the input quantum property, which is the first verification in the LNOI platform to the best of our knowledge. Moreover, an upconversion single-photon detector in the telecom band with a system DE of 8.7% and NCR of 300 cps is developed based on the QFC chip. The on-chip low-noise and high-efficiency quantum frequency converter indicates the possibilities of chip-scale QFC-based systems in heterogeneous configurations.
Methods
Chip fabrication
To fabricate the nanophotonic chip, we first pattern the poling electrodes on the surface of the lithium niobate thin film using UV lithography and wet etching. Then, several 800 V pulses with a duration of tens of seconds are applied to achieve periodic domain inversion with a duty cycle of ~50%. After periodic poling, the electrodes are removed, and the waveguide is patterned by electron-beam lithography (EBL) following an Ar-based dry etching process to form a ridge waveguide45. An optimized RCA cleaning process is applied to remove the redeposition created in the dry etching process and reduce the selective etching to periodical domains.
Measurement setup
The measurement setup is depicted in Fig. 2a. A homemade 1950 nm single-frequency laser and the signal light from a continuous-wave telecom tunable laser source (Santec TSL-550, 1480–1630 nm) are coupled into an in-line fiber polarization controller to ensure TM polarization separately. Then, the two beams are combined through a 1550-nm/1950-nm wavelength division multiplexer (WDM) and injected into the nano-waveguide with a lensed fiber (OZ optics). We measured the propagation loss of the PPLNOI waveguide by the Fabry–Perot interference method, which is ~3 dB/cm at the telecom band. The mode field diameter of the lensed fiber is 2.5 ± 0.5 μm, and the coupling loss is estimated to be ~4 dB for the signal wavelength by dual-edged coupling between the waveguide and two lensed fibers. The output from the waveguide is collected by an aspheric lens and collimated into free space.
To characterize the noise performance of the QFC chip, the SF light, pump, and non-converted signal are separated by a longpass dichroic mirror. A 785-nm longpass filter, a 945-nm shortpass filter, an 857-nm bandpass filter with a 30-nm bandwidth, a 0.5-nm narrowband filter centered at 857.6 nm and an etalon with a bandwidth of 0.09 nm, and a free spectral range of 1.5 nm are used to clean the SF further. Then, the SF light is coupled into a multimode fiber and detected by a SPAD with a detection efficiency of ~50% and an intrinsic dark noise of ~60 cps.
Data availability
The data that supports the findings of this study are available from the corresponding author upon reasonable request.
References
Politi, A., Cryan, M. J., Rarity, J. G., Yu, S. & O’Brien, J. L. Silica-on-silicon waveguide quantum circuits. Science 320, 646–649 (2008).
Ladd, T. D. et al. Quantum computers. Nature 464, 45–53 (2010).
Silverstone, J. W. et al. On-chip quantum interference between silicon photon-pair sources. Nat. Photon. 8, 104–108 (2013).
Wang, J., Sciarrino, F., Laing, A. & Thompson, M. G. Integrated photonic quantum technologies. Nat. Photon. 14, 273–284 (2020).
Soref, R. The past, present, and future of silicon photonics. IEEE J. Sel. Top. Quantum Electron. 12, 1678–1687 (2006).
Horn, R. et al. Monolithic source of photon pairs. Phys. Rev. Lett. 108, 153605 (2012).
Kuo, P. S., Bravo-Abad, J. & Solomon, G. S. Second-harmonic generation using \(\bar 4\)-quasi-phasematching in a GaAs whispering-gallery-mode microcavity. Nat. Commun. 5, 3109 (2014).
Wang, C. et al. Integrated lithium niobate electro-optic modulators operating at CMOS-compatible voltages. Nature 562, 101–104 (2018).
Zhang, M. et al. Broadband electro-optic frequency comb generation in a lithium niobate microring resonator. Nature 568, 373–377 (2019).
Moss, D. J., Morandotti, R., Gaeta, A. L. & Lipson, M. New CMOS-compatible platforms based on silicon nitride and Hydex for nonlinear optics. Nat. Photon. 7, 597–607 (2013).
Abellan, C. et al. Quantum entropy source on an InP photonic integrated circuit for random number generation. Optica 3, 989–994 (2016).
Lukin, D. M. et al. 4H-silicon carbide-on-insulator for integrated quantum and nonlinear photonics. Nat. Photon. 14, 330–334 (2020).
Chen, L., Xu, Q., Wood, M. G. & Reano, R. M. Hybrid silicon and lithium niobate electro-optical ring modulator. Optica 1, 112–118 (2014).
He, M. et al. High-performance hybrid silicon and lithium niobate Mach–Zehnder modulators for 100 Gbit s−1 and beyond. Nat. Photon. 13, 359–364 (2019).
Shams-Ansari, A. et al. Electrically pumped laser transmitter integrated on thin-film lithium niobate. Optica 9, 408–411 (2022).
Sayem, A. A., Cheng, R.-S., Wang, S.-H. & Tang, H.-X. Lithium-niobate-oninsulator waveguide-integrated superconducting nanowire single-photon detectors. Appl. Phys. Lett. 116, 151102 (2020).
Pohl, D. et al. An integrated broadband spectrometer on thin-film lithium niobate. Nat. Photon. 14, 24–29 (2020).
Lomonte, E. et al. Single-photon detection and cryogenic reconfigurability in lithium niobate nanophotonic circuits. Nat. Commun. 12, 6847 (2021).
Wang, C. et al. Ultrahigh-efficiency second-harmonic generation in nanophotonic PPLN waveguides. Optica 5, 1438–1441 (2018).
