Abstract
Cornstarch in water exhibits impact-activated solidification (IAS) and strong discontinuous shear thickening, with “shear jamming”. However, these phenomena are absent in cornstarch in ethanol. Here we show that cornstarch granules swell under ambient conditions. We postulate that this granule swelling is linked to an interparticle force scale that introduces a discontinuous rate-dependence to the generation of stable contacts between granules. We studied this force scale by coating sand with ~ 2 μm-thick polydimethysiloxane, creating a material that exhibits a similar IAS and discontinuous deformation rate-stiffening despite being a granular composite, not a suspension. This result suggests rate-dependence can be tuned by coating granular materials, introducing an interparticle force scale from rate-dependent properties present in the coating material. Our work provides insights into the unique behavior of cornstarch in water, bridges our understanding of suspensions and dry granular materials, and introduces a method to make discontinuous rate-dependent materials without suspending particles.
Similar content being viewed by others
Introduction
Cornstarch in water shows non-Newtonian behavior: impact-activated solidification (IAS), where a high-speed intruder is stopped by the rapid solidification of the underlying suspension1, and discontinuous shear thickening (DST), where increasing shear rates leads to a sudden increase in viscosity that spans several orders of magnitude2. This type of non-Newtonian response can be highly desirable, in the case of flexible body armor3,4, or highly undesirable, such as in industrial processes with confining flow, where increasing flow rates constricts the flow5. Despite a number of studies on the properties of cornstarch in water, the underlying mechanism for its unusually strong response under shear compared to typical shear thickening suspensions6,7 and “shear jamming” response8,9 has been elusive: hydrodynamic forces10,11, dilatancy12,13, and shear jamming14,15 have all been suggested to play a role in DST. This lack of understanding of the underlying mechanisms involved makes it prohibitive to explore the material design space in order to make new materials with strongly discontinuous rate-dependent properties. In addition, it is difficult to take effective measures to prevent DST in suspensions when it is not desired.
Here we show that IAS and DST in aqueous cornstarch suspensions are strongly influenced by a previously unexplored phenomenon, namely that cornstarch swells appreciably in water under ambient conditions, which alters its mechanical properties. We postulate that this swelling introduces a granule-level force scale that (1) allows for strong frictional contacts to form, and (2) leads to a discontinuous deformation rate-dependence on stiffness/viscosity via a granule-level force scale. We modeled this granule-level force scale using fine, ~ 60–250 μm-diameter, sand coated with a ~ 2 μm-thick layer of polydimethylsiloxane (PDMS), which gives rise to a rate-dependent force scale modulated by the viscoelastic properties of PDMS. This model PDMS-coated sand exhibits qualitatively similar behavior to cornstarch and water, namely impact-activated solidification/jamming and discontinuous-like deformation rate-stiffening. However, it remains distinctly a dry granular material rather than a suspension. Our finding gives insight into IAS and DST in suspensions, suggests similarities between suspensions and dry granular materials, and provides a blueprint for creating strongly deformation rate-dependent materials with no suspending fluid.
