Abstract
Combining superconducting resonators and quantum dots has triggered tremendous progress in quantum information, however, attempts at coupling a resonator to even charge parity spin qubits have resulted only in weak spin-photon coupling. Here, we integrate a zincblende InAs nanowire double quantum dot with strong spin-orbit interaction in a magnetic-field resilient, high-quality resonator. The quantum confinement in the nanowire is achieved using deterministically grown wurtzite tunnel barriers. Our experiments on even charge parity states and at large magnetic fields, allow us to identify the relevant spin states and to measure the spin decoherence rates and spin-photon coupling strengths. We find an anti-crossing between the resonator mode in the single photon limit and a singlet-triplet qubit with a spin-photon coupling strength of g/2π = 139 ± 4 MHz. This coherent coupling exceeds the resonator decay rate κ/2π = 19.8 ± 0.2 MHz and the qubit dephasing rate γ/2π = 116 ± 7 MHz, putting our system in the strong coupling regime.
Similar content being viewed by others
Introduction
Spin qubits in semiconductors are promising candidates for scalable quantum information processing due to long coherence times and fast manipulation1,2,3,4. For the qubit readout, circuit quantum electrodynamics based on superconducting resonators5, allows a direct and fast measurement of qubit states and their dynamics6. Recently, resonators were used to achieve charge–photon7,8, spin–photon9,10,11 as well as coherent coupling of distant charge12 and spin qubits13,14, enabling coherent information exchange between distant qubits. However, the small electric and magnetic moments of individual electrons require complicated device architectures such as micromagnets, and a large number of surface gates that render scaling up to more complex architectures challenging. These approaches typically achieve a relatively weak electron spin–photon coupling on the order of ~10−30 MHz. In addition to single electron spin qubits, also spin qubits based on two electrons in a double quantum dot (DQD), e.g. a singlet–triplet qubit have been demonstrated15. Spin qubits based on two electrons typically offer a large hybridization of the spin and charge degree of freedom compared to single-electron spin qubits in principle allowing even stronger coupling strengths. So far, however, the experimentally achieved coupling strengths in such systems16,17 remained well below the strong coupling limit in which the coherent coupling rate exceeds both, the cavity mode decay rate and the qubit linewidth.
Here, we demonstrate that the strong coupling regime between a singlet–triplet qubit and a single photon in a superconducting resonator can be reached. We achieve this strong coupling by carefully designing the resonator and by using a DQD defined by in-situ grown tunnel barriers in a semiconductor with a large spin–orbit interaction. The tunnel barriers consist of InAs segments in the wurtzite crystal-phase with an atomically sharp interface to the zincblende bulk of the nanowire (NW)18. These crystal-phase barriers are highly reproducible and render the need of barrier gates obsolete, simplifying integration with superconducting resonators and making the nanowires a viable prototype for scalable quantum computing architectures.
In this work, we make use of the large spin–orbit interaction in these nanowires19 to define a singlet–triplet qubit at a finite in-plane magnetic field in which the \({T}_{1,1}^{+}\) and S2,0 states hybridize, forming a quantum two-level system. Incorporating a NW with a magnetic-field resilient resonator based on NbTiN20,21 allows us to measure an avoided crossing between the singlet–triplet qubit and a single-photon excitation of the resonator at a magnetic-field strength of B = 300 mT. The measured coupling strength is very large compared to previously reported electron spin–photon coupling9,10,11, which enables us to reach the strong coupling regime. In addition, by analyzing the response of the hybridized resonator-qubit system for varying magnetic-field strengths, we perform qubit spectroscopy22,23,24. This allows us to identify the specific spin states and to quantitatively extract the relevant device properties.
Results
Device characterization
Details about the NW properties and their growth can be found in the supplementary. The resonator-qubit system of device A is shown in Fig. 1a, including a false-colored SEM-image of the crystal-phase defined NW DQD. We report similar experiments for two devices, A and B, with B discussed in the supplementary. They are measured in a dilution refrigerator with a base temperature of 70 mK. The DQD forms in the 490 and 370 nm long zincblende segments (green), separated by 30 nm long wurtzite (red) tunnel barriers with a conduction band offset of ~100 meV25, as illustrated in Fig. 1b. A high-impedance, half-wave coplanar-waveguide resonator is capacitively coupled to the DQD at its voltage anti-node via a sidegate. In addition, the same sidegate can be used to tune the DQD charge states using a dc voltage (VR) applied at the resonator voltage node. The DQD state is probed by reading out the resonator rf-transmission. We extract the bare resonance frequency of the resonator ω0/2π = 5.1705 ± 0.0003 GHz at zero magnetic field and the bare decay rate κ∣B=0/2π = 27.3 ± 0.6 MHz. The resonator design and fitting are described in detail in the “Methods” section. In the following, we prepare the DQD in an even charge configuration in the many-electron regime (see the “Methods” section), described by a two-electron Hamiltonian given in the “Methods” section. Figure 1c shows the eigenvalues of this Hamiltonian as a function of external magnetic field B at a fixed DQD detuning. At zero magnetic field, the detuning renders the singlet S2,0 the ground state, for which both electrons reside in the same dot. Without spin-rotating tunneling, this, and the S1,1 state, with the electrons distributed to different dots, form a charge qubit26. The subscripts describe the dot electron occupation of the left and right dots, respectively. By applying an external magnetic field, the Zeeman effect lowers the energy of the triplet \({T}_{1,1}^{+}\) state, that becomes the ground state for sufficiently high magnetic fields. In the presence of a spin-rotating tunneling t = ΔSO/2 induced by the intrinsic spin–orbit interaction ΔSO, the energy levels of the hybridized S2,0 and \({T}_{1,1}^{+}\) states are split. The two new eigenstates of the avoided crossing form a singlet–triplet qubit shown schematically in Fig. 1a and b.
