Abstract
Single-electron spin qubits employ magnetic fields on the order of 1 Tesla or above to enable quantum state readout via spin-dependent-tunnelling. This requires demanding microwave engineering for coherent spin resonance control, which limits the prospects for large scale multi-qubit systems. Alternatively, singlet-triplet readout enables high-fidelity spin-state measurements in much lower magnetic fields, without the need for reservoirs. Here, we demonstrate low-field operation of metal-oxide-silicon quantum dot qubits by combining coherent single-spin control with high-fidelity, single-shot, Pauli-spin-blockade-based ST readout. We discover that the qubits decohere faster at low magnetic fields with \({T}_{2}^{\,\text{Rabi}\,}=18.6\) μs and \({T}_{2}^{* }=1.4\) μs at 150 mT. Their coherence is limited by spin flips of residual 29Si nuclei in the isotopically enriched 28Si host material, which occur more frequently at lower fields. Our finding indicates that new trade-offs will be required to ensure the frequency stabilization of spin qubits, and highlights the importance of isotopic enrichment of device substrates for the realization of a scalable silicon-based quantum processor.
Similar content being viewed by others
Introduction
The rapid progress of spin quantum bits (qubits) in silicon quantum dots (QDs) has been fuelled by coherent electron spin resonance (ESR), either driven by an alternating (ac) magnetic field1 or electric field2,3. To date, ESR has enabled the measurement of long coherence times1,4,5,6, and the demonstration of high-fidelity single- and two-qubit logic gates approaching the fault tolerance threshold7,8,9,10,11,12. In most of these demonstrations, single-shot spin readout was performed via spin-selective tunnelling of a single spin to a reservoir13; however, this technique is problematic for the operation of large-scale multi-qubit architectures14,15 based on industrial manufacturing14,16,17,18. In order to work, it would require complex, coherent single-spin shuttling19,20,21 or a chain of swap gate operations22,23 to read out qubits distant from a reservoir. Furthermore, quantum error correction protocols require simultaneous spin-state readout at arbitrary locations in the large-scale qubit array15. The preferred method for spin-readout is, therefore, singlet–triplet (ST) readout via Pauli spin blockade (PSB) in a double-QD (DQD) system24. Besides alleviating the design constraints imposed by reservoir readout, single-shot dispersive ST readout can also leverage state-of-the-art reflectometry technology to enable gate-based sensors with extremely small on-chip footprint25,26,27,28,29. Furthermore, ST readout forms the foundation of parity measurements, a main ingredient of many quantum error correction protocols15, and does not require the Zeeman splitting energy to be much larger than the thermal energy, which is a limiting constraint with reservoir-based readout13. It therefore constitutes a robust readout technique that allows qubit operation over a wide range of magnetic fields. Low magnetic fields, in particular, are highly desirable because they enable qubit operation at lower spin resonance frequencies, simplifying microwave engineering and requiring less expensive signal generators. Coherent ESR and high-fidelity ST readout are therefore the key elements for the implementation of a scalable, silicon-based quantum processor14,15. Previous experiments have shown the compatibility of these two techniques for electrons in GaAs30,31; however in silicon, demonstrations using electron spins have so far remained incoherent22, while those employing hole spins are yet to achieve single-shot readout32.
In this work, we demonstrate coherent, single-electron spin control with high-fidelity ST readout at a direct current (dc) magnetic field of 150 mT. This new combination of control and readout protocols enables the investigation of the 29Si nuclear magnetic field seen by a single-electron spin qubit in a 800-p.p.m. isotopically enriched silicon substrate at low magnetic fields. We find that the fidelity of ESR control is affected by a drift of the qubit resonance frequency due to fluctuations in the hyperfine field generated by the 800-p.p.m. 29Si nuclei, and that the amount of this drift increases at lower magnetic field. The field dependence indicates that the hyperfine field drift is mostly driven by the ESR signal used to measure it, a finding that informs critical engineering trade-offs in how to compensate for nuclear drifts when scaling up silicon spin qubits in the low-magnetic-field paradigm.
Results
Device operation and ST readout
The device consists of a linear array of silicon metal oxide semiconductor (Si-MOS) QDs, electrostatically defined by a palladium (Pd) gate stack33 on an isotopically enriched 28Si epi layer34 (see Methods section). Figure 1a shows a false-coloured scanning electron micrograph of a device nominally identical to the one used in this study. A cross-sectional schematic is plotted in Fig. 1b. We have labelled the QD accumulation gates (G1–G6), the confinement gate that confines the QDs laterally, the reservoir gate that accumulates the electron reservoir for loading and unloading electrons, the single-electron transistor (SET) charge sensor (ST, sensor left barrier, sensor right barrier), and the short of the broadband ESR antenna to apply MW pulses35 for spin control.