Results
Swelling of cornstarch in water
Cornstarch in water is a classic discontinuously shear thickening suspension. However, despite its popularity and ubiquity, we find that it has unique properties. For example, cornstarch swells in water under ambient conditions (see Supplementary Information for video). Under optical microscopy, we observed a ~ 12% swelling in diameter or ~ 40% by volume (Fig. 1). This swelling is unobserved for cornstarch in ethanol, a slightly weaker polar protic solvent compared to water (dipole moment: 1.69 Debye versus 1.85 Debye). We observed that adding cornstarch to water produces an exothermic reaction, releasing ~ 45.3 J/g of cornstarch in 100 ml of water. In contrast, adding cornstarch to the same volume of ethanol is endothermic, consuming ~ 24.2 J/g of cornstarch (see Supplementary Information for video). This suggests that swelling of cornstarch is energetically favorable in water and unfavorable in ethanol, which explains the absence of swelling in cornstarch–ethanol at room temperatures. To quantify this swelling in terms of a change in overall volume fraction of cornstarch, we repeatedly mixed cornstarch with water inside of a graduated cylinder and observed a total volume increase of ~11 ± 2% (of cornstarch volume before swelling), instead of ~ 40% (see Methods for details). This means that the cornstarch granules absorb some of the surrounding water during swelling, ultimately resulting in a volume fraction increase of ~11%. One previous study has found that cornstarch in water is porous, which is in agreement with our observation of cornstarch swelling16. These findings suggest two unique properties of cornstarch–water suspensions: (1) granule swelling increases the actual packing fraction of the cornstarch–water suspension by ~11%, and (2) this swelling may alter the mechanical properties of cornstarch granules. Due to this swelling effect of cornstarch in water, henceforth we denote the volume fraction before swelling as φnom, and denote the packing fraction calculated accounting for swelling as φact.
Impact experiments on cornstarch suspensions
To test the effect of cornstarch swelling on mechanical properties, we performed impact experiments on cornstarch and water mixture, and cornstarch and ethanol mixture, which showed that cornstarch and ethanol mixture loses its shear thickening behavior (Fig. 2). We dropped a 6.35-cm-diameter disk intruder (thickness: 1.1 cm and mass: 291 g) into cornstarch–water and cornstarch–ethanol mixtures (φnom ~ 45% for both), and tracked its depth and velocity as a function of time (see Supplementary Figures 1 and 2 and Supplementary Note 1 for setup). For the cornstarch aqueous suspension, the intruder impacted the surface at ~ 3 m/s and rebounded, indicating that the suspension became solid-like and reacted elastically to the impact. In contrast, the intruder impacting into the ethanol solution encountered minimal resistance, quickly sinking to the bottom of the container. Increasing cornstarch–ethanol packing fraction to φact ~ 54% does not resolve this qualitative difference in response to impacts, nor does accounting for granule swelling (Fig. 2b). In every case that we have accounted for, i.e., φnom from 43 to 47% for cornstarch–water mixture and φnom = φact from 43 to 54% for cornstarch–ethanol mixture, cornstarch in water reacts strongly to impact and is able to repel the intruder, while cornstarch in ethanol behaves qualitatively similar to a granular material in a fluid, resisting the intruder only when the packing fraction is high enough for a solid packing (i.e., greater than random loose packing (RLP), φ ~ 54%). This highly solvent-dependent behavior suggests that cornstarch granules may have different structural properties in water compared to in ethanol, and that this structural difference is essential for the emergence of IAS and likely DST.
The swelling that we observed in cornstarch–water suspensions suggests that many previous studies on cornstarch in water likely involved higher packing fractions than the reported values, as φ is typically estimated based on bulk densities2,17. This may explain why many studies have observed DST in cornstarch–water suspensions at consistently low packing fractions, below where jamming can occur. Typical cornstarch–water packing fractions, φnom ~ 45–48%2,9, at the emergence of DST are appreciably lower than random loose packing (RLP), φ ~ 55%18, and random close packing (RCP), φ ~ 64%19. They are also comparatively lower than the φ of emergent DST in other suspensions, e.g., glass beads in mineral oil2, polystyrene beads in aqueous solution20, and polyvinyl chloride in Dinch and mineral oil21. Cornstarch–water suspensions are thought to exhibit “shear jamming”, where a solid-like state is reached under shear without compression14,15. However, granular shear jamming occurs at relatively high packing fractions, between RLP and isotropic jamming8. Particle packings below RLP typically do not satisfy isostaticity or rigidity percolation18 and cannot support mechanical load through stable frictional contacts, which play a crucial role in DST, as shown in simulations22. Our observation of granule swelling suggests that the actual packing fraction at which DST occurs in cornstarch suspensions is likely much higher, φact,c ~ 50–53%, providing a pathway for shear jamming to occur and potentially reconciling this discrepancy.