Figure 2a shows the charge stability diagram of device A at a magnetic field of 600 mT with the angle α = 164° with respect to the NW axis (see Fig. 1a) detected as a shift in the transmission phase φ of the resonator, plotted as a function of the two gate voltages VL and VR at a fixed probe frequency of ωp/2π = 5.174 GHz, close to resonance. We observe a characteristic honeycomb pattern of the charge stability diagram of a DQD. Using a capacitance model27,28, we extract the gate-to-dot capacitances CR2 = 44 ± 2 aF, CL2 = 2.0 ± 0.2 aF, CR1 = 5 ± 2 aF and CL1 = 4.6 ± 0.2 aF for device A.
We now focus on one particular inter-dot transition (IDT) marked by a green rectangle in Fig. 2a. The same IDT is shown in Fig. 2b and c at B = 0 T and B = 300 mT respectively, with α = 57°. In Fig. 2d we show the normalized transmission \({(A/{A}_{0})}^{2}\) at B = 0 T, while varying the probe frequency ωp and relative detuning εrel, illustrated by the white line in Fig. 2b. An electron can now reside on either of the two tunnel-coupled dots, constituting a charge qubit. At the IDT, close to charge degeneracy, the electrical dipole moment of the charge qubit interacts with the resonator, resulting in a dispersive shift of the resonance frequency. By fitting input-output theory (see the “Methods" section) to this particular IDT, we extract the inter-dot tunnel coupling t∣B=0/2π = 5.1 ± 1.0 GHz, the charge–photon coupling g0∣B=0/2π = 353 ± 72 MHz, and the charge qubit linewidth γ∣B=0/2π = 1.7 ± 0.7 GHz.
Strong spin–photon coupling
When investigating the magnetic-field dependence of IDTs similar to the ones shown in Fig. 2b, c, we observe two qualitatively different behaviors which we identify as even and odd charge parity configurations described in the “Methods” section. In the following, we investigate a single IDT, shown in Fig. 2c, with an even charge parity.
As illustrated in Fig. 1c, the DQD can be operated as a singlet–triplet qubit when applying a magnetic field. The qubit frequency ωq can be brought into resonance with the cavity frequency ω0 at B ≳ 200 mT, as discussed in more detail below. At the resonance condition (ωq ~ ω0), an anti-symmetric (bonding) and a symmetric (anti-bonding) qubit-photon superposition state are formed. The corresponding resonances can spectroscopically be discriminated only if the splitting 2g between them is larger than the dressed states’ linewidth γ + κ/229. In particular, the hybrid system is considered strongly coupled if the qubit-photon coupling strength g exceeds γ and κ29.
In Fig. 3a, we plot a spectroscopic measurement of the resonator where the singlet–triplet qubit is tuned into resonance by applying an electrostatic detuning εrel relative to the configuration at which S2,0 and \({T}_{1,1}^{+}\) would be fully degenerate in the absence of a a spin-rotating tunneling. Consistent with strong coupling, we observe an avoided crossing between the resonator and the qubit. At the points where the bare qubit frequency ωq and resonator frequency ω0 (dashed, white curves) are degenerate, instead of crossing, they anti-cross. And in Fig. 3a, a faint double peak structure is visible at around εrel ~ 0 as 2g > κ/2 + γ, signature of the strong coupling regime29.
For a quantitative analysis, we fit Lorentzians to the transmission of each trace of constant εrel, we extract the transition frequencies ω± of the dressed states. These are fitted to the Jaynes–Cummings model (solid, white curves in Fig. 3a) described in the “Methods” section. From this fit, we extract the tunnel rate t∣B=300mT/2π = Δso∣B=300mT/4π = 2.54 ± 0.03 GHz and bare spin–photon coupling strength \({g}_{0}^{{{{{{{{\rm{JC}}}}}}}}}{| }_{B=300{{{{{{{\rm{mT}}}}}}}}}/2\pi=123\pm 16\) MHz. The extracted tunnel rate allows to plot the qubit transition frequency \({\omega }_{q}=\sqrt{{({{{\Delta }}}_{{{{{{{{\rm{so}}}}}}}}}/\hslash )}^{2}+{({\varepsilon }_{{{{{{{{\rm{rel}}}}}}}}})}^{2}}\) in Fig. 3a and to identify the resonance condition ωq = ω0 at a small electrostatic detuning εrel/2π = ± 1.0 GHz. We evaluate the effective coupling strength g = g0⋅2t/ωq at the finite detuning εrel/2π = −1.0 GHz and obtain \({g}^{{{{{{{{\rm{JC}}}}}}}}}{| }_{{\epsilon }_{{{{{{{{\rm{rel}}}}}}}}}/2\pi=-1{{{{{{{\rm{GHz,}}}}}}}}}/2\pi=121\pm 16\) MHz, as the spin–photon coupling strength on resonance condition.