When tuning up the device, we use the following procedure to find the PSB region that gives us high-fidelity, single-shot ST readout at low magnetic field. First, we carefully tune all the gate voltages to accumulate two QDs at the approximate locations indicated in Fig. 1b, using the charge sensing technique described in ref. 36. We then choose the (1,3)–(0,4) anti-crossing, shown in Fig. 1c, as our working point. We assume the first two electrons in QD2 to form a singlet and not to interact with the third and fourth electrons during the experiment. Second, we either initialize the two QDs in a singlet state or in a mixed state of singlet and triplet. When pulsing from point A to point B (yellow arrow), we load a fourth electron on QD2, with the last two electrons forming an anti-parallel spin pair (singlet). Further pulsing to point C will separate these two electrons across the two QDs, keeping them in the singlet state22. Alternatively, when pulsing from point D to C, we will randomly remove one of the four electrons from QD2. The spin of the remaining, third electron could be either anti-parallel or parallel with the spin in QD1, leaving the two QDs initialized in a mix of triplet and singlet. Third, we find the region of PSB, by alternately initializing a singlet and a mixed state, and pulsing to a point around the (1,3)–(0,4) anti-crossing. Figure 1d plots the difference in the SET current for the two different initializations, performed interleaved to reject slow drifts of the charge sensor. When the two QDs are in the singlet state, the single electron in QD1 can tunnel onto QD2 causing a change in charge configuration from (1,3) to (0,4). However, when they are in the triplet state, tunnelling is inhibited by PSB and the system remains in the (1,3) charge configuration24. Therefore, initialization into the mixed state will result in some probability for the charge sensor giving a reading that represents a triplet. We detect a clear standard PSB region and two enhanced latching regions, in which the very different tunnelling times from the two QDs to the reservoir are used to cause a state-dependent change in total charge37.
We have designed the orientation of the SET to maximize its sensitivity to inter-dot charge tunnelling events, and achieve good signal contrast for ST readout. As shown in the SET current histogram in Fig. 1e, the signal peaks for standard PSB are separated by \(4.9\sigma\), indicating a charge state readout fidelity \(> 99.8\%\). The enhanced latching readout mechanism further increases the signal contrast between the singlet and triplet state, up to \(9.8\sigma\) (see Fig. 1f, g). Such good contrast would allow charge readout with \(<0.005\%\) error; however, we found the latched metastate lifetime to be 2 ms or shorter. This is only one order of magnitude slower than the 120 μs integration time that is required to achieve good signal separation for our experimental setup. Consequently, we notice a non-zero background between the singlet and triplet peaks in Fig. 1g, evidencing decay from the triplet state to the singlet state during measurement. To avoid the spin readout error caused by the latched metastate relaxation as well as mapping errors37, we chose the standard PSB region for readout. The triplet lifetime for standard PSB is 22 ms, which results in a ~0.5% spin-to-charge conversion error. This reduces the total fidelity of the single-shot ST readout using standard PSB to \(99.3\%\). The latched metastate lifetime could be improved in future experiments by defining a third electron under G5 to fine-tune the electron tunnelling rate from QD1 and QD2 to the reservoir38.
Spin control and coherence times
In this study, we control the spins of the electrons using an ac magnetic field generated by the on-chip microwave antenna35. In Fig. 2a, we plot a schematic of the energy level diagram as a function of energy detuning \(\epsilon\) and in Fig. 2b the pulse sequences that we used to achieve ESR. As shown in Fig. 2c for \({B}_{z}^{0}=150\) mT, we find two resonance peaks that correspond to rotations of QD1 (lower frequency) and QD2 (higher frequency). When we decrease \(\epsilon\), the splitting between the two peaks increases, denoting the larger exchange coupling \(J\) between the electrons and mapping out the energy structure of the (1,3)–(0,4) anti-crossing in the shallow detuning region. Next, we investigate the coherence of the spin qubits in low magnetic fields. By varying the ESR pulse time, we observe clear Rabi oscillations (Fig. 2d) at a magnetic field as low as \({B}_{z}^{0}=150\) mT, with \({T}_{2}^{\,\text{Rabi}\,}=18.6\)s. In Fig. 2e, we plot the Rabi chevron for one of the qubits at \({B}_{z}^{0}=450\) mT. We also use a Ramsey sequence (Fig. 2f) to measure \({T}_{2}^{* }\) at various magnetic fields. The observed \({T}_{2}^{* }\) values are reported in Table 1.
The ability to perform coherent control on the spin states allows us to experimentally validate the combined initialization, control and measurement fidelity. We extract the maximum readout visibility for the \(\left|\uparrow \uparrow \right\rangle\) state by fitting the Rabi oscillations in Fig. 2d. The maximum visibility is 87.1\(\pm\)1.9%, which is noticeably lower than our earlier estimate of the readout fidelity. During this measurement campaign, we observed frequent jumps in the ESR frequencies of both qubits due to spin flip of the surrounding 29Si nuclei. This renders it difficult to keep the microwave frequency exactly on-resonance for the duration of the measurement (see also Fig. 2e). Therefore, the true readout visibility of the \(\left|\uparrow \uparrow \right\rangle\) state may not be reflected in this measurement. We also studied the maximum readout visibility for the three other spin states (\(\left|\downarrow \uparrow \right\rangle\), \(\left|\uparrow \downarrow \right\rangle\), and \(\left|\downarrow \downarrow \right\rangle\)) using complementary measurements. The visibility for \(\left|\uparrow \downarrow \right\rangle\) is as high as 99.5\(\pm\)0.7%, consistent with the readout fidelity estimated previously. The results are summarized in Table 2 with more details given in the Methods section.
Nuclear spin dynamics
The robustness of ST readout allows us to employ tracking of the ESR frequency as a function of magnetic field over a wide range from \({B}_{z}^{0}=150\,{\mathrm{mT}}\) to 1.4 T. The existence of a strong field dependence of ESR frequency drifts points to underlying processes arising inside the MOS devices, not compatible with either charge noise or drifts in the applied magnetic field. As we argue in this section, the residual (800 p.p.m.) 29Si nuclear spins in the isotopically enriched substrate are responsible, and their increased role at lower magnetic field is a key result that emerges from the spin control sequences we employ.