Rate-dependent stiffness of cornstarch–water mixture
While the packing fraction is important in determining whether shear thickening occurs, it cannot explain the dramatic difference in behavior between cornstarch in water and cornstarch in ethanol. How does granule swelling affect the mechanical properties of cornstarch, and how does it have a dramatic effect on the rheology of cornstarch suspensions? We explored these questions by performing flat-punch indentation tests on dense suspensions/packings of cornstarch granules in water and in ethanol with packing fractions from φact ~ 53–55%, after swelling (Fig. 3, see Methods for details). With this experiment, we have precise control over the deformation rate, and we can directly measure the stiffness response of our suspensions, giving us a pathway to probe a deformation rate-response that is related to both DST and IAS.
We found that cornstarch in water exhibits a discontinuous deformation rate-dependent response, with elastic modulus increasing by several orders of magnitude over a displacement rate range of less than one order of magnitude (modulus calculated from contact mechanics, see Methods). At φact ~ 53% (accounting for swelling), we observed that cornstarch in water behaves like a fluid at displacement rates below ~ 0.2 mm/s (zero stiffness), but sharply develops a nonzero stiffness, becoming solid-like, above a displacement rate of ~ 0.5 mm/s. Increasing the packing fraction by 1% to φact ~ 54% (close to RLP) changes the suspension into a loose packing of cornstarch and water, where the system has a finite elastic modulus (~ 2 MPa) for displacement rates from 0.01 to 0.05 mm/s, where modulus begins to increase discontinuously with displacement rate. This strongly rate-dependent response is absent in cornstarch in ethanol, where E increases by a factor of ~ 4 over more than three orders of magnitude of displacement rates. Dry cornstarch results are not shown due to limitations in force resolution, which prevented reliable results for dry cornstarch. Preliminary results indicated that dry cornstarch has no rate-dependence.
Lubrication forces present a barrier to frictional contacts in smooth and hard particles9,21,22, but a soft (and rough) shell originating from granule swelling may provide a pathway to overcome those forces. We postulate that the mechanical changes induced by granule swelling in water contributes to its DST and IAS in suspension by introducing a force scale to the interparticle contacts: the rate at which the suspension is deformed dictates the emergence of interparticle friction. In other words, swelled cornstarch granules are repelled by lubrication at low deformation rates, but at high deformation rates, frictional contacts can form owing to granule-level changes induced by their swelling. This suggests that DST and IAS are both related to an underlying force scale, which allows for a suspension to behave fluid-like when slowly deformed and transition to solid-like at fast deformation rates. This transition to solid-like behavior may also be tied to shear jamming of the granules. For native cornstarch, there is likely no mechanism for overcoming lubrication forces, as observed by an absence of shear thickening in cornstarch–ethanol suspensions.
Discontinuous rate-stiffening in a granular composite
An interparticle force scale is crucial in bringing about DST in various models23,24, but it has been difficult to probe experimentally, as small-scale mechanical tests on particles in suspension are difficult to perform. To test the ubiquity of a force scale model, we fabricated a composite material composed of ~ 60–250 μm-diameter polydisperse fine sand coated with ~ 7.5% by volume cross-linked polydimethylsiloxane (PDMS) (see Fig. 4a for diagram and Methods for fabrication details). This PDMS-coated sand has a hard core provided by the sand particles, most of which is quartz, which has E ~ 70 GPa, and a soft ~ 2 μm-thick viscoelastic outer layer of PDMS, estimated from volume fraction. This composite sand has a force scale that originates from viscoelasticity rather than lubrication: at low deformation rates, loose sand grains can rearrange under small stresses, while at high deformation rates, the outer PDMS stiffens, bringing the sand grains into stable contact and temporarily forming a jammed network, with the hard particle cores providing a backbone for carrying the majority of the stress.