In Fig. 3b, we plot a line trace at this detuning value as indicated in Fig. 3a. Despite the large noise, the double peak structure is also clearly visible and stands in stark contrast to the bare resonator transmission at large detuning (see corresponding linetrace in Fig. 3c). Using Eq. (6) derived from input–output theory described in the supplementary, we fit these data at 300 mT and extract the spin-photon coupling strength \({g}_{{\varepsilon }_{{{{{{{{\rm{rel}}}}}}}}}=-1{{{{{{{\rm{GHz}}}}}}}}}/2\pi=139\pm 4\) MHz and qubit dephasing γ/2π = 116 ± 7 MHz where we used the bare resonator decay κ∣B=300mT/2π = 19.8 ± 0.6 MHz. This value agrees well with the one obtained from the Jaynes–Cummings model. Using the values from input–output theory we model the whole anti-crossing using input–output theory in Fig. 3d, observing a very good agreement with the measurement.
All together, this measurement therefore clearly demonstrates that the strong coupling regime between a single microwave photon and a singlet–triplet qubit is reached.
Magnetospectroscopy
To explicitly identify and characterize the spin–orbit eigenstates and to independently verify the character of the singlet–triplet qubit, we now study the magnetic field evolution of the IDT from 0 up to 900 mT applied at the angle α = 130°. We measure the amplitude A and phase φ of the signal transmitted through the resonator as function of detuning ε and magnetic field strength B. A non-zero φ occurs at the IDT when tunneling between the dots is allowed resulting in a non-zero DQD dipole moment. As described in the “Methods” section, we model the DQD by an effective two electron Hamiltonian which allows us to fit the gate voltage and field dependence of the IDT (white dashed line in Fig. 4a). We find that the magneto-dispersion of the IDT is well described using the following fit parameters: the spin-conserving singlet and triplet tunnel rates \({t}_{{\rm {c}}}^{{\rm {S}}}/2\pi \, \approx \, 8.5\) GHz, and \({t}_{{\rm {c}}}^{{\rm {T}}}/2\pi \, \approx \, 3.2\) GHz, the singlet–triplet coupling rate tSO/2π = ΔSO/4π ≈ 2.9 GHz, the electron g-factors of the right and left dots, gR ≈ 1 and gL ≈ 8, as well as the single dot singlet–triplet energy splitting ΔST/2π ≈ 47 GHz. These fit parameters are consistent with parameters obtained previously in this material system19,30,31,32,33. We note, however, that the fit is under-determined and therefore, it does not provide accurate numbers. Nonetheless, the model gives a qualitative, physical understanding of the system and allows us to establish which DQD levels interact with the resonator.
Independently, we gain quantitative information about the system by considering the functional dependence of the amplitude A and phase φ. This is possible because the resonator provides an absolute energy scale allowing for a quantitative analysis of the interaction between the DQD and the resonator and hence to perform qubit spectroscopy22,23,24. This spectroscopy complements the preceding DQD Hamiltonian fit. As described in the “Methods” section, by fitting input–output theory to φ and A simultaneously, we extract the qubit tunnel amplitude t, the qubit linewidth γ, and the qubit–photon coupling strength g as a function of B, which we plot in Fig. 4b. Here, we assume γ as constant in detuning ε.
Using the fits to both, the 2-electron Hamiltonian model and input–output theory in the 2-level approximation, allows us to directly identify several regimes, in each of which the qubit has a different spin-character. Figure 4c shows the corresponding DQD level structure based on the fit parameters as a function of ε for different magnetic field.
At a low magnetic fields around B = 20 mT, the triplet states (blue curves) are Zeeman split and the ground-state curvature is dominated by the anti-crossing between S1,1 and S2,0 (red curves). We find a singlet charge qubit in the weak coupling limit, i.e. the linewidth exceeds the charge–photon coupling by a factor of five. The formation of an asymmetric double-dip structure in φ(ε) between B ~ 0.01 T and B ~ 0.18 T is explained by an interaction between the three states S2,0, S1,1 and \({T}_{1,1}^{+}\) as described in the supplementary material. Traces of φ(ε) with an asymmetric double-dip structure cannot be described by a two-level input–output model and are therefore not analyzed quantitatively here. At B ≈ 50 mT, φ becomes positive. Which we interpreted as a drop of the tunnel rate below the resonator frequency, 2t < ω0.