As already noticeable in Fig. 2e, we observe fluctuations of the ESR frequencies \(\Delta {f}_{\text{ESR}}={f}_{\text{ESR}}({t}_{2})-{f}_{\text{ESR}}({t}_{1})\) of both qubits in time. More detailed data is shown in Fig. 3a, where we track the ESR frequencies of both qubits over 140 min. There is no correlation between \(\Delta {f}_{\,\text{ESR}}^{\text{QD1}\,}\) and \(\Delta {f}_{\,\text{ESR}}^{\text{QD2}\,}\), indicating that any fluctuations are caused by a highly localized effect, consistent with a nuclear spin origin, and similar to observations that were published in ref. 10 on a different device. Figure 3b–g shows the histograms of \(\Delta {f}_{\text{ESR}}\) at three different magnetic fields for both qubits. We observe that the distribution of \(\Delta {f}_{\text{ESR}}\) becomes narrower as the magnetic field increases. To better quantify this effect, we plot the standard deviation of \(\Delta {f}_{\,\text{ESR}}^{\text{QD1}\,}\) as a function of magnetic field in Fig. 3h. The increase of this standard deviation at lower magnetic field is not easily explained by nuclear diffusion through dipole–dipole interactions, and suggests other mechanisms for nuclear spin flips40,41,42. As these mechanisms provide a critical limiting behaviour for frequency drift and therefore control fidelity, we seek a numerical model to explain it. The increased fluctuations at lower magnetic field point to the role of the electron spin in the dot, which may more easily drive nuclear spins when the electron and nuclear Zeeman energies are lower. There are several mechanisms which would show this behaviour qualitatively; to isolate which of these are most likely to lead to the observed phenomena, we must look quantitatively at the underlying hyperfine interactions.
Hyperfine interactions
First, we simplify hyperfine modelling drastically by treating two or four electrons as inert relative to nuclei, since overlapping electrons paired into singlet states have no net hyperfine interaction. Likewise, we treat three electrons as a single electron relative to spin interactions, neglecting the other two electrons, which form a singlet. The largest hyperfine interaction for a single electron is the Fermi-contact interaction, with Hamiltonian
where \({\bf{S}}\) is the single electron vector spin operator and \({{\bf{I}}}_{j}\) is the vector spin operator for the jth 29Si nucleus. Note that here we put the wafer-normal direction as \(x\) and the direction of the in-plane magnetic field as \(z\) to conform to common conventions in electron-nuclear magnetic resonance. The principle effect of the contact hyperfine of importance to the present results is the Overhauser shift, given as
for some configuration of nuclear spin projections \(\langle {I}_{j}^{z}\rangle\).
Estimating the size of each \({A}_{j}\) requires knowing the shape of the envelope wavefunction \(\psi ({\bf{r}})\) as well as the placement of the 29Si nuclei. For the former, we have employed detailed self-consistent Schrödinger–Poisson simulations of the device, including full three-dimensional gate stacks to capture the potential. The details of the electrostatic wavefunction model can be found in the Methods section. We acknowledge that these models do not capture the wavefunction perfectly, as they omit details of electron–electron interactions for closed-shell electrons, have approximate strain models, and do not capture realistic charge offset and disorder effects in real dots. For the placement of 29Si, these distribute randomly during epitaxy and so can only be treated statistically.
The contact term is not the only hyperfine term present; we observe the effects of the electron-nuclear dipole–dipole interaction, which is summarized as
The traceless tensor \({{\bf{D}}}_{j}\), discussed in detail in the Methods section, possesses both diagonal and off-diagonal terms. The diagonal terms behave similarly to the contact hyperfine interaction, in that a nuclear flip due to this term is always accompanied by an electron flip, therefore costing the electron Zeeman energy \(g{\mu }_{\text{B}}{B}_{z}^{0}\). However, these dipole–dipole diagonal terms are nearly two orders of magnitude smaller than the contact terms, as calculated in ref. 43, and so may be neglected. Much more critical for our model of hyperfine dynamics are off-diagonal, or anisotropic, terms of the coupling tensor \({{\bf{D}}}_{j}\), as these may allow nuclear spin flips without associated electron flips, effectively forming a correction in the local field direction of the nucleus due to the electron spin’s polarization.