To show this, we performed impact experiments and flat-punch indentation tests. In impact experiments, bare sand is highly dissipative, absorbing the energy from the intruder upon impact and quickly stopping its progress. In contrast, the PDMS-coated sand responds elastically to the intruder, which rebounds several times after impact (Fig. 4b and see Supplementary Information for high-speed videos). This observation suggests that a viscoelastic coating on a stiff granular material imparts viscoelasticity to the overall composite through an IAS-like process where the grains jam under high deformation rates (~ 2.9 m/s). Mechanical flat-punch indentation experiments revealed that the PDMS-coated sand has a nonlinear response to increasing displacement rates with a narrow range of displacement rates over which E increases by nearly an order of magnitude from 0.1 to 0.5 mm/s (Fig. 4c). This rate-dependence is absent in bare sand, where E remains roughly unchanged for all deformation rates. The PDMS coating increases the E of the coated sand at lower displacement rates, likely because of the interparticle cohesion introduced by the viscoelastic PDMS layer. The form of the rate-dependent response of the PDMS-coated sand (Fig. 4c) resembles that of the cornstarch and water mixture (Fig. 3), exhibiting a narrow range of displacement rates over which the E increases rapidly. The response of PDMS-coated sand is also qualitatively different from that of native PDMS under indentation (Fig. 4d), which has a constant slope of ~ 0.8 when plotted in log(E) vs. log(displacement rate).
We attribute the similarities between aqueous cornstarch suspensions and PDMS-coated sand to the presence of a force scale. In the case of cornstarch, the force scale is related to the swelling, which may serve to allow granules to overcome lubrication, and in the case of coated sand, the outer PDMS layer introduces a viscoelastic force scale, which modulates the quality of interparticle contacts, from soft and cohesive at low deformation rates to elastic and shear jammed at high deformation rates. We are unable to perform direct and accurate measurement of such a force scale at the particle level, but we can estimate the macroscopic stresses involved. For our cornstarch–water mixture, we estimate a macroscopic stress scale of ~ 20 Pa by measuring viscosity of the mixture under different shear rates (see Supplementary Figure 3 in Supplementary Information). This is in line with previous measurements for cornstarch and water25,26. For PDMS-coated sand, we estimate a critical force scale of ~ 4 μN in particle–particle contact. This value is estimated by calculating the contact force needed for bringing two approximately spherical sand cores (diameter ~ 155 μm) together (displacement of ~ 4 μm) with an effective modulus equal to the outer PDMS layer, which has an elastic modulus of ~ 100 kPa corresponding to a critical displacement rate of ~ 0.2 mm/s (Fig. 4c, d).
Discussion
Interparticle contacts are essential for the emergence of DST in simulations22, but smooth hard particles are repelled from contact by the lubrication singularity. In theory, particle roughness can help to overcome lubrication and has a dramatic effect on the rheology23,27, and in colloidal experiments, smooth particles are largely contactless, without DST, while rough particles readily form load-bearing contacts under shear28. There are also studies that suggest dangling polymers appear on cornstarch surfaces29 and interparticle hydrogen bonding occurs30. Clearly, the quality of interparticle interactions is important for suspension rheology. Our results show that, for cornstarch, solvent chemistry influences granule mechanical properties, altering interparticle interactions and suspension rheology. Specifically, the DST and IAS observed in cornstarch suspensions is strongly linked to cornstarch swelling in water. In cornstarch and ethanol mixtures, we find no swelling and no DST or IAS. A number of models and theories have suggested the existence of a force scale that originates from interparticle lubrication14,23,24. We postulate that cornstarch swelling is essential for the emergence of this force scale, which is responsible for the unique rheological properties of cornstarch in water. In other suspensions, a force scale may emerge from alternative sources. For example, stabilizing coatings such as steric layers in colloids impart a soft polymer outer layer, and such coatings are often essential for making stable, dispersed suspensions.