As B is increased, the triplet state \({T}_{1,1}^{+}\) becomes the ground state for ε < 0, as shown in the second panel of Fig. 4c for B = 300 mT. The spin–orbit interaction couples the singlet and triplet states, leading to an anti-crossing between S2,0 and \({T}_{1,1}^{+}\), which constitutes a singlet–triplet qubit with ωq = ΔSO = 2tSO34,35. In this regime, at larger B, the resonance condition between S2,0 and \({T}_{1,1}^{+}\) occurs at larger ε, because the energy of the bare \({T}_{1,1}^{+}\) state decreases with larger B and the energy of S2,0 decreases with larger ε. Therefore, the IDT is observed at larger ε for increasing B.
Consistent with the interpretation of the formation of a singlet–triplet qubit, we measure an approximately constant tunneling rate t between B ~ 0.18 T and B ~ 0.36 T. In this regime, we extract the average spin–orbit tunneling rate to be \({\bar{t}}_{{{{{{{{\rm{so}}}}}}}}}=1.94\pm 0.02\) GHz. At a magnetic field of B ≈ 370 mT, the resonator phase φ starts to vanish due to the the triplet state \({T}_{2,0}^{+}\) becoming relevant. The triplet state results in a level repulsion between \({T}_{2,0}^{+}\) and \({T}_{1,1}^{+}\) and hence leads to a reduced energy gap between the S2,0 level and the \({T}_{1,1}^{+}\) level. In Fig. 4c, this is illustrated by the smaller energy gap (black arrow) at B = 410 mT compared to the one at B = 300 mT. Due to the reduced gap (\(\Delta_{{{{\mathrm{SO}}}}} < < \, {\omega}_{0}\)), the resonator-qubit coupling is reduced and hence is the singal in φ.
The level structure at large magnetic fields is plotted exemplary for B = 600 mT in the right panel of Fig. 4c. In this regime, the ground-state of the DQD at the IDT is formed by a superposition of the \({T}_{2,0}^{+}\) and \({T}_{1,1}^{+}\) states. We find that the curve of Fig. 4a turns back towards lower ε for increasing B, which can be understood by noting that the spin-polarized triplets \({T}_{2,0}^{+}\) and \({T}_{1,1}^{+}\) form a charge qubit similar to the singlets at low field. While the transition is increasingly dominated by the triplet-charge qubit for increasing B, φ becomes negative at the IDT, because the anti-crossing between the triplet states \({T}_{2,0}^{+}\) and \({T}_{1,1}^{+}\) occurs at much larger frequencies, \(2{t}_{\rm {{c}}}^{{\rm {T}}} > 2{t}_{{{{{{{{\rm{SO}}}}}}}}},{\omega }_{0}\). Hence, the triplet charge qubit frequency does not cross the resonator frequency, leading to a negative phase shift.
At fields B > 700 mT the dispersion turns to higher ε again. Which is not accounted for in our model. A possible explanations to this discrepancy is that the magnetic field not only affects the detuning ε of the DQD but also the total energy. This results in the lead to dot transitions starting to influece the IDT at high magnetic fields. Nevertheless, the data is well described at the magnetic field strengths we investigate in detail.
This large number of detailed findings justify the parameters of the two-electron Hamiltonian introduced above, which, in turn, directly allows us to identify the singlet–triplet spin qubit, for which we find the strong coupling limit to the electromagnetic cavity.
Note, that the extracted qubit linewidth is larger in Fig. 4b compared to the strong-coupling in Fig. 3. This is caused by applying the magnetic field at different angles in the two measurements. The dependence of the qubit parameters on the angle of the in-plane magnetic field is beyond the scope of this manuscript and will be investigated in future studies.
Discussion
In summary, we demonstrate a semiconductor nanowire DQD device with crystal-phase defined tunnel barriers that can be operated as different types of qubits, coupled to a high-impedance, high magnetic field resilient electromagnetic resonator. As the main result, we find a singlet–triplet qubit for which we extract the relevant qubit parameters, especially a large electron spin–photon coupling of g/2π = 139 MHz in the single photon limit, reaching the strong coupling regime g > γ, κ.
Our experiments demonstrate that deterministically grown tunnel barriers allow for a reduced number of gate lines, and that, mediated by intrinsic spin–orbit interaction, singlet–triplet qubits can reach the strong coupling limit for low photon numbers, similar to flopping mode spin qubits36,37. This finding is potentially applicable to other promising platforms with strong spin–orbit interactions, like holes in Ge35. Our nanowire platform without depletion gates results in a significantly reduced gate-induced photon-leakage in the absence of on-chip filtering6,38,39. And, since DQD parameters (such as charging energy and individual tunnel rates) can be set deterministically in the NW growth, multiple NWs with optimal and essentially identical characteristics properties can be obtained simultaneously40 and possibly integrated on the same substrate41. This drastically simplifies the search for an optimal gate regime and renders further gates, such as the top gates in our device, unnecessary. An optimized gate design with resonators with larger impedance28 therefore presents an ideal platform to investigate new phenomena in the ultrastrong coupling regime28,42. Additionally, the large electron spin–photon coupling found in our experiments will be crucial for the implementation of two-qubit gates between distant spin qubits, a milestone on the way towards scalable quantum computers.