Model of driven nuclear fluctuations
The dominant term driving nuclear spin flips in the experiments presented here arises from the combination of a tilted local magnetic field for each nucleus due to the anisotropic dipole–dipole interaction in conjunction with the driving of ESR frequencies at the sum or difference frequencies of the electron and nuclear Zeeman frequencies. This interaction, when driven for times long relative to thermal relaxation times, has been understood for many decades to lead to dynamic nuclear polarization in silicon donor ensembles44. In those experiments, the process is referred to as the solid-state effect. To summarize the interaction, consider a single nucleus and a single electron. In the rotating-wave-approximated frame rotating at the applied ESR frequency \(\omega\), and keeping only the secular terms of the hyperfine interaction, the Hamiltonian term for nucleus \(j\) is
where \(g\approx 2\) is the \(g\)-factor for electrons in silicon, \({\mu }_{\text{B}}\) is the Bohr magneton, \(\gamma /2\pi =-8.467\) MHz/T is the gyromagnetic ratio for a 29Si nucleus, and \({B}_{z}^{0}\) is the applied magnetic in-plane field in the \(z\)-direction. Because the anisotropic dipolar interaction coefficients \({D}_{j}^{zx},{D}_{j}^{zy}\) are by far the smallest term in this expression, they may be treated as a perturbation. In the interaction picture, we find that due to the Rabi drive at rate \(\Omega\), the interaction-picture perturbation has oscillatory terms at frequencies \(\omega -g{\mu }_{\text{B}}{B}_{z}^{0}/\hslash \pm \gamma {B}_{z}^{0}\). When integrating to first order in the dipolar terms for a Rabi drive of duration \(\tau\), at the peak frequencies \(\omega =(g{\mu }_{\text{B}}/\hslash \pm \gamma ){B}_{z}^{0}\), the first-order probability of a nuclear spin flip is \({p}_{j}=(1/32){(\Omega \tau )}^{2}[{({D}_{j}^{zx})}^{2}+{({D}_{j}^{zy})}^{2}]/{(\gamma {B}_{z}^{0})}^{2}.\) For the experiment with results shown in Fig. 3, the pulse duration was \(\tau =100\) μs, and the Rabi drive may be estimated as approximately \(\pi /(1\,\upmu{\mathrm{s}})\), although the Rabi drive was not calibrated in this experiment. Under these conditions, the peak probability of a flip per Rabi pulse scales as \({(1/{B}_{z}^{0})}^{2}\), varying substantially from one 29Si to the next, and may be as high as \(1{0}^{-4}\) for well-coupled nuclei at low magnetic field. When a flip does happen, the Overhauser shift \(\delta \omega\) changes by \({A}_{j}\); hence, the Overhauser variance for a single nucleus after \(N\) trials, treating each nucleus as a balanced random telegraph process, is \([1-{(1-2{p}_{j})}^{2N}]{A}_{j}^{2}/4\). We estimate the total variance of observed frequency shifts by summing this variance over all 29Si nuclei (treated, appropriately, as independent), for a number of trials \(N\) given by the number of single-shot measurements used at each applied frequency (200) times the number of frequency sweeps in the data (70). We approximate in this calculation that each sweep over the ESR frequency always hits each resonance once.
The ESR drive is not the only process that causes a change in a nucleus’ local transverse field, enabling a spin flip. We have also considered the probability that the process of the electron tunnelling suddenly changing the local magnetic field of a nuclear spin (ionization shock), may cause a nuclear flip. The associated probability of a flip may be estimated as the squared amplitude of the first-order perturbative mixing of two nuclear spin states due to a particular hyperfine term45,46. For the contact hyperfine term, this probability is approximately \((1/16){[\hslash {A}_{j}/(g{\mu }_{\text{B}}{B}_{z}^{0})]}^{2}.\) For the anisotropic dipolar term, this probability is approximately \((1/16)[{({D}^{zy})}^{2}+{({D}^{zx})}^{2}]/{(\gamma {B}_{z}^{0}\pm {A}_{j})}^{2}.\) These probabilities are lower than the ESR-induced flip probabilities discussed above, but they may occur for every single measurement for every frequency swept in the experiment.
Other mechanisms for flipping nuclei are even smaller. We also consider the probabilities of nuclear-nuclear flip-flop due to the contact hyperfine term when the dot is occupied by an electron. We consider the coherent evolution of each nuclear pair in their local hyperfine field due to this effective interaction, and calculate the variance of ESR frequency shifts assuming each nuclear pair is independent.
Notably, all of the nuclear flip probabilities above scale as the inverse square of the applied field, \({(1/{B}_{z}^{0})}^{2}\). As the probabilities are very small at high \({B}_{z}^{0}\), calculated variances may be simply summed and each are proportional to the associated probability and therefore to \({(1/{B}_{z}^{0})}^{2}\); the root-mean-square (RMS) deviation therefore scales as \(1/{B}_{z}^{0}\), as seen in the experimental data. At very low field, our expression saturates to a total width, which may be regarded as \(1/\sqrt{2}\pi {T}_{2}^{* }\) in the ergodic limit, that is, the expected measure of \({T}_{2}^{* }\) if averaging over the full range of drift. The question to be answered by our modelling above is whether the amplitude of that variation numerically matches the data. We find that our model is consistent with the data, if the \(1/e\) diameter of the wavefunction is smaller than about 8 nm.
To evaluate the typicality of our real sample, we look at the coefficient for the RMS frequency derivation, \(c\), such that \(\Delta {f}_{\text{ESR}}=c/{B}_{z}^{0}\) at high \({B}_{z}^{0}\). We calculate \(c\) for 10,000 virtual samples, each with the same wavefunction size corresponding to vertical field \(F=20\) mV/nm and \(1/e\) diameter 7 nm, in which the 800 p.p.m. 29Si are randomly placed relative to the wavefunction. Figure 3h shows example RMS frequency deviations as calculated by finding all probabilities and variances for all 29Si nuclei as a function of magnetic field for 30 of these virtual sample crystals, all with a diameter of 7 nm. We find that some simulated samples have a higher variance and ergodic \({T}_{2}^{* }\) than the data, and some lower. The full distribution of 10,000 coefficients \(c\) is extremely broad and the experimentally observed data sits near the mean of the distribution, as shown in Fig. 4. We further find that in our simulation the variance is highly dominated by the ESR-driving term relative to other spin-flip processes we considered. Averaged over those virtual samples with a coefficient \(c\) within a factor of 2 of the experimentally observed coefficient, we find that 99.4% of the variance results from the solid-state effect, that is, ESR driving on states mixed by the off-diagonal anisotropic dipolar interaction. The much smaller contribution of the other interactions we considered is shown in Table 3.