Expanding on the idea of an interparticle force scale, we artificially introduced a force scale in sand by coating it with a thin ~ 2 μm viscoelastic PDMS layer, which imparted a DST/IAS-like rate-dependence to the otherwise dissipative sand. Our composite granular material is qualitatively different from both native PDMS and native sand: (1) the stiffness of PDMS-coated sand is systematically higher than native PDMS and sand across all deformation rates, likely due to interparticle cohesion, and (2) the stiffness of PDMS-coated sand exhibits a sharply increasing region, i.e., from 0.1 to 0.5 mm/s in displacement rate, which is absent in both PDMS and bare sand. Future deformation rate-stiffening materials may utilize this insight for improving on flexible materials that respond dramatically to impacts. For example, the motif of a stiff granular material coated with a thin viscoelastic material can lead to flexible body armors that do not need density matching, steric stabilization, or suspending fluids, freeing up limitations on the properties of available solutes and solvents and significantly reducing the overall weight. One such example would be aluminum or diamond powder coated with PDMS for a lightweight, flexible, yet tough and highly rate-stiffening material.
Methods
Water absorption measurement
For measuring the correct packing fraction of our cornstarch and water mixture that incorporates both effects of cornstarch swelling and water absorption by cornstarch, we first measure the mass of cornstarch and calculate its volume with the density of cornstarch taken to be ρc ~ 1.59 g cm−3, as reported by Brown et al.2. We then prepare water of ~ 1.5 times the volume of dry cornstarch in a graduated cylinder to ensure a well-mixed state (see Supplementary Table 1 and Supplementary Note 2). The total volume change is calculated by comparing the measured volume, Vm, to the sum of the water volume and dry cornstarch volume, Vw + Vc. From this comparison, we found an ~ 11% increase in Vc, i.e., Vm = Vw + 1.11Vc, as Vw remains constant. This coupled with our direct measurements of cornstarch swelling suggests that cornstarch absorbs water during the swelling process, resulting in an overall ~ 11% increase in cornstarch volume.
For a thought experiment, suppose our null hypothesis is that no swelling occurs. The cornstarch density under that hypothesis would be ρc/1.11 = 1.43 g cm−3. Since this density value is well outside of the range of measured values for cornstarch density (1.5–1.62 g cm−3)2,14,16,17, we reject the null hypothesis. This is another observation that supports the finding that cornstarch volume increases from adding water.
Suspension impact experiments
We dropped a metal disc from varying heights into a cornstarch suspension (water and ethanol) with packing fractions φnom ~ 45% (the packing fraction is calculated with a cornstarch bulk density of 1.59 g cm−3). We guided the disk with a chute located above the container, which has photoelastic gelatin boundaries. We used these boundaries to track the force propagation during impact (see Supplemental Materials). The disk had a diameter of 63.5 mm, width 11 mm, and mass 291 g. We recorded impacts with a Photron FAST-CAM SA5. We tracked the impactor using a circular Hough transform at each video frame, and numerically computed the velocity (refer to Supplementary Information for additional information and photoelastic data).
Flat-punch indentation experiments
Flat-punch indentation experiments were conducted with a TA instruments RSA III microstrain analyzer and indented with a 8-mm-cylindrical flat punch at two displacement rates, 0.05 and 4 mm/s. Packings of cornstarch in water and ethanol were made by adding solvent into granular cornstarch. In the case for water, we mixed the water and first allowed it to be absorbed. Experiments were conducted after the mixture settled into granular packing.
For flat-punch contact mechanics calculations, we used a standard rigid cylindrical indenter into flat plane scenario:
where F is the normal force, a is the cylinder radius (4 mm), d is the indentation depth, and E ~ E*3/4, assuming ν ~ 0.5 and a very stiff cylinder (brass).
For sand particle–particle contact force scale estimate, we used a contact between two spheres:
where F is the normal force, E ~ E*3/2, R is the effective radius (1/2 the particle radius), and d is the displacement.