Methods
Resonator characterization and analysis
The resonator is fabricated from a thin-film NbTiN (thickness ~ 10 nm), sputtered onto a Si/SiO2 (500 μm/100 nm) substrate21. These resonators can be operated for in-plane fields exceeding 5 T20,21. The large sheet kinetic inductance of the used NbTiN film of Lsq ≈ 90 pH combined with the narrow center conductor width of ~380 nm, and the large distance to the ground plane of ~35 μm results in an impedance of 2.1 kΩ. The resonator can be dc biased using a bias line which contains a meandered inductor ensuring sufficient frequency detuning between the half-wave resonance used in the experiment and a second, low-quality resonance mode at a lower frequency that forms due to the finite inductance of the bias line39. A scanning electron micrograph of the resonator center-conductor is shown in Fig. S1b in the supplementary. One of the two resonator voltage anti-nodes is galvanically connected to gate SGR shown in Fig. 1c of the main text.
Device fabrication
For the NW growth refer to Supplmentary II. After the resonator fabrication, the NWs are deposited on the device area using a micromanipulator. Following the deposition, the NW position and barrier locations are determined using scanning electron imaging. A GaSb-shell, grown for the barrier determination, is then removed before contacting by a 3 min 30 s wet-etching process using MF-319 developer43,44. The contacts and gates are then fabricated using standard e-beam lithography and e-beam evaporation. For the contacts, the native oxide is removed using in-situ argon-milling in the evaporation chamber. For the SGs and TGs no argon-milling is performed and the native oxide is left intact to serve as an insulating layer for the TGs.
Charge parity determination
We measure the phase φ and amplitude A of the resonator as a function of detuning ε and magnetic field B at a probe-frequency ωp/2π = 5.253 GHz, close to the bare resonator frequency. A change in φ reflects the dispersive interaction between the resonator and two anticrossing levels of the DQD45,46. Therefore, the non-zero phase response of the resonator tracks the position of the IDT along the detuning axis. The comparison of the magnetic field dependence of the IDT position to a Hamiltonian model of the DQD allows one to determine the charge parity46,47. Figure S2a and S2b in the Supplementary show two typical low field IDT characteristics of device B.
For an odd number of electrons (Fig. S2b in the Supplementary), the DQD resonance gate voltage VR, at which the IDT is observed, disperses linearly with magnetic field starting from zero. This can be understood considering the Zeeman-splitting of the unpaired electron energy levels and two non-equal Landé g-factors of the two dots. Figure S2c in the Supplementary shows the energy level diagram of a one-electron Hamiltonian including Zeeman-splitting with a g-factor difference of 1.0 and spin–orbit interaction tSO/2π = 5 GHz at a magnetic field of B = 500 mT (green, dashed line in Fig. S2b. The one-electron Hamiltonian is explicitly discussed in the Supplementary material. The arrow points out the center of the IDT (largest curvature of the groundstate48) which corresponds to the largest dipole moment of the DQD and thus to the largest change in φ. This point shifts with B towards increasingly negative values.
For an even number of electrons in the DQD at zero magnetic field (Fig. S2a in the Supplementary), a single dip in phase is observed, but at a low magnetic fields, B ≈ 60 mT, a double dip structure emerges as a function of ε (see Supplementary material for details). This double-dip originates from an interaction between S2,0, S1,1 and \({T}_{1,1}^{+}\) as explained in detail in the supplementary material. The dependence of the IDT on magnetic field for an even number of electrons can be understood using an effective two electron Hamiltonian including spin–orbit interaction described in more detail below. In Fig. S2c in the Supplementary, we plot the energy levels at a magnetic field B = 0.15 T. In contrast to the odd filling, starting at zero magnetic field, the arrow marking the center of the IDT barely changes, consistent with our measurement. The double dip vanishes when further increasing the magnetic field, because of an increasing occupation of the polarized triplet states. Once the Zeeman energy of the triplet state \(\left\vert {T}_{1,1}^{+}\right\rangle\) becomes comparable to the singlet charge tunneling \({t}_{{{{{{{{\rm{c}}}}}}}}}^{{{{{{{{\rm{S}}}}}}}}}\), the position of the IDT as a function of B disperses towards larger ε47,49,50. This transition is marked by the white dashed line at 0.2 T in Fig. S2a in the Supplementary.
Based on the good qualitative agreement between our data and the one electron and two electron Hamiltonian, respectively, we can clearly identify the even and odd charge parities.