Although other processes are certainly at play, which may influence the drift of the ESR frequency, we find the theory we have presented here to be highly consistent with the observed data, using a model with only physically constrained parameters. While many approximations were necessary to estimate the wavefunction size and the nuclear spin-flip probabilities, the broad distribution of outcomes provided by the random placement of 800 p.p.m. 29Si in the small wavefunction means that small deviations from these approximations would not be discernible. Our model also indicates that the dominant source of the variance of the ESR frequency would be reduced substantially if limiting the scanning of microwaves to avoid the conditions that drive nuclear spin flips.
Discussion
In summary, we have successfully operated spin qubits in a silicon platform with a readout scheme showing fidelity higher than 99.3% and the ability to work in a broad range of magnetic fields. The ST readout scheme enables coherent control of single spins at a magnetic field of 150 mT and a resonance frequency as low as 4.1 GHz. Such lower frequency qubit operation significantly improves the scalability prospects for future silicon quantum processors, and also reveals important magnetic noise effects that become more significant when operating in a low magnetic field environment. Despite using an isotopically enriched 28Si substrate, there remain residual 29Si nuclear spins located in the vicinity of the qubits, causing fluctuations in the qubit operation frequencies. We observe the nuclear spin flip rate to increase as the applied external magnetic field decreases, consistent with a numerical model of nuclear spin fluctuations resulting from the ESR drive and anisotropic dipolar interactions. While these 29Si nuclear spins could potentially be used as a resource for quantum computation47, our findings suggest further improvement of the 28Si isotopic enrichment may be crucial for building a truly scalable spin-based quantum processor.
Methods
Measurement setup
Figure 1a, b shows a scanning electron micrograph and a cross-sectional schematic of the sample used in this study. It is fabricated on top of a 900-nm-thick, isotopically enriched 28Si epi layer with 800 p.p.m. residual 29Si on a natural silicon substrate34. We first grow a 7-nm-thick thermal SiO2 plus a 3-nm atomic layer deposition (ALD) aluminium oxide to prevent gate to substrate leakage. Then, we use electron-beam lithography to write the nanoscale gate pattern and perform resist development in pre-cooled (−20 °C) methyl isobutyl ketone solution with ultrasound agitation. In the next step, we evaporate Pd onto the chip to form the gate electrodes. Since Pd has a much smaller grain size than aluminium, we routinely achieve gate features as narrow as 12 nm. A 2-m-thin Titanium (Ti) layer is evaporated prior to Pd deposition to enhance the cohesion of the Pd gate onto the oxide. The above lithography process is repeated several times to form the stack of Pd gate electrodes. Since Pd does not have a native oxide, we use ALD to grow 3- to 4-m aluminium oxide on top of the gates to provide electrical insulation between different layers. Lastly, the sample is annealed in forming gas at 400 °C for 15 min to repair the damage caused by lithography.
Stanford Research Systems SIM928 modular programmable voltage sources are used to dc-bias all-gate electrodes shown in Fig. 1a, b. In addition, voltage pulses from an arbitrary waveform generator (Tektronix AWG7122) are applied to G1 and G3 through a voltage combiner. The bandwidth for dc bias (ac pulses) is 30 Hz (80 MHz). We use a nanoscale on-chip integrated 40-GHz antenna to generate the ac magnetic field to drive the ESR35. The antenna is powered by a vector microwave source (Agilent E8267D PSG). The SET sensor current is initially amplified with a transimpedance amplifier (Femto DPLCA-200) with 107 V/A amplification. The amplified signal is fed into a JFET voltage amplifier (SIM 910) with gain of 50. This signal is then low-pass filtered at 100 kHz with an analogue filter (SIM 965). The amplified and filtered signal is finally readout with a digital oscilloscope (GaGe digitizer OCE838009). The sample is cooled down in an Oxford Instruments, liquid-helium-cooled, dilution refrigerator with superconducting magnet. All measurements are performed at the phonon bath temperature of 37 mK.
\({T}_{1}\) relaxation measurement
In this study, we use \({T}_{1}\) relaxation from the \(\left|\uparrow \downarrow \right\rangle\) to the \(\left|\downarrow \downarrow \right\rangle\) state as an alternative method to assess maximum readout visibilities. We first initialize the DQD system in \(\left|\uparrow \downarrow \right\rangle\) as described in Supplementary Fig. 2a. The DQD system then dwells in the (1,3) region for the \(\left|\uparrow \downarrow \right\rangle\) state to decay to the \(\left|\downarrow \downarrow \right\rangle\) state. Finally, we pulse the DQD back to the (0,4) region for spin readout. The \(\left|\uparrow \downarrow \right\rangle\) state is converted to singlet, while the \(\left|\downarrow \downarrow \right\rangle\) state is converted to triplet. As shown in Supplementary Fig. 2, the singlet probability decays exponentially with dwell time.
Electrostatic wavefunction model
The shape and size of the electron wavefunction defines the degree of overlap with nearby residual 29Si nuclear spins. We start with a calculation of the anticipated wavefunction envelope. To quantify the electron confinement in the inner (quantum) area under the G1 and G3 gates, we have performed self-consistent Schrödinger–Poisson simulations of the device. For this, we construct a virtual three-dimensional multilayer and multimaterial device geometry from the production masks and models of the fabrication steps. An image of the virtual 3D stack appears in Fig. 5a.
Internal stress is expected to build up when cooling this heterogeneous system to cryogenic temperatures. We have solved the stationary stress–strain problem for the entire layout to incorporate the resulting strain pattern into the electron potential profile as a correction48. In principle, voids or cracks could form somewhere in the physical device, thus dramatically changing the stress–strain problem, but our simulation treats all constituent layers as perfectly bonded ideal materials. Another issue is the low reliability and consistency of literature values for elastic parameters of many of the materials in the gate stack; moreover, their applicability down to the scale of tens of (and even few) nanometres is questionable. However, we find that for this device the strain-induced correction to the potential profile for electrons accumulated at the Si/SiO2 interface is up to a few meV at most, so the limited precision of this calculation is of only modest consequence given the magnitude of voltage biasing applied to the device.