Coating PDMS on sand
Polydimethylsiloxane-coated sand was prepared by first desiccating and heating fine sand at ~ 180 °C. Afterward, 7.5% by bulk volume hydroxyl-terminated PDMS was introduced and mixed with the sand until the sand was uniformly coated. We pre-dissolved boric acid in ethanol and introduced an ~ 0.5% by bulk volume (of boric acid) into the PDMS-coated sand, mixing the dissolved boric acid as the ethanol solvent evaporates. This concentration is not crucial—it is only important to include enough boric acid to crosslink all of the PDMS. After the PDMS cross-links and the mixture cools, we introduced ~ 2% by PDMS volume of oleic acid to act as a plasticizer for PDMS.
Fabrication of native PDMS
Native PDMS used in flat-punch test was prepared in a similar way. Approximately 6.7% of boric acid by bulk volume was introduced to hydroxyl-terminated PDMS, which was preheated to ~ 180 °C. After the PDMS cross-links and the mixture cools, we introduced ~ 2% by PDMS volume of oleic acid to act as a plasticizer.
Code availability
The Code that support the findings of this study are available from the corresponding author upon reasonable request.
References
Lim, M. X., Bares, J., Zheng, H. & Behringer, R. P. Force and mass dynamics in non-Newtonian suspensions. Phys. Rev. Lett. 119, 184501 (2017).
Brown, E. & Jaeger, H. M. Dynamic jamming point for shear thickening suspensions. Phys. Rev. Lett. 103, 086001 (2009).
Lee, Y. S., Wetzel, E. D. & Wagner, N. J. The ballistic impact characteristics of Kevlar (R) woven fabrics impregnated with a colloidal shear thickening fluid. J. Mater. Sci. 38, 2825–2833 (2003).
Hasanzadeh, M. & Mottaghitalab, V. The role of shear-thickening fluids (STFs) in ballistic and stab-resistance improvement of flexible armor. J. Mater. Eng. Perform. 23, 1182–1196 (2014).
Feys, D., Verhoeven, R. & De Schutter, G. Why is fresh self-compacting concrete shear thickening? Cem. Concr. Res 39, 510–523 (2009).
Barnes, H. A. Shear-thickening (dilatancy) in suspensions of nonaggregating solid particles dispersed in Newtonian liquids. J. Rheol. 33, 329–366 (1989).
Cheng, X., McCoy, J. H., Israelachvili, J. N. & Cohen, I. Imaging the microscopic structure of shear thinning and thickening colloidal suspensions. Science 333, 1276–1279 (2011).
Bi, D. P., Zhang, J., Chakraborty, B. & Behringer, R. P. Jamming by shear. Nature 480, 355–358 (2011).
Fall, A. et al. Macroscopic discontinuous shear thickening versus local shear jamming in cornstarch. Phys. Rev. Lett. 114, 098301 (2015).
Wagner, N. J. & Brady, J. F. Shear thickening in colloidal dispersions. Phys. Today 62, 27–32 (2009).
Foss, D. R. & Brady, J. F. Structure, diffusion and rheology of Brownian suspensions by Stokesian dynamics simulation. J. Fluid. Mech. 407, 167–200 (2000).
Woodcock, L. V. Origins of shear dilatancy and shear thickening phenomena. Chem. Phys. Lett. 111, 455–461 (1984).
Smith, M. I., Besseling, R., Cates, M. E. & Bertola, V. Dilatancy in the flow and fracture of stretched colloidal suspensions. Nat. Commun. 1, 114 (2010).
Peters, I. R., Majumdar, S. & Jaeger, H. M. Direct observation of dynamic shear jamming in dense suspensions. Nature 532, 214 (2016).
Han, E. D., Wyart, M., Peters, I. R. & Jaeger, H. M. Shear fronts in shear-thickening suspensions. Phys. Rev. Fluids 3, 073301 (2018).
Han, E., Van, Ha,N. & Jaeger, H. M. Measuring the porosity and compressibility of liquid-suspended porous particles using ultrasound. Soft Matter 13, 3506–3513 (2017).
von Kann, S., Snoeijer, J. H., Lohse, D. & van der Meer, D. Nonmonotonic settling of a sphere in a cornstarch suspension. Phys. Rev. E 84, 060401 (2011).