Jaynes–Cummings model
In the regime of only two DQD levels being relevant, we model the DQD Hamiltonian as an effective two-level system (qubit) interacting with a single mode in the resonator. The combined system is described by the Jaynes–Cummings model51
where \(\hat{a}\) is the photon annihilation operator, \(\hat{\sigma }\) the qubit lowering operator, and \({\hat{\sigma }}_{z}\) the Pauli z-matrix in the qubit subspace. The qubit frequency is given by \({\omega }_{{\rm {q}}}=\sqrt{{\left(2t\right)}^{2}+{\varepsilon }^{2}}\)26 with the effective qubit–photon coupling strength g = g0⋅2t/ωq accounting for the mixing angle7,52, where g0 is the bare qubit–photon coupling. An excitation from the ground state has the transition frequency52
Input–output theory
To derive the response of the resonator, we use the equations of motion53
The input couplings are denoted by κj and the operators \({\hat{b}}_{{{{{{{{\rm{in}}}}}}}},j}(t)\) capture a coherent drive in port j. In our experiments κ1 ≈ κ2 ≈ κ/2 as the resonator is symmetrically coupled and operates in the strongly over-coupled regime. The output of the cavity can be computed from the input–output relation53
To solve these equations, we approximate54,55
where \(\langle {\hat{\sigma }}_{z}\rangle\) is evaluated at steady state and captures the difference between the population of the excited qubit state and the ground state, accounting for operation at larger temperatures or drive strengths. In our experiments, we operate in the linear regime, \(\langle {\hat{\sigma }}_{z}\rangle=-1\).
To compute the transmission amplitude, we solve Eqs. (3) and (4) upon Fourier transformation and set \(\langle {\hat{b}}_{{{{{{{{\rm{in}}}}}}}},2}\rangle (t)=0\). This results in the transmission amplitude
where the minus sign accounts for the phase difference of π between the input and the output port (λ/2 resonator) and
In the main text, the absolute value squared of this quantity normalized by its maximal value is shown.
The phase of the transmitted signal is given by
As examples, the phase and amplitude of the bare resonance in Coulomb blockade is simultaneously fit in Fig. S1a in the Supplementary and in Fig. S3 in Supplementary the same is done for a linecut of Fig. 4a at 0.25 T.
Estimation of the photon number
Similarly, we may obtain \(\langle \hat{a}\rangle (t)\) by solving Eq. (3). Using \(\langle {\hat{b}}_{{{{{{{{\rm{in}}}}}}}},1}\rangle (t)=\exp (-i{\omega }_{{\rm {p}}}t)\sqrt{{P}_{{{{{{{{\rm{in}}}}}}}}}/{\omega }_{{\rm {p}}}}\), where Pin denotes the power in the input field, we find
In the low-drive regime we consider here, we estimate the photon number as
where we approximate κ1 ≃ κ/2.
Effective two-electron Hamiltonian model
We model an effective two-electron Hamiltonian in the presence of spin–orbit interaction and magnetic field. We write the Hamiltonian in the basis of singlet and triplet states \(\{\vert {S}_{1,1}\rangle,\vert {S}_{2,0}\rangle,\vert {T}_{1,1}^{\pm,0}\rangle,\vert {T}_{2,0}^{\pm,0}\rangle \}\), with the subscripts indicating the charge distribution in the DQD. The Hamiltonian reads
with the spin quantum-number conserving Hamiltonians
Here, \({t}_{{\rm {c}}}^{\rm {{S,T}}}\) are the tunnel rates between the two singlets, and between the two triplet states respectively, and ΔST is the single-dot singlet–triplet splitting that separates the T2,0 states from the S2,0 states. The Zeeman Hamiltonian is given by
where gL (gR) is the Landé g-factor of the left (right) dot. Because of the large intrinsic spin–orbit interaction in the NW, we include the spin–orbit Hamiltonian that couples the singlet and triplet states with opposite charge configuration using the spin–orbit tunnel rate tSO as
Data availability
The nummerical data used in this study are available in the zenodo database https://doi.org/10.5281/zenodo.7777840.
References
Hanson, R., Kouwenhoven, L. P., Petta, J. R., Tarucha, S. & Vandersypen, L. M. Spins in few-electron quantum dots. Rev. Mod. Phys. 79, 1217 (2007).
Zwanenburg, F. A. et al. Silicon quantum electronics. Rev. Mod. Phys. 85, 961 (2013).
Vandersypen, L. et al. Interfacing spin qubits in quantum dots and donors-hot, dense, and coherent. npj Quantum Inf. 3, 34 (2017).
Chatterjee, A. et al. Semiconductor qubits in practice. Nat. Rev. Phys. 3, 157–177 (2021).
Childress, L., Sørensen, A. & Lukin, M. D. Mesoscopic cavity quantum electrodynamics with quantum dots. Phys. Rev. A 69, 042302 (2004).
Petersson, K. D. et al. Circuit quantum electrodynamics with a spin qubit. Nature 490, 380–383 (2012).
Stockklauser, A. et al. Strong coupling cavity qed with gate-defined double quantum dots enabled by a high impedance resonator. Phys. Rev. X 7, 011030 (2017).
Mi, X., Cady, J., Zajac, D., Deelman, P. & Petta, J. R. Strong coupling of a single electron in silicon to a microwave photon. Science 355, 156–158 (2017).
Mi, X. et al. A coherent spin–photon interface in silicon. Nature 555, 599–603 (2018).
Samkharadze, N. et al. Strong spin–photon coupling in silicon. Science 359, 1123–1127 (2018).