We employ the Thomas–Fermi approximation to model the partitioned two-dimensional electron gas, and full quantum-mechanical treatment of one- and two-electron QD states in the inner area. Figure 5b gives one example of a simulated charge accumulation. When the gates are tuned close to the biases used in the experiments (in which the exchange \(J\) between two separated electrons is relatively low), we calculate single-electron quantization energies of \(\hslash \omega \sim\) 16 meV perpendicular to the potential trough and up to \(\sim\)11 meV along it. These quantization energies define the spatial extent of the electron eigenstate. Using \(m\approx 0.2{m}_{0}\) for the relevant electron effective mass in Si along the oxide interface, the extent \(d\) (defined here by the contour of \(1/e\) reduction of the electron charge density from its maximal value in the centre of the QD) is ~40 nm\(/\!\!\sqrt{\hslash \omega \ [\,\text{in}\,\ \,\text{meV}\,]}\), that is, the electron state would be about 10 × 12 nm2 for the quoted quantization energies. The electron is pressed towards the Si/SiO2 interface by the mean electric field F ~ 20 mV/nm. These values should be treated cautiously, since our multi-gate MOS device allows substantial flexibility in tuning. Also, in this effort, we have chosen to forego any possible contribution of potential disorder associated with the silicon-oxide interface and/or discrete charges trapped in the oxide. As such, a smaller wavefunction, as is more likely given the amount of hyperfine fluctuation, is highly plausible.
In total, our model is consistent with a pancake shaped wavefunction, as anticipated by a simpler model of a vertical triangular potential and parabolic transverse potential. For the purposes of estimating the wavefuncion to calculate hyperfine coupling parameters \({A}_{j}\) and the dipolar coupling tensor \({{\bf{D}}}_{j}\), we employ such a simplified model, shown relative to the density of 29Si for 800 p.p.m. content in a sample nuclear configuration depicted in Fig. 6. For the particular random configuration shown, 8 nuclei have \({A}_{j}/2\pi\;> \, 30\;{\mathrm{kHz}}\). Another random configuration may have more or less. The impact of various hyperfine terms varies considerably depending on where the 29Si nuclei happened to have landed relative to the small dot and its valley oscillations.
The contact coefficient \({A}_{j}\) in units of rad/sec corresponding to Eq. (1) is
Here \(\eta =178\)49 is the Bloch wavefunction overlap, and \(a=0.543\) nm is the lattice constant of silicon. The \({\cos }^{2}({k}_{0}{x}_{j}+\phi )\) term arises due to the mixing of two equivalent valley states along the growth axis, for which \({k}_{0}\) is the wavenumber at the conduction-band minimum and \(\phi\) a field-dependent phase offset, and the smooth envelope wavefunction \(\psi\) is normalized such that, when summing over all lattice sites \({r}_{k}\), \({\sum }_{k}| \psi ({{\bf{r}}}_{k}){| }^{2}{\cos }^{2}({k}_{0}{x}_{k}+\phi )=1\).
For the dipole–dipole interaction tensor, corresponding to Eq. (3), we have
where the dipole–dipole tensor is
\(\Psi ({\bf{r}})\) is the total wavefunction of the electron in the dot, and \({{\bf{r}}}_{j}\) is the location of 29Si nucleus \(j\). We break the integral into two terms.
The first term ignores envelope variation and focuses on the microscopic integral over the vicinity of the 29Si in question. We find that the symmetry of the wavefunction in the valley-mixed state leaves one of the off-diagonal components of the central-cell dipole–dipole coupling tensor non-zero, namely an in-plane \({D}_{j}^{\alpha \beta }\) term in which directions \(\alpha\) and \(\beta\) are along crystalline axes orthogonal to the growth (i.e. valley-mixed) direction. We evaluate this central-cell off-diagonal term using the plane-wave expansion of the periodic Bloch amplitude, with the numerical coefficients reported in ref. 50. Handily, integrals are dominated by the volume away from the nucleus, where the expansion is more accurate. With \(\alpha ,\beta\) along main crystal axes [1 0 0] and [0 1 0], this on-site dipolar term is estimated as
an expression notably dependent on the valley mixing phase at the nucleus. We caution that this expression is approximate, as microscopic integrals over neighbouring cells interfere with the terms we have included. For the estimate above, the ratio of the central-cell anisotropic off-diagonal term to the contact hyperfine term for a typical nucleus \(j\) is a factor of about \(1{0}^{-3}\), which is similar to the experimentally confirmed ratio of the same for many 29Si nuclear sites of a 31P donor51, with pronounced exceptions from some of the nuclei very close to the donor.
Although the presence of this term is significant, and must be included in future studies which may allow different magnetic field directions, in the present experiment the magnetic field was 45° different from the crystalline axes, under which conditions this term integrates to zero. A second, macroscopic term of the dipolar interaction will contribute; we calculate this term by fully neglecting variation in \(\Psi ({\bf{r}})\) over individual atomic cells and so replacing the integral with a sum over all atomic sites excepting the 29Si in question:
This term is generally non-zero due to finite offsets of the nuclei relative to the MOS electron, and calculated as part of the spin-flip probabilities for the model described in the Results section. We found that the distribution of dipolar term magnitudes has high variation depending on 29Si placement, resulting in the broad distribution of spin-flip rates indicated in Fig. 4.