Onoda, G. Y. & Liniger, E. G. Random loose packings of uniform spheres and the dilatancy onset. Phys. Rev. Lett. 64, 2727–2730 (1990).
Baus, M. & Colot, J. L. The hard-sphere glass—metastability versus density of random close packing. J. Phys. C. Solid State 19, L135–L139 (1986).
Fall, A., Lemaitre, A., Bertrand, F., Bonn, D. & Ovarlez, G. Shear thickening and migration in granular suspensions. Phys. Rev. Lett. 105, 268303 (2010).
Comtet, J. et al. Pairwise frictional profile between particles determines discontinuous shear thickening transition in non-colloidal suspensions. Nat. Commun. 8, 15633 (2017).
Seto, R., Mari, R., Morris, J. F. & Denn, M. M. Discontinuous shear thickening of frictional hard-sphere suspensions. Phys. Rev. Lett. 111, 218301 (2013).
Wyart, M. & Cates, M. E. Discontinuous shear thickening without inertia in dense non-Brownian suspensions. Phys. Rev. Lett. 112, 098302 (2014).
Fernandez, N. et al. Microscopic mechanism for shear thickening of non-Brownian suspensions. Phys. Rev. Lett. 111, 108301 (2013).
Fall, A., Huang, N., Bertrand, F., Ovarlez, G. & Bonn, D. Shear thickening of cornstarch suspensions as a reentrant jamming transition. Phys. Rev. Lett. 100, 018301 (2008).
Hermes, M. et al. Unsteady flow and particle migration in dense, non-Brownian suspensions. J. Rheol. 60, 905–916 (2016).
Zhao, Y. & Davis, R. H. Interaction of two touching spheres in a viscous fluid. Chem. Eng. Sci. 57, 1997–2006 (2002).
Hsiao, L. C. et al. Rheological state diagrams for rough colloids in shear flow. Phys. Rev. Lett. 119, 158001 (2017).
Galvez, L. O., de Beer, S., van der Meer, D. & Pons, A. Dramatic effect of fluid chemistry on cornstarch suspensions: linking particle interactions to macroscopic rheology. Phys. Rev. E 95, 030602 (2017).
James, N. M., Han, E. D., de la Cruz, R. A. L., Jureller, J. & Jaeger, H. M. Interparticle hydrogen bonding can elicit shear jamming in dense suspensions. Nat. Mater. 17, 965 (2018).
Acknowledgements
We thank Joshua A. Dijksman and Heinrich M. Jaeger for their insightful discussions. This work was supported by NSFC Grant No. 41672256 (H.Z.), NSF Grant No. DMR1206351 and DMR1809762, ARO Grant No. W911NF-18-1-0184, NASA Grant No. NNX15AD38G, the William M. Keck Foundation, a RT-MRSEC fellowship.
Author information
Authors and Affiliations
Contributions
H.Z. designed and performed the impact experiments with input from D.W. D.Z.C., H.Z. and D.W. designed and performed the rheology experiments. DZC fabricated the coated sand with help from D.W. D.Z.C., H.Z. and D.W. designed and performed the indentation experiments. D.Z.C., H.Z. and D.W. performed the microscopy experiments and analysis. R.P.B. supervised the experiments. D.Z.C. wrote the manuscript with input from R.P.B., H.Z. and D.W.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Journal peer review information: Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Chen, D.Z., Zheng, H., Wang, D. et al. Discontinuous rate-stiffening in a granular composite modeled after cornstarch and water. Nat Commun 10, 1283 (2019). https://doi.org/10.1038/s41467-019-09300-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-019-09300-z
- Springer Nature Limited
This article is cited by
-
Insights into the dynamic and thermal characteristics of rockslide motion: a model experiment
Acta Geotechnica (2022)
-
Jamming by shear in a dilating granular system
Granular Matter (2019)