Landig, A. J. et al. Coherent spin–photon coupling using a resonant exchange qubit. Nature 560, 179–184 (2018).
van Woerkom, D. J. et al. Microwave photon-mediated interactions between semiconductor qubits. Phys. Rev. X 8, 041018 (2018).
Borjans, F., Croot, X., Mi, X., Gullans, M. & Petta, J. Resonant microwave-mediated interactions between distant electron spins. Nature 577, 195–198 (2020).
Harvey-Collard, P. et al. Coherent spin–spin coupling mediated by virtual microwave photons. Phys. Rev. X 12, 021026 (2022).
Petta, J. R. et al. Coherent manipulation of coupled electron spins in semiconductor quantum dots. Science 309, 2180–2184 (2005).
Landig, A. J. et al. Microwave-cavity-detected spin blockade in a few-electron double quantum dot. Phys. Rev. Lett. 122, 213601 (2019).
Bøttcher, C. et al. Parametric longitudinal coupling between a high-impedance superconducting resonator and a semiconductor quantum dot singlet-triplet spin qubit. Nat. Commun. 13, 4773 (2022).
Lehmann, S., Wallentin, J., Jacobsson, D., Deppert, K. & Dick, K. A. A general approach for sharp crystal phase switching in inas, gaas, inp, and gap nanowires using only group v flow. Nano Lett. 13, 4099–4105 (2013).
Nilsson, M. et al. Tuning the two-electron hybridization and spin states in parallel-coupled inas quantum dots. Phys. Rev. Lett. 121, 156802 (2018).
Samkharadze, N. et al. High-kinetic-inductance superconducting nanowire resonators for circuit qed in a magnetic field. Phys. Rev. Appl. 5, 044004 (2016).
Ungerer, J. H. et al. Performance of high impedance resonators in dirty dielectric environments. EPJ Quantum Technol. 10, 41 (2023).
Borjans, F. et al. Probing the variation of the intervalley tunnel coupling in a silicon triple quantum dot. PRX Quantum 2, 020309 (2021).
Mi, X., Péterfalvi, C. G., Burkard, G. & Petta, J. R. High-resolution valley spectroscopy of Si quantum dots. Phys. Rev. Lett. 119, 176803 (2017).
Ibberson, D. J. et al. Large dispersive interaction between a cmos double quantum dot and microwave photons. PRX Quantum 2, 020315 (2021).
Nilsson, M. et al. Single-electron transport in inas nanowire quantum dots formed by crystal phase engineering. Phys. Rev. B 93, 195422 (2016).
van der Wiel, W. G. et al. Electron transport through double quantum dots. Rev. Mod. Phys. 75, 1–22 (2002).
Van der Wiel, W. G. et al. Electron transport through double quantum dots. Rev. Mod. Phys. 75, 1 (2002).
Scarlino, P. et al. In situ tuning of the electric-dipole strength of a double-dot charge qubit: charge-noise protection and ultrastrong coupling. Phys. Rev. X 12, 031004 (2022).
Blais, A., Grimsmo, A. L., Girvin, S. M. & Wallraff, A. Circuit quantum electrodynamics. Rev. Mod. Phys. 93, 025005 (2021).
Fasth, C., Fuhrer, A., Samuelson, L., Golovach, V. N. & Loss, D. Direct measurement of the spin–orbit interaction in a two-electron inas nanowire quantum dot. Phys. Rev. Lett. 98, 266801 (2007).
Nadj-Perge, S. et al. Disentangling the effects of spin–orbit and hyperfine interactions on spin blockade. Phys. Rev. B 81, 201305 (2010).
Trif, M., Golovach, V. N. & Loss, D. Spin dynamics in inas nanowire quantum dots coupled to a transmission line. Phys. Rev. B 77, 045434 (2008).
Jünger, C. et al. Magnetic-field-independent subgap states in hybrid rashba nanowires. Phys. Rev. Lett. 125, 017701 (2020).
Mutter, P. M. & Burkard, G. All-electrical control of hole singlet-triplet spin qubits at low-leakage points. Phys. Rev. B 104, 195421 (2021).
Jirovec, D. et al. A singlet–triplet hole spin qubit in planar ge. Nat. Mater. 20, 1106–1112 (2021).
Yu, C. X. et al. Strong coupling between a photon and a hole spin in silicon. Nat. Nanotechnol. 18, 741–746 (2023).
Burkard, G. et al. Semiconductor spin qubits. Rev. Mod. Phys. 95, 025003 (2023).
Mi, X. et al. Circuit quantum electrodynamics architecture for gate-defined quantum dots in silicon. Appl. Phys. Lett. 110, 043502 (2017).
Harvey-Collard, P. et al. On-chip microwave filters for high-impedance resonators with gate-defined quantum dots. Phys. Rev. Appl. 14, 034025 (2020).
Nilsson, M. et al. Parallel-coupled quantum dots in inas nanowires. Nano Lett. 17, 7847–7852 (2017).