Data availability
The data that support the findings of this study are available from the corresponding author upon reasonable request.
Code availability
The computer code used in this study are available from the corresponding author upon reasonable request.
References
Veldhorst, M. et al. An addressable quantum dot qubit with fault-tolerant control-fidelity. Nat. Nanotechnol. 9, 981 (2014).
Kawakami, E. et al. Electrical control of a long-lived spin qubit in a Si/SiGe quantum dot. Nat. Nanotechnol. 9, 666 (2014).
Takeda, K. et al. A fault-tolerant addressable spin qubit in a natural silicon quantum dot. Sci. Adv. 2, e1600694 (2016).
Tyryshkin, A. M. et al. Electron spin coherence exceeding seconds in high-purity silicon. Nat. Mater. 11, 143 (2012).
Muhonen, J. T. et al. Storing quantum information for 30 seconds in a nanoelectronic device. Nat. Nanotechnol. 9, 986 (2014).
Ladd, T. D. & Malcolm, S. C. in Encyclopedia of Modern Optics 2nd edn (eds Guenther, B. D. & Steel, D. G.) 467–477 (Elsevier, Oxford, 2018).
Watson, T. F. et al. A programmable two-qubit quantum processor in silicon. Nature 555, 633 (2018).
Zajac, D. M. et al. Resonantly driven CNOT gate for electron spins. Science 359, 439–442 (2018).
Yoneda, J. et al. A quantum-dot spin qubit with coherence limited by charge noise and fidelity higher than 99.9%. Nat. Nanotechnol. 13, 102 (2018).
Huang, W. et al. Fidelity benchmarks for two-qubit gates in silicon. Nature 569, 532 (2019).
Yang, C. H. et al. Silicon qubit fidelities approaching stochastic noise limits via pulse optimisation. Nat. Electron. 2, 151 (2019).
Xue, X. et al. Benchmarking gate fidelities in a Si/SiGe two-qubit device. Phys. Rev. X 9, 021011 (2019).
Elzerman, J. M. et al. Single-shot read-out of an individual electron spin in a quantum dot. Nature 430, 431 (2004).
Veldhorst, M., Eenink, H. G. J., Yang, C. H. & Dzurak, A. S. Silicon CMOS architecture for a spin-based quantum computer. Nat. Commun. 8, 1766 (2017).
Jones, C. et al. Logical qubit in a linear array of semiconductor quantum dots. Phys. Rev. X 8, 021058 (2018).
Maurand, R. et al. A CMOS silicon spin qubit. Nat. Commun. 7, 13575 (2016).
Hutin, L. et al. Si MOS technology for spin-based quantum computing. In 48th European Solid-State Device Research Conference (ESSDERC) 12–17 (Dresden, Germany, 2018).
Vandersypen, L. M. K. et al. Interfacing spin qubits in quantum dots and donorshot, dense, and coherent. npj Quantum Inform. 3, 34 (2017).
Baart, T. A. et al. Single-spin CCD. Nat. Nanotechnol. 11, 330 (2016).
Fujita, T., Baart, T. A., Reichl, C., Wegscheider, W. & Vandersypen, L. M. K. Coherent shuttle of electron-spin states. npj Quantum Inform. 3, 22 (2017).
Nakajima, T. et al. Coherent transfer of electron spin correlations assisted by dephasing noise. Nat. Commun. 9, 2133 (2018).
Fogarty, M. A. et al. Integrated silicon qubit platform with single-spin addressability, exchange control and single-shot singlet-triplet readout. Nat. Commun. 9, 4370 (2018).
Sigillito, A. J., Gullans, M. J., Edge, L. F., Borselli, M. & Petta, J. R. Coherent transfer of quantum information in silicon using resonant swap gates. Preprint at https://arxiv.org/abs/1906.04512 (2019).
Johnson, A. C., Petta, J. R., Marcus, C. M., Hanson, M. P. & Gossard, A. C. Singlet-triplet spin blockade and charge sensing in a few-electron double quantum dot. Phys. Rev. B 72, 165308 (2005).
West, A. et al. Gate-based single-shot readout of spins in silicon. Nat. Nanotechnol. 14, 437 (2019).
Pakkiam, P. et al. Single-shot single-gate rf spin readout in silicon. Phys. Rev. X 8, 041032 (2018).
Urdampilleta, M. et al. Gate-based high fidelity spin read-out in a cmos device. Nat. Nanotechnol. 14, 737–741 (2019).
Zheng, G. et al. Rapid gate-based spin read-out in silicon using an on-chip resonator. Nat. Nanotechnol. 14, 742–746 (2019).
Schaal, S. et al. A cmos dynamic random access architecture for radio-frequency readout of quantum devices. Nat. Electron. 2, 236–242 (2019).
Pioro-Ladriere, M. et al. Electrically driven single-electron spin resonance in a slanting Zeeman field. Nat. Phys. 4, 776 (2008).
Ito, T. et al. Four single-spin Rabi oscillations in a quadruple quantum dot. Appl. Phys. Lett. 113, 093102 (2018).
Crippa, A. et al. Gate-reflectometry dispersive readout and coherent control of a spin qubit in silicon. Nat. Commun. 10, 2776 (2019).
Brauns, M., Amitonov, S. V., Spruijtenburg, P. C. & Zwanenburg, F. A. Palladium gates for reproducible quantum dots in silicon. Scientific Rep. 8, 5690 (2018).
Itoh, K. M. & Watanabe, H. Isotope engineering of silicon and diamond for quantum computing and sensing applications. MRS Commun. 4, 143–157 (2014).