Chen, J.-Y. et al. Ultra-efficient frequency conversion in quasi-phase-matched lithium niobate microrings. Optica 6, 1244–1245 (2019).
Lu, J. et al. Periodically poled thin-film lithium niobate microring resonators with a second-harmonic generation efficiency of 250,000%/W. Optica 6, 1455–1460 (2019).
Pelc, J. S. et al. Long-wavelength-pumped upconversion single-photon detector at 1550 nm: performance and noise analysis. Opt. Express 19, 21445–21456 (2011).
Ma, L., Slattery, O. & Tang, X. Single photon frequency up-conversion and its applications. Phys. Rep. 521, 69 (2012).
Liao, S.-K. et al. Long-distance free-space quantum key distribution in daylight towards inter-satellite communication. Nat. Photon. 11, 509–513 (2017).
Maring, N. et al. Photonic quantum state transfer between a cold atomic gas and a crystal. Nature 551, 485–488 (2017).
Yu, Y. et al. Entanglement of two quantum memories via fibers over dozens of kilometers. Nature 578, 240–245 (2020).
van Leent, T. et al. Long-distance distribution of atom-photon entanglement at telecom wavelength. Phys. Rev. Lett. 124, 010510 (2020).
Luo, X.-Y. et al. Postselected entanglement between two atomic ensembles separated by 12.5 km. Phys. Rev. Lett. 129, 050503 (2022).
van Leent, T. et al. Entangling single atoms over 33 km telecom fibre. Nature 607, 69–73 (2022).
Takesue, H. Erasing distinguishability using quantum frequency up-conversion. Phys. Rev. Lett. 101, 173901 (2008).
Qu, L.-Y. et al. Color erasure detectors enable chromatic interferometry. Phys. Rev. Lett. 123, 243601 (2019).
Maring, N., Lago-Rivera, D., Lenhard, A., Heinze, G. & de Riedmatten, H. Quantum frequency conversion of memory-compatible single photons from 606 nm to the telecom C-band. Optica 5, 507–513 (2018).
Zheng, M.-Y. et al. Integrated multichannel lithium niobate waveguides for quantum frequency conversion. Phys. Rev. Appl. 14, 034035 (2020).
Allgaier, M. et al. Highly efficient frequency conversion with bandwidth compression of quantum light. Nat. Commun. 8, 14288 (2017).
Fan, H. et al. Photon conversion in thin-film lithium niobate nanowaveguides: A noise analysis. J. Opt. Soc. Am. B 38, 2172–2179 (2021).
Boes, A. et al. Improved second harmonic performance in periodically poled LNOI waveguides through engineering of lateral leakage. Opt. Express 27, 23919–23928 (2019).
Kaushalram, A., Hegde, G. & Talabattula, S. Mode hybridization analysis in thin film lithium niobate strip multimode waveguides. Sci. Rep. 10, 16692 (2020).
Roussev, R. V., Langrock, C., Kurz, J. R. & Fejer, M. M. Periodically poled lithium niobate waveguide sum-frequency generator for efficient single-photon detection at communication wavelengths. Opt. Lett. 29, 1518–1520 (2004).
Zaske, S., Lenhard, A. & Becher, C. Efficient frequency down conversion at the single photon level from the red spectral range to the telecommunications C-band. Opt. Express 19, 12825–12836 (2011).
Ikuta, R. et al. Wide-band quantum interface for visible to telecommunication wavelength conversion. Nat. Commun. 2, 537 (2011).
Guo, X. et al. Parametric down-conversion photon-pair source on a nanophotonic chip. Light Sci. Appl. 6, 16249 (2016).
Bettelli, S. Comment on ‘Coherence measures for heralded single-photon sources’. Phys. Rev. A 81, 037801 (2010).
He, L. et al. Low-loss fiber-to-chip interface for lithium niobate photonic integrated circuits. Opt. Lett. 44, 2314–2317 (2019).
Hu, C. et al. High-efficient coupler for thin-film lithium niobate waveguide devices. Opt. Express 29, 5397–5406 (2021).
Zhang, M., Wang, C., Cheng, R., Shams-Ansari, A. & Lončar, M. Monolithic ultra-high-Q lithium niobate microring resonator. Optica 4, 1536–1537 (2017).
Acknowledgements
This work is supported by National Key R&D Program of China (2018YFB0504300, 2017YFA0303902, 2017YFA0304000), National Natural Science Foundation of China (T2125010), Key R&D Plan of Shandong Province (2019JZZY010205), Natural Science Foundation of Shandong Province (ZR2019LLZ003, ZR2020LLZ007, ZR2021LLZ013), the Chinese Academy of Science, the SAICT Experts Program, the Taishan Scholar Program of Shandong Province, Quancheng Industrial Experts Program. The authors thank Daiying Wei for polishing the waveguide.
Author information
Authors and Affiliations
Contributions
Q.Z. and J.-W.P. conceived the research. M.-Y.Z., Q.Z., and J.-W.P. designed the experiment. X.W. designed, fabricated, and tested the device with assistance of X.J., B.W., Y.L., and X.-P.X.. X.W., M.-Y.Z., Q.Z., and J.-W.P. analyzed the data and wrote the paper.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Wang, X., Jiao, X., Wang, B. et al. Quantum frequency conversion and single-photon detection with lithium niobate nanophotonic chips. npj Quantum Inf 9, 38 (2023). https://doi.org/10.1038/s41534-023-00704-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41534-023-00704-w
- Springer Nature Limited