Ram, M. S. et al. High-density logic-in-memory devices using vertical indium arsenide nanowires on silicon. Nat. Electron. 4, 914–920 (2021).
Forn-Díaz, P., Lamata, L., Rico, E., Kono, J. & Solano, E. Ultrastrong coupling regimes of light–matter interaction. Rev. Mod. Phys. 91, 025005 (2019).
Gatzke, C., Webb, S., Fobelets, K. & Stradling, R. In situ raman spectroscopy of the selective etching of antimonides in gasb/alsb/inas heterostructures. Semicond. Sci. Technol. 13, 399 (1998).
Barker, D. et al. Individually addressable double quantum dots formed with nanowire polytypes and identified by epitaxial markers. Appl. Phys. Lett. 114 (2019).
Frey, T. et al. Dipole coupling of a double quantum dot to a microwave resonator. Phys. Rev. Lett. 108, 046807 (2012).
Crippa, A. et al. Gate-reflectometry dispersive readout and coherent control of a spin qubit in silicon. Nat. Commun. 10, 1–6 (2019).
Ezzouch, R. et al. Dispersively probed microwave spectroscopy of a silicon hole double quantum dot. Phys. Rev. Appl. 16, 034031 (2021).
Park, S. et al. From adiabatic to dispersive readout of quantum circuits. Phys. Rev. Lett. 125, 077701 (2020).
Schroer, M., Jung, M., Petersson, K. & Petta, J. R. Radio frequency charge parity meter. Phys. Rev. Lett. 109, 166804 (2012).
Malinowski, F. K. et al. Spin of a multielectron quantum dot and its interaction with a neighboring electron. Phys. Rev. X 8, 011045 (2018).
Shore, B. W. & Knight, P. L. The Jaynes–Cummings model. J. Mod. Opt. 40, 1195–1238 (1993).
Blais, A., Huang, R.-S., Wallraff, A., Girvin, S. M. & Schoelkopf, R. J. Cavity quantum electrodynamics for superconducting electrical circuits: an architecture for quantum computation. Phys. Rev. A 69, 062320 (2004).
Gardiner, C. & Zoller, P. Quantum Noise: a Handbook of Markovian and non-Markovian Quantum Stochastic Methods with Applications to Quantum Optics (Springer Science & Business Media, 2004).
Wong, C. H. & Vavilov, M. G. Quantum efficiency of a single microwave photon detector based on a semiconductor double quantum dot. Phys. Rev. A 95, 012325 (2017).
Schöndorf, M., Govia, L. C. G., Vavilov, M. G., McDermott, R. & Wilhelm, F. K. Optimizing microwave photodetection: input–output theory. Quantum Sci. Technol. 3, 024009 (2018).
Acknowledgements
We acknowledge fruitful discussions with Simon Zihlmann, Roy Haller, Andrea Hofmann, Stefano Bosco, Romain Maurand and Antti Ranni, and support in setting-up the experiments by Fabian Oppliger, Roy Haller, Luk Yi Cheung, and Deepankar Sarmah. This research was supported by the following institutions: the Swiss Nanoscience Institute, SNI (J.H.U., A.B., C.S.); the Swiss National Science Foundation through grant 192027 (A.P., C.S.); the NCCR Quantum Science and Technology, NCCR-QSIT (J.H.U., A.P., J.R., C.S.); the NCCR Spin Qubit in Silicon, NCCR-Spin (J.H.U., A.P., A.K., J.R., C.S.); the Eccellenza Professorial Fellowship PCEFP2_194268 (P.P.P.); the European Union’s Horizon 2020 research and innovation program, FET-open project AndQC, agreement No. 828948 (C.S.); the European Union’s Horizon 2020 research and innovation program, FET-open project TOPSQUAD, agreement No. 847471 (A.P., C.S.); NanoLund (S.L., C.T., K.A.D., V.F.M.); the Knut & Alice Wallenberg Foundation, KAW (K.A.D.); the SNSF through grant 200021_200418 (P.S.); the SERI through grant contract number MB22.00081 (P.S.); European Union’s Horizon 2020 research and innovation program: grant agreement No. 787414, ERC-Adv TopSupra (A.B.).
Author information
Authors and Affiliations
Contributions
J.H.U., A.P., A.K., S.L., J.R., C.T., K.A.D., V.F.M., P.S., A.B., and C.S. developed techniques that were needed to fabricate and measure the device. S.L. grew the nanowire with contributions from C.T. and K.A.D. J.H.U. and A.P. fabricated the device. J.H.U., A.P. and A.K. performed the measurements. P.P.P. devloped the input-output theory allowing for quantitative data analysis. J.H.U. and A.P. analyzed the data with input from all authors. J.H.U. and A.P. wrote the manuscript with contributions from all authors. C.S. supervised the project.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. A peer review file is available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Ungerer, J.H., Pally, A., Kononov, A. et al. Strong coupling between a microwave photon and a singlet-triplet qubit. Nat Commun 15, 1068 (2024). https://doi.org/10.1038/s41467-024-45235-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-024-45235-w
- Springer Nature Limited