Dehollain, J. P. et al. Nanoscale broadband transmission lines for spin qubit control. Nanotechnology 24, 015202 (2012).
Yang, C. H., Lim, W. H., Zwanenburg, F. A. & Dzurak, A. S. Dynamically controlled charge sensing of a few-electron silicon quantum dot. AIP Adv. 1, 042111 (2011).
Harvey-Collard, P. et al. High-fidelity single-shot readout for a spin qubit via an enhanced latching mechanism. Phys. Rev. X 8, 021046 (2018).
Nakajima, T. et al. Robust single-shot spin measurement with 99.5% fidelity in a quantum dot array. Phys. Rev. Lett. 119, 017701 (2017).
Rao, C. R. & Statistiker, M. Linear Statistical Inference and Its Applications Vol. 2 (Wiley, New York, 1973)
Reilly, D. J. et al. Measurement of temporal correlations of the overhauser field in a double quantum dot. Phys. Rev. Lett. 101, 236803 (2008).
Reilly, D. J. et al. Exchange control of nuclear spin diffusion in a double quantum dot. Phys. Rev. Lett. 104, 236802 (2010).
Delbecq, M. R. et al. Quantum dephasing in a gated gaas triple quantum dot due to nonergodic noise. Phys. Rev. Lett. 116, 046802 (2016).
Assali, L. V. C. et al. Hyperfine interactions in silicon quantum dots. Phys. Rev. B 83, 165301 (2011).
Abragam, A. Principles of Nuclear Magnetism Ch. IX.III.B (Oxford, 1961).
Fu, K.-M. C., Ladd, T. D., Santory, C. & Yamamoto, Y. Optical detection of a single nuclear spin. Phys. Rev. B 69, 125306 (2004).
Pla, J. J. et al. Coherent control of a single 29Si nuclear spin qubit. Phys. Rev. Lett. 113, 246801 (2014).
Hensen, B. et al. A silicon quantum-dot-coupled nuclear spin qubit. Preprint at https://arxiv.org/abs/1904.08260 (2019).
Thorbeck, T. & Zimmerman, N. M. Formation of strain-induced quantum dots in gated semiconductor nanostructures. AIP Adv. 5, 087107 (2015).
Wilson, D. K. Electron spin resonance experiments on shallow donors in germanium. Phys. Rev. 134, A265 (1964).
Saraiva, A. L. et al. Intervalley coupling for interface-bound electrons in silicon: an effective mass study. Phys. Rev. B 84, 155320 (2011).
Ivey, J. L. & Mieher, R. L. Ground-state wave function for shallow-donor electrons in silicon. II. Anisotropic electron-nuclear-double-resonance hyperfine interactions. Phys. Rev. B 11, 849–857 (1975).
Acknowledgements
We thank W. Huang for enlightening discussions and A. Saraiva for helpful comments on the 29Si nuclear spin modelling. We acknowledge support from the Australian Research Council (CE170100012), the US Army Research Office (W911NF-17-10198) and the NSW Node of the Australian National Fabrication Facility. The views and conclusions contained in this document are those of the authors and should not be interpreted as representing the official policies, either expressed or implied, of the Army Research Office or the US Government. The US Government is authorized to reproduce and distribute reprints for Government purposes notwithstanding any copyright notation herein. B.H. acknowledges support from the Netherlands Organization for Scientific Research (NWO) through a Rubicon Grant. K.M.I. acknowledges support by Spintronics Research Network of Japan. K.Y.T. acknowledges support from the Academy of Finland through Project Nos. 308,161, 314,302, and 316,551. T.D.L. acknowledges support from the Gordon Godfrey Bequest sabbatical grant
Author information
Authors and Affiliations
Contributions
R.Z. and T.T. performed the experiments. K.Y.T., K.W.C., J.C.C.H. designed the device, fabricated by K.Y.T. and F.E.H. with A.S.D.’s supervision. K.M.I. prepared and supplied the 28Si epi layer. R.Z., T.T., B.H., C.H.Y., R.C.C.L. and W.G. contributed to the preparation of experiments. R.Z., T.T., B.H. and A.S.D. designed the experiments, with T.D.L., A.A.K., A.L., A.M. contributing to results discussion and interpretation. T.D.L. performed 29Si nuclear spin simulation with assistance from AAK. R.Z., A.L., T.D.L. and A.S.D. wrote the manuscript with input from all co-authors.
Corresponding authors
Ethics declarations
Competing interests
This work was funded, in part, by Silicon Quantum Computing Proprietary Limited.
Additional information
Peer review information Nature Communications thanks Ryan Jock and the other, anonymous, reviewer(s) for their contribution to the peer review of this work.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhao, R., Tanttu, T., Tan, K.Y. et al. Single-spin qubits in isotopically enriched silicon at low magnetic field. Nat Commun 10, 5500 (2019). https://doi.org/10.1038/s41467-019-13416-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-019-13416-7
- Springer Nature Limited
This article is cited by
-
Non-symmetric Pauli spin blockade in a silicon double quantum dot
npj Quantum Information (2024)
-
Coherence of a field gradient driven singlet-triplet qubit coupled to multielectron spin states in 28Si/SiGe
npj Quantum Information (2024)
-
Bounds to electron spin qubit variability for scalable CMOS architectures
Nature Communications (2024)
-
High-fidelity spin qubit operation and algorithmic initialization above 1 K
Nature (2024)
-
Compilation and scaling strategies for a silicon quantum processor with sparse two-dimensional connectivity
npj Quantum Information (